Read instructions Pan combo (Page 2) text version

LTIP/TY-LA1000

REPLACEMENT LAMP FOR PANASONIC ® LCD REAR PROJECTION TELEVISION

. CAUTION:totothe televisionlampwait approximatelyuse;minutessoorcan cause allow forburns. Priorlampremoving lamp, switch off the Do not attempt remove the immediately after doing serious to power supply and 60 more to complete cooling. . Avoid touching the glass portion(s) ofthat gloveswithworn when replacing the lamp.and dust may cause early lamp failure and/or the lamp bare hands; fingerprints, dirt image obscurity. It is recommended be . When transporting the replacement lamp, use the box that is provided to avoid breakage. WARNING: . To avoid overheating and/or fire, ensure that the replacement lamp is mounted securely. . The lamp contains mercury. Dispose of it in accordance with local environmental regulations. For disposal or recycling

information, contact your local authorities or see www.lamprecycle.org.

REPLACING THE LAMP

MODELS PT-50LC13/PT-60LC13/PT-50LCX63/PT-60LCX63/PT-43LCX64/ PT-50LCX64/PT-60LCX64/PT-43LC14/PT-50LC14/PT-60LC14

3. Loosen the lamp cover screw. After reading the caution and warning labels on the lamp cover, loosen the lamp cover screw using a screwdriver.

POWER

+ _ VOL

POWER button/ POWER indicator Lamp Unit Handle Lamp Unit Screw

LAMP indicator

v

1. Switch off power to the television, wait until the power indicator stops blinking red, then unplug the power cord from the wall outlet. Allow the television to cool for at least 1 hour. [If the lamp must be replaced more urgently:] The projection display has a feature for forced cooling. During the first minute of the normal cooling fan operation after the POWER button is turned OFF, press the VOL+ button on the projection display and the L button on the remote control simultaneously for more than 5 seconds. The cooling fan will operate for approximately 10 minutes. The LAMP indicator will flash red 5 times every 5 seconds.

Front cover

2. Remove the front cover. Place your fingertips under the front cover and pull it from the projection display.

RESETTING THE LAMP TIMER

PT-50LC13/PT-60LC13/PT-50LCX63/PT-60LCX63/PT-43LCX64/PT-50LCX64/PT-60LCX64/PT-43LC14/PT-50LC14/PT-60LC14 WARNING: Only reset the lamp timer when the lamp has been replaced. 1. Plug the power cord back into a properly grounded wall outlet. Then press the POWER button on the projection display or the remote control to turn the power on.

UNIT REMOTE CONTROL

+ _

VOL

For models PT-50LC13/ PT-60LC13/PT-50LCX63/ PT-60LCX63/PT-43LCX64/ PT-50LCX64/PT-60LCX54

PIP

2. While pressing the VOL- button on the projection display, hold down the PIP or SPLIT button on the remote control simultaneously for more than 5 seconds.

v

CH

4. Loosen the lamp unit screw. Using a screwdriver, loosen the lamp unit screw. Grasp the lamp unit handle and slowly pull the lamp unit from the projection display.

5. Insert the new lamp unit, paying attention to the direction of insertion. Press on the lamp unit handle, ensuring that the insertion is done correctly. Dispose of the old lamp in accordance with local environmental regulations. Tighten the lamp unit screw and the lamp cover screw using a screwdriver. Replace front cover. [Note: Ensure that the lamp unit and lamp unit housing doors are attached securely. If not, the protective circuit will be activated and the power will not turn on.]

LAMP TIME WAS RESET TO 0.

For models PT-43LC14/ PT-50LC14/PT-60LC14

SPLIT PLAY

3. When the lamp time reset procedure is complete, the above screen will appear. (This screen may be different from the actual screen.) Note: When the lamp time reset is complete, the LAMP indicator goes out. p. 1

Panasonic ® is a registered trademark of Panasonic Corporation.

L

REPLACING THE LAMP

MODELS PT-44LCX65 / PT-52LCX65 / PT-61LCX65 / PT-52LCX15 Lamp Unit Screw Lamp Unit Handle

POWER button/ LAMP indicator POWER indicator 1. Switch off power to the television, wait until the power indicator stops blinking red, then unplug the power cord from the wall outlet. Allow the television to cool for at least 1 hour. [If the lamp must be replaced more urgently:] The Projection display has a feature for forced cooling. During the first minute of the normal cooling fan operation after the POWER button is turned OFF, press the VOL+ button on the projection display and the L button on the remote control simultaneously for more than 5 seconds. The cooling fan will operate for approximately 10 minutes. The LAMP indicator will flash red 5 times every 5 seconds.

4. Using a screwdriver, loosen the lamp unit screw. Grasp the lamp unit handle and slowly pull the lamp unit from the projection display.

Lamp Unit

Lamp Unit Screw 5. Insert the new lamp unit, paying attention to the direction of insertion. Press on the lamp unit handle, ensuring that the insertion is done correctly. Dispose of lamp in accordance with local environmental regulations. Tighten the lamp unit screw with using a screwdriver. [Note: Ensure that the lamp unit and lamp unit housing doors are attached securely. If not, the protective circuit will be activated and the power will not turn on.]

2. Grasp both sides of the front cover with your fingertips and pull it from the projection display for removal.

Lock/Open Knob

Lamp Cover

Lock/Open Knob

6. Close the lamp cover. Turn the Lock/Open knob to the right (clockwise).

Lamp Cover

3. Turn the Lock/Open knob to the left (counterclockwise). Pull the lamp cover out and down to open it. 7. Replace the front cover.

RESETTING THE LAMP TIMER

MODELS PT-44LCX65 / PT-52LCX65 / PT-61LCX65 / PT-52LCX15 WARNING: Only reset the lamp timer when the lamp has been replaced. 1. Plug the power cord back into a properly grounded wall outlet. Then press the POWER button on the projection display or the remote control to turn the power on.

UNIT

REMOTE CONTROL

SPLIT DVD/VCR CH

LAMP TIME WAS RESET TO 0.

L

- VOL+

2. While pressing the VOL- button on the projection display, hold down the SPLIT button on the remote control at the same time for more than 5 seconds.

v

p. 2

L

3. When the lamp time reset procedure is complete, the above screen will appear. (This screen may be different from the actual screen.) Note: When the lamp time reset is complete, the LAMP indicator goes out.

Information

instructions Pan combo (Page 2)

2 pages

Find more like this

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

195647


You might also be interested in

BETA
KDS-Z60/70XBR5
instructions Pan combo (Page 2)
EPSON EMP-83/822/X5/S5 User's Guide
06b_E70 Head-up Display
EX31 / EX51 / EX71 Multimedia Projector - User's Guide