Read h01.indd text version

Date: 2500

PRINCE SECTIONAL DIRECTIONAL CONTROL VALVES

SPECIFICATIONS: Model SV Parallel or Series Circuit Construction Pressure Rating: Maximum Operation Pressure 3000 PSI Maximum Tank Pressure 500 PSI Nominal Flow Rating 12 GPM Refer to Pressure Drop Curves Maximum Operating Temperature 180º Foot Mounting Weight Per Section Inlet Section Approx. 3.75 lbs. Outlet Section Approx. 3.75 lbs. Work Section (Standard) Approx. 5.50 lbs. Work Section (High) Approx. 8.00 lbs. Filtration: Fluid cleanliness should meet the ISO 4406 17/14 level. As a minimum, 10 micron filtration is recommended. SVI15 Inlet

H1

SVE11 Outlet

SVW1BA1 Work Section

Part Number

Our Sequence Number

Per Each

INLET SECTIONS All have both top and side inlet ports No relief - Port size #10 SAE ORB (7/8-14 Thread) Adjustable low pressure relief set at 1000 PSI - Port size #10 SAE ORB (7/8-14 Thread) Adjustable high pressure relief set at 2000 PSI - Port size #8 SAE ORB (3/4-16 Thread) Adjustable high pressure relief set at 2000 PSI - Port size #10 SAE ORB (7/8-14 Thread) WORK SECTION All have #8 SAE ORB (3/4-16 thd) ports, load check and standard lever handle 3-Way 4-Way 4-Way 4-Way 4-Way 4-Way 4-Way 4-Way Single Acting w/ Spring Center Double Acting w/ Spring Center (Work Ports Blocked in Neutral) Double Acting w/ 3 Position Detent (Work Ports Blocked in Neutral) Motor Spool w/ Spring Center (Work Ports Open to Tank in Neutral) Motor Spool w/ 3 Position Detent (Work Ports Open to Tank in Neutral 4 Postion Float w/ Spring Center and Float Detent Spool w/ Spring Center (with Pilot Operated Checks on Both Work Ports) Meter Spool w/ Sping Center (Work Ports Blocked in Neutral) SVW1AA1 SVW1BA1 SVW1BB1 SVW1CA1 SVW1CB1 SVW1DD1 SVL1CA1 SVM1ES1 SVE11 SVE21 SVE22 SVE23 SVE26 SVE27 660401001 660401002 660401003 660401004 660401005 660401006 660401007 660401008 660401009 660401010 660180001 660180002 660180003 660180051 660180011 660180032 660180005 660180031 660580001 660580002 660580003 660580004 660250006 660250003 660250002 200400030 660280001 660280002 1-800-228-9222 www.baumhydraulics.com 178210 178212 178214 178216 178218 178220 178222 178224 178226 178228 178230 178232 178234 178236 178238 178240 178242 178244 178246 178248 178250 178252 178254 178256 178258 178260 178262 178264 178266 178268 178270 178272 178274 178276 178278 178280 178282 178284 178286 178288 178290 178292 117.80 116.30 137.89 121.89 143.47 155.07 220.79 131.93 53.43 53.43 64.49 62.23 94.61 99.55 20.52 21.40 22.19 23.39 23.94 27.05 28.32 30.01 30.78 34.92 32.85 66.02 66.02 83.68 17.66 13.05 34.21 8.91 9.86 10.34 10.02 3.66 24.82 59.02 59.02 6.68 35.96 24.18 SVI21 SVI24 SVI15 SVI25 178202 178204 178206 178208 $63.52 85.64 85.64 85.64

OUTLET SECTION All have both top and side outlet ports Open Center Outlet w/ Conversion Plug - Port size #8 SAE ORB (3/4-16 Thread) Open Center Outlet w/ Conversion Plug - Port size #10 SAE ORB (7/8-14 Thread) Power Beyond Outlet w/ #8 SAE Beyond Port - Port size #10 SAE ORB (7/8-14 Thread) Closed Center Outlet - Port size #10 SAE ORB (7/8-14 Thread) Open Center Outlet Pressure Build-up Valve - Port size #10 SAE ORB (7/8-14 Thread) Power Beyond Pressure Build-up Valve - Port size #10 SAE ORB (7/8-14 Thread) TIE ROD KITS (Torque 150 in-lbs+ 6 in-lbs or 12-1/2 ft-lbs + 1/2) One Work Section Two Work Sections Three Work Sections Four Work Sections Five Work Sections Six Work Sections Seven Work Sections Eight Work Sections Nine Work Sections Ten Work Sections SPOOL ATTACHMENT KITS Spring Center Kit 3 Position Detent Kit Friction Detent Kit Float Detent kit HANDLE KITS Standard Handle Kit Clevis Sub-Assembly Complete Handle Kit Pin Kit SEAL KITS SVW/SVM Replacement Seal Kit Inlet Seal Kit Outlet Seal Kit Between Section Seal Kit INLET RELIEFS Inlet Relief Plug Low Pressure Inlet Relief High Pressure Inlet Relief OUTLET CARTRIDGES Open Center Plug #8 SAE Power Beyond Cart Closed Center Plug © 2011 by Baum Hydraulics Corporation

Prices subject to change without notice

H2

CROSS MOTOR CONTROL VALVES

With Free-Wheeling for Motors Motor will not hold a load when valve is in neutral Double-Acting 4-Way Valves Cross BA15BG3EAO

PRINCE "KNOCK-OUT" VALVES LS Series Hydraulic Directional Control Valve MEDIUM 25 GALLONS

Date: 2500

LS3000-2 One Spool Double-Acting USE-To start, stop and reverse a hydraulic motor. Valves have freewheeling which allows motor to coast to a stop when valve is returned to neutral. Valve is double-acting 4-way with forward, stop and reverse positions. Cross SPXTE-DF4 has 1/2" motor ports; 3/4" inlet and 3/4" end outlet. In neutral, all ports are open to tank; thus, a motor will "free wheel". (No hold position). If an operator has a motor running and instantly shifts the valve to reverse the motor (without letting it stop first) the load check in this valve will try to stop the motor instantly. When a standard control valve is returned to neutral to stop or start a motor, sudden excess pressure is created which will break seals, tear off motor shafts, burst motor cases, or burst hoses. This sudden shock cannot be relieved through the primary relief valve in the system. These valves with FREE-WHEELING eliminate this sudden shock and this damage to the motor. Detents allow control handle to remain in any selected position until shifted.

Part Number Cap. Wt. Gallon Lbs. Our Sequence Number Per Each

BA15BG3EAO

Cross Motor Control Valves Double-Acting 30 13

172800

$276.73

* See page H4 for Kits - one kit required for each valve

IMPORTANT FOR MOTORS

Use BA15BG3EAO Valve with FREE FLOW CENTER and DETENTS. Motors must use valve with free flow center which allows motor to free-wheel to stop when valve is put in neutral. This avoids sudden stops which break seals, tear off shafts, or burst motor cases, which may occur if standard valve is used. DETENTS allow control lever to remain in any selected position until shifted. These detents replace spring loaded feature in standard valve which springs control lever to neutral when not in use. For motors that must hold a load - such as a winch application, you can not use a free-wheeling valve. You must use a standard valve and a cushion valve to control the shock load. In some cases you may find it necessary to put a gear reduction between the motor and the load to prevent the load from running away. A 20 to 1 gear reduction is essentially a brake.

SPECIFICATIONS Capacity - 25 Gallons Maximum Pressure - 2750 PSI Relief Setting - 2250 PSI Pressure Relief Detent Setting - 600 to 2000 PSI Inlet & Outlet Ports - 3/4 inch Pipe Thread Cylinder Ports - 3/4 inch Pipe Thread Three 11/32 inch Mounting Holes in Base FEATURES * Pressure-operated detent (knock-out) is externally adjustable for pressures of 600 to 2000 PSI. * Pressure detent holds spool in one power position with spring centered to neutral. * For use with system flows up to 25 GPM. * Excellent spool metering provided by cast-in metering slots. * Built-in system relief valve on open center type. * Detent Release Pressure set at 1200 PSI. * Relief valve adjustable up to 2750 PSI. * Tandem center spool (in neutral position, both work ports blocked, pump unloaded to tank). * Ideal for log splitter applications. 3/4" NPTF work ports for higher flow applications. * Exceptional low pressure drop from pump to tank ports (open-center). The LS series directional control valve is a four way/three position valve that features a pressure release detent with spring return to neutral after cylinder or motor reaches preset pressure. Three mounting feet provide easy, "no-warp" mounting in any position. For added ruggedness and reliability the pressure detent release feature has been incorporated directly into the valve body casting. Provides heavy-duty service at an economical price. OPEN CENTER TYPE For use as a Knock-out Valve Special control valve with pressure operated detent valve spool stays in position until cylinder reaches end of stroke, then valve returns to neutral automatically.

Part Number Cap. Gallon Wt. Lbs. Our Sequence Number Per Each

LS3000-2

Double-Acting

25

--

178448

$149.27

Kick Out Control Valve Closed Center - No Relief

SPECIFICATIONS Maximum Pressure -3000 PSI Inlet & Outlet Ports - 3/4 inch Pipe Thread Work Ports - 1/2 inch Pipe Thread

Part Number Cap. Gallon Wt. Lbs. Our Sequence Number Per Each

Hydraulic circuit with one double-acting cylinder, using a doubleacting control valve, showing location of relief valve.

LS755C4JSHA

Double Acting 18

5.5

176010

$276.91

Power Beyond valves are used in these situations: 1) When adding an extra valve to an existing system. The new valve must be a power beyond valve and must be put between the pump and the existing valve. 2) When more than 3 spools are needed in a new system. This requires more than one valve, the valve nearest the pump must be a power beyond valve. 3) When pressure is required in more than one spool at a time. Standard valves are parallel operation, and when two spools are used at once, the one with the least pressure will act first and the one with more pressure will act second, like an auto with one wheel on the ice. When it is desired to operate two or three motors or cylinders or a motor and a Power Beyond Valve on Left Between cylinder together, separate valves must be used for each function, and Pump and Other Valve. all but the last valve next to the return line must be power beyond valves. When two or more valves are used in a multiple installation, all but In the diagram below, the valve on the left side next to the pump is a the last valve on the right side must be of the "Power Beyond" type to power beyond valve. This power beyond valve has one end outlet with a avoid breaking the valve casting. hex-bushing in it which connects to the inlet of the next valve. The other Standard Valve on Right Between end outlet has no bushing in it and must be connected to the tank. The Power Beyond Valve and Tank. other valve on the right side is a standard valve. © 2011 by Baum Hydraulics Corporation 1-800-228-9222 www.baumhydraulics.com Prices subject to change without notice

HOW TO USE POWER BEYOND VALVES

Date: 2500

ECONOMY SMALL HYDRAULIC CONTROL VALVES

H3

Parallel Application--Spool requiring lowest pressure will operate first when both handles are pulled at the same time. Motors must use valve with free-flow center which allows motor to freewheel to stop when valve is put in neutral. This avoids sudden stops which break seals, tear off shaft, or burst motor case-which may occur if standard valve is used. CROSS BA VALVE Equipment with separate loadcheck valves on each spool - assuring positive no drop control. Loads cannot be dropped as their direction is changed. Positive cylinder movement is always maintained; and no momentary reversal of the cylinder is possible as the spool is shifted, even if two handles are used at once.

Available with 3-way (single-acting) spools or 4-way (double-acting) spools or a combination of each. Has open center construction which allows unrestricted flow of oil from pump thru valve to tank when valve is in neutral position. Valve has three positions: lift, hold and lower. These are fully balanced plunger-type hydraulic units and are truly effortless to operate even at pressures of 1500 PSI. When the control lever is released, it automatically returns to a neutral or hold position. When valve is in neutral, oil returns to tank thru open center. All spools can be operated at the same time in parallel.

CONVERTA

CONVERSION

Included in the CV package is a 3-way cylinder port plug and a 3-way conversion plug. To convert from the basic 4-way (double-acting) to a 3-way (single-acting): 1. Insert the cylinder port plug (# 2AO349-8) into cylinder port "A" (port nearest the handle). 2. Remove the conversion plug, (# 1VO277) which is the hex nut located adjacent to the outlet port. 3. Insert the 3-way conversion plug (#2A0354-108) The valve is now converted for use with a single-acting cylinder or uni-directional motor. NOTE: Save the 4-way conversion plug for later reconverting back to 4-way operation.

DETENT KIT

To change from the standard spring centered version to a 3-position detent, order kit # 1VO294. Convert as follows: 1. Remover end cap 3. Install detent kit 2. Remover spring centering mechanism 4. Replace end cap The valve is now converted from spring centered to 3-position detent.

4-Way 3 position, spring centering easily coverts to: 4-Way 3 position detent 3-Way 3 position, spring centering 3-Way 3 position detent Now with one valve you have 4-way control for doubleacting cylinders or by converting back you have a 3-way control valve for single acting cylinders

WILLIAMS

1 Spool For Double Acting Cylinders

9 GPM 4500 PSI Max. Pressure Relief Set at 2500 PSI 3/8" Ports Weight 9 Lbs.

Part Number Seq. Number Per Each

PRINCE RD

1 Spool PRINCE RD

25 GPM 3000 PSI Max. Pressure Adjustable Relief 3/4" Inlet & Outlet 1/2" Cylinder Ports Three 3/8" Mounting Holes Weight 2 Spool 23 Lbs.

Part Number Our Sequence Number

RD & BA FEATURES

With Conversion Plug and End Tank Outlet NO Top Tank Outlet Built-In Adjustable Relief Valve Control Handle Reversible

Per Each | | Part Number

2 Spool PRINCE RD

25 GPM 3000 PSI Max. Pressure Adjustable Relief 3/4" Inlet & Outlet 3/4" Cylinder Opening Three 3/8" Mounting Holes Weight 2 Spool 21 Lbs.

CROSS BA

3 Spool

23THXSR 1314 (Repair Kit) CROSS CONVERTA

25GPM 2000 PSI Max. Pressure Built-In Relief Valve 3/4" Inlet & Outlet Ports 1/2" Cylinder Ports Weight 9 Lbs.

177728 177795

$213.48 57.81

CROSS BA

30 GPM 2000 PSI Max. Pressure Relief Set at 1500 PSI 3/4" Inlet & Outlet 1/2" Cylinder Ports Three 3/8" Mounting Holes Weight-1 Spool 9 Lbs. 2 Spool 17 Lbs.

Our Sequence Number Per Each

Our Sequence Number

Per Each

| |

Part Number

RD512CA5A4B1 -----

178445

ONE SPOOL VALVE, DOUBLE-ACTING--SELF-CENTERING TYPE | | CONVERTA $197.65 | RD513CA5A4B1 178460 $218.59 | BA11AG3EAO ONE SPOOL VALVE, SINGLE-ACTING--SELF-CENTERING TYPE .... | .... | CONVERTA

172805 172798 172805

$152.62 205.61 152.62

RD512CA5A4B1 w/ 660150002

ONE SPOOL VALVE, DOUBLE-ACTING With DETENTS | RD513CA5A4B1 w/ 660150002 | BA11AG3EAO w/ 1V0294 ONE SPOOL VALVE, DOUBLE-ACTING With DETENT, FREE-WHEELING .... | BA15BG3EAO ONE SPOOL VALVE, DOUBLE-ACTING, FREE-WHEELING | .... | BA15AG3EAO 172800 172801 173058 173078 276.73 236.94 312.80 414.14

RD522CCAA5A4B1 RD532CCCAAA5A4B1

178446 178447

TWO SPOOL VALVE, BOTH DOUBLE-ACTING 315.29 | RD523CCAA5A4B1 178461 310.78 | 447.81 | THREE SPOOL VALVE, ALL DOUBLE-ACTING RD533CCCAAA5A4B1 178462 447.81 |

BA211AAG3EAO BA3111AAAG3EAO

NOTE: The Prince RD and Cross BA valves have load checks. The Cross Converta and Williams valves does not have a load check needed when lifting heavy loads. Closed center plug and relief plug are NOT included, order seperately.

CLOSED CENTER CONVERSION PLUGS

for Cross BA Valves ONLY Closed center plug for converting Cross valves with conversion plug to closed center type valve for use on closed center hydraulic system. This plug changes the valve to a closed center valve. This MUST only be used with Closed Center type systems or pump will be ruined. Relief valve in control valve must be removed and NO relief plug installed.

Closed Center Cross BA Our Sequence Number Per Each

Closed Center Plug

Do Not Use Prince Monoblock Valves on Closed center System

Closed Center Plug No Relief Plug © 2011 by Baum Hydraulics Corporation

1V0206 1R0035

726592 726500

$36.13 20.81 Prices subject to change without notice

1-800-228-9222 www.baumhydraulics.com

H4

FLOAT POSITION PRINCE & CROSS MEDIUM HYDRAULIC CONTROL VALVES CROSS PRINCE METRO

Standard One Spool Standard Two Spool Standard Three Spool With Float on First Spool Two Spool and Three Spool All Double Acting with 4 Position Float on the First Spool 6 GPM Relief 2000 Standard Two Spool All Ports 9/16-18 o-ring

Date: 2500

NOTE: PRINCE RD AND CROSS BA Valves are now stocked with the adjustable relief valves set to operate at 2000 PSI. USE--Float position valve is indispensable on haybucks, bulldozers and snowplows. This valve provides a passage of oil from end to end of the doubleacting cylinder allowing a haybuck, loader, snowplow or dozer blade to ride the contour of uneven ground as the machine moves forward. This float valve has four positions. The first three are lift, hold and lower, and are standard open center, spring return to neutral or hold position. The fourth handle position is equipped with a detent which holds handle in float operating position for operation of float. Control lever remains in this float position until operator moves it. The second control in the double valve may be either 3-way for use with single-acting cylinders or 4-way for use with double-acting cylinders. This standard control is open center with spring return to neutral. PRINCE RD

Description Control Valve Number Our Sequence Number Per Each | Part | Number

CROSS BA

Our Sequence Number Per Each | Part | Number

METRO D2

Our Sequence Per Number Each

One spool valve double-acting RD513GG5A4B1 with built-in float Two spool valve one RD523GCGA5A4B1 double-acting with built-in float & one double-acting

178454 $230.51 | - - - - | 178456 339.45 | BA2A1XAG3EAO |

$.... | - - - - |

$....

173888 356.54 | D2CF1T2J 704990 403.66 | .... 704992 21.60 704991 28.93

Three spool valve -one RD533GCCGAA5A4B1 178458 double-acting with built-in float & two double-acting

476.48 | BA3A11XAAG3EAO 173970 457.87 | - - - - | | | Power Beyond Sleeve for Metro | M-PB | Closed Center Plug for Metro | M-CC

Complete with all seals for converting Prince, or Cross valves with conversion plug to power beyond operation by removing conversion plug and inserting power beyond sleeve. Original end outlet must still be piped to tank. POWER BEYOND KITS For This sleeve is to be piped to inlet of an additional valve downPRINCE stream from this valve. The sleeve prevents subjecting the valve to CROSS back pressure. Detent Kits for Converting POWER BEYOND Prince and Cross SLEEVE ASSEMBLY Valves with Spring Centered Spools to 3-Position Detents. (NO SPRING CENTERING)

CLOSED CENTER KITS For PRINCE CROSS

CLOSED CENTER SLEEVE ASSEMBLY

DETENT KITS PRINCE

Parts and Kits For | | | SP/SPK/RD Valve Our Sequence Number Per Each | | | SP/SPK/BA Valve

CROSS

Our Sequence Number Per Each

Power Beyond Sleeve

|

|

660312004 660150002 660150003 660150018 ----660312005 660250006 660551001 660552001 660553001 660150004

178392 178382 178383 178385 178394 178282 EE2152 EE2154 EE2156 178384

$28.80 80.98 80.98 169.59 .... 29.75 24.82 2.53 2.83 3.32 16.23

|

|

1V0208 1V0294 1V0558 ----1V0559 1V0206 1R0035 2V0008 2V0009 2V0010 1V1703 Plus 1V1701 for BA 1V1702 for CA 1A0768 1A0744 1V1225 500-1500 PSI SP & SPK 1R0016

726656 727040 726976 727104 726592 726500 EE2112 EE2114 EE2116 727424 727488 727552 727770 726720 726715 728388

$23.24 49.14 82.72 .... 82.72 36.13 20.81 1.76 2.08 2.48 24.03 8.41 8.41 4.66 4.44 29.60 45.20 45.20

3-Position Detent Kit, No Spring | Friction Detent Kit | 1-Position Detent Kit OUT w/ spring cntr | 1-Position Detent Kit OUT |

|

| | | |

|

Closed Center Plug No Relief Plug Seal Kit for 1 Spool Valve Seal Kit for 2 Spool Valve Seal Kit for 3 Spool Valve Handle Assembly

| |

|

| |

|

| | |

|

| | |

|

| | |

| |

| | |

| |

Knob for Selector Valve Centering Spring (only) to Neutral Centering Spring Kit Low Pressure Relief Cartridge for SP High Pressure Relief Cartridge for SP

| | |

|

| 660150001 178380 37.15 | |

|

| |

|

500-1500 PSI SP & SPK 660250003 178284 -----

59.02 ....

| |

|

| |

| |

1500-3000 PSI SP & SPK 1R0017 726464

© 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

Date: 2500

PRINCE 8 GPM MONOBLOCK VALVES

H5

Product Features: 1-6 Spool monoblock 3500 PSI #8 O-ring in/out ports #8 Work ports Interchangeable motor spool Convertible to power beyond and closed center capability Double acting Load check Closed center Adjustable relief Enclosed handle

1 Spool 2 Spool 5 Spool

PRINCE 8 GPM VALVES

Part Number Our Sequence Number Per Each

Description

MB11B5CI MB11C5CI MB21BB5CI MB21GB5CI MB31BBB5CI MB41BBBB5CI MB52BBBBB5CI MB61BBBBBB5CI

178468 178470 178472 178474 178476 178478 178480 178482

$157.10 182.02 248.83 405.97 330.00 396.80 485.61 615.74

1 1 2 2 3 4 5 6

Spool Spool Spool Spool Spool Spool Spool Spool

Spring Center 8 GPM for Motor 3 position Detent 8 GPM Spring Center 8 GPM Float with Detent and Spring Center Spring Center 8 GPM Spring Center Spring Center 8 GPM Spring Center 8 GPM

PRINCE PARTS FOR 8 GPM VALVES

Part Number Our Sequence Number Per Each

Description

660170057 660170058 660170061 660270005 660270006 671900122

178296 178298 178300 178302 178304 178306

$18.45 54.89 284.46 67.06 26.81 5.57

Spring Center Kit for 8 GPM Valve Three Position Detent Kit for 8 GPM Valve Joystick for 8 GPM Valve Relief Valve 2000-3500 for 8 GPM Valve Relief Plug for 8 GPM Valve Power Beyond Plug for 8 GPM Valve

PRINCE CONTROL VALVES With Closed Center Plug Included

Economical monoblock construction of high tensile strength gray cast iron. Valves have a load check, a complete lever handle assembly, and an adjustable ball-spring relief set at 1500 PSI/12 GPM. Convertible from open center to closed center with included plug. Use with system flows to 20 GPM and pressures to 3000 PSI. Open Center to Closed Center Conversion

RD-2575

3-Position Detent Kit

Kits for ALL RD-2575 Series Valves

3/4 NPTF IN/OUT 1/2 NPTF WORK Part Number Our Sequence Number Per Each | | Kit Part Number Desctiption Our Sequence Number Per Each

4 way Tandem Center 3 way Tandem Center 4 way Motor Spool © 2011 by Baum Hydraulics

RD-2575-T4-ESA1 RD-2575-T3-ESA1 RD-2575-M4-ESA1 Corporation

178440 $140.25 | 660125001 178442 153.35 | 660125002 178444 146.16 | 660525001 1-800-228-9222 www.baumhydraulics.com

Detent Kit 178376 $43.75 Spring Center Kit 178378 11.45 Seal Kit 178379 10.74 Prices subject to change without notice

H6 Specifications:

MODEL LVT TWO SPOOL MONO-BLOCK LOADER VALVE

Date: 2500

Parallel Circuit Maximum Operating Pressure Maximum Tank Pressure Maximum Operating Temperature Recommended System Filtration Flow Rating Weight

3000 PSI 500 PSI 180° F ISO 4406 17/14 10 GPM 14.6 LBS.

Standard Features

Economical monoblock construction of high tensile strength gray cast iron. Load check on each spool Hard chrome plated spool Adjustable cartridge relief Open center, and power beyond available 4 position float spool for loader boom 4 position regen spool for loader bucket

5/16-18 UNC MOUNTING HOLES ON BOTH TOP AND BOTTOM OF VALVE NOTE: NEUTRAL POSITION SPOOL LOCK AVAILABLE

MODEL LVR TWO SPOOL MONO-BLOCK LOADER VALVE Specifications:

Parallel Circuit Maximum Operating Pressure Maximum Tank Pressure Maximum Operating Temperature Recommended System Filtration Flow Rating Weight 3000 PSI 500 PSI 180° F ISO 4406 17/14 14 GPM 22.6 LBS.

Standard Features

Economical monoblock construction of high tensile strength gray cast iron. Load check on each spool Hard chrome plated spool Adjustable cartridge relief Open center, and power beyond available 4 position float spool for loader boom 4 position regen spool for loader bucket

5/16-18 UNC MOUNTING HOLES ON BOTH TOP AND BOTTOM OF VALVE NOTE: NEUTRAL POSITION SPOOL LOCK AVAILABLE

4 Way 4 Position Regen Spool Operation

This spool option allows for these four functions of the loader bucket cylinders: "Neutral", cylinder ports blocked to hold bucket in place; "Bucket Rollback" directs oil to hose 1 to retract bucket cylinder; "Bucket Tip" directs oil to hose 2 to extend the bucket cylinder with full pressure (Please Note: there is a soft stop at this handle position); "Bucket Regen" combines the oil from the tractor pump with the oil returning from hose 1 and it directs it to hose 2 to tip the bucket faster (referred to as Regeneration or "Regen"). It is necessary to push the handle past the soft stop at the normal bucket tip position to get to the regen position. Also Please note the the cylinder force will be reduced when in the regen position.

4 Way 4 Position Float Spool Operation

This spool option allows for these for functions of the loader boom cylinders: "Neutral", cylinder ports blocked to hold boom in place; "Boom Raise" directs oil to hose 3 to extend boom cylinders; "Boom Lower" directs oil to hose 4 to retract the boom cylinders with full pressure (Please not there is a soft stop at this handle position); "Boom Float? connects all boom cylinder ports to tank allowing the boom to fall to the ground. It is necessary to push the handle past the soft stop at the normal boom down position. These is a detent that will hold handle in the float position. While in the float position the loader boom cylinders will move up and down or "Float" to match the ground level as the tractor moves forward or backward.

Joystick Handle

The joystick handle will operate both spools using one lever handle. The two spools can be operated independently or at the same time depending upon handle movement. Because we allow for maximum mounting flexibility, we have 4 options for the LVT, 2 options for the LVS and 4 options for the LVR. The handle shift pattern for all is shown at the right.

Joystick Handle Operation Looking at Handle Knob

Part Number

Our Sequence Number

Per Each

LVR1GR5AB7 LVT1GR5AB7

178449 178450

$530.39 458.12 1-800-228-9222 www.baumhydraulics.com Prices subject to change without notice

© 2011 by Baum Hydraulics Corporation

Date: 2500

PRINCE SECTIONAL DIRECTIONAL CONTROL VALVES

Model 20 SPECIFICATIONS: Parallel or Tandam Circuit Construction Pressure Rating: Maximum Operation Pressure 3500 PSI Maximum Tank Pressure 500 PSI Nominal Flow Rating 20 GPM Refer to Pressure Drop Curves Maximum Operating Temperature 180º Foot Mounting Weight Per Section Inlet Section Approx. 6.0 lbs. Outlet Section Approx. 3.5 lbs. Work Section (Standard) Approx. 9.0 lbs. Filtration: Fluid cleanliness should meet the ISO 4406 17/14 level. As a minimum, 10 micron filtration is recommended.

H7

SERIES 20

INLET SECTIONS All have both top and side inlet ports No relief - Port size 1-1/16 O Ring Ports Adjustable low pressure relief set at 1750 PSI - Port size 1-1/16 O Ring Ports Adjustable high pressure relief set at 2200 PSI - Port size 1-1/16 O Ring Ports Adjustable high pressure relief set at 2500 PSI - Port size 1-1/16 O Ring Ports WORK SECTION All have 7/8 oring ports, load check and standard lever handle 3-Way Single Acting w/ Spring Center 4-Way Double Acting w/ Spring Center (Work Ports Blocked in Neutral) 4-Way Double Acting w/ 3 Position Detent (Work Ports Blocked in Neutral) 4-Way Motor Spool w/ Spring Center (Work Ports Open to Tank in Neutral) 4-Way Motor Spool w/ 3 Position Detent (Work Ports Open to Tank in Neutral 4-Way 4 Postion Float w/ Spring Center and Float Detent 4-Way Spool w/ Spring Center (with Pilot Operated Checks on Both Work Ports) OUTLET SECTION All have both top and side outlet ports Open Center Outlet w/ Conversion Plug - Port size 1-1/16 O Ring Ports Power Beyond Outlet w/ #10 SAE Beyond Port - Port size 1-1/16 O Ring Ports Closed Center Outlet - Port size 1-1/16 O Ring Ports TIE ROD KITS (Torque 360 inch pounds or 30 - 32 foot-pounds) One Work Section Two Work Sections Three Work Sections Four Work Sections Five Work Sections Six Work Sections Seven Work Sections Eight Work Sections Nine Work Sections Ten Work Sections SPOOL ATTACHMENT KITS Spring Center Kit 3 Position Detent Kit Friction Detent Kit HANDLE KITS Standard Handle Kit Complete Handle Kit SEAL KITS Inlet Seal Kit Outlet Seal Kit Between Section Seal Kit INLET RELIEFS No Relief Plug Low Pressure Inlet Relief - Set at 1750 PSI High Pressure Inlet Relief - Set at 2500 PSI OUTLET CARTRIDGES Open Center Plug Power Beyond Cart with 7/8 oring port Closed Center Plug © 2011 by Baum Hydraulics Corporation 1-800-228-9222 www.baumhydraulics.com

Part Number

Our Sequence Number

Per Each

20I2A 20I2G 20I2H 20I2J

178201 17820102 17820104 17820106

$119.85 174.40 174.40 174.40

20P1AA1AA 20P1BA1AA 20P1BB1AA 20P1CA1AA 20P1CB1AA 20P1DD1DD 20L1CA1

17820108 17820110 17820112 17820114 17820116 17820118 17820120

233.19 222.35 230.88 233.57 241.73 417.42 318.67

20E21 20E22 20E23

17820122 17820126 17820128

78.07 90.74 86.82

660402001 660402002 660402003 660402004 660402005 660402006 660402007 660402008 660402009 660402010

178237 17823702 17823704 17823706 17823708 17823710 17823712 17823714 17823716 17823718

26.33 29.35 31.02 34.21 42.16 44.78 49.32 56.48 62.05 75.01

660190003 660190004 660190005

17823720 17823722 17823724

34.68 47.09 47.09

660190002 660190007

17823728 17823730

40.17 44.78

660585002 660585003 660585004

17823732 17823734 17823736

10.10 10.34 10.02

660290001 660290203 660290207

17823750 17823740 17823742

23.55 118.37 118.37

660290006 660290004 660290005

17823744 17823746 17823748

12.09 28.08 25.30

Prices subject to change without notice

H8

COMMERCIAL SECTIONAL DIRECTIONAL CONTROL VALVES

SOLD IN INDIVIDUAL SECTIONS, BOLT & HANDLES SOLD SEPARATELY ORDER RELIEF VALVE SEPARATELY

Date: 1700

MEDIUM SIZE DVA20 VALVES 30 Gallon Capacity 2500 PSI 1-5/16" O-Ring B Top Inlet Port And 1-5/16" O-Ring End Inlet Port 1-5/16" O-Ring Top Outlet Port 1-1/16" O-Ring Cylinder Port 1-5/16" O-Ring End Power Beyond Port

LARGE SIZES DVA35 VALVE 50 Gallon Capacity 2500 PSI 1-5/16" O-Ring B Top Inlet Port And 1-5/8" O-Ring B End Inlet Port 1-5/8" O-Ring Outlet Port 1-5/16" Cylinder Port 1-5/8" O-Ring End Power Beyond Port

Valves have SEPARATE TRANSITION CHECKS built into each spool for positive control. Positive cylinder movement is maintained. Valves not exactly as pictured.

30 Gallon Valve Part Number Our Sequence Number SECTION Per Each | | | | Part Number 50 Gallon Valve Our Sequence Number SECTION Per Each

INLET COVER LEFT SIDE WITHOUT RELIEF VALVE Must order Relief Valve Cartridge Cover Plate with end and top inlet - NO outlet DVA20-A880 JL0010 CENTER SECTION - LO-BOY With Double-Acting Spool 4-way With Single-Acting Spool 3-way With Double-Acting Spool & Float 4-way With Double-Acting Spool, Detents & Free Wheeling for Motors With Double-Acting Spool, Spring Return Free Wheeling for Motors With Double Acting Spool, 4-way, 12 Volt With Double Acting Spool, 4-way, Airshift CENTER SECTION - HI-BOY With Double Acting Spool, 4-way With Single Acting Spool, 3-way With Double Acting Spool & Float, 4-way With Double-Acting Spool, Spring Return & Free Wheeling for Motors With Double Acting Spool, 4-way, 12 Volt With Double Acting Spool, 4-way, Airshift MID-INLET CONVERSION SECTIONS With Top Inlet, Comb. Flow With Top Inlet, Split Flow OUTLET COVER RIGHT SIDE Cover plate for Power Beyond or Closed Center Cover plate with end & top outlet for Open Center ONLY HANDLE ASSEMBLY Order 1 for each spool For DVA Section 10" DVA20-DA7 DVA20-SA7 DVA20-FC7 DVA20-MB7 DVA20-DK7* DVA20-DV7 DVA20-HA755 DVA20-JA705 DVA20-LA755 DVA20-HK755* DVA20-HV755 DVA20-CFA70 DVA20-SFA70 DVA20-PB80 DVA20-TR88 DV20-H-6 DV20-H-10 JL0020 JL0030 JL0040 JL0050 JL0060 JL0070 JL0080 JL0090 JL0100 JL0110 JL0120 JL0130 JL0140 JL0150 JL0160 JL6000 JL6004

| $137.80 | 252.51 252.24 454.41 306.24 419.27 527.61 | | | | | | | | | |

DVA35-A980 DVA35-DA8 DVA35-SA8

JL0732 JL0740 JL0750

$203.87 381.81 379.95

DVA35-MA8 DVA35-DK8* DVA35-DV8 DVA35-HA855 DVA35-JA805 DVA35-GC855 DVA35-LA855 DVA35-HK855* DVA35-HV855 DVA35-CFA80 DVA35-SFA80 DVA35-PB90 DVA35-TR99 DV35-H-6 DV35-H-10

JL0760 JL0770 JL0780 JL0790 JL0800 JL0810 JL0820 JL0830 JL0840 JL0850 JL0860 JL0870 JL0880 JL7000 JL7004 JL5320 JL5340 JL5360 JL5380 JL5400 JL5420 JL5440 JL5460 JL6182 JL6184 JL6180 JL6185 JL7178 JL7180 JL7181 JL71815 JL62025 JL0890 JL0900 JL7240 JL7260 JL7280 JL7300 JL7320

397.56 515.93 576.74 389.44 389.44 546.08 406.50 541.72 600.95 212.68 243.41 146.86 142.37 52.98 52.72 23.24 31.39 46.81 55.90 67.15 73.92 80.55 169.40 80.03 80.03 134.06 24.22 12.41 30.06 17.90 32.63 18.07 32.63 127.29 67.86 48.09 253.44 176.49 772.38

| 305.68 | 275.24 | | | 305.68 | 879.27 | 583.20 | | 189.48 | 189.48 | | 118.50 | 83.64 | | 46.74 | 47.21 |

THROUGH BOLT KITS COVER PLATES DO NOT COUNT AS SPOOLS TORQUE TO 20 FOOT LBS.--NO MORE For 1 Spool Valves (NOTE: Bolts DVA20-SK-1 JL5000 12.27 | DVA35-SK-1 For 2 Spool Valves Priced Per Set) DVA20-SK-2 JL5020 14.77 | DVA35-SK-2 For 3 Spool Valves DVA20-SK-3 JL5040 21.10 | DVA35-SK-3 For 4 Spool Valves DVA20-SK-4 JL5060 37.25 | DVA35-SK-4 For 5 Spool Valves DVA20-SK-5 JL5080 40.32 | DVA35-SK-5 For 6 Spool Valves DVA20-SK-6 JL5100 43.65 | DVA35-SK-6 For 7 Spool Valves DVA20-SK-7 JL5120 50.39 | DVA35-SK-7 For 8 Spool Valves DVA20-SK-8 JL5140 61.96 | DVA35-SK-8 Slug Adj. 1000 PSI Relief without A/C 500-1000 PSI Slug Adj. 2000 PSI Relief without A/C 1000-2500 PSI 2500 PSI Comb. Relief with Anti-Cavitation 500-5000 Work Port Relief Plug for Hi-Boy Valves DV-PRV-1 DV-PRV-2 DV-PRVAC DV-PRVP JL6182 JL6184 JL6180 JL6185 JL6190 JL6200 JL6201 JL62015 JL62025 JL0170 JL0180 JL6240 JL6260 JL6280 JL7422 JL6320 80.03 80.03 134.06 24.22 12.41 27.34 17.90 40.14 18.07 32.63 102.11 50.91 41.49 235.13 280.36 772.38 | | | | | | | | | | | | | | | | DV-PRV-1 DV-PRV-2 DV-PRVAC DV-PRVP DV35-K-11 DV35-K-12 DV35-K-3 DV35-K-3-1 DV-K-7 DVA35-MRVP DVA35-MRV-2 DV35-K-201 DV35-K-200 DV35-K-202 DV35-K-213 DV35-K-206*

Seal kits - Sectional seals only DV20-K-1 Seal kits - Order 1 each spool with sectional seals DV20-K-2 Seal kit for DVA Port Relief Valve without A/C DV20-K-3 Seal kit for DVA Port Relief Valve with A/C DV20-K-3-1 Seal kit for DVA20 & DVA35 Air Shift DV-K-7 Relief Plug required for Closed Center Valves DVA20-MRVP Adj. Main Relief Cart. for Power Beyond & Open Center Valves DVA20-MRV Detent kit 3-Position DV20-K-101 Spring Return DV20-K-100 Rotary Control Actuators DV20-K-102 Airshift Actuators DV20-K-113 Solenoid Actuators 12 Volt DC DV20-K-106* *SOLENOID SECTION and INLET NEED PILOT SUPPLY MACHINING. © 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

Date: 2500

SOLD IN INDIVIDUAL SECTIONS, BOLT & HANDLES SOLD SEPARATELY ORDER RELIEF VALVE SET AT 2500 PSI V20LS VALVE 30 Gallon Capacity

GRESEN SECTIONAL DIRECTIONAL CONTROL VALVES

H9

V20 VALVE 30 GPM 3500 PSI With Top and Side Ports 1-1/16" O-Ring Inlet 1-1/16" O-Ring Outlet

Continuous Operating: 3000 PSI Rating at work port with valve spool in neutral: 5000 PSI Capacity: Normal : 20 GPM Maximum: 30 GPM Max Exhaust Core Pressure: With std spool seal retainer: 200 PSI Filtration Required : 33 micrometre

MODEL V20P LEFT INLET COVER for V20

(8072 Section) 20-10-03 20-10-04 20-10-DF4 20-10-K04-2000 20-10-K4

MJ2 Handle Assembly Outlet Cover w/ Bleed Port 30 Gal. V20 Valve

Part Number Our Sequence Number Per Each

Valves not exactly as pictured.

| | |

30 Gal. V20LS Valve

Part Number Our Sequence Number Per Each

INLET SECTION LEFT SIDE WITHOUT RELIEF VALVE Must order Relief Valve Cartridge Cover Plate with end and top inlet & outlet 20-LC-12 343320 $110.75 Cover Plate with built-in Flow Control 20-LC-12-FC 343326 537.25 Plug the Outlet in these Left Cover Plates if you use the Outlet in the Right Cover Plate. No Relief Plug Needed for Load Sense Inlet Cover ----.... CENTER SECTION With Double-Acting Spool 4-way 20-10-04 With Double-Acting Spool, 4-way, Big Ports 20-R12-04 With Single-Acting Spool 3-way 20-10-03 *Spring return to neutral, SAE 10 ports, 4-way, 20S-10-04 With Double-Acting Spool & Float, 4-way 20-10-K4 With Dble-Act Spool-Detent & Free Flow for motors 20-10-DF4 With Dble-Act Spool Spring Center & Free Flow for motors - - - - With Dble-Act Spool, 4-way with Pressure Detent 20-10-K04-2000 MID-INLET CONVERSION SECTION With Top Inlet and Split Flow With Top Inlet and Combined Flow OUTLET SECTION RIGHT SIDE Cover Plate w/Convers. Plug & End Outlet SHUTTLE VALVE For Load Sense Line - 6SAE Ports 20-12-SF 20-12-CF 20-RC-12-E-MY ----Y94432 Y94434 Y94436 Y94438 Y94440 Y94442 Y94444 Y94446 349237 361680 EE2330 361780 349009 361800 3475832 347583 361840 361740 361450 347477 347480 347500 347600 347620 347540 343350 343338 343370 343351 343390 343400 343396 343430 343420 343330 188.00 198.24 198.24 280.14 253.15 232.67 .... 397.41 120.41 106.53 80.04 .... 5.79 8.79 10.09 11.95 20.64 29.68 30.95 33.17 287.70 33.95 6.06 20.49 25.13 16.98 121.01 111.71 56.20 49.17 32.20 87.92 87.92 87.92 86.88 86.88 161.35

| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

20-LC-12 ----K-20-NR 20LS-10-04 ----20LS-10-03 ----20LS-10-K4 ----20LS-10-F4 ------------20-RC-12-E-LS LSV1-6T-N K-20LS-1 K-20LS-2 K-20LS-3 K-20LS-4 K-20LS-5 K-20LS-6 K-20LS-7 K-20LS-8 MJ2-20L K-20-VH-B

343320 349009 343404 343402 343406 343409

$110.75 .... 25.13 255.01 .... 255.01 .... 329.47 .... 279.21 .... .... ....

343410 342790 Y944325 Y944345 Y944365 Y944385 Y944405 Y944425 Y944445 Y944465 349237 361680

183.35 31.47 4.56 6.91 8.00 9.28 16.12 23.01 24.07 25.84 287.70 33.95

THROUGH BOLT KITS COVER PLATES DO NOT COUNT AS SPOOLS For 1 Spool Valves (NOTE: Bolts K-20-1 For 2 Spool Valves Priced Per Set) K-20-2 For 3 Spool Valves K-20-3 For 4 Spool Valves K-20-4 For 5 Spool Valves K-20-5 For 6 Spool Valves K-20-6 For 7 Spool Valves K-20-7 For 8 Spool Valves K-20-8 HANDLE ASSEMBLY Single Lever Acturator for 2 Functions Order 1 for each spool Seal Kits-Order 1 ea. spool w/sect. seals Closed Center Plug No Relief Plug Conversion Plug Cylinder Port Relief & Anti-Cavitation Cylinder Port Relief & Anti-Cavitation Power Beyond Sleeve 3-Position Detent Kit Spring Return Kit Main Relief Cartridge Main Relief Cartridge Main Relief Cartridge Work Port Relief Adjustable 1250-1749 PSI Work Port Relief Adjustable 1750-1999 PSI Adjustable Main Relief MJ2-20L K-20-VH-B K-6027A K-20-C K-20-NR K-20-X CRA-2550 CRA-2000 K-20-50-Y K-20-D K-6125 WH-1700 WH-1950 WH-2550 RC-1700 RC-1950 RP-51A-3000

2 or more Directional control valve assemblies may be supplied from a single variable displacement pump by using a T arrangement

*This section is a series section, for open center systems ONLY. © 2011 by Baum Hydraulics Corporation 1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

H10

BAUM SOLENOID CARTRIDGE VALVES

Utility On/Off Valves normally open or closed. LB10705A Does not have wiring nor switches. LB10573A

Date: 2500

40 PSI Minimum to Lift Poppet

MUST ORDER CARTRIDGE, COIL & BODY

Part Number Type GPM Description Our Sequence Number Per Each

GS041700NC GS040600NC GS061500N NO GS060600NC CCP012S CCP115C LB10705A LB10573A 255-955

Cartridge Cartridge Cartridge Cartridge Coil Coil Body Body Connector

18 18 50 50

Normally Normally Normally Normally

Open Cartridge for 10 series Closed Cartridge for 10 series Open Cartridge for 16 series Closed Cartridge for 16 series

or CCS115C for 115VAC 16 series add CCP012S 12VDC 10 & 16 series 10 & 16 series

350011 350013 350014 350015 3500204 3500185 350012 350017 000250

$119.87 124.12 288.55 246.64 43.49 77.44 71.08 118.81 0.00

12 Volt space connector coil for cartridge valve 115 Volt dbl. lead wire w/ conduit connector for cartridge valve Line Body SAE #8 Ports Line Body SAE #16 Ports Female DIN 43650 connector for CCP*** coil Small Large

SOLENOID CONTROL VALVES

4-WAY 12 VOLT SOLENOID VALVE SECTION MULTIPLE VALVES CAN BE USED BY ORDERING THE CORRECT MOUNTING BRACKET Date: 1700 No back pressure - 12 Volt Direct Solonoid Operator Maximum Operation PSI 3600 3 Position 4-way valves with neutral valves come with bolt kit and o-rings but not subplate.

MS06 Selector 12 Gallon

Part Number Description

MD06 Control Valve 20 Gallon

Our Sequence Number Per Each

Part Number

GPM

Our Sequence Number

Per Each

MD06-SDNC-AD-12B

4-way Single 12 volt with 3/4 o-ring ports

FREE WHEELING FOR MOTORS SSG03-C4-R-C115-E20 20 109622 SSG03-C4-R-D1-E 20 20 109618 SSG03-C5-R-D1-E 10 CLOSED CENTER 20 109619

$445.48 418.55 432.01

349425 VALVE 349430 349431 349432 349433 349434 349400 349465

$626.79 42.01 71.18 86.35 95.69 112.02 579.22 107.36

K-707871 K-707872 K-707873 K-707874 K-707875

MOUNTING BRACKETS FOR ABOVE For Single Valve Kit For Two Valve Kit For Three Valve Kit For Four Valve Kit For Five Valve Kit Double Selector 12 volt with 9/16 o-ring ports 12 Volt coil for MD & MS

TANDEM VALVE (Open Center - Cylinder Ports Blocked) SSG03-C7Y-R-D1-E 10 13 109624 406.21 SSG03-C7Y-R-D1-E 20 20 109625 406.21 SUBPLATE SIDE PORTS - 3500 PSI - ALUMINUM

Part Number Description Our Sequence Number Per Each

MS06-UDNA-12B 493419

A-D03-SPS-6S A-D05-SPS-8S

9/16-18 Side Ports SS-G01 3/4-16 Side Ports SS-G03

004002 004004

$63.72 98.17

MARKER VALVE FOR PLANTERS SEQUENCE VALVE

This is an excellent valve for operating planter markers. Both markers will raise together, but only one marker will drop. This process will alternate between markers.

Part Number PSI Rating Our Sequence Number Per Each

Ports

Weight

SQV © 2011 by Baum Hydraulics Corporation

3/4 O-ring

2500

6 lbs.

174000

$139.98

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

Date: 2500

FASSE VALVES 2 CIRCUIT SELECTOR

STANDARD 700-1510 KIT SHOWN

H11

SPOOL SELECTOR VALVE KIT REMOTE MASTER SERIES 700-1510 FEATURES: · Up to 20 GPM · Operate multiple functions from one remote outlet · Keep high pressure hydraulic lines & cables out of the cab · Double or single acting cylinder operation · Valve plugs directly into existing remote or may be mounted on implement · Both circuits can be selected at the same time, lightest load moves first · Universal, use on Open, Closed or PFC hydraulic systems · Up to 6 circuit control available · Easy installation · 3000 PSI rated

Less Cylinders

· · · · · · · · ·

Two Circuit Selector Valve Toggle Switch box with mounting bracket 12' wiring harness, 6' power wires Fasse eccentric fittings Fasse ISO quick couplers and tips Colored dust plugs and caps 12 volt negative ground coils Fuse kit, connectors, wire ties Installation and operation guide TYPICAL APPLICATIONS

Loader Bucket Marker Arms Left Bat Wing Mowers Right Wing Left Wing Round Balers End Gate Bale Tie Box Scrapers Height Angle

Grapple Right

3/4-16 O-Ring Ports 2 SPOOL VALVE WITH SWITCH

Part Number Our Sequence No. Per Each

700-1510

000202

$727.30

3 CIRCUIT SELECTOR

SPOOL SELECTOR VALVE KIT REMOTE MASTER SERIES 700-1553 FEATURES: · Up to 20 GPM · Double or single acting cylinder operation · Operate multiple functions from one remote outlet · Universal, use on Open, Closed or PFC hydraulic systems · Valve mounts on tractor or implement · Allows tractor float operation on selected circuits · Easy installation · 3000 PSI rated STANDARD 700-1553 KIT SHOWN · Three Circuit Selector Valve · Remote command stick control · 12' wiring harness, 6' power wires · Fasse ISO quick couplers and tips · Colored dust plugs and caps · 12 volt negative ground coils · Fuse kit, connectors, wire ties · Installation and operation guide OPTIONS · 12 volt positive ground coils · 24 volt negative ground coils · John Deere or IH couplers TYPICAL APPLICATIONS

Loader Boom Bucket Planter Tool Bar Left Marker Lift Assist Bat Wing Mowers Blade Tilt Angle Raise/ Lower

Left Wing Right Fold Wing Lift Assist Raise/ Lower

Grapple Right Marker

Right Left Wing Fold Wing

Less Cylinders

3/4-16 O-Ring Ports 3 SPOOL VALVE WITH JOYSTICK

Part Number Our Sequence No. Per Each

JOYSTICK FOR 2 or 3 SPOOL VALVE

Part No. Our Sequence No. Per Each

700-1553

000204

$1447.67

300-081

000220

$487.00

UTILITY ON/OFF CONTROL KIT

3/4" O-Ring Ports Valve blocks flow from port 2 to port 1 only. Call for other valve configurations.

FEATURES: · Up to 18 GPM · 1820 normally closed flow path is opened when coil is energized · 1821 normally open flow path is blocked when coil is energized · Available in 40 GPM model, 700-1840 N/C or 700-1841 N/O Part Number Our Sequence No. Per Each · Valve mounts on tractor or implement 700-1820 000206 $274.30 · Easy installation Remote Normally Open On/Off Series · 3000 PSI rated 700-1821 000210 $303.39 OPTIONS Remote Normally Closed On/Off Series · 12 volt positive ground coils · 24 volt negative ground coils 700-1840 000208 $321.40 NOTE: Remote Normally Open On/Off Series 700-1840 and 700-1841 have 1-1/16 o-ring thread 700-1841 000212 $354.64

STANDARD 700-1820 KIT SHOWN · On/off normally closed control valve · Toggle switch box with mounting bracket · 12' wiring harness, 6' power wires · 3/4" o-ring fittings · 12 volt negative ground coils · Fuse kit, connectors, wire ties · Installation and operation guide Remote Normally Closed On/Off Series

© 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

H12

DVHRC-AD HCJ

HYDRAULIC CONTROLLERS FOR VALVES

DUAL FUNCTION JOYSTICK HYDRAULIC CONTROLLER

Part Number Description

Date: 1700

DUAL FUNCTION JOYSTICK HYDRAULIC CONTROLLER DVHRC-AD DVHRC-KD2 DVHRC-AS HCS-L HCS-HCR STACKABLE HYDRAULIC CONTROLLER

Our Sequence Number REMOTE CONTROL

Per Each

COMMERCIAL CONTROLS Joystick Seal Kit for DVHRD-AD GRESEN CONTROLS HCJ*

* Special Order Only

JL7350 JL7368

$1229.59 76.92

Joystick

342215

0.00

STACKABLE HYDRAULIC CONTROLLER DVHRC-AS DVHRC-KS2 DVHRC-RSK-2 DVHRC-RSK-3 DVHRC-RSK-4 Stackable Seal Kit for DVHRC-AS Stud Kit for 2 Controllers Stud Kit for 3 Controllers Stud Kit for 4 Controllers GRESEN CONTROLS DVPC-QC PNEUMATIC JOYSTICK CONTROLLER DVPC-DC DVPC-DC DVPC-DCD DVPC-H1 DVPC-H2 PNEUMATIC STACKABLE CONTROLLER DVPC-DCD DVPC-BDC DVPC-BQ DVPC-H1 DVPC-H2 DVPC-H3 BANK ASSEMBLY KITS FOR STACKABLE PNEUMATIC CONTROLLERS SEALS ARE NOT INCLUDED

Part Number Description Our Sequence Number Per Each

JL7362 JL7366 JL7370 JL7372 JL7373

865.80 54.05 108.10 61.32 72.44

HCS-L HCS-HCR

Left Section 9/16 ORB Right & Center Section COMMERCIAL CONTROLS

342210 342235

2159.22 564.75

PNEUMATIC STACKABLE CONTROLLERS Spring Return Less Handle Detented with Handle Dual Stackable Boot Quad Controller Rubber Boot Straight Handle 18 Degree Handle 35 Degree Handle Spacer 25/32" Seal Repair Kit for DVPC JL7374 JL7384 JL7398 JL7400 JL7408 JL7410 JL7412 JL7402 JL7404 354.72 434.45 71.71 113.29 52.38 46.75 46.76 116.41 77.95

DVPC-SB DVPC-SR

PNEUMATIC JOYSTICK CONTROLLER DVPC-QC With Handle JL7396 948.48

DVPC-AK-1 DVPC-AK-2 DVPC-AK-3 DVPC-AK-4 DVPC-AK-5

For One Controller For Two Controllers For Three Controllers For Four Controllers For Five Controllers

JL7444 JL7446 JL7448 JL7450 JL7452

$31.03 33.26 35.35 40.53 55.08

Joystick for Prince Two Spool Straight Shown As pictured less valve For PRINCE valves ONLY RD523CCAA5A4B1 or RD523GCGA5A4B1

VALVE AIRSHIFT KITS Valve Airshift Kits consisting of: air shift for one end of spool permitting manual operation from other end of spool from clevis end. DV20-K-113 DV35-K-213 For DV20 Valves For DV35 Valves JL7422 JL7300 $280.36 176.49

Date: 2500

PRINCE TWO SPOOL JOYSTICK HANDLE VALVE HYDRAULIC SHIFT KIT Valve Hydraulic Shift Kit contains hydraulic actuators for each end of spool permitting hydraulic operation only. DV20-K-109 DV35-K-209 For DV20 Valves For DV35 Valves JL6326 JL7322 $281.34 259.33

This handle will operate both spools using only one lever handle. The two spools can be operated either independently or simultaneously depending on handle movement.

Part Number Type Our Sequence Number Per Each

660150011 660150012

Straight 45 Degree

178377 178375

$251.85 255.03

© 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

Date: 2500

INLINE CHECK VALVES

H13

To allow free-flow in one direction and blocked flow in the reverse direction. Check Valves may also be used to provide 5 pounds, or 65 pounds of back pressure in full flow direction to assist pilot-operated solenoid valves.

Max. Pressure 3,000 PSI 1/8 to 1/2 have soft seats 3/4 and larger have steel seats MANATROL

Pipe Thread Size Part Number Max. Flow GPM Our Sequence Number Per Each | | Part | Number

Max. Pressure 3,000 PSI Female to Female GRESEN

Max. Flow GPM Our Sequence Number Per Each | Male JIC | Thread | Inches

Max. Pressure 3,000 PSI Male JIC to Male JIC GRESEN

Part Number Max. Flow GPM Our Sequence Number Per Each

1/8 1/4 3/8 1/2 3/4 1 1/2 3/4 1 1-1/4

----C-400-S C-600-S C-800-S C-1200-S C-1600-S C-800S-65 C-1200S-65 C-1600S-65 C-2000S-65

-5 8 15 25 40 15 25 40 70

5 PSI - CRACKING PRESSURE .... $.... | - - - - -800052 36.75 | - - - - -800054 42.26 | CLS-38-17F 8 800056 800058 800060 48.69 | CLS-50-17F 71.66 | CLS-75-17F 134.14 | - - - - 15 25 --

.... $.... | 9/16 .... .... | 3/4 3427882 96.79 | 7/8 3427883 292.24 | 1-1/16 3427884 292.24 | 1-3/16 .... .... | 1-5/8 .... .... .... .... .... .... .... .... | | | | -

CLS-06-27M CLS-08-27M CLS-10-27M CLS-12-27M CLS-16-27M CLS-20-27M -

8 15 25 25 40 60 -

3427885 $92.14 3427886 188.93 3427887 96.79 3427888 333.19 3427889 145.19 342789 241.98 .... .... .... .... .... .... .... ....

65 PSI - CRACKING PRESSURE 800082 46.86 | - - - - 800084 71.66 | - - - - 800086 134.14 | - - - - 800088 302.27 | - - - - -

GRINNELL & PARKER BALL VALVES for HYDRAULIC USE

Two Piece Design Ball Valve with Pipe Threaded Ends and Removable Handle || || || || || || || || || ||

Per Each || || || || Ball Valve Number

GRINNELL 600 PSI CAST BRASS

Pipe Thread Size, Ins. Ball Valve Number Our Sequence Number

PARKER 2000 PSI CARBON STEEL

Our Sequence Number Per Each | | | | Ball Valve Number

6000 PSI STEEL

Our Sequence Number Per Each

1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 Qty. Disc.:

171N 605330 $12.52 || 171N 605332 12.52 || 171N 605334 12.40 || 171N 605336 18.06 || 171N 605338 30.15 || 171N 605340 49.37 || 171N 605342 71.90 || 171N 605344 102.79 || 5 pkgs. 5%, 10 pkgs. 10%, 25 pkgs. 20%

V500CS4 V500CS6 V500CS8 V500CS12 V500CS16

800115 800116 800118 800120 800122

$40.26 38.51 40.26 58.64 75.27

| | | | | | | |

BVHP06NSS1N BVHP08NSS1N

800112 800114

$77.89 91.89

Differential Type Double Relief

HYDRAULIC CUSHION VALVE

Ball/Spring Type Dual Crossover Relief

USE-To eliminate or minimize shock experienced in starting and stopping hydraulic motors, and other hydraulic equipment. When a standard control valve is returned to neutral to stop or to start a motor, or other heavy hydraulic equipment, this creates sudden excess pressure which will break seals, tear off motor shafts, burst motor cases, or burst hoses. This sudden shock cannot be relieved through the primary relief valve in the system, and a cushion valve must be installed in the two lines from control valve to motor or cylinders. When the motor can free-wheel to a stop, a SPXT-F4 free-flow control valve and no cushion valve is used. When motor must hold load in position when stopped, as on a winch, a SP-D4 control valve and a cushion valve are used.

Maximum 2000 PSI Port Size Maximum GPM CROSS Part Number Our Sequence Number Per Each | | | | GRESEN Part Number Our Sequence Number Per Each

GPM

Setting

3/8 1/2 1/2 3/4

---30

------------RC1200DD

174849

$.... .... .... 127.51

| | | |

DXV-38-2000 DXV-50-1800 DXV-50-2000 DXV-75-2000 Qty. Disc: 2pkgs. 5%,

16 2000 20 1800 20 2000 30 2000 5 pkgs. 7%, 10 pkgs. 10%

342781 342783 342784 342786

$161.01 161.01 161.01 161.01

© 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

H14

MIX AND MATCH RELIEF VALVE CARTRIDGES & HOUSINGS

Date: 2500

Select the housing you need. Then pick a relief cartridge of the SAME BRAND. DO NOT MIX BRANDS. These may be substituted for standard reliefs of the same size.

K-RPL

K-WJL

RP51A

RP60A KC-HP GRESEN RELIEF CARTRIDGES Cartridge Only, No Housing

WH

GRESEN EMPTY RELIEF HOUSINGS Must Add Relief Cartridge

Port Size Part Number Our Sequence Number Per Each

| |

| | | | Std. Setting PSI Adjusted Pressure Range PSI

Style

GPM Rating

Fits Housing

Part Number

Our Sequence Number

Per Each

1/2 3/4 3/4 1

K-WJL-50 K-WJL-75 K-RPL-75 K-RPL-100

Inline Inline Inline Inline

343000 343010 343012 343014

$126.00 126.00 210.00 210.00

Qty. Disc: 2 pkgs. 5%, 5 pkgs. 7%, 10 pkgs. 10%

All properly designed hydraulic systems MUST contain a main system relief valve. Whether simple or complex, hydraulic systems are too expensive to run without a relief valve. REMEMBER THE RELIEF.

| | | | | | | | | | | | | | | | | | |

DIFFERENTIAL POPPET RELIEF - ADJUSTABLE WITH SHIMS Converts WH Series to Screw Adjustable K-WH-A 347510 500 1000 1200 1750 2200 2500 3000 2000 2500 500-1350 1000-1550 500-1350 1351-1750 2001-2600 2001-2600 2500-3000 20 20 20 20 20 20 20 K-WJL K-WJL K-WJL K-WJL K-WJL K-WJL K-WJL WH-500 WH-1000 WH-1200 WH-1700 WH-1950 WH-2550 WH-3000 347470 347472 347484 347477 347480 347500 347505

$38.27 87.92 87.92 87.92 87.92 87.92 87.92 88.95 286.51 295.81

BALL & SPRING RELIEF - SCREW ADJUSTABLE 1401-2500 20 K-RPL KC-HP-2000 347640 500-3500 PILOT RELIEF - SCREW ADJUSTABLE 60 K-RPL RP-60A-2500 347580

TO MAKE RELIEF VALVES USING CARTRIDGES

Port Size Part Number Use Relief Cartridges Use Housing PSI

1/2 1/2 3/4 3/4 1 1

WJT-50-1950 WJT-50-2550 K-75-HP PK-75-HP K-100-HP PK-100-HP

WH-1950 WH-2550 KC-HP-2000 RP-60A-2500 KC-HP-2000 RP-60A-2500

K-WJL-50 K-WJL-50 K-RPL-75 K-RPL-75 K-RPL-100 K-RPL-100

1950 2550 1401-2000 500-5000 1401-2000 500-5000

NOTE: Gresen does not recommend pressures in excess of 2000 PSI with pipe thread.

CUSHION VALVE CARTRIDGES and HOUSINGS

Select the housing you need. Then pick two (2) relief cartridge of the SAME BRAND. DO NOT MIX BRANDS.

RP51A GRESEN EMPTY CUSHION VALVE HOUSINGS Must Add (2) Relief Cartridges

Port Size Max. GPM Flow Part Number Our Sequence Number Per Each

| | |

| | | Part Number

WH GRESEN CARTRIDGES for CUSHION VALVES Cartridge Only, No Housing

Use Housing Per Each

1/2 3/4

20 30

K-DWV-50 K-DWV-75

342986 342988

$131.25 131.25

| |

WH Series WH Series

order (2) cartridges above order (2) cartridges above

$87.92 87.92

Qty. Disc: 2 pkgs. 5%, 5 pkgs. 7%, 10 pkgs. 10%

RP-51A CANNOT be used in the DWV Cushion Valve.

TO MAKE CUSHION VALVES USING CARTRIDGES

Port Size Part Number Use Relief Cartridges Use Housing PSI

1/2 1/2 3/4 3/4

DWV-50-A-2000 DWV-50-A-2500 DWV-75-A-2000 DWV-75-A-2500

(2) (2) (2) (2)

WH-2000 WH-2500 WH-2000 WH-2500

K-DWV-50 K-DWV-50 K-DWV-75 K-DWV-75

2000 2500 2000 2500

NOTE: Gresen does not recommend pressures in excess of 2000 PSI with pipe thread. © 2011 by Baum Hydraulics Corporation 1-800-228-9222 www.baumhydraulics.com Prices subject to change without notice

Date: 2500 COMPLETE HYDRAULIC RELIEF VALVES H15 A relief valve must be installed in the hydraulic system with each one of these pumps to prevent exploding the pump, damaging the equipment, or bursting the hose. For the correct working position for the various parts of a hydraulic system, see the diagrams on this page. Prince RD-

Gresen K-

DVLR

USE - For fast-acting and occasional relief. INLINE STYLE ALL ARE SCREW ADJUSTABLE TYPE

Port Size Relief Port Cap. GPM Pressure Set at PSI Adjustable Pressure Range PSI Part Number Our Sequence Number Per Each | | | | |

BALL and SPRING TYPE

1/2 3/4 3/4 3/4 3/4 1 1 NPT

20 24 24 30 38 38 60

1500 1500 2000 1200 1500 1500 2000 Cross RD

1000-2500 1000-2500 1201-2500 1250-1749 1401-2000 1401-2000 2000-2500

RD1850H RD1875H WJL-75-A-2000 WJL-75-A-1250 K-75-HP K-100-HP DVLR-64

Prince Prince Gresen Gresen Gresen Gresen Commercial

178415 178416 3425755 342578 Y94428 Y94430 960735

$68.51 68.51 166.59 166.59 496.51 496.51 303.90

|

|

| | |

|

| | | Gresen WJL-

Prince RV

DIFFERENTIAL POPPET TYPE

USE - Where you need a continuous acting relief. These are quiet and smooth acting. INLINE STYLE SCREW ADJUSTABLE TYPE GRESEN

Adjustable Pressure Range PSI Part Number

Port Size

Relief Port Cap. GPM

Pressure Set at PSI

Adjustable Pressure Range PSI

Part Number

Our Sequence Number

Per Each

| | | |

Relief PresPort sure Cap. Set at GPM PSI

Our Sequence Number

Per Each

1/2 1/2 3/4 3/4 3/4

20 30 30 30

2000 1000 2000 2000

1500-3000 500-1500 1500-3000 1500-3000

RV-4A RD12B RD12D RV-2H

Prince Cross Cross Prince

178466 174716 174715 178464

$68.35 | | 70.28 | 70.28 | | 68.35 |

20 20 25 25

1250 2000 1250 2000

1250-1749 2000-2599 1250-1749 2000-2599

WJL-50-A-1250 WJL-50-A-2200 WJL-75-A-1250 WJL-75-A-2200

3425405 3425505 342578 3425755

$166.59 166.59 166.59 166.59

PILOT OPERATED RELIEF

All properly designed hydraulic systems MUST contain a main system relief valve. Whether simple or complex, hydraulic systems are too expensive to run without a relief valve. REMEMBER THE RELIEF. USE - For large capacity hydraulic systems to maintain close control over the maximum operating pressure. INLINE STYLE RT- BAUM ARE KNOB ADJUSTABLE TYPE

Relief Port Cap. GPM Pressure Set at PSI

RT

Port Size

Adjustable Pressure Range PSI

Part Number

Our Sequence Number

Per Each

3/4 NPT 1-1/4 NPT

60 120

1500 1500

500-3000 500-3000

RT-06-3-E20 RT-10-3-E20

Baum Baum

$.... ....

PARTS for HYDRAULIC RELIEF VALVES

Part Number For Valve Number Our Sequence Number Per Each

K-19003

Seal Kit for WH Valves WH Relief Seal Kit EE2400

$0.85

NOTE: All Gresen relief valves are stocked as High Pressure relief valves and are factory set to operate at 1500 PSI at 7.6 GPM flow. All are marked "HP" stamped on the hex of the valve. To properly adjust relief setting use a Pressure Gauge. © 2011 by Baum Hydraulics Corporation 1-800-228-9222 www.baumhydraulics.com Prices subject to change without notice

FLOW CONTROL VALVE Date: 2500 USE - To Control Speed of Motors & Cylinders Excess Flow Can Be Used This valve will start and stop a hydraulic motor or cylinder and vary the speed smoothly over the full range. Once the speed is set with the lever it will remain constant regardless of load variation.

H16

Max. 3000 PSI Lever Adjustment Wt. 7 Lbs. PRINCE with No Relief

Port Size Part Number Max. Adj. Flow GPM Our Sequence Number Per Each

| | | | |

| | | Part Number

Max. 3000 PSI Lever Adjustment Wt. 8 Lbs. PRINCE with Adjustable Relief set @ 1500 PSI in controlled flow

Max. Adj. Flow GPM Our Sequence Number Per Each

3/8 1/2 3/4

RD137-8 RD150-16 RD175-30

With NO Relief 8 178322 16 178320 30 178318

$126.99 126.99 129.56

| | | |

-----RDRS150-16 RDRS175-30

With Adjustable Relief -16 178434 30 178436

$.... 142.29 144.97

FLOW DIVIDER - COMBINER These valves not only divide flow, but also combine flow in reverse direction.

Prince Divider/Combiner will not necessarily combine equally.

Max. 2500 PSI GRESEN

Port Size Part Number Flow Range Our Sequence Number Per Each

| | |

| | Part Number

Max. 2500 PSI PRINCE

Flow Range Our Sequence Number Per Each

1/2 1/2 1/2 3/4

--------PDC-50-50 PDC-75-50

--5-25 15-35

342970 342980

$.... .... 247.57 247.57

| | | |

RD1550.062 RD1550.078 RD1550.140 RD1575.187

2-3 3-8 8-16 12-20

178423 178422 178424 178426

$197.81 197.81 203.82 197.81

PROPORTIONAL FLOW DIVIDER Operates in One Direction ONLY USE - Flow divider must be between pump & control valve. To divide a single flow of all into TWO EQUAL FLOWS, even through work being done by one of the flows is greater than the other. A filter must be used with this flow divider. Cross drilled shifting type spool provides very accurate metering. 3 mounting holes. Max. pressure 2500 PSI

GRESEN

Port Size Part Number Input Capacity GPM Our Sequence Number Per Each

|

| | | Part Number

PRINCE

Input Capacity GPM Our Sequence Number Per Each

|

| | | Part Number

PRINCE w/ Reverse Free Flow

Input Capacity GPM Our Sequence Number Per Each

1/2 3/4

PD-50-50 PD-75-50

5 to 25 15 to 35

342950 342960

$202.89 202.89

| |

RD-250-16 8 to 16 RD275-30 16 to 30

178328 178330

$114.26 114.26

| |

RD350-16 RD375-30

8 to 16 16 to 30

178332 178334

$161.62 161.62

ADJUSTABLE FLOW CONTROL DIVIDER

EXCESS FLOW CANNOT BE USED

Part Number Port Size Flow Range Wt. Lbs. Our Sequence Number Per Each

CFDA-50 CFDA-75

1/2" 3/4"

GRESEN 2500 PSI 0-15 GPM 8 0-15 GPM 8

342720 342740

$349.01 349.01

CF=Controlled flow work port EF=Excess flow to tank ONLY P=Oil from pump

USE - To control speed of motors or cylinders in both directions. Very fine adjustment possible. Valve is pressure compensated in forward direction ONLY. An inexpensive dependable means of obtaining flow adjustment where the exact flow cannot be determined or where frequent flow change is required. Provides a smooth & constant output flow regardless of pressure changes at the controlled flow port. Rotating the adjusting knob varies the flow from the controlled flow port. After the controlled flow demand is satisfied, the balance of the inlet flow passes through the excess flow port which is connected back to tank. The excess flow port is NOT a work port. The model CFD-A adjustable flow control is NOT available with a built-in relief valve. © 2011 by Baum Hydraulics Corporation 1-800-228-9222 www.baumhydraulics.com Prices subject to change without notice

Date: 2500

NEEDLE & SHUT-OFF VALVE

Controlled Flow in BOTH Directions USE - Throttling and shut-off valves suitable for speed control of cylinders and motors. MANATROL with COLOR FLOW 3,000 PSI Maximum Pressure Made of Steel with Color Flow MARSH 10,000 PSI

H17

3,000 PSI 2-step needle to give fine adjustment in the first 3 turns & conventional throttling in the last 3. VALVE ADJUSTMENT These valves may be adjusted by loosening socket set screw in adjustment knob & rotating. Turn knob clockwise (CW) to decrease flow setting, counterclockwise (CCW) to increase flow setting. After adjustment, hold knob & retighten socket set screw. MANATROL

Size Part Number Max. Flow @ 1000 PSI Our Sequence Number Per Each | | Part Number

The MV Series needle valves give precise metering & shut-off. May be adjusted by rotating adjusting handle. Rotate handle clockwise (CW) to decrease flow, counter-clockwise (CCW) to increase flow. The needle stem is provided with color rings to indicate relative settings. MANATROL

Max. Flow @ 1000 PSI Our Sequence Number Per Each | | Part Number

Maximum Pressure FOR FASTER, LESS CRITICAL NEEDLE ADJUSTMENTS EASILY ADJUSTABLE UNDER PRESSURE MARSH

Max. Flow @ 1000 PSI Our Sequence Number Per Each

1/4 3/8 1/2 3/4 1 Manatrol

N-400-S 5 800032 N-600-S 8 800034 N-800-S 15 800036 N-1200-S 25 800038 N-1600-S 40 800040 Qty. Disc: 10% for 10 pkgs.

$46.86 57.88 75.34 98.31 372.10

| | | | |

MV-400-S MV-600-S MV-800-S MV-1200-S MV-1600-S

5 8 15 25 40

800092 800094 800096 800098 800100

$47.78 67.99 84.53 138.73 293.09

| | | | |

N1512 N1513 N1514 N1516 N1518

5 8 15 25 40

178688 $100.33 178752 100.33 178816 100.33 178818 323.83 178820 439.66

FLOW CONTROL VALVES

Controlled flow in ONE direction. Free flow in reverse.

Pipe Thread

EASY TO READ. . . . .EASY TO ADJUST FULL COLOR & NUMBERICAL READOUT Inline in sizes from 1/8" to 1" Flows of 4 to 40 GPMMaximum pressure of 3,000 PSI Patented "Colorflow" adjustment reference Made of Steel

Qty. Disc: 10% for 10 pkgs. SERIES F LINE-MOUNTED FLOW CONTROL VALVES Precisely controlled flow and shut-off in one direction, free flow in reverse. Two-step needle to give fine adjustments for low flows in the first three turns and conventional throttling in the last three turns. Has a set screw to lock valve settings.

Size PARKER Part Number Max. Flow Our Sequence Number Per Each

No Qty. Discounts

PRECISE Part Number Max. Flow Our Sequence Number Per Each

Size

1/4 3/8 1/2 3/4 1

F-400-S F-600-S F-800-S F-1200-S F-1600-S

5 8 15 25 40

800012 800014 800016 800018 800020

$45.94 57.88 81.77 118.52 311.46

1/4 3/8 1/2 3/4 1

WFC-400 WFC-600 WFC-800 WFC-1200 WFC-1600

5 8 15 25 40

178490 178492 178494 178496 178498

$35.44 38.12 47.25 91.82 223.37

SAND SPREADER VALVE

Dual Flow Regulator Valve with on-off and Relief. Working Pressure 2000 PSI Set at 1500 PSI SAE O-Ring Boss Ports USE: With a fixed displacement pump where 2 controlled flows and an on-off manual dump are required. You CAN NOT use excess flow. Excess flow must be hooked directly to tank. Very popular for salt & sand and other agricultural equipment. MANUAL ON-OFF

Part Number Auger Port Spreader Port Our Sequence Number Per Each | | Part Number

12 VOLT ON-OFF

Auger Port Spreader Port Our Sequence Number Per Each

QDB-12-A07B16AR QDB-12-A10B30AR

7 10

16 30

342251 342244

$693.10 693.10

| |

QDS-12-A07B16AR QDS-12-A10B30AR

7 10

16 30

342248 342250

$919.96 919.96

© 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

H18

Metro 409-05

PRESSURE LOCK VALVES ELIMINATES CYLINDER CREEP

For Use With Double-Acting 4-way Valves ONLY Prince LO-50-D Gresen LO-50-D

Date: 2500

Gresen LD1 & LD2

LD2 Double 2500 PSI

Port Size METRO Part Number Max. Our GPM Sequence Flow Number Per Each | PRINCE | Part | Number

2500 PSI

Max. Our GPM Sequence Flow Number Per Each | GRESEN | Part | Number

2500 PSI

Max. Our GPM Sequence Flow Number Per Each | GRESEN | Part | Number

3000 PSI

Our Pilot Sequence Port Number Per Each

DOUBLE ACTING - To Lock in BOTH DIRECTIONS with a 4-way Valve ----- -$.... | RD1450 30 178340 $159.15 | LO-50-D 409-05 15 704983 185.53 | RD1475 30 178345 159.15 | - - - - ----- -.... | - - - - -.... | LO-10-D SINGLE ACTING - To Lock in ONE DIRECTION ONLY with a 4-way Valve 1/2 - - - - - - .... | - - - - -.... | LO-50-S

1/2 3/4 7/8

25 -30 25

342800 $212.20 | LD1-50-1DR 1/2 342818 $601.37 .... | LD2-16-2-D 1-5/16 .... 342809 212.20 | - - - - -.... 342810 190.79 | LD1-50-1SR 1/2 342816 490.64

USE - To lock a cylinder in position and prevent its movement due to leakage or slippage when the control valve is in neutral position. * NOTE: 7/8 is o-ring ports PRESSURE LOCK HOOK-UP Lock valves and double-acting cylinders are hooked up as shown below. Install pressure lock in both hose lines between control valve and cylinder. For single-acting cylinder use same layout except Hose A. PRIORITY DIVIDER FLOW DIVIDER for POWER STEERING Prince

GRESEN LINE THROTTLE VALVES NON-ADJUSTABLE FLOW One Way Line Throttle USE - To regulate maximum speed of cylinders in one direction. ECONOMY TYPE. Restricts the flow in one direction, full flow in opposite direction. Will operate satisfactorily in any position. 1/2" pipe thrd. male & female outlets, 2-1/8" long. Plastic ball has drilled orifice.

Part Number Thread Size Inches Plastic Ball Color Restricted Capacity GPM at 1000 PSI Approx. Size Orifice in Restrictor Inch Our Sequence Number Per Each

USE - To divide one flow of oil into one constant volume flow and another excess volume flow regardless of pump speed or pressure. For use for power steering or other applications where two separate power circuits are to be served from one pump. A filter must be used with this flow divider.

Part Number Constant Flow Capacity GPM Our Sequence Number Per Each

PRINCE 1/2" INLET & EXCESS 1/2" CONSTANT 3/8" TANK PORT ADJUSTABLE RELIEF SET 1500 PSI RD450R-4 4 GPM 30 GPM 178350 $166.56 RD450R-6 6 GPM 30 GPM 178352 166.56 RD450R-8 8 GPM 30 GPM 178354 166.56 PRINCE 3/4" INLET & EXCESS 3/4" CONSTANT 1/2" TANK PORT ADJUSTABLE RELIEF SET 1500 PSI RD405R-4 4 GPM 30 GPM 178356 166.56 RD405R-6 6 GPM 30 GPM 178358 166.56 RD405R-8 8 GPM 30 GPM 178360 166.56 GRESEN FLOW DIVIDERS Gresen 1-1/16 all ports except relief 3/4 o-ring 3500 PSI valve

LT-50-4 LT-50-6 LT-50-9 LT-50-12 LT-50-15 LT-10-0 LT-50-0 LT-75-00

GRESEN LINE 1/2 Brown 1/2 Purple 1/2 Red 1/2 Yellow 1/2 Green 7/8 1/2 3/4

THROTTLE VALVES 1 1/32 3429331 $37.59 3 1/16 342934 37.59 5 3/32 342936 37.59 11 1/8 342937 37.59 14 5/32 342938 37.59 342915 342933 342930 59.30 37.59 88.54

GRESEN CHECK VALVES Neutral Check None Neutral Check None Neutral Check None

ALSO AVAILABLE IN 3/4 O-RING THREAD

RESTRICTOR SWIVELS-RESTRICTS BOTH WAYS Five in a Package

Restricted Capacity GPM at 1000 PSI Size Orifice in Restrictor Inch Our Sequence Number

Part Number

Constant Flow

Capacity GPM

Our Sequence Number

Per Each

DC25A-12

ADJ.

30 GPM

342698

$307.13

To change constant flow in non-adjustable models, change orfice plate.

Per Each Part Number Our Sequence Number Per Each

Part Number

Pipe Thread

2H0104-04R 1/4 .5838 2H0106-06R 3/8 .5838 2H0108-08R 1/2 .5838 © 2011 by Baum Hydraulics Corporation

1/32 1/32 1/32

K-OP-1 207080 $4.37 K-OP-3 207082 5.66 K-OP-4 207086 7.11 1-800-228-9222 www.baumhydraulics.com

342706 342707 342708

$8.10 5.21 8.10

Prices subject to change without notice

Date: 2500

HYDRAULIC SELECTOR VALVES

H19

DOUBLE SELECTOR VALVE USE - To operate two sets of double-acting cylinders one at a time with one 4-way (double-acting) control valve. This valve is used where one double-acting cylinder is on the front and one is on the rear of the tractor, and both are operated by the same control valve. Also use this valve to add another double-acting cylinder on a tractor where you want to use the existing control valve to operate both double cylinders separately. This hook-up is shown in the circuit diagram BELOW LEFT.

Less Endcap

Port Size

Part Number

Capacity GPM

Our Sequence Number

Per Each

| |

Part Number

Capacity Our Sequence GPM Number

Per Each

| |

Part Number

Capacity Our Sequence GPM Number

Per Each

1/2 3/4 1 1-1/16

PRINCE Max. DS-1A1E DS-4A1E ---------

Pressure 2500 PSI 20 178336 $155.82 30 178337 155.82 -.... -....

| | |

GRESEN Max. Pressure 2500 PSI -----$.... DS75 24 342520 208.48 -----.... O-Ring Thread Max. Pressure 3000 PSI | DS12 24 342521 208.48

| | | |

CROSS Max. Pressure 2500 PSI -----$.... -----.... SD4BALA6 40 174858 162.33 -----....

SINGLE SELECTOR VALVE USE - To operate two control valves from one pump or, to operate separately two single-acting cylinders from one control valve. This hydraulic selector valve is particulary useful on tractors with a backhoe mounted on the rear and a loader, dozer or snowplow on the front. The selector valve can be mounted between the pump and two groups of control valves. This allows you to direct the flow either to the control valves for the loader in front or to the control valves for the backhoe in the rear. This hookup is shown in the circuit diagram BELOW RIGHT.

Port Size

Part Number

Capacity GPM

Our Sequence Number

Per Each

| |

Part Number

Capacity Our Sequence GPM Number

Per Each

| |

Part Number

Capacity Our Sequence GPM Number

Per Each

1/2 3/4 1

PRINCE Max. Pressure 3000 PSI RD950 20 178418 $139.07 RD975 30 178420 139.07 -----....

| | |

GRESEN Max. Pressure 2000 PSI S50 15 342380 $106.11 S75 24 342400 135.89 S100 40 342420 161.02 | |

| | |

CROSS Max. Pressure 2500 PSI VS2BKLF2 20 174854 $73.33 VS4BKLF6 40 174856 99.44 -----....

Part Number

GRESEN Repair Kits for GRESEN Selector Valves SINGLE SELECTOR VALVE

Our Seq. Number

Per Each |

K-13001A K-15001A

Seal Kit for S-50 Seal Kit for S-100

EE2388 EE2390

$0.35 0.77

DOUBLE SELECTOR VALVE

| | | | | | | | | | | | | | | | |

GRESEN HOLDING VALVES

Holding or counter balance valve used to keep a cylinder or motor from running away. Has reverse free flow. Use where smooth operation and zero leakage of cylinders is required like on a man basket or crane. They will keep motors from cavitating and running free.

Our Sequence Number Per Each

Part Number

Ports

MHB-015-LAAC-51E MHB-030-LAAC-08B

Unloading 9/16 Ports, 9/16 Pilot Unloading 1/2 Ports, 1/4 Pilot

342397 342398

$166.13 265.71 MHB-030

Qty. Disc: 2 pkgs. 5%, 5 pkgs. 7%, 10 pkgs. 10% © 2011 by Baum Hydraulics Corporation 1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

H20

LARGE HYDRAULIC RETURN LINE PAPER ELEMENT A LARGE SIZE FULL-FLOW IN-LINE FILTER

Date: 2000

USE - Install in return line between the control valve and the tank. This full flow filter has a built-in by-pass valve which opens automatically when filter is clogged or overloaded. Dial indicator tells when filter is dirty. Filter element easily removed for replacement. Install filter at high point of system. Filter gives full-flow filtration until clogged with dirt.

GRESEN ASSEMBLY 1-1/4" PIPE SPIN-ON

BAUM ASSEMBLY 1-1/4" OR 1" PIPE SPIN-ON

BAUM ASSEMBLY 1-1/2" PIPE SPIN-ON

Specify Pipe Size When Ordering

GRESEN Number GPM Our Sequence Number Per Each | | | BAUM Number 1" Sequence Number GPM 1-1/4" Sequence Number 1" and | 1-1/4" | Per Each | GPM 1-1/2" Our Sequence Number 1-1/2" Per Each

FILTER ASSEMBLIES WITHOUT GAUGE PORTS With FINE 10 Micron Paper Element | FSP212-1EDNH 65 345280 $95.44 | -----.... | FSP212-1EDNN FSP212-1EDNN Long Y94836 Y94838 62 70 28 70 70 35 40 12 Y94864 Y94866 Y94868 Y94870 Y94872 Y94874 Y94876 Y94878 | $40.55 | 50.70 | | 65.72 | | 40.54 | 50.70 | | 45.21 | 60.23 | | 68.29 | 62 70 28 70 78 35 40 12 Y94920 Y94922 Y94924 Y94926 Y94928 Y94930 Y94932 Y94934 $52.93 63.08 78.11 52.92 63.08 57.60 72.61 80.67

With FINE 10 Micron Water Absorbing Paper Element -----.... | FSP212-1EDNN-AZ Lg. Y94840 With COARSE 25 Micron Paper Element | FSP212-1JDNH 75 345310 95.44 | -----.... | With EXTRA FINE 3 Micron Paper Element | FSP212-1ADNN 45 .... | -----.... | FSP212-1JDNN FSP212-1JDNN Long FSP212-1ADNN FSP212-1ADNN Long Y94842 Y94844 Y94846 Y94848

With EXTRA FINE 3 Micron Water Absorbing Paper Element -----.... | FSP212-1ADNN-AZ Lg. Y94850

FILTER ASSEMBLIES WITH GAUGE PORTS With FINE 10 Micron Paper Element FSP212-1EDNA 65 -----.... .... | | | FSP212-1EDNAC Y94986 FSP212-1EDNAC Long Y94988 Y94990 Y94992 Y94994 62 70 28 70 70 35 40 12 Y95014 Y95016 Y95018 Y95020 Y95022 Y95024 Y95026 Y95028 | 42.26 | 52.41 | | 67.44 | | 42.25 | 52.41 | | 46.92 | 61.94 | | 70.00 | | 22.32 | 22.32 | | 24.03 | 24.03 | 62 70 28 70 78 35 40 12 Y95070 Y95072 Y95074 Y95076 Y95078 Y95080 Y95082 Y95084 54.64 64.79 79.82 54.64 64.79 59.31 74.32 82.39

With FINE 10 Micron Water Absorbing Element -----.... | FSP212-1EDNAC With COARSE 25 Micron Paper Element FSP212-1JDNA 75 .... -----.... | | | FSP212-1JDNAC FSP212-1JDNAC Long

With EXTRA FINE 3 Micron Paper Element | FSP212-1ADNA 45 .... | -----.... |

FSP212-1ADNAC Y94996 FSP212-1ADNAC Long Y94998

With EXTRA FINE 3 Micron Water Absorbing Paper Element -----.... | FSP212-1ADNAC-AZ Lg. Y95000 Without Gauge Ports - - - -- - - -With Gauge Ports - - - -----| | | | | |

FILTER HEADS ONLY .... .... .... .... SF-100-25-0 SF-120-25-0 SF-100-25-4 & 6 SF-120-25-1 & 3 501141 501150 501143 501155 - - - -SF-150-25-0 501200 .... 34.70 .... 36.41

- - - -SF-150-25-1&3 501205

REPLACEMENT ELEMENTS

|

| | | | | | | | | | | |

|

| | | | | | | | | 18.23 | 28.38 | 43.41 | | 18.22 | 28.38 | | 22.90 | 37.91 | 45.97 |

Fine 10 Micron Element Standard ----Extra Long ----Water Absorbing - - - - -

.... .... ....

SE-10 LE-10 LE-10AZ SE-25 LE-25 SE-3 LE-3 LE-03AZ

501045 501050 501055 501060 501065 501070 501075 501080

SE-10 LE-10 LE-10AZ SE-25 LE-25 SE-3 LE-3 LE-03AZ

501045 501050 501055 501060 501065 501070 501075 501080

18.23 28.38 43.41 18.22 28.38 22.90 37.91 45.97

Coarse 25 Micron Element | Standard K-23019 345800 33.34 | Extra Long ----.... | Extra Fine 3 Micron Element | Standard K-23020 345820 18.06 | Extra Long ----.... | Water Absorbing - - - - .... | Call for Quantity Discounts © 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

Date: 2000

MEDIUM HYDRAULIC RETURN LINE PAPER ELEMENT OR WASHABLE SCREEN FILTER AN ECONOMY MEDIUM SIZE RETURN-LINE FILTER

H21

USE - Install in return line between the control valve and the tank. This full flow filter has a built-in by-pass valve which opens automatically when filter is clogged or overloaded. Dial indicator tells when filter is dirty. Filter element easily removed for replacement. Install filter at high point of system. Filter gives full-flow filtration until clogged with dirt.

GRESEN ASSEMBLY 3/4" PIPE SPIN-ON

BAUM ASSEMBLY 1/2" OR 3/4" PIPE SPIN-ON

BAUM ASSEMBLY 1" PIPE SPIN-ON

Specify Pipe Size When Ordering

GRESEN Number GPM Our Sequence Number Per Each | | | BAUM Number 1/2" Sequence Number GPM 3/4" Sequence Number 1/2" | 3/4" | Per Each | GPM 1" Our Sequence Number 1" Per Each

FILTER ASSEMBLIES WITHOUT GAUGE PORTS With FINE 10 Micron Paper Element | FSP107-1EDNN 23 344860 $103.25 | -----.... | FSP107-1EDNN FSP107-1EDNN Long Y94500 Y94502 Y94504 Y94506 Y94508 18 25 7 25 10 Y94520 Y94522 Y94524 Y94526 Y94528 | $22.44 | 29.92 | | 29.92 | | 22.44 | | 46.16 | | 24.20 | 31.69 | | 31.69 | | 24.20 | | 47.92 | 18 25 7 25 10 Y94540 Y94542 Y94544 Y94546 Y94548 $26.17 33.65 33.65 26.17 49.89

With FINE 10 Micron Water Absorbing Paper Element -----.... | FSP107-1EDNN-AZ With COARSE 33 Micron or 25 Micron Paper Element FSP107-1LDNN 27 344890 46.47 | FSP107-1LDNN With EXTRA FINE 3 Micron Paper Element | -----.... | With FINE 10 Micron Paper Element FSP107-1EDNA 23 -----| | | FSP107-1ADNN-AZ

FILTER ASSEMBLIES WITH GAUGE PORTS .... .... FSP107-1EDNAC Y94610 FSP107-1EDNAC Long Y94612 Y94614 Y94616 18 25 7 25 10 Y94630 Y94632 Y94634 Y94636 Y94638 18 25 7 25 10 Y94650 Y94652 Y94654 Y94656 Y94658 27.36 34.84 34.84 27.36 51.08

With FINE 10 Micron Water Absorbing Paper Element -----.... | FSP107-1EDNAC-AZ With COARSE 33 Micron or 25 Micron Paper Element FSP107-1LDNA 27 .... | FSP107-1LDNAC

With EXTRA FINE 3 Micron Water Absorbing Paper Element -----.... | FSP107-1ADNAC-AZ Lg. Y94618

FILTER HEADS ONLY Without Gauge Ports .... .... .... With Gauge Ports .... .... .... | | | | | | | | |

|

ZAF-05-50-0 ZAF-07-25-0 ZAF-10-25-0 ZAF-05-50-1 & 3 ZAF-07-25-1 & 3 ZAF-10-25-1 & 3

501260 501275 501285 501262 501280 501290

| 15.44 | 13.68 | 17.41 | | | 15.44 | 15.44 | 18.60 |

|

HOW TO INSTALL FILTERS

Buy filters with an extra element. Install and operate filter for one hour to clean the oil, then change element. Install filter upright in high point of system. With Gresen filters, install casting first, then attach bottom allowing 1 inch clearance. Find arrow on casting for correct flow direction. Follow enclosed instructions to install and adjust dial indicator. Install with the lower surface of the filter head casting above reservoir oil level so that when the filter housing is removed oil supply in reservoir will not drain. Paper Element will filter three times as thoroughly as the Wire Cloth Element. Install filter at high point of the system.

REPLACEMENT ELEMENTS

|

|

| | | | | | | | | | | 8.76 | 16.24 | 16.24 |

|

| | | | | | | | | | Fine 10 Micron Element | Standard K-22001 345570 15.87 | Extra Long ----.... | Water Absorbing - - - - .... |

|

AE-10 AE-10L AE-10AZ AE-25 AE-03AZL

501005 501010 501015 501020 501000

Coarse 25 Micron Element | Standard K-22002 345600 15.87 |

|

| 8.76 |

|

Extra Fine 3 Micron Element ----Date: 2500

Part Number O.D.

....

| |

| 32.48 |

Our Sequence Number Per Each

GASKETS & SEALS for LARGE GRESEN Filters

x I.D. x Thickness x Height

Gasket for FSP212 Series Filter 11872-001 5/16 x 4-17/32 Flat Center Post Seal Between Can & Center on Bottom 1575-001 3-3/4 x 1-3/4 Large Square Cut Housing Seal Between Can & Head 1576-001 4-3/4 x 4-3/8 Call for Quantity Discounts © 2011 by Baum Hydraulics Corporation

x x x

1/4 1 3/16

x x x

5/16 1/16 1/4

360595 359500 359520

$2.41 2.80 5.10

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

H22

LARGE HYDRAULIC RETURN LINE PAPER ELEMENT A LARGE SIZE FULL-FLOW IN-LINE FILTER

Date: 2000

USE - Install in return line between the control valve and the tank. This full flow filter has a built-in by-pass valve which opens automatically when filter is clogged or overloaded. Dial indicator tells when filter is dirty. Filter element easily removed for replacement. Install filter at high point of system. Filter gives full-flow filtration until clogged with dirt.

BAUM ASSEMBLY SPIN-ON

BAUM ASSEMBLY SPIN-ON

GRESEN ASSEMBLY SPIN-ON

200 PSI

2" Split Flange & 1-1/2" Pipe Thd. Combination SIDE-BY-SIDE

BAUM Number GPM Our Sequence Number Per Each | BAUM | In-Line

200 PSI

2" Split Flange & 1-1/2" Pipe Thd. Combination MODULAR LINE

GPM Our Sequence Number Per Each | GRESEN | Number

200 PSI

DROP-IN 1-1/2" Split Flange & 1-1/4" NPTF Combination

GPM Our Sequence Number Per Each

With FINE 10 Micron Paper Element FSP415-5EDNNK 108 Y95136 FSP415-5EDNNK Long 110 Y95138

FILTER ASSEMBLIES WITHOUT GAUGE PORTS | | $142.29 | FSP615-5EDNNK 128 Y95268 $126.55 | - - - - 162.59 | FSP615-5EDNNK Long 138 Y95270 146.85 | - - - - 40 132 142 Y95272 Y95274 Y95276 Y95278 Y95280 Y95282 | 176.90 | - - - - | 126.53 | FLR215-9LDNH 146.85 | - - - - | 135.88 | - - - - 165.91 | - - - - | 182.03 | - - - - -

---84 -----

$.... .... .... 345180 279.49 .... .... .... ....

With FINE 10 Micron Water Absorbing Element FSP415-5EDNNK-LAZ 38 Y95140 192.64 | FSP615-5EDNNK-LAZ With COARSE 25 Micron Paper Element FSP415-5LDNNK 115 Y95142 FSP415-5LDNNK Long 130 Y95144 | 142.27 | FSP615-5LDNNK 162.59 | FSP615-5LDNNK Long

With EXTRA FINE 3 Micron Paper Element | FSP415-5ADNNK 85 Y95146 151.62 | FSP615-5ADNNK 95 FSP415-5ADNNK Long 90 Y95148 181.65 | FSP615-5ADNNK Long 105 With EXTRA FINE 3 Micron Paper Water Absorbing Element FSP415-5ADNNK-LAZ 25 Y95150 197.77 | FSP615-5ADNNK-LAZ With FINE 10 Micron Paper Element FSP415-5EDNACK 108 Y95202 FSP415-5EDNACK Long 110 Y95204 30

FILTER ASSEMBLIES WITH GAUGE PORTS | | 145.82 | FSP615-5EDNACK 130 Y95334 129.97 | - - - - 166.12 | FSP615-5EDNACK Long 140 Y95336 150.27 | - - - - Y95338 Y95340 Y95342 Y95344 Y95346 Y95348 | 180.32 | - - - - | 129.95 | FLR215-9LDNH 150.27 | - - - - | 139.30 | - - - - 169.33 | - - - - | 185.45 | - - - - | 90.09 | - - - - | 93.51 | - - - - -

---84 -----

.... .... .... 345180 279.49 .... .... .... ....

With FINE 10 Micron Water Absorbing Element FSP415-5EDNACK-LAZ 38 Y95206 196.17 | FSP615-5EDNACK-LAZ 40 With COARSE 25 Micron Paper Element FSP415-5LDNACK 115 Y95208 FSP415-5LDNACK Long 130 Y95210 | 145.80 | FSP615-5LDNACK 132 166.12 | FSP615-5LDNACK Long 142

With EXTRA FINE 3 Micron Paper Element | FSP415-5ADNACK 85 Y95212 155.15 | FSP615-5ADNACK 95 FSP415-5ADNACK Long 90 Y95214 185.18 | FSP615-5ADNACK Long 105 With EXTRA FINE 3 Micron Paper Water Absorbing Element FSP415-5ADNACK-LAZ 25 Y95216 201.30 | FSP615-5ADNACK-LAZ 30 FILTER HEAD ONLY Without Gauge Ports ZDF-2215-25-0-00 With Gauge Ports ZDF-2215-25-1 & 3-00 501335 501340 | 105.83 | MF-2215-25-0-2-0 | 109.36 | MF-2215-25-1 & 3-2-0

501250 501255

.... ....

REPLACEMENT ELEMENTS

|

| | | | | | | | | 18.23 | SE-10 28.38 | LE-10 43.41 | LE-10AZ | 18.22 | SE-25 28.38 | LE-25 | 22.90 | SE-3 37.91 | LE-3 24.30 | LE-03AZ

|

| | | | | | | | | 18.23 | K-23026 28.38 | - - - - 43.41 | - - - - | 18.22 | K-23027 28.38 | - - - - | 22.90 | K-23044 37.91 | - - - - 24.30 | - - - - -

Fine 10 Micron Element Standard SE-10 Extra Long LE-10 Water Absorb. LE-10AZ Coarse 25 Micron Element Standard SE-25 Extra Long LE-25 Extra Fine 3 Micron Element Standard SE-3 Extra Long LE-3 Water Absorb. LE-03AZ Call for Quantity Discounts

501045 501050 501055 501060 501065 501070 501075 501000

501045 501050 501055 501060 501065 501070 501075 501000

345765

28.07 .... .... 28.07 .... 22.36 .... ....

345735

345850

© 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

Date: 2000

MEDIUM HYDRAULIC SUCTION LINE SPIN-ON SCREEN FILTER

H23

USE-Install in the suction line between pump inlet and the tank except Sump type, which is installed in the tank. This full flow filter has a built-in by-pass valve which opens automatically when filter is clogged or overloaded. Dial indicator tells when filter is dirty. Filter element easily removed for replacement. Filter gives full-flow filtration until clogged with dirt.

BAUM ASSEMBLY 1/2" OR 3/4" OR 1" PIPE SPIN-ON

BAUM Part Number

GPM

1/2" Our Sequence Number

Per Each

| | BAUM | Part Number

GPM

3/4" Our Sequence Number

Per Each

| | BAUM | Part Number

GPM

1" Our Sequence Number

Per Each

FILTER ASSEMBLIES WITHOUT GAUGE PORTS With Coarse 100 Mesh Wire Screen Element 91 Square Inch 141 Micron | FSP107-1XDNN 5 Y94510 $44.70 | FSP107-1XDNN 9 Y94530 $44.75 | FSP107-1XDNN

14

Y94550 $48.49

FILTER ASSEMBLIES WITH GAUGE PORTS Filter with COARSE 100 Mesh Screen Element 91 Square Inch 141 Micron FSP107-1XDNAC 5 Y94620 46.52 | FSP107-1XDNAC 9 Y94640 46.52 | FSP107-1XDNAC 14 Without Gauge Ports ZAF-05-05-0 ZAF-07-05-0 ZAF-10-05-0 FILTER HEAD | 13.62 | 13.68 | 17.41 | ONLY With Gauge Ports ZAF-05-05-5 ZAF-07-05-5 ZAF-10-05-5

Y94660

50.25

501264 501281 501283

501266 501270 501284

15.44 15.44 19.17

REPLACEMENT ELEMENTS 100 Mesh Element for 1/2", 3/4" and 1" Meduim Assemblies AE-100 501025 31.08 | -----

....

LARGE HYDRAULIC SUCTION LINE SPIN-ON SCREEN FILTER BAUM ASSEMBLY TWIN

2" Split Flange & 1-1/2" Pipe Thd. Combination SIDE-BY-SIDE

BAUM ASSEMBLY IN-LINE

2" Split Flange & 1-1/2" Pipe Thd. Combination MODULAR LINE

BAUM Twin Side by Side Number

GPM

Our Sequence Number

Per Each

| |

BAUM Twin In-Line Number

GPM

Our Sequence Number

Per Each

FILTER ASSEMBLIES WITHOUT GAUGE PORTS Filter with 2 COARSE 100 Mesh Screen Element 200 Square Inch Each 141 Micron FSP415-5SBNNK 50 Y95164 $203.27 | FSP615-5SBNNK Filter with 2 COARSE EXTRA LARGE 100 Mesh Wire Screen Element 380 Square Inch Each 141 Micron FSP415-5TBNNK 64 Y95166 238.67 | FSP615-5TBNNK FILTER ASSEMBLIES WITH GAUGE PORTS Filter with 2 COARSE 100 Mesh Screen Element 200 Square Inch Each 141 Micron FSP415-5SBNEK 50 Y95230 205.03 | FSP615-5SBNEK Filter with 2 COARSE EXTRA LARGE 100 Mesh Wire Screen Element 380 Square Inch Each 141 Micron FSP415-5TBNEK 64 Y95232 240.43 | FSP615-5TBNEK Without Gauge Ports ZDF-2215-05-0-00 With Gauge Ports ZDF-2215-05-5-00 FILTER HEAD ONLY | 105.83 | MF-2215-05-0-2-0 | 107.59 | MF-2215-05-5-2-0 REPLACEMENT ELEMENTS

50 64

Y95296 Y95298

$187.53 222.93

50 64

Y95362 Y95364

189.24 224.64

501310 501315

501225 501230

90.09 91.80

| With 100 Mesh Element Standard Extra Long Date: 2500

Part Number O.D. x

SE-100 LE-100

501085 501090

48.72 66.42

| | |

SE-100 LE-100

501085 501090

Our Sequence Number

48.72 66.42

Per Each

GASKETS & SEALS for LARGE GRESEN Filters

I.D. x Thickness x Height

Gasket for FSP212 Series Filter 11872-001 5/16 x 4-17/32 Flat Center Post Seal Between Can & Center on Bottom 1575-001 3-3/4 x 1-3/4 Large Square Cut Housing Seal Between Can & Head 1576-001 4-3/4 x 4-3/8 Call for Quantity Discounts © 2011 by Baum Hydraulics Corporation

x x x

1/4 1 3/16

x x x

5/16 1/16 1/4

360595 359500 359520

$2.41 2.80 5.10

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

H24

LARGE HYDRAULIC SUCTION LINE WASHABLE SCREEN FILTER LARGE SIZE FULL FLOW IN-LINE FILTER

Date: 2000

USE-Install in the suction line between pump inlet and the tank except Sump type, which is installed in the tank. This full flow filter has a built-in by-pass valve which opens automatically when filter is clogged or overloaded. Dial indicator tells when filter is dirty. Filter element easily removed for replacement. Filter gives full-flow filtration until clogged with dirt.

BAUM ASSEMBLY LARGE SUCTION SPIN-ON

GRESEN ASSEMBLY DROP-IN

1", 1-1/4" & 1-1/2" Pipe Thread LARGE SUCTION

BAUM Spin-On Number GPM 1" Sequence Number GPM 1-1/4" Sequence Number GPM 1-1/2" Sequence Number Per Each | |

1-1/2" Split Flange & 1-1/4" Pipe Thd Combination DROP-IN

GRESEN Drop-In Number GPM Our Sequence Number Per Each

FILTER ASSEMBLIES WITHOUT GAUGE PORTS Filter with COARSE 100 Mesh Screen Element 200 Square Inch 141 Micron | FSP112-1SBNN 15 Y94662 25 Y94720 32 Y94744 $83.42 | FLR215-9SANH | Filter with COARSE EXTRA LARGE 100 Mesh Wire Screen Element 380 Square Inch 141 Micron FSP112-1TBNN 18 Y94664 30 Y94722 40 Y94746 101.12 | - - - - -

53 --

345181

$305.98 ....

FILTER ASSEMBLIES WITH GAUGE PORTS Filter with COARSE 100 Mesh Screen Element 200 Square Inch 141 Micron | | FSP112-1SBNDF 15 Y94666 25 Y94778 32 Y94802 85.13 | - - - - -.... | Filter with COARSE EXTRA LARGE 100 Mesh Wire Screen Element 380 Square Inch 141 Micron FSP112-1TBNDF 18 Y94668 30 Y94780 40 Y94804 102.83 | - - - - -.... | With EXTRA COARSE 60 Mesh Screen Element 220 Micron (K-23011) -----.... | -----.... FILTER HEAD ONLY Without Gauge Ports SF-100-05-0 SF-120-05-0 SF-150-05-0 With Gauge Ports SF-100-05-4 & 6 SF-120-05-4 & 6 SF-150-05-4 & 6 1" 1-1/4" 1-1/2" 1" 1-1/4" 1-1/2" 501130 501145 501175 501132 501147 501180 22.32 24.02 34.70 24.03 24.03 36.41 | | | | | | | | |

-----

....

-----

....

REPLACEMENT ELEMENTS

|

| | | | | | | | | | | | | | |

With 100 Mesh Element Standard Extra Long Extra Heavy With 60 Mesh Element

SE-100 LE-100 ---------

501085 501090

48.72 66.42 .... ....

K-25001 ----K-25002 K-23011

345940 345950 345700

39.87 .... 41.67 33.05

NOTE: Filter assemblies using 100 mesh wire screen element for suction line should use the filter head with the 5 PSI bypass spring setting. Those with gage ports need the proper gage port location for a vacuum gage. Date: 2500

Part Number O.D. x

GASKETS & SEALS for LARGE GRESEN Filters

I.D. x Thickness x Height Our Sequence Number Per Each

Gasket for FSP212 Series Filter 11872-001 5/16

x

4-17/32

x x x

1/4 1 3/16

x x x

5/16 1/16 1/4

360595 359500 359520

$2.41 2.80 5.10

Flat Center Post Seal Between Can & Center on Bottom 1575-001 3-3/4 x 1-3/4 Large Square Cut Housing Seal Between Can & Head 1576-001 4-3/4 x 4-3/8 Call for Quantity Discounts © 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

Date: 2500

FLOW EZY TANK-MOUNTED SUCTION STRAINERS; RETURN LINE STRAINERS; & DIFFUSERS

H25

Date: 2000

Part Number Female Pipe GPM Length Diam. Our Sequence Number Per Each

GRESEN Sump Filter - 100 Mesh - 149 Micron FST215-1TB 1-1/4 30 9-7/8 4-1/3 345535 $104.77 Flow Ezy All Metal 10-1-100 1 20-1-1/4-100 1-1/4 30-1-1/2-100 1-1/2 TANK-MOUNTED STRAINERS This is an easy way to put a strainer to work at your tank or reservoir. Mount them through the side wall, or through the top, into a standpipe. Either way they can be removed through the hole in which they are mounted, for easy servicing. Access to the tank interior is never necessary. Made in two styles: Suction line models are used when drawing fluid from the tank. Return line models are used when sending fluid into the tank.

Part Number Tank Bushing Female Pipe Our Sequence Number Per Each

Sump with Female Pipe 10 5-3/4 3-9/32 20 7-3/8 3-9/32 30 9-1/8 4-9/32 50 75 100 9-3/4 12-1/2 12-1/2 4-9/32 5-7/16 5-7/16

Threads 224880 224881 224882

38.83 45.50 75.83

50-2-100 75-2-1/2-100 100-3-100

2 2-1/2 3

224884 102.48 224886 135.11 224888 174.17

FLOW EZY ALL METAL SUMP STRAINERS WITH RELIEF SET AT 3 LBS. - 100 MESH 10-1-100-RV3 1 10 5-3/4 3-9/32 224920 20-1-1/4x100-RV3 1-1/4 20 7-3/8 3-9/32 224922 30-1-1/2-100-RV3 1-1/2 30 9-1/8 4-9/32 224924 50-2-100-RV3 75-2-1/2-100-RV3 100-3-100-RV3 2 2-1/2 3 50 75 100 9-3/4 12-1/2 12-1/2 4-9/32 5-7/16 5-7/16

45.96 52.16 90.99

GPM

Length

Diam.

S5-60 S10-60 S15-60 S25-60 R-19-100 R-33-100 R-54-100 R-94-100 D34 D55

1 1-1/4 1-1/2 2 1 1-1/4 1-1/2 2 1-1/4 1-1/2

SUCTION 1/2 3/4 1 1-1/4

STRAINERS - 60 MESH 5 5-5/16 7/8 10 8 1-1/8 15 8-1/2 1-1/4 25 9-9/16 1-9/16 MESH 7/8 1-1/8 1-1/4 1-9/16 1-1/8 1-1/4

224926 130.28 224928 159.93 224930 194.85

224580 $29.18 224582 35.39 224584 42.51 224588 48.71 224645 224655 224665 224675 224610 224620 29.18 35.39 41.13 48.71 48.02 49.86

FLOW EZY RETURN LINE DIFFUSER

Female Pipe Thread or Male Nipple Pipe Thread Screws on or screws in (nipple design).

RETURN FILTERS - 100 1/2 18 5-5/16 3/4 32 8 1 53 8-1/2 1-1/4 93 9-9/16 3/4 1 DIFFUSERS 34 8 55 8-1/2

Qty. Disc: 5 pkgs. 5%, 10 pkgs. 7%, 25 pkgs. 10%

Flow diffusers help to cure foaming problems & to prevent cavitation caused by flow disturbance at the pump inlet. These units allow greater freedom in reservoir design, and may even eliminate the need for tank baffling plates. They also reduce reservoir noise. All-steel construction, and may be ordered with nut or nipple connector.

Part Number Pipe Thread GPM Length Diam. Our Sequence Number Per Each

By assembling the pipe fittings listed in the table you build a housing into which the Flow Ezy strainer fits. D-33 Female DIMENSIONS AND SUPPLIES D-33 Nipple Strainer Assembled

Model Size Bushing Size Length Length (Approx.) Pipe Size

High Speed Return Line Flow Diffuser 3/4F 33 3-1/2 3-3/16 224850 $39.52 3/4M 33 4-5/16 3-3/16 224852 42.28 1F 1M 1-1/4F 54 54 94 5-3/8 6-9/16 7-3/16 3-3/16 3-3/16 3-3/16 224854 224856 224858 45.27 49.40 53.54

S-5 S-10 S-15 S-25

For Strainer Model

1 1-1/4 1-1/2 2

x x x x

1/2 3/4 1 1-1/4

5-5/16 8 8-1/2 9-9/16

7 10 11 13

1/2 3/4 1 1-1/4

D-54 Female D-54 Nipple D-94 Female Date: 3300

MAGNETIC DRAIN PLUGS

PLUMBING SUPPLIES REQUIRED

Nipple (1 Required) Coupling (2 Required) Bushing (1 Required)

S-5 S-10 S-15 S-25

1-1/4 1-1/2 2 2-1/2

x x x x

3-1/2 6 5-1/2 7

1-1/4 1-1/2 2 2-1/2

x x x x

1 1-1/4 1-1/2 2

1 1-1/4 1-1/2 2

x x x x

3/4 3/4 1 1-1/4

FLOW EZY SUMP STRAINER

Plugs are square head not hex head as pictured.

Size Inches Our Sequence Per Number Each | | Size Inches Our Sequence Number Per Each

Flow Ezy Sump Strainer with Male Pipe Threads

Part Number Male Pipe GPM Length Diam. Our Sequence Number Per Each

1/8 1/4 3/8 1/2 3/4

With Male Square head & Extended Magnet 146060 $3.62 | 1-1/2 146081 146063 3.69 | 2 146083 146066 4.55 | With Male Square head & Flush Magnet 146069 2.33 | 1 146075 146072 3.37 | 1-1/4 146078 146086 With Male Hex head 5.05 | 3/4-ORB 146092

$28.75 37.63

P-3 3/4-60 P-50-2 P-75-2-1/2 P-100-3

Nylon-End Nipple Style Flow Ezy Sump Strainer - 60 Mesh 3/4 3 3-5/8 2-1/8 2 50 11-1/4 4-3/16 2-1/2 75 13-3/4 5-3/16 3 100 13-3/4 5-3/16

9.63 15.65 7.48

224700 $20.45 224710 62.73 224720 70.31 224730 85.94

1/2-ORB

Plug Qty. Disc: 2 pkgs 2%; 5 pkgs. 5%; 10 pkgs. 10%; 25 pkgs. 15% Prices subject to change without notice

© 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

H26

1. Single-Acting Cylinders. The diagram below shows a hydraulic system with two single-acting cylinders and a two spool 3-way single-acting control valve. The control valve is located between the pump outlet and the cylinders. The relief valve is between the pump and the control valve. When the relief valve is built-in the control valve, the layout is the same except some of the lines are inside the control valve. The return-line filter is between the control valve and the tank, placed ahead of the tee between the return line and the relief valve return line or overflow. This is the safest place to put a filter. Tank should be at pump height or not more than 2 feet below pump for best results.

HYDRAULIC LAYOUTS How To Drive One Motor With One Pump

Best and Most Versatile System

No. 1 Use: To operate one motor in either directionreversible with four-way FREE-WHEELING control valve. Advantages: This system will give best results. Can start, stop, or reverse without stopping pump. Requires: One SPXT-F4 FREE WHEELING Control Valve.

2. Double-Acting Cylinders. The diagram below shows a hydraulic system with two double-acting cylinders and a two spool 4-way double-acting valve. The layout is the same as No. 1 above except for the return lines of the double-acting cylinders.

How to Drive One Motor With One Pump Where Motor Must Hold A Load When Power is Off

No. 4 Use: To operate one motor in either directionreversible with a standard four-way control valve without freewheeling and with two relief valves next to the motor acting as a cushion valve. Advantages: This system will hold a load in position when the pump or valve is shut off, as on a winch. Can be started, 3. Cylinders in Series. In diagram No. 2 the cylinders could stopped, or reversed while pump is operating. only be moved one at a time because they are set up in parallel operation using a two spool valve. When it is desirable Requires: Three K-100-HP RELIEF VALVES and one SP-4 to operate two cylinders at the same time, it is necessary to STANDARD Control Valve. attach two or more single spool 400 or 300 valves in SERIES How To Drive Two Motors With One Pump and put a separate relief valve ahead of the control valves. The following diagram shows this and shows the separate relief valve which is necessary to avoid pressure doubling even though relief valves are built into the control valves. A return line filter is used. Any single acting cylinders are put at the tank end of the system after the double-acting cylinders as shown.

Best and Most Versatile System

No. 2 Use: To operate two motors in either directionreversible where either motor can be operated or reversed separately or together, using two separate four-way FREEWHEELING control valves (not one two spool valve). 4. Two systems from one pump. Where you desire to operate two systems from one pump such as a backhoe and a Advantage: This system will give the best results for two loader on the same tractor, use a selector valve and the layout motors and one pump. Can stop or start or reverse either shown in the diagram on the Selector Valve page. This is very motor separately without stopping pump. useful where the two systems never operate at once. Uses How to Measure Output of a Pump S-50 or S-75 selector valve. 5. To Add a Cylinder to a System. Where you desire to add a double-acting cylinder to an existing double-acting cylinder, and use the same control valve for both, use a DS-75 double selector valve and the layout shown in the diagram at the bottom of the Selector Valve page under double selector valves.

© 2011 by Baum Hydraulics Corporation

If you are in doubt, measure diameter and thickness of gears, also length of gear chamber. Measure thickness of Vane Rotor Ring, length and width of oval inside RotorRing, and we can select a similar size pump from our stock.

Prices subject to change without notice

1-800-228-9222 www.baumhydraulics.com

Date: 2500

WIKA HYDRAULIC PRESSURE GAUGES

H27

1 2 3 4 5 6 7 8

Safety Blow-Out Disc Coiled Safety Bourdon Tube Cast Brass Case/Stainless Steel Case Black Aluminum Pointer Nickel-Silver Pinion Gear & Shafts Adjustable Linkage Precision Movement Window/Membrane Assembly

213.53 Made for use on hydraulic systems of tractors, backhoes, hydraulic motors, hydraulic pumps, presses, diesel engines and other similar apparatus where accurate indication of hydraulic pressure is essential. Gauges contain recalibrator. A gauge may need recalibration because normal wear and fatigue can eventually cause inaccuracies. To make an adjustment, simply release all pressure and turn recalibrating screw until point resets at zero.

111.10 WIKA gauges are produced to the highest manufacturing standards. For example, all 2-1/2" gauges, 800 PSI and higher, and most 4" and 6", 1500 PSI and higher, feature a coiled safety Bourdon tube. Now WIKA introduces its innovative new liquid filled gauges, incorporating both a pressureequalizing membrane and a new safety blow-out disc. Also offered is a solid front, blow-out back stainless steel gauge. WIKA liquid filled gauges are hermetically sealed and engineered for exceptional resistance to pulsation, corrosion, vibration and metal fatigue. In addition to such time proven design features as stress-equalizing coiled safety Bourdon tube construction, low-friction moving assemblies and resistance to internal temperature variation, these new liquid filled gauges offer first-in-the-industry improvements; an innovative safety blow-out disc to ensure operator safety, and a revolutionary pressure-equalizing membrane to maintain outstanding accuracy even in hostile environments. PSI & kPa

Size Fill

2-1/2" Gauge 1/4" NPT Oil Filled Stainless Steel Case

1.5% Single Our Sequence Number Per Each

| | |

| | | | 1.5% Dual

2-1/2" Gauge 1/4" NPT Dry Gauge Plastic Case

Our Sequence Number Per Each

| | |

| | | | 1.5% Single

4" Gauge 1/4" NPT Oil Filled Stainless Steel Case

Our Sequence Number Per Each

Accuracy Scale

LM - LOWER MOUNT 30 HG VAC 30 PSI 60 PSI 100 200 300 400 PSI PSI PSI PSI 213.53 213.53 213.53 213.53 213.53 213.53 213.53 213.53 213.53 213.53 213.53 213.53 213.53 213.53 587396 587397 587398 587399 587400 587401 587402 587403 587404 587405 587406 587407 587408 587409 $54.97 48.65 50.60 48.67 50.60 50.60 50.60 50.60 50.60 53.73 55.74 55.74 55.74 70.46 | | | | | | | | | | | | | | 111.10 111.10 111.10 111.10 111.10 111.10 ----111.10 ----111.10 ----111.10 111.10 ----587355 587356 587357 587359 587360 587361 587363 587365 587367 587368 $33.90 30.14 30.14 30.14 30.22 30.14 .... 30.14 .... 31.27 .... 33.12 41.61 .... | | | | | | | | | | | | | | --------------------------------------------213.53 213.53 213.53 587428 587429 587430 $.... .... .... .... .... .... .... .... .... .... .... 124.58 124.58 165.59

600 PSI 1000 PSI 1500 PSI 2000 PSI 3000 PSI 5000 PSI 10000 PSI

CBM - CENTER BACK MOUNT 30 PSI 400 PSI 1500 PSI 3000 PSI 5000 PSI --------213.53 213.53 213.53 587418 587420 587421 .... .... 54.11 55.58 57.71 | | | | | 111.12 111.12 111.10 111.12 ----5873725 587378 587384 587387 30.32 30.32 36.02 36.02 ....

Qty. Disc: 2 pkgs. 5%, 5 pkgs. 10%, 10 pkgs. 15%

PROMPT WAREHOUSE SERVICE. SAME DAY SHIPMENT

RETURN & SUCTION FILTER GAUGES for BAUM, GRESEN, PRINCE and CROSS FILTERS

Date: 2000 CI-20 For Baum, Gresen, Prince & Cross Filter 1/8" NPT Center Back Mount 2" Diameter Filter Gauge

Part Number Our Sequence No. Per Each

GV-10

CI-20

Return Filter Gauge-60 PSI 501360 $11.80

Suction Filter Gauge-30" HG Vacuum GV-10 501370 11.80 For use with 25 psi filter by-pass valve © 2011 by Baum Hydraulics Corporation Qty. Disc: 5 pkgs. 5%, 10 pkgs. 7% 1-800-228-9222 www.baumhydraulics.com For use with 5 psi filter by-pass valve Prices subject to change without notice

H28

USED ON:

HAYDEN HYDRAULIC OIL COOLERS

Date: 2500

HYDROSTATIC TRANSMISSIONS OFF-ROAD EQUIPMENT CONSTRUCTION EQUIPMENT CEMENT MIXER TRUCKS AGRICULTURAL EQUIPMENT TRUCK TRANSMISSIONS Cooler should have capacity to remove 30% of horsepower developed in system.

Bypass line may be added, provides temporary increased capacity and cold weather protection. Use C-1200S-65 check valve.

Hayden makes a wide variety of sizes and types of oil-to-air coolers. Regardless of the application - stationary or vehicular - there's a Hayden unit designed to deliver reliable cooling power. Hayden heat transfer capability is widely used as auxiliary cooling on existing equipment, as complete cooling replacements or as original equipment at the OEM stage. Any system that generates hot oils or viscous fluids needs Hayden "Cooling Power". 20 degrees of cooling doubles life of petroleum oils. Conversely,HEAT KILLS OIL - by more rapidly forming oxides, waxes, varnishes, and sludges. Heat volitizes additives. Heat reduces viscosity, causing bearing failures.

Our Sequence Number

Inner-Swirl Action is created by uniquely designed inner-swirl fins located inside the cooler tubes. As the hot oil flows through the swirl fins, hundreds of tiny "swirlpools" swirl clockwise and then counter-clockwise at precisely tooled spiral-grooved openings. This 360o swirling action assures double heat extraction by the double turn exposure of hot oil to the cold air side of the cooler.

Fitting Size FPT

STANDARD CAPACITY RATINGS TRANSCOOLERS

Model Number Per Each Cooling Cap. BTU/Hr. Max. GPM Height Outside Dimensions, Inches Length Width Unit Wt. Lbs.

1215 1240 1241 1268 1260 1290 1292 2305

190799 190801 190802 190806 190804 190808 190810 190814

$87.47 119.20 150.87 190.92 224.88 295.50 413.14 492.92

7,110 13,300 21,300 25,800 35,200 54,300 72,300 90,400

8 12 16 24 24 36 48 60

4 6 8 12 12 18 24 30

15 18 21 18 24 24 24 24

1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2

1/2 1/2 1/2 3/4 3/4 3/4 1 1

9 12 14 17 15 27 23 34

Qty. Disc: 2 pkgs. 15%, 5 pkgs. 22.5%

OIL SUPPLY TANKS

As a general recommendation you should not have a tank smaller than the GPM rating on your pump. For example: a ten gallon tank could take up to a 10 GPM pump. This would mean the oil would be completely changed each minute. The longer time the oil has to spend in the tank the more chance entrained air has of separating out and contamination particles have of setting. Ideally the tank should be above the pump and as close as possible to the pump to cut down on line resistance to flow. Chrome filler breather with basket strainer. Oil level gauge with temperature indicator. Interior baffle between suction and discharge. Large 2" NPT suction ports. Magnetic drain plug. Factory powder coated.

Part Number Gallon Capacity Tank Size Width x Height x Depth Our Sequence Number Per Each

SMR15S SMR25S SMR30S

15 25 30

19.58 x 17.5 x 14.5 22.35 x 20.0 x 16.0 28.35 x 22.0 x 17.0 Add 2.1 to heighth for fill

725001 725002 725003 capacity

$328.56 347.21 435.85

THREAD SIZE COMPARISON CHART

Tube Size Dash Size Pipe Thread 37 Deg. Female JIC O-Ring Straight Sealok Fore Seal Face Seal Ermeto 7000 Series Ermeto 8000 Series 45 Deg. Flare SAE Inverted Flare Compression Self-align Air Brake

1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2

2 3 4 5 6 7 8 10 12 14 16 20 24 32

1/8-27 -1/4-18 -3/8-18 -1/2-14 -3/4-14 -1-11-1/2 1-1/4-11-1/2 1-1/2-11-1/2 2-11-1/2

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 -3/4-16 7/8-14 1-1/116-12 1-3/16-12 1-5/16-12 1-5/8-12 1-7/8-12 2-1/2-12

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 -3/4-16 7/8-14 1-1/16-12 1-3/16-12 1-5/16-12 1-5/8-12 1-7/8-12 2-1/2-12

--9/16-18 -11/16-16 -13/16-16 1-14 1-3/16-12 -1-7/16-12 1-11/16-12 2-12 --

5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 -3/4-16 7/8-14 1-1/16-12 1-3/16-12 1-5/16-12 1-5/8-12 1-7/8-12 2-1/2-12

5/16-24 3/8-24 1/2-20 9/16-18 5/8-18 -3/4-16 15/16-16 1-1/16-16 1-3/16-16 1-5/16-16 1-5/8-16 1-7/8-16 2-1/2-12

5/16-24 3/8-24 7/16-24 1/2-20 5/8-18 11/16-16 3/4-16 7/8-14 1-1/16-14 ------

5/16-28 3/8-24 7/16-24 1/2-20 5/8-18 11/16-18 3/4-18 7/8-18 1-1/16-16 ------

5/16-24 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 11/16-20 13/16-18 1-18 -1-1/4-18 ----

--7/16-24 -17/32-24 -11/16-20 13/16-18 1-18 ------

© 2011 by Baum Hydraulics Corporation

1-800-228-9222 www.baumhydraulics.com

Prices subject to change without notice

Information

h01.indd

28 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

9534


You might also be interested in

BETA
Sukup Parts.xls
h01.indd
RWF E70-600 SPC-Oct 00