Read Manual_PSO_x.pdf text version

INSTRUCTION MANUAL

PARTS LIST POST HOLE DIGGER

AN EXCELLENT CHOICE The Post Hole Digger is a high quality product, the first one in Brazilian market, which is rendering great services to thousands of users in all Brazilian territory and abroad. The Post Hole Digger General characteristics: · · · · · Chassis in a rectangular profile highly resistant to bending. Very hard gearbox with hardened alloy straight gears assembled on conical bearings. Transmission through the CARDAN SHAFT connected to the tractor's plug Easy and fast connection in the gear's universal hydraulic system in 3 points of any agricultural tractor. Positioning system of auger.

Treat your Post Hole Digger well. The proper maintenance and use of genuine spare parts will assure you a good performance of the product. Make sure of it by following the instructions of this Instruction Manual, or consulting your CEMAG dealer when you need further information. Read now this Instruction Manual with attention and start working with your Post Hole Digger In the first work day you will certainly agree that you have made AN EXCELLENT CHOICE. CEMAG

1

WARRANTY CEMAG S/A, when delivering any of its products to its dealers, assures they have no defects on the material quality or the engineering project. The application of the Warranty herein is of the implement dealers' request, and the customer shall not claim the warranty straight to CEMAG. Any matter related to the grant of warranty benefits will be analyzed by CEMAG, upon the dealer request, according to the criteria and conditions bellow: 1. The product specified herein will be guaranteed by CEMAG for possible material or manufacture defects only to the first buyer, within six (6) months, from the delivery date, proved by the formal Bill of Sale. 2. Any components or fittings used in the CEMAG products manufacture that are not of its own production, are excluded from this warranty term. 3. The warranty Terms herein will be cancelled if the improper use of the product or the inobservance of the rules herein is proved. 4. Any changes or modifications in the product that were not accepted in writing by CEMAG will cause the automatic loss to the Warranty right. 5. The defective parts that are covered by this Warranty Term will be CEMAG exclusive property, and the dealers, as a proof of the replace shall immediately send them. 6. The eventual defects in the parts quality under this Warranty Term shall not be taken as a reason to terminate purchase and sale agreements or to compensations of any kind. NOTE: CEMAG S/A, regarding to is technology development and engineering policy is entitled to, at any time, change, modify or improve its products, which shall not constitute any liability to apply such improvements on its models manufactured before that.

2

SPECIFICATIONS TECHNICAL SPECIFICATIONS AUGER SPEED AT 540 rpm IN THE TRACTOR'S PLUG DIAMETER OF AUGER MOD. BP-9 (9") DIAMETER OF AUGER MOD. BP-12 (12") DIAMETER OF AUGER MOD. BP-18 (18") WEIGHT OF DIGGER WITHOUT AUGER WEIGHT OF AUGER BP-9 WEIGHT OF AUGER BP-12 WEIGHT OF AUGER BP-18 MAXIMUM DIGGING DEPTH

130 rpm 23 cm 31 cm 46 cm 126 kg 20 kg 27 kg 37 kg 1.00 m

3

INSTRUCTIONS FOR CONNECTING TO THE TRACTOR CONNECTING TO THE TRACTOR Before connecting the Digger, it is necessary to remove the telescopic arm from the third point and the traction bar of the tractor. Make as follows, according to Fig. 1 · · · · · · · Connect the set of trestle (A) to the arms of the tractor lift and put the catch pins. Connect the spear (B) into the place from where the telescopic arm of the third point was removed (C) through the catch pin that attaches the telescopic arm. Joint the sets: trestle and axle spear (D), washers and bracing. Assemble the spring (M) on the chassis (B) and on the basis (N) and then assemble the positioner (L) on the gearbox. Check if the flanges of the CARDAN SHAFT are positioned in the same lignin and put a flange with fast gear (F) at the tractor plug axle. The CARDAN SHAFT's flange of flat hole shall be connected to the smallest axle of the gear box (G) and attached with a screw, nut and washer (H). Fit the auger in the bigger axle of the gear box (I) and catch it with the screw, nut and washer (J).

4

5

IMPORTANT Before fitting the CARDAN SHAFT in the Digger and tractor, the grafting of the telescopic axle shall be at the same plan and the grafting of the PTO gloves and gear box shall be in another plan moved to 90º related to the last one, keeping a perfect balance of the cardan (refer to the picture bellow). The purpose of this inspection is to avoid the cardan to work not balanced with the consequent breakage of the crossheads and the cardan itself. ATTENTION: THE FLANGES SHALL BE LIGNED UP.

AUGERS The augers are available in four different models: MODEL BP-9 BP-12 BP-18 DIAMETER 23 cm (9") 31 cm (12") 46 cm (18")

The augers have a double spiral, which makes the preparation of 60 to 100 holes per hour possible, at a maximum depth of 1.00 m. Some cares shall be taken to always keep the auger in the vertical position, during the operation term, for avoiding damages to the set and to make the work easier. The hole shall be completed in 2 or 3 stages and NEVER IN ONE ONLY TURN, avoiding the overload to the Digger and the tractor, and getting a better work development. MAINTENANCE GEARBOX: Check the oil level daily and complete it, if necessary. Replace the oil every 1500 hours of operation, using mineral oil SAE 140. GEAR TREE: Grease the crossheads and the intermediate sliding part daily with grease made with "Molybdenum". Check the crossheads play from time to time. If there is an outstanding abrasion, replace them.

6

AUGERS:

Check the state of the blades and heads from time to time and replace them in case of an outstanding abrasion. Check and tight the blade's screws. Loosen screws are the biggest causing of damages to the knives and to the tips of the spirals, and they also cause the auger outstanding vibration and the imperfection in the holes final touch. - Do not carry your Digger connected to the tractor with the plug on. - Avoid people standing close to the digging area - When checking any of the Digger's components, make sure the plug is off. - If you feel an outstanding resistance during the digging work, do not go on until you relieve the auger and/or eliminate any other possible cause. - Do not make holes deeper than the recommended depth - Do not make holes in lands with an outstanding declivity. - Lock the tractor's break well before you start the hole.

SPECIAL CARE:

7

GEAR TREE

8

1- GEAR TREE

ITEM 1 2 3 4 5 6 6A 7 8 9 CODE 299110 299169 299327 299686 299170 299340 299248 299339 299224 299182 DESCRIPTION COMPLETE CARDAN FEMALE CARDAN WITH FAST GEAR FEMALE CARDAN WITH CROSSHEAD CROSSHEAD FLANGE WITH COMPLETE FAST GEAR SET OF PIN, SPRING AND WASHER SET OF PIN, SPRING AND ELASTIC PIN (the old one) MALE CARDAN WITH SIMPLE FLANGES MALE CARDAN WITH CROSSHEAD SIMPLE FLANGES QUANTITY 01 01 01 02 01 01 01 01 01 01

9

TURRET AND CHASSIS

10

2) TURRET AND CHASSIS ITEM 1 2 3 4 5 6 7 8 CODE 409650 433950 412211 222288 491275 405565 428036 443130 DESCRIPTION CHASSIS AXLE OF THE BOX ARTICULATION FLAT WASHER Ø1" COUNTERPIN Ø5/16"x2" NUT Ø1.1/8" UNF (special) TURRET AXLE OF THE TURRET ARTICULATION GEAR PIN QUANTITY 01 01 04 04 02 01 01 02

11

GEAR BOX

12

3- GEAR BOX ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 CODE 419126 481336 288615 238399 497265 275128 284336 493818 456081 212350 259652 258090 412132 495281 260370 292011 419138 212301 497319 400063 284233 481397 274288 289188 460023 433962 459185 490647 456070 212430 258507 260599 493820 274203 494069 487697 487960 487983 DESCRIPTION COMPLETE GEAR BOX WEDGE SHIM 0.2x64 BEARING REF. 25577/522 SPRING OF POSITIONER" SEX. SCREW Ø1/4"x1/2" UNC ZINC PARLOCK NUT M40x1.5 RETAINER REF. 00284 BR JUNCTION REF. 12018 0.8 mm SIDE CAP PRESSURE WASHER Ø5/16" SEX. SCREW Ø7/16"x3.1/2" ZINC. 8.8 SEX. SCREW Ø5/16"x3/4" UNC SPECIAL FLAT WASHER SEX. NUT Ø7/16" UNC. ZINC. SEX. SCREW ½"x1" INC 8.8 GALV. VATS Ø1/2" BSP CARCASS REF. 12014 PRESSURE WASHER SEX. SCREW Ø1/2"x1.1/2" UNC. ZINC. CARCASS EAR RETAINER REF. 00051 BR WEDGE SHIM 0.3x96 SEX. NUT Ø5/8" UNF BEARING REF. 3984/20 TOP AXLE FOR GEAR BOX LOCK WIRE (500 mm) SCREW FOR ATTACHING THE TOP CARCASS CAP PRESSURE WASHER Ø7/16" SEX. SCREW Ø7/16"x1.1/4" UNC. SEX. SCREW Ø5/8"4.1/2" UNF 8.8 JUNCTION REF. 12017 0.4mm SEX. NUT Ø3/4" UNC PINE NUT WITH 12 TEETH POSITIONER STRETCHER SCREW ROT/PSO SPRING ATTACHER POSITIONER QUANTITY 01 02 03 01 01 01 01 02 01 04 01 04 01 01 01 02 01 06 06 02 01 02 01 01 01 01 01 12 01 08 08 01 01 01 01 01 01 01

13

AUGERS

14

4- AUGERS ITEM 1 CODE 403013 408025 408037 427172 427184 427196 407616 407628 407630 408001 212430 260368 495281 DESCRIPTION COMPLETE AUGER COMPLETE AUGER COMPLETE AUGER AUGER BODY AUGER BODY AUGER BODY KNIFE KNIFE KNIFE POINTER PRESSURE WASHER Ø7/16" SEX. SCREW Ø7/16"x1.1/4" UNC SEX. NUT Ø7/16" UNC B P-9" 01 01 02 01 04 04 04 BP-12" 01 01 02 01 04 04 04 BP-18" 01 01 02 01 06 06 06

2

3 4 5 6 7

15

CEMAG S.A. ­ MAIN OFFICE Av. Gaudioso de Carvalho, 217 ­ Jd. Iracema CEP 60.340-190 ­ FORTALEZA ­ CEARÁ PHONE/FAX: (+5585) 3228-2377 Site: www.cemag.com.br E-mail: [email protected]

CEMAG S.A. ­ COMMERCIAL OFFICE Av. Imperatriz Leopoldina, 1261 CEP 05305-012 ­ SÃO PAULO ­ SP PHONE: (+5511) 3644-7880 FAX: (+5511) 3832-2670 E-mail: [email protected]

Information

17 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

1282949