Read TM_9-4940-539-14_P.pdf text version

TM 9-4940-539-14&P

TECHNICAL MANUAL

OPERATOR'S, ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL INCLUDING REPAIR PARTS LIST

FOR

PRESS, HYDRAULIC MODEL H200-14 (NSN 4940-00-273-1653) NUGIER COMPANY

This publication is a courtesy quick copy from the UNITED STATES ARMY PUBLICATIONS CENTER, ST. LOUIS, MISSOURI, to meet your needs while we are replenishing our regular stock.

HEADQUARTERS, DEPARTMENT OF THE ARMY OCTOBER 1981

TM 94940-539-14&P Technical Manual No. 9-4940-539-14&P HEADQUARTERS DEPARTMENT OF THE ARMY Washington, DC, 23 October 1981

OPERATOR'S, ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL INCLUDING REPAIR PARTS LIST FOR PRESS, HYDRAULIC MODEL H200-14 (NSN 4940-00-273-1653)

REPORTING OF ERRORS You can help Improve this manual. If you find any mistakes or If you know of a way to improve the procedures, please let us know. Mail your letter, DA Form 2028 (Recommended Changes to Publications and Blank Forms), or DA Form 2028-2, located in the back of this manual direct to: Commander, US Army Armament Materiel Readiness Command, ATTN: DRSAR-MAS, Rock Island, IL 61299. A reply will be furnished directly to you.

NOTE This manual is published for the purpose of identifying an authorized commercial manual for the use of the personnel to whom this equipment is issued. Manufactured by: Nugier Company 12901 Coral Tree Place LosAngeles, CA90066 Procured under Contract No. DAA09-79-M-8457

This technical manual is an authentication of the manufacturers' commercial literature and does not conform with the format and content specified in AR 310-3, Military Publications. This technical manual does, however, contain available information that is essential to the operation and maintenance of the equipment.

i /(ii blank)

TM 94940-539-14&P INSTRUCTIONS FOR REQUISITIONING PARTS NOT IDENTIFIED BY NSN

When requisitioning parts not identified by National Stock Number, it is mandatory that the following information be furnished the supply officer. 1 - Manufacturer's Federal Supply Code Number - 94417 2 - Manufacturer's Part Number exactly as listed herein. 3 - Nomenclature exactly as listed herein, including dimensions, if necessary. 4 - Manufacturer's Model Number - H200-L]4 5 - Manufacturer's Serial Number (End Item) 6 - Any other information such as Type, Frame Number, and Electrical Characteristics, if applicable. 7 - If DD Form 1348 is used, fill in all blocks except 4, 5, 6, and Remarks field in accordance with AR 725-50. Complete Form as Follows: (a) In blocks 4, 5, 6, list manufacturer's Federal Supply Code Number ______followed by a colon and manufacturer's Part Number for the repair part. (b) Complete Remarks field as follows: Noun: (nomenclature of repair part) For: NSN: 494o-o0-273-l653 Manufacturer: Nugier Company 12901 Coral Tree Place Los Angeles, CA 90066 Model: H'200-14 Serial: (of end item) Any other pertinent information such as Frame Number, Type, Dimensions, etc.

OPERATING INSTRUCTIONS & PARTS MANUAL MODEL________ SERIAL_________ This manual coven models H40, H50, H60, H80, HI 00, HI 50, and H200 presses. When ordering parts or correspondence about these presses, always give the model number and serial number of the press. The Company manufactures not only the H40, H50, H60, H80, Hi 00, H1 50, and H200 model presses, but also larger and smaller sizes. The numbers designate the tonnage. All sizes are available in either hand pumped, air hydraulic driven, or motor driven models. We also manufacture a variety of bearing removal fixtures, as well as a fixture and tools for removing and replacing broke drums. The above mentioned tools are designed for use in conjunction with a hydraulic press. TABLE OF CONTENTS Page FOREWORD ......................................................................................... 1 A. PREPARING PRESS FOR SERVICE ............................................ 2 B. EXPLANATION OF HYDRAULIC CIRCUIT AND OPERATION OF CONTROLS ............................................... 2 C. TO PERFORM A PRESS OPERATION ......................................... 2 D. CYLINDER RAM TRAVEL.............................................................. 3 E. CAUTION........................................................................................ 3 F. HOW THE PUMP WORKS ........................................................... 3 G. TWO SPEED PUMP ACTI ............................................................. 3 H. CYLINDER CONTROL VALVE ...................................................... 3 I. CONTROL VALVES ....................................................................... 3 J. ADJUSTING VALVE STEM CLEARANCE..................................... 5 K. PRESS CYUNDER......................................................................... 5 L. MOVABLE CYLINDER ................................................................... 5 M. CYUNDER PRESSURE GAUGE ................................................... 6 N. TABLE WINCH ............................................................................... 6 O. CAUSES AND CURES OF TROUBLES IN HYDRAUUC PUMP CIRCUIT.................................................... 6 P. LOSS OF PRESSURE FROM PRESS CYUNDER........................ 7

PRESS SCHEMATICS HYDRAULIC SCHEMATIC CIRCUIT.................................................... 4 TABLE WINCH...................................................................................... 8 FRAME ASSEMBLY.............................................................................. 9 CYLINDER ASSEMBLY....................................................................... 10 PUMP UNIT.......................................................................................... 11 TANK INTERIOR ................................................................................. 12

1

Information

4 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

126704


You might also be interested in

BETA
Chapter 7 Recall Procedures
SBB-vers3_en.fm
Microsoft Word - 0900aecd805a6e73_null_null_null_06_03_04.docpdf