Read ENGLISH_TRIF_21e_100105 text version

Electric Motors

Asynchronous three-phase motors

2.1e

Technical Catalogue

2005

All technical data, outputs, dimensions and weights stated in this catalogue are subject to change without prior notice. The illustrations are not binding.

AEG Electric Motors - 2.1 e/2005 - page 2

C. . . .t . . . o.n.t.e.n . .s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page

Standard quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Standards and regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Conditions of installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Permissible temperature rises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mechanical design Degrees of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Mounting arrangements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Terminal boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Paint finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Lubrication and maintenance of bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Lubricating nipples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Anti-condensation heater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Electrical design Rated voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Rated frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Rated current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Rated torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Connection diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Insulation and temperature rise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Starting rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Thermal protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Three-phase cage motors driven by frequency converter . . . . . . . . . . . . . . . . . 31 Order data Motors for normal duty and conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Additional information for special designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Special service duties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Type designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

AEG Electric Motors - 2.1 e/2005 - page 3

AEG Electric Motors - 2.1 e/2005 - page 4

S .a . . a . d ... . . .t . .n.d. . r . . . Q u.a.l.i.t.y. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The strictness of our quality control assures the flawless operation and reliability of our products. That our quality scale fulfils your demands is confirmed by the certificate awarded by the TÜV-CERT Certification body of TÜV Rheinland and the CERMET, a Certification body authorized by SINCERT.

AEG Electric Motors - 2.1 e/2005 - page 5

S.t a.n.d . .r d s . . . n.d. .r.e.g . . l a.t i o.n.s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . a .... a . . . .u .. ... . .

CE Marking

Our three-phase induction motors comply with the requirements of the following international standard: IEC 60034 as well as with the Low Voltage Directive 73/23 (1973), modified by the Directive 93/68 (1993) and the EMC-Directive 89/336. The above named products comply with the requirements of the EC Directive Machines 89/392. In accordance with this Directive induction motors are components and intended solely for integration into other machines. Commissioning is forbidden until conformity of the end product with this Directive is proved!

The

symbol was applied for the first time in 1995.

The safety instructions in the Operation Manual of the manufacturer and EN 60204-1 have to be observed.

CEMEP Voluntary Agreement

Motors covered by this agreement are defined as totally enclosed fan-cooled (normally IP 54 or IP 55), three-phase AC squirrel cage induction motors 1.1 to 90 kW, with 2 or 4 poles, rated for 400 V-line, 50 Hz, duty class S1. (Standard design can be interpreted as design N according to EN 60034-12 and HD 231). They are divided in three classes of efficiency levels, defined by 2 values of full load efficiency per output, designated eff1, eff2 and eff3.

All motors with standard rating included in this catalogue comply with efficiency class eff2 and bear the corresponding label on the rating plate. For efficiency data at 50%, 75% and full load, please refer to the electrical data tables.

AEG Electric Motors - 2.1 e/2005 - page 6

The motors comply with the relevant standards and regulations, especially:

Títle IEC Electrical General stipulations for electrical machines Rotating electrical machines: methods for determining losses and efficiency using tests Terminal markings and direction of rotation of rotating electrical machines Starting performance Standard voltages Insulating materials Mechanical Dimensions and output ratings Mounting dimensions and re- 60072 lationship frame sizes-output ratings, IM B3 Mounting dimensions and re- 60072 lationship frame sizes-output ratings, IM B5 Mounting dimensions and re- 60072 lationship frame sizes-output ratings, IM B14 Cylindrical shaft ends for electric motors Degrees of protection Methods of cooling Mounting arrangements Noise limits Mechanical vibration Mounting flanges Tolerances of mounting and shaft extensions Classification of environmental conditions Mechanical vibration; balancing ISO 8821 DIN ISO 8821 600721-2-1 60034-5 60034-6 60034-7 60034-9 60034-14 EN 60034-5 EN 60034-6 EN 60034-7 EN 60034-9 DIN EN 60034-5 DIN EN 60034-6 DIN EN 60034-7 DIN EN 60034-9 DIN 42948 DIN 42955 CEI EN 60034-5 CEI EN 60034-6 CEI EN 60034-7 CEI EN 60034-9 UNEL 13501 UNEL 13501/ 13502 DIN IEC 60721-2-1 CEI 75-1 4999-20 EN60034-5 20111-5 4999-21 4999-22 51-117 4999-51 51-119 EN 60034-6 EN 60034-7 EN 60034-9 EN 60034-14 60072 HD 231 DIN 748-3 UNEL 13502 4999-10 51-111 DIN 42677-1 UNEL 13118 4999-10 51-105 51-110 51-104 UNE EN 50347 DIN 42677-1 UNEL 13117 20106-2-74 DIN 42673-1 UNEL 13113 4999-10 51-105 51-110 51-104 UNE EN 50347 1980 60072 DIN EN 50347 UNEL 13113 60034-12 60038 60085 EN 60034-12 DIN EN 60034-12 CEI EN 60034-12 4999-112 HD 472 S1 DIN IEC 60038 DIN IEC 60085 CEI 8-6 CEI 15-26 UNE EN 60034-12 60034-8 HD 53 8 S4 DIN VDE 0530-8 CEI 2-8 4999-3 51-118 20113-8-96 60034-2 HD 53 2 DIN EN 60034-2 CEI EN 60034-2 60034-1 EN 60034-1 DIN EN 60034-1 CEI EN 60034-1 4999-1 51-200 UNE EN 60034-1 UNE EN 60034-2 4999-69 51-111 4999-34 51-112 EU CENELEC D DIN/VDE I CEI/UNEL GB BS F NFC E UNE

EN60034-14 DIN EN 60034-14 CEI EN 60034-14 4999-50 51-111

Motors to special regulations:

· Motors to VIK regulations (German Society for Industrial Energy and Power Stations) to VIK recommendation Technical Requirements April 1999 · Motors with UL and/or CSA approval (performance data on request) · Motors with CULUS (CURUS) approval The motors can furthermore be designed according to the stipulations for floating installations of the most important classification societies. For further details see our technical catalogue Three-phase motors for marine applications.

AEG Electric Motors - 2.1 e/2005 - page 7

C. . . . . o.n.d.i.t.i.o.n . . .o.f. .i.n.s t . .l l a.t.i o.n. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .s . . .. a ... .. .

The motors are designed for operation at altitudes 1000 m above sea-level and at ambient temperatures of up to 40° C. Exceptions are indicated on the rating plate.

Permissible temperature rises to various standards

Standard/Regulation Temperature of coolant °C VDE 0530 part 1 International IEC 34-1 Britain BS 2613 Canada CSA USA NEMA and ANSI Italy CEI Sweden SEN Norway NEK Belgium NBN France NF Switzerland SEV India IS Germanischer Lloyd 1) American Bureau of Shipping 1) Bureau Veritas 1) Norske Veritas

1)

Permissible temperature rise in K (measured by resistance method) Temperature class B F H 80 80 80 80 80 80 80 80 80 80 80 80 75 70 70 70 70 70 70 75 105 105 105 105 105 105 105 105 105 105 105 90 95 100 90 2) 90 90 90 95 125 125

40 40 40 40 40 40 40 40 40 40 40 40 45 50 45 45 45

1)

on request

Lloyds Register 1) Registro Italiano Navale Korean Register

1)

45 50 45

China Classification Society 1)

1)

Classification societies for marine motors Only with special approval

2)

AEG Electric Motors - 2.1 e/2005 - page 8

The motors conform to degree of protection IP 55 to IEC 60034-5. Higher protection on request. The standard design for horizontal mounting is suitable for indoor and protected outdoor installation, climate group MODERATE (see page 15) (temperature of coolant -20° to +40° C). For unprotected outdoor installation or severe climatic conditions (moisture category wet, climate group WORLDWIDE, extremely dusty site conditions, aggressive industrial atmosphere, danger of storm rain and coastal climate, danger of attack by termites, etc.), as well as vertical mounting, special protective measures are recommended, such as: · · · · · · Protective cowl (for vertical shaft-down motors) For vertical shaft-up motors additional bearing seal and flange drainage Special paint finish Treatment of winding with protective moisture-proof varnish Anti-condensation heating (possibly winding heating) Condensation drain holes

The special measures to be applied have to be agreed with the factory once the conditions of installation have been settled.

The corresponding conditions of installation have to be clearly indicated in the order.

AEG Electric Motors - 2.1 e/2005 - page 9

Tolerances

For industrial motors to EN 60034-1, certain tolerances must be allowed on guaranteed values, taking into consideration the necessary tolerances for the manufacture of such motors and the materials used. The standard includes the following remarks: 1. It is not intended that guarantees necessarily have to be given for all or any of the items involved. Quotations including guaranteed values subject to tolerances should say so, and the tolerances should be in accordance with the table. 2. Attention is drawn to the different interpretation of the term guarantee. In some countries a distinction is made between guaranteed values and typical or declared values. 3. Where a tolerance is stated in only one direction, the value is not limited in the other direction. Values for Efficiency () (by indirect determination) Power factor (cos ) Slip (s) (at rated load and at working temperature) Breakaway starting current (IA) (in the starting circuit envisaged) Breakaway torque (MA) Pull-up torque (MS) Pull-out torque (MK) Moment of inertia (J) Tolerance - 0.15 (1 - ) at PN 50 kW - 0.1 (1 - ) at PN > 50 kW 1 - cos 6 , minimum 0.02, maximum 0.07

± 20 % of the guaranteed slip at PN 1 kW ± 30 % of the guaranteed slip at PN < 1 kW + 20 % of the guaranteed starting current (no lower limit) - 15 % and + 25 % of the guaranteed breakaway torque (+ 25 % may be exceeded by agreement) - 15 % of the guaranteed value - 10 % of the guaranteed value (after allowing for this tolerance, MK/MN not less than 1.6) ± 10 % of the guaranteed value

Mechanical tolerances

According to IEC 72-1, the following tolerances on mechanical dimensions of electric motors are permitted: Parameter Shaft length Code H Tolerances up to 250 over 250 from 11 to 28 mm from 38 to 48 mm from 55 to 100 mm -0,5 mm -1 mm j6 k6 m6 h9 j6 h6

Diameter of shaft end Hub key width Flange spigot

D-DA F-FA N

- up to 132 - over size 132

Note: The holes at the shaft end conform with DIN 332

AEG Electric Motors - 2.1 e/2005 - page 10

M . c . .n .. a . . . .. . . . .e . .h.a . .i c. . l . d.e.s.i g.n. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Degrees of protection

Degrees of protection for mechanical machines are designated in accordance with IEC 60034-5 by the letters IP and two characteristic numerals.

First numeral: Protection against contact and ingress of foreign bodies IP 0 1 Description No special protection Protection against solid foreign bodies larger than 50 mm (Example: inadvertent contact with the hand) Protection against solid foreign bodies larger than 12 mm (Example: inadvertent contact with the fingers) Protection against solid foreign bodies larger than 2.5 mm (Example: Wires, tools) Protection against solid foreign bodies larger than 1 mm (Example: Wires, bands) Protection against dust (harmful deposits of dust)

Second numeral: Protection against ingress of water IP 0 1 Description No special protection Protection against vertically falling water drops (condensation)

2

2

Protection against dropping water when inclined by up to 15°

3

3

Protection against waterspray at up to 60° from vertical

4

4

Protection against water splashed from any direction

5

5

Protection against water projected by a nozzle from any direction Protection against heavy seas or water projected in powerful jets

6

Complete protection against dust. Is not described for electrical machines to IEC 34-5.

6

7

Protection when submerged between 0.15 and 1 m

8

Protection when continuously submerged in water at conditions agreed between the manufacturer and the user.

AEG Electric Motors - 2.1 e/2005 - page 11

Mounting arrangements

Mounting arrangements for rotating electrical machines are designated according to IEC 60034-7, Code I (in brackets Code II). Our motors are available with the mounting arrangements listed below, depending on design and frame size. Motors with aluminium frame are equipped with removable feet that allow easy change of mounting arrangement.

Foot mounting

IM B3 (IM 1001)

Flange mounting

IM B5 (IM 3001) Flange type A to DIN 42 948 at drive end

Motors without endshield

IM B9 (IM 9101) without endshield and without ball bearings on drive end

IM B6 (IM 1051) *

IM V1 (IM 3011)

Flange type A to DIN 42 948 at drive end

IM V8 (IM 9111)

without endshield and without ball bearings on drive end

IM B7 (IM 1061) *

IM V3 (IM 3031)

Flange type A to DIN 42 948 at drive end

IM V9 (IM 9131)

without endshield and without ball bearings on drive end

IM B8 (IM 1071) *

IM B35 (IM 2001)

Flange type A to DIN 42 948 at drive end

IM B15 (IM 1201)

without endshield and without ball bearings on drive end

IM V5 (IM 1011) *

IM B14 (IM 3601)

Flange type C to DIN 42 948 at drive end

IM V6 (IM 1031) *

IM V18 (IM 3611)

Flange type C to DIN 42 948 at drive end

IM B34 (IM 2101)

Flange type C to DIN 42 948 at drive end

IM V19 (IM 3631)

Flange type C to DIN 42 948 at drive end

* From frame size 225 on request

It is essential to state the desired mounting arrangement when ordering, as the constructive design depends partly on the mounting arrangement.

AEG Electric Motors - 2.1 e/2005 - page 12

Terminal boxes

The location of the terminal box in standard design is on top; on the right or on the left are possible. For motors with mountings IM B6, IM B7, IM B8, IM V5, IM V6 the location of the terminal box is related to an IM B3 mounting. The position of the entry openings can be adjusted to suit the existing connection facilities by turning through 90°. Should special accessories be used (temperature detectors, anti-condensation heating, etc.) please enquire. For motors in standard design, the cable gland does not belong to our scope of delivery. For plastic terminal boxes, only plastic glands may be used (shock protection). When using screened leads, a metal terminal box is required. Direction of cable entries

Frame size

Degree of protection

Thread for cable entry Pg 1) 1 x Pg 11 x Pg 13.5 1 x Pg 13.5 x Pg 16 1 x Pg 13.5 x Pg 16 2 x Pg 21 2 x Pg 29 2 x Pg 29 2 x Pg 36 2 x Pg 36 2 x Pg 42 2 x Pg 48 3) Metric 2) 1 x M16 x M20 1 x M25 x M20 1 x M25 x M20 2 x M32 2 x M40 2 x M40 2 x M50 2 x M50 2 x M63 2 x M63 3)

Connection for temperature detector Pg 1) Metric

-

Max. cable section

2)

Terminal thread

Max. external cable diam. mm 12 16 16 20 28 28 34 34 40 48

56 - 71 80 90-112 132 160 180 200 225 250 - 280 315

IP IP IP IP IP IP IP IP IP IP

55 55 55 55 55 55 55 55 55 55

Pg 11 Pg 13.5 Pg 16 Pg 16 Pg 16 2 x Pg 16

M20 M20 M25 M25 M25 M25

mm 2 2.5 2.5 4 4 16 35 35 50 50 185

M4 M4 M5 M5 M6 M8 M8 M10 M10 M12

Pg thread to DIN 40 430 Pitch 1.5 3) Terminal box with unscrewable cable entry plate

1) 2)

AEG Electric Motors - 2.1 e/2005 - page 13

g4

g4

B

B

Terminal box on top

h

Terminal box at the side

h

A

left

1)

right

Frame size h

g4

A

B

Design

Material

Frame size h Special design

g4

A

B

Design

A

Material

Standard design 56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 98 103 112 129 138 145 161 198 246 266 341 360 390 423 515 91 91 91 111 111 111 111 133 149 204 258 258 258 258 400 93 93 93 116 116 116 116 133 149 180 265 265 265 265 285 Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z K K K K K K K AL AL SB SB SB SB SB GG

2) 2) 2) 2)

56 63 71 80 90 100 112 132 160 180 200 225 250 280

100 105 114 139 148 155 171 205 250 285 310 334 375 409

94 94 94 110 110 110 110 143 168 209 241 272 272 272

94 94 94 110 110 110 110 143 168 220 246 254 254 254

Z Z Z Z Z Z Z Z Z Z Z Z Z Z

AI AI AI AI AI AI AI GG GG GG GG GG GG GG

Special design gland cover 56 63 71 80 90 100 112 132 160 180 200 225 250 280 64 69 78 125 137 141 154 183 225 250 280 300 340 375 70 70 70 91 91 91 91 111 130 144 172 172 208 208 70 70 70 91 91 91 91 111 130 144 172 172 208 208 E E E E E E E E E E E E E E K K K AI AI AI AI GG GG GG GG GG GG GG

3) 3) 3) 3)

3) 3) 3)

1)

On frame size 56-71 the terminal box is supplied displaced towards the non-drive end 2) For metric thread, increase g4 by 6mm 3) Maximum height with screw joint

Design: E = Single part Z = Two parts

Material: K SB AL GG

= = = =

Plastics Sheet steel Aluminium Cast iron

AEG Electric Motors - 2.1 e/2005 - page 14

Materials

Motor parts Stator frame Frame size 56 - 180 132 - 180 225 - 315 Endshield Flanged endshield Fan cover 56 - 112 132 - 315 56 - 112 132 - 315 56 - 63 71 - 112 80 - 112 132 - 315 Fan Terminal box 56-315 56 - 112 56 - 112 132 - 160 180 - 280 + 315SY 315 Material Aluminium alloy Cast iron (optional) Cast iron Aluminium alloy Cast iron Aluminium alloy Cast iron Sheet steel Plastics Sheet steel (optional) Sheet steel Plastics Plastics Aluminium alloy (optional) Aluminium alloy Sheet steel Cast iron

Paint finish Normal finish

Suitable for climate group Moderate to DIN 600 721-2-1, e.g. indoor and outdoor installation for short periods: up to 100 % rel. humidity at temperatures up to +30° C continuously: up to 85 % rel. humidity at temperatures up to +25° C

Special finish K1

Suitable for climate group Worldwide to DIN 600 721-2-1, e.g. outdoor installation in corrosive chemical and marine atmospheres for short periods: up to 100 % rel. humidity at temperatures up to +35° C continuously: up to 98 % rel. humidity at temperatures up to +30° C

Special finishes (on request)

· Special finish K2 (additional treatment of internal motor parts) · Special paint for exposure to the action of alkalis · Special finishes to customers' requirements

AEG Electric Motors - 2.1 e/2005 - page 15

Bearings

Classification of bearings (standard design) Ball bearings to ISO15 (DIN 625) Frame size No. of poles 2+4 2+4 2-8 2-8 2-8 2-8 2-8 2-8 Drive end

1)

Non-drive end

Frame size

No. of poles 2 2 2 2 2 2 -8 -8 -8 -8 -8 -8 2 4-8 4-8

Drive end

Non-drive end

56 63 71 80 90 100 112 132

1)

6201-2Z 6202-2Z 6202-2Z 6204-2Z C3 6205-2Z C3 6206-2Z C3 6306-2Z C3 6208-2Z C3

6201-2Z 6202-2Z 6202-2Z 6204-2Z C3 6205-2Z C3 6206-2Z C3 6306-2Z C3 6208-2Z C3

160 2) 180 200 225 250 280 315 315SY

6209-2Z C3 6210-2Z C3 6212-2Z C3 6213-Z C3 6214 C3 6216 C3 6316 C3 6319 C3 6319 C3

6209-2Z C3 6210-2Z C3 6212-2Z C3 6213-Z C3 6214 C3 6216 C3 6316 C3 6319 C3 6316 C3

2)

In frame sizes 132 to 280 bearings type 63 also possible at drive and non-drive end (preferably locating bearing non-drive end), or bearings NU 3 at drive end in frame sizes 160 to 280 (only locating bearing at non-drive end). IM B14 bearing drive end 6309-2Z C3

Bearing arrangement (AM, AMV)

Frame size 56 - 112 132 - 280 315 Bearing drive end Non-locating bearing Locating bearing Non-locating bearing Bearing non-drive end Non-locating bearing Non-locating bearing Locating bearing Spring-loaded Non-drive end Non-drive end Drive end

Maximum permissible axial forces without additional radial forces *

Frame size 3000 min -1 kN 0.16 0.19 0.23 0.32 0.34 0.48 0.48 0.6 0.5 0.5 0.8 1.0 1.1 1.7 3.5 Horizontal shaft 1500 1000 min -1 min -1 kN kN 0.21 0.26 0.33 0.44 0.48 0.68 0.68 0.9 0.8 0.8 1.3 1.6 1.6 1.9 4.0 0.33 0.46 0.49 0.70 0.70 1.1 1.2 1.2 1.5 1.9 2.0 2.4 4.5 750 min -1 kN 0.37 0.50 0.54 0.77 0.77 1.3 1.5 1.5 1.8 2.4 2.5 2.9 5.0 Vertical shaft - force upwards 3000 1500 1000 750 min -1 min -1 min -1 min -1 kN kN kN kN 0.18 0.21 0.26 0.34 0.38 0.54 0.56 1.0 1 1.1 1.8 2.1 2.3 2.9 6.0 0.22 0.28 0.35 0.47 0.47 0.74 0.75 1.3 1.4 1.4 2.3 2.6 2.7 3.1 7.0 0.36 0.48 0.53 0.76 0.77 1.5 1.8 1.8 2.5 2.9 3.2 3.6 7.5 0.39 0.53 0.58 0.83 0.84 1.9 2 2.1 2.8 3.4 3.7 3.7 8.0 Vertical shaft - force downwards 3000 1500 1000 750 min -1 min -1 min -1 min -1 kN kN kN kN 0.15 0.17 0.21 0.29 0.31 0.43 0.40 0.5 0.2 0.2 0.2 0.3 0.2 0.15 1.0 0.19 0.24 0.30 0.41 0.44 0.62 0.60 0.75 0.4 0.4 0.7 0.70 0.60 0.3 1.9 0.31 0.43 0.46 0.64 0.62 0.75 0.6 0.6 0.9 1.0 1.1 0.8 2.4 0.34 0.47 0.51 0.71 0.69 1.05 0.9 0.9 1.1 1.5 1.5 1.0 2.9

56 63 71 80 90 100 112 132 160 180 200 225 250 280 315

Values for 50 Hz. For service on 60 Hz, reduce values by 10% * Consult according to direction of force

AEG Electric Motors - 2.1 e/2005 - page 16

Permissible radial forces

without additional axial force (Ball bearings)

Nominal life = 20.000 h (Lh10)

FR = permissible radial force in kN X = Distance between point of application of force and shaft shoulder (e.g. half pulley width)

Size 56 63 71 80 90SL 100L 112M FR in N when 2p= 2 340 385 463 590 675 925 930

4 428 485 583 830 940 1295 1300

6 668 860 975 1335 1340

8 735 945 1070 1470 1476

3.0 kN 2.6

AM 132

3.0 kN

AM 160

3.0 kN 2.6

AM 180

6 kN

75 01 /m in 100 0

AM 200

75 01 /m in

10 00 15 00

2.6

5

75

01 /m 1 0 in 00

2.2

2.2

2.2

4

150

1.8 FR

150

0

1.8

0

3

750 1 /min 1000

1500 3000

1.8 FR

300 0

1.4

FR

3000

1.4

FR

1.4

300

0

2

1.0 0 40 x 80 mm 120

1.0 0 40 x 80 mm 120

1.0 0 40 x 80 mm 120

1 0 40 x 80 mm 120

6 kN 5

AM 225

6 kN 5

AM 250

6 kN 5

AM 280

12 kN

AM 315

750 1/m in 100 0

750 1/m in 100 0

10

75 0

1/mi n

150 0

8

4

750 1/m in 100 0

1500

3000

4

1000

1500

4

1500

3 FR

3000

3 FR

3 FR

3000

FR

6

3000

2

2

2

4

1 0 60 x 120 mm 180

1 0 60 x 120 mm 180

1 0 60 x 120 mm 180

2 0 60 x 120 mm 180

AEG Electric Motors - 2.1 e/2005 - page 17

Reinforced bearings (special design)

Roller bearings to DIN 5412 Frame size No. of poles 160 2-8 180 2-8 200 2-8 225 2-8 Drive end NU NU NU NU 209 210 212 213 E E E E Non-drive end 6209-2Z C3 6210-2Z C3 6212-2Z C3 6213-Z C3 Frame size No. of poles 250 2-8 280 2-8 315 2 4-8 315SY 4-8 Drive end NU NU NU NU NU 214 216 316 319 319 E E E E E Non-drive end 6214 6216 6316 6319 6316 C3 C3 C3 C3 C3

The modification from standard design to roller bearings is not possible, except for frame size 315.

Permissible radial forces

without additional axial forces (Roller bearings)

AM 160 AM 180

FR = permissible radial force in kN X = Distance between point of application of force and shaft shoulder (e.g. half pulley width)

6 kN 5 10 kN 8

3.6 kN 3.2

AM 200

10 kN

AM 225

0 0,1 150

8

0 75

2.8

4

6

15 00

in m 1/

6

01 ,7 5 00

, 00 10

00 15

/m

0 150

00, ,10

in

,10

, 00

2.4 FR

3 FR

in

50

7

1/ m

in

4 FR FR

4

750

1/m

2.0

2

2

2

1.6 0 40 x 80 mm 120

1 0 40 x 80 mm 120

0 0 40 x 80 mm 120

0 0 60 x 120 mm 180

10 kN 9

AM 250

14 kN 12

00 ,10 750

AM 280

10 00 1/ 7 5 m in 0

22 kN 18

AM 315

750 1/m in

100 0 150 0

8

10

15 00

14

in 1/m 0 150

7 FR FR

8 FR

10

6

6

6

5 0 60 x 120 mm 180

4 0 60 x 120 mm 180

2 0 60 x 120 mm 180

AEG Electric Motors - 2.1 e/2005 - page 18

Special bearings and flanges

Frame size IM B3 / IM B5 Oversized bearing 6308 6309 6310 6312 6313 6314 6316 IM B14 Oversized bearing C250-6309 IM B5 Reduced flange A250* A300 A300 A350* A400 A450 A450* -

132 160 180 200 225 250 280 315

*not interchangeable with standard motors

Belt drive

The data apply only to the normal drive end shaft extension of IM B3 motors with one speed. Calculation of belt drive: FR = 19120 · P ·k D1 · n FR P n D1 k = = = = = Radial shaft load in N Output in kW Speed in min-1 Pulley diameter in m Belt tension factor, varying with the type of belt, assumed to be approximately: 3-4 for normal flat belt without idler pulley 2-2.5 for normal flat belt with idler pulley 2.2-2.5 for V-belt For exact data apply to the belt manufacturer.

AEG Electric Motors - 2.1 e/2005 - page 19

Lubrication and maintenance of bearings

Bearings of standard motors up to frame size 250 have permanent lubrication. Bearing grease K3N to DIN 51 825 (e.g. KLÜBER ASONIC GHY72, ESSO UNIREX N3 or similar) is used. Maintenance-free life for motors with permanent lubrication at ambient temperature of 40° C and service at 50 Hz: 2 and 4/2 pole motors 10,000 h 4 and more pole motors 20,000 h, but not more than 4 years. From frame size 280 upwards the motors are equipped with regreasing device and grease slinger (possible from frame size 160 at extra cost). First lubrication is made with grease K3N to DIN 51 825 (lithium-based, water resistant to DIN 51 807 part 1: grade 0 or 1). For motors with regreasing device, regreasing interval and required quantity of grease is indicated on the nameplate. For regreasing please observe the Operating Instructions. Where unfavourable conditions prevail (e.g. high ambient temperature, dusty conditions, corrosive atmosphere, operation by frequency converter), relubrication should be carried out more frequently.

Lubricating nipples

Flat lubricating nipples M 10x1 to DIN 3404.

Cooling

Surface cooling, independent of the direction of rotation. Motors type AM available without internal fan as type AG, e.g. for installation in a directed air stream (outputs on request).

Vibration

The amplitude of vibration in electric motors is governed by EN 60034-14 Mechanical vibration of rotating electrical machines with shaft heights 56 and larger - methods of measurement and limits. Standard motors are designed to vibration grade A (normal). Vibration grade B are available at extra cost. Pole-changing motors in Dahlander connection can only be supplied in vibration grade A. Rotors are at present dynamically balanced with half key fitted as per DIN ISO 8821. Other balancing only on request. The motors are identified as follows: "H" or "blank" means balanced with half key "F" means balanced with full key "N" means no key

AEG Electric Motors - 2.1 e/2005 - page 20

Position and dimensions of key

Frame size 56 63 71 80 90 100 112 132 160 180 200 225 2 poles 225 4 poles 250 2 poles 250 4 poles 280 2 poles 280 4 poles 315 2 poles 315 4 poles d x l1 9 x 20 11 x 23 14 x 30 19 x 40 24 x 50 28 x 60 28 x 60 38 x 80 42 x 110 48 x 110 55 x 110 55 x 110 60 x 140 60 x 140 65 x 140 65 x 140 75 x 140 65 x 140 80 x 170 bxh 3x3 4x4 5x5 6x6 8x7 8x7 8x7 10 x 8 12 x 8 14 x 9 16 x 10 16 x 10 18 x 11 18 x 11 18 x 11 18 x 11 20 x 12 18 x 11 22 x 14 l2 15 15 20 30 40 50 50 70 100 100 100 100 110 110 110 100 100 125 140 l3 2.5 4 5 6 6 6 6 5 5 5 5 5 10 10 10 10 10 7.5 10 t 10.2 12.5 16 21.5 27 31 31 41 45 51.5 59 59 64 64 69 69 79.5 69 85

l2

l3

d

l1

b

t

h

Dimensions in mm For larger shafts in special design the dimensions l2 and l3 are maintained.

Anti-condensation heater

On request, motors which due to strong temperature fluctuations are exposed to condensation during standstill, can be fitted against surcharge with an anticondensation heater (space heater). For supply voltage and heater rating please refer to the following table:

Frame size 112 - 160 180 - 225 250 - 280 315

Supply voltage (V) 110 or 230 " " "

Heater rating per motor (W) 40 50 65 99

During operation of the motor, the heating must be switched off.

AEG Electric Motors - 2.1 e/2005 - page 21

Noise

The noise level of an electrical machine is determined by measuring the sound pressure level in accordance with curve A of the sound level meter to EN 60651 and is indicated in dB (A). The permitted noise levels of electrical machines are fixed in EN 60034-9 (IEC 34-9). The noise level of our motors is well below these limit values. Air-borne sound measurements are carried out in an anechoic testing chamber to EN 21680-ISO 1680. Speed corresponding to a mains frequency of 50 Hz and the number of poles.

Measures for noise reduction

With special measures noise level can be reduced (special fan, noise reducing hood, etc.).

Noise levels

The noise values listed below refer to 50 Hz at rated voltage with a tolerance of up to + 3 dB(A). Values for pole-changing motors on request. For 60 Hz supply values are 3-5 dB(A) higher.

Sound pressure level LpA and sound power level LWA for three-phase single-speed motors with dimensions and output ratings to IEC 60072 Frame size 56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 2 pole LWA LpA 57 58 61 72 74 78 80 81 87 87 87 88 90 92 93 48 49 52 60 62 66 68 69 74 74 74 75 76 78 79 4 pole LWA LpA 47 47 51 60 61 62 65 71 75 77 78 79 81 83 85 38 38 42 48 49 50 53 59 62 64 65 66 67 69 71 6 pole LWA LpA 8 pole LWA LpA

49 52 58 62 65 69 71 72 73 75 77 80 82

40 40 46 51 53 57 58 59 60 62 63 66 68

47 54 58 58 64 69 71 72 73 74 75 79

35 42 46 46 52 56 58 59 60 60 61 65

AEG Electric Motors - 2.1 e/2005 - page 22

S.p.a . .e . p a.r.t s. .f.o.r. .t h r e.e.-.p . . a.s e. .m . . t . . r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .r . ... .. . ..... . .h . .. .. o . o. s

Part description

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Shaft protection Dust seal drive end Endshield drive end Bearing drive end Stator frame Terminal board Fixing screw terminal board Gasket terminal box Terminal box Fixing screw terminal box Terminal box lid Fixing screw terminal box lid Gasket terminal box lid Blank gland plug Blank gland plug 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Key Rotor complete Bearing non-drive end Pre-load washer Endshield non-drive end Fan cover Fixing screw fan cover Fan Fixing bolt endshield non-drive end Fixing bolt endshield drive end Fixing bolt motor feet Motor feet Fixing washer motor feet Fixing nut motor feet

In enquires and orders for spare parts please state always: Designation of spare part, motor type, mounting arrangement, motor serial number (Product No. when available) Enquires and orders cannot be handled without these data.

AEG Electric Motors - 2.1 e/2005 - page 23

E . .r . . e . i .n . .l.e.c.t . .i.c.a.l. .d . . s. .g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rated voltage

For the rated voltage of the motors, EN 60 034-1 allows a tolerance of ± 5 %. According to IEC 60038, the mains voltages may have a tolerance of ± 10 %. Therefore the motors are designed for the following rated voltage ranges (exceptions are shown in the data tables):

Mains voltage to DIN IEC 38 230 V ± 10% 400 V ± 10% 690 V ± 10%

Rated voltage range of motor 218-242 V ± 5% 380-420 V ± 5% 655-725 V ± 5%

Within the rated motor voltage range, the permissible maximum temperature is not exceeded. When the motors are operated at the limits of the voltage tolerance, the permissible overtemperature of the stator winding may be exceeded by 10 K. For frame sizes 56 to 132 nameplates are marked with the maximum rated currents within the stated voltage ranges. For motors in 500 V, 50 Hz design, as well as all abnormal voltages, no voltage range is marked. The voltage tolerances to EN 60034-1 apply.

Rated frequency

50 Hz motors can also be operated on 60 Hz mains, provided the mains voltage increases proportionally to the frequency. The relative values for starting and breakaway torque remain nearly unchanged and slightly increase for the starting current. The rated speed increases by the factor 1.2 and output by factor 1.15. Should a motor designed for 50 Hz be operated at 60 Hz without the voltage being increased, the rated output of the motor cannot be increased. Under these operating conditions, rated speed increases by factor 1.2. The relative values for starting and breakaway torque are reduced by factor 0.82 and for starting current by factor 0.9.

Additionally to the voltage range for 50 Hz operation, single-speed motors in frame sizes 56 to 315 are also marked with the voltage range for 60 Hz operation. Example:

Frame sizes 56-132

Type AM90SAA4 IEC 600343-Mot No 16021169 H Th.Cl. F(B) IP55 50Hz:/Y230/400 1,1kW 218-242/380-420V 5,4/3,1A 60Hz:/Y265/460 1,25kW 250-277/440-480V 5,4/3,1A 1400/1680 min-1 cos 0,74/0,74

Frame sizes 160-315

Type AM280MT4Q4 IEC 60034 3-Mot No 13021646 H Th.Cl. F(B) IP55 50Hz:/Y400/690V 90kW 380-420/655-725V 168/97A 60Hz: 460V 103kW 440-480V 160A cos 0,85/0,86 1480/1780 min-1 Anticondensation Heater 230V 65W. Bearing LA/LO:6216C3.Grease: UNIREX N3 ESSO Protector type PTC 160°.Release temperatire 155°.Ready temperature 145°C After 5500h/18 ccm grease

AEG Electric Motors - 2.1 e/2005 - page 24

Rated current

The rated currents listed in the data tables apply to an operating voltage of 400 V. The conversion to other operating voltages, with output and frequency remaining unchanged, is to be made as follows: Nominal voltage (V) Conversion factor x lN 230 1.74 380 1.05 400 1.0 440 0.91 500 0.80 660 0.61 690 0.58

Rated torque

Rated torque in Nm = 9550 x Rated voltage in kW Rated speed in min-1

Output

The outputs stated in this catalogue are for constant load in continuous running duty S1 according to EN 60034-1, based on an ambient temperature of 40° C and installation at altitudes up to 1000 m above sea level. For severe operating conditions, e.g. high switching rate, long run-up time or electric braking, a thermal reserve is necessary, which could call for higher thermal class or the use of a motor with a higher rating. In these cases we recommend to enquire with detailed information on the operating conditions.

Overload

At operating temperature three-phase motors are capable of withstanding an overload for 15 seconds at 1.5 times the rated torque at rated voltage. This overload is according to EN 60034-1 and will not result in excessive heating. Utilizing thermal class F, motors can be operated continuously with an overload of 12 %. Nevertheless this is not valid for motors which to catalogue are utilized to thermal class F.

Connection

Motor output at 50 Hz under 1.5 kW 1.5 to 4 kW 5.5 to 90 kW 110 kW

1)

230 V 400 V Y standard standard standard on request

400 V 690 V Y standard standard standard

500 V Y

500 V

690 V standard standard

on request on request on request 1) on request on request on request on request standard standard

Available from 0.25 kW

AEG Electric Motors - 2.1 e/2005 - page 25

Connection diagrams

Windings of standard three-phase motors can be connected either in star or delta connection.

U1 W2 U2 V2

Star connection A star connection is obtained by connecting W2, U2, V2 terminals to eachother and the U1, V1, W1 terminals to the mains. The phase current and voltage are: Iph = In ; Uph = Un /

3

U1 W1 V1

V1

W1

L1

L2

L3

where In is the line current and Vn the line voltage referred to the star connection.

V2

U1 W2 U2

Delta connection A delta connection is obtained by connecting the end of a phase to the beginning of the next phase. The phase current Iph and the phase voltage Uph are:

U1

V1

W1

W1

V1

L1

L2

L3

Iph = In /

3;

Uph = Un

where In and Un are referred to the delta connection. Star-delta starting Star-delta starting allows a peak current reduction, ensuring however that the peak torque obtained is bigger than the resistant torque. Actually, it should be noted that the torque of an induction squirrel-cage motor is directly proportional to the square of the voltage. Motors whose rated voltage with delta connection corresponds to the mains voltage, can be started with the star-delta method. All motors can be supplied with windings designed for star-delta starting (for example: 400 V / 690 V Y). Pole-changing motors Standard pole-changing motors are designed for single voltage and direct-on-line starting (special design for Y--connection on request). When the ratio between the two speeds is from 1 to 2, the standard motors have one single winding (Dahlander connection). For the other speeds, the motors have two separate windings.

AM/AMV - two separate windings

/

L1 L2 L3

AM/AMV - two separate windings Y/Y

L1 L2 L3

1U 2U 2V 2W

2U 2U 2V 2W

1U 2U 2V 2W

2U 2U 2V 2W

1U 1W 1V

1V

1W

1U

1V

1W 1W 1V

1U

1V

1W

1U

1V

1W

2W

2V

2W

2V

Low speed

L1 L2 L3

High speed

Low speed

L1 L2 L3

High speed

AM - Dahlander connection

/YY

L1 L2 L3

AMV - Dahlander connection Y/YY

L1 L2 L3

1U 2U 2U 2V 2W 1W 1U 1W 2U 1V 2W 2V 1V 1W 1U 1V 1U 1V 1W 1W 2V 2W 2U 2V 2W

1U 2U 2W 2V 2W

2U 2U 2V 2W

1V 1U 2V 2U 1U 1V 1W 2W 1W 1U 2V 1V 1W

1V

Low speed

L1

L2

L3

High speed

Low speed

L1

L2

L3

High speed

AEG Electric Motors - 2.1 e/2005 - page 26

Insulation and temperature rise

Class F insulation to EN 60034-1 is used throughout. In standard design motors are intended for operation at 40° C ambient temperature with class B temperature rise only, with an overtemperature limit of 80 K. This also applies for the rated voltage range to IEC 60038. Exceptions are shown on the data tables.

Temperature rise (T*) and maximum temperatures at the hottest points of the winding (Tmax) according to the temperature classes of EN 60034-1.

T* Class B Class F Class H

*Measurement by resistance method

Tmax 125° C 155° C 180° C

80 K 105 K 125 K

Output reduction at ambient temperatures over 40° C

45° C Ambient temperature Reduction of nominal output to approx. 95 % 50° C 90 % 55° C 85 % 60° C 80 %

When a winding is utilized to temperature class F (105K), no output reduction is required up to an ambient temperature of 60° C. This does not apply to motors which in their standard design are already utilized to thermal class F.

AEG Electric Motors - 2.1 e/2005 - page 27

Installation at altitudes of more than 1000 m above sea level (see also EN 60034-1)

Altitude of installation At 40°C ambient temperature and thermal class B Rated output reduced to approx. At 40°C ambient temperature and thermal class F Rated output reduced to approx. Full nominal output to data tables with thermal class B and ambient temperature of Full nominal output to data tables with thermal class F and ambient temperature of 2000 m 92 % 89 % 32° C 30° C 3000 m 84 % 79 % 24° C 19° C 4000 m 76 % 68 % 16° C 9° C

Starting rate

The permissible number of starts per hour can be taken as given in the table below, provided the following conditions are met: Additional moment of inertia moment of inertia of the rotor: load torque rising with the square of the speed up to nominal torque; starts at even intervals.

Shaft height

Permissible No. of starts per hour for 2p =2 =4 250 140 60 30 15 8 6 350 160 80 50 30 12

56 - 71 80 - 100 112 - 132 160 - 180 200 - 225 250 - 315

100 60 30 15 8 4

For permissible number of starts for larger and pole-changing motors please consult us, indicating the complete operating conditions.

AEG Electric Motors - 2.1 e/2005 - page 28

Thermal protection

The decision on a particular type of thermal protection should be taken according to the actual operating conditions. Motors may be protected by means of current-dependent thermal protection switches, overcurrent relays and temperature detectors.

Thermal protection is possible as follows: · Thermal protection switch with bimetal release · Thermistor protection with semiconductor temperature detectors (PTC) in the stator winding in connection with release (if required, with additional motor protection switch). · Bimetal temperature detector as N/C or N/O in the stator winding (if required, with additional motor protection switch). · Resistance thermometer for monitoring winding and bearing temperature.

Should protection of the motor be required, we install protection switch with bimetal release up to frame size 112 and semiconductor temperature detectors in motors 132.

Although there are motors available from stock with built-in semiconductor temperature detector, a special remark has to be made in the enquiry or order when motor protection is required.

Operating specifications Thermal cut-out

NORMALLY OPEN

N/O TYPE Ti = Activation temperature Tr = Reset temperature

1

0

Tr

Ti

K

Operating specifications of the thermistors

NORMALLY CLOSED

N/C TYPE Ti = Activation temperature Tr = Reset temperature

PTC TYPE Ti = Activation temperature

OHM

1

Resistance

0

0

Tr

Ti

K

Ti

K

AEG Electric Motors - 2.1 e/2005 - page 29

Examples of connection

Protection method

Protection

Motor protection switch with thermal and electromagnetic overcurrent release

against: · Overload in continuous service · Locked rotor

Contactor with overcurrent relay Thermistor protection and fuse

in service against: · Overload in continous service · Long starting and braking periods · High switching rate in case of fault against: · Obstruction of cooling · Increased ambient temperature · Single-phase operation · Frequency fluctuations · Switching against locked rotor

Semiconductor temperature detector with release

in service against: · Overload in continous service · Long starting and braking periods · High switching rate in case of fault against: · Obstruction of cooling · Increased ambient temperature · Single-phase operation · Frequency fluctuations · Switching against locked rotor

AEG Electric Motors - 2.1 e/2005 - page 30

Three-phase cage motors driven by frequency converters ...............................................................................

The motors frame sizes 90 upwards in standard design are suitable for operation on static frequency converters, taking into account the following remarks: · Maximum converter output voltage 500V at peak voltages Û 1460V and du/dt 13 kV/us. For higher converter output voltages or stresses, a special insulation is required. · With square characteristic of the load torque, motors can be driven with their rated torque. · For constant torque, the rated torque of motors with internal cooling must be reduced due to reduced cooling air inlet. Depending on the control range, the use of an external fan would be advisable. · The motors frame sizes 90 ­ 112 are suitable for a maximum output frequency of the converter of 60 Hz (e.g. applications with square torque, control range 1 : 10, such as pumps and fans). For higher frequencies, a special range with type designation AMI is available on request. From frame size 132 upwards, motors designed /Y 230/400 V, 50 Hz can be operated in delta with a maximum frequency of 87 Hz (observe mechanical limit speed). · Insulated or hybride bearings may be necessary on critical applications. We generally recommend the use of insulated bearings for motors frame size 225 upwards. The motors frame size 56 ­ 80 can be operated on single-phase converters up to maximum 60 Hz. (Special range with type designation AMI for operation on threephase converters with output voltage 400 V and output frequency > 60 Hz). The electrical values and dimensions of the range AMI in frame size 56 to 112 are identical to AM motors (see data tables pages 36-41).

1

no field weakening

Thermal maximum-torque curve for approximate determination of the required torque reduction with constant load torque curve

with field weakening

MU/MN

2 3

1 2 3

External cooling Internal cooling motors 2p = 2 Internal cooling motors 2p = 4-8

f [Hz]

Noise

Depending on the operating point and converter type, converter-fed motors produce between approx. 4 - 10 dB(A) higher noise values than when supplied from the mains. For motors driven with a frequency over 50 Hz, more fan noise is produced. We recommend the use of an external fan.

AEG Electric Motors - 2.1 e/2005 - page 31

Degree of protection

Depending on the accessories used.

Mechanical limit speeds

For motors of standard design, the following maximum operating speeds are permitted: Frame size

1)

2p = 2 min

-1

2p=4-8 min

-1

56-112 132-180 200 225 250 280, 315S YE 315S / M ZE 315 L

1)

3600 6000 5000 4500 4300 4300 3600 3600

1800 6000 5000 4500 4300 3800 3600 3000

Higher speeds with special range AMI

Vibration amplitude

When operating at high speeds (according to frequency > 60 Hz) a reduced vibration amplitude "R" to DIN ISO 2373/DIN VDE 0530, part 14 may be required, measured at a mains frequency of 50 Hz or 60 Hz and sinusoidal mains voltage.

Accessories

Motors are available with the following accessory: · Encoder with internal or external cooling

Encoder (standard design)

Supply voltage UB Pulses per revolution Outputs 5V 500-2048 2 signals with rectangular pulses A, B 2 signals with inverted rectangular pulses A, B zero pulse and inverted zero pulse 90º 2.5 V 0.5 V

Pulse displacement between outputs Output amplitude UHigh ULow Maximum frequency Maximum speed Temperature range Degree of protection 100 kHz

3,000 (6,000) min -20ºC to + 85ºC IP 54

-1

AEG Electric Motors - 2.1 e/2005 - page 32

Or . e . d . . . . . .d . .r . . . a.t.a. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Motors for normal continuous duty (S1) and normal operating conditions

Quotation (if submitted) Quantity Designation Output (for pole-changing motors, outputs referred to speeds) Speed (for pole-changing motors, outputs referred to outputs) Direction of rotation (viewed on shaft extension) Mounting arrangement (to IEC 60034-7) Degree of protection, motor/terminal box (to IEC 60034-5) Mains voltage Mains frequency Method of starting (direct-on-line or Y-) Location of terminal box Machine to be driven V Hz No./Date Units Type

kW

min-1

Dimensions of cables, if these differ from those allocated by VDE 0100, referred to an ambient temperature of 40° C, or when aluminium conductors are used. It should be stated when parallel connected conductors are used.

Additional information for special designs

Second or non-standard shaft extension Radial sealing ring Paint coating Corrosive protection Vibration level Anti-condensation heating Temperature detectors Noise requirements Mechanical or electrical brake Special stipulations

AEG Electric Motors - 2.1 e/2005 - page 33

Additional information for special duties and difficult operating conditions

S 2: ... min (short-time duty) S 3: ... % - ... min (intermittent duty) S 4: ... % - JM ... kgm2 - Jext ... kgm2 (intermittent duty with starting) S 5: ... % - JM ... kgm2 - Jext ... kgm2 (intermittent duty with electric braking) S 6: ... % - min (continuous-operation periodic duty with intermittent load) S 7: .JM ... kgm2 - Jext ... kgm2 (continuous-operation periodic duty with electric braking) S 8: .JM ... kgm2 - Jext ... kgm2 (continuous-operation periodic duty with speed changes) S 9: ... kW equ (continuous duty with non-periodic load and speed variations). For this duty type suitable full load values should be taken as the overload concept. S10: p/t .... r .... TL (Duty with discrete constant loads). Starting conditions (no-load or loaded starting) Shock loads Load torque curve during run-up (characteristic) Moment of inertia (Jext) referred to the motor shaft Description of the type of drive (direct coupling, flat or V-belt, straight or helical gears, sprocket, crank, eccentric cam, etc.) Radial force (or diameter of drive element) N kgm2

Direction of force and point of application (distance from shaft shoulder or width of drive element) mm Axial force and direction of application (pull/thrust) N

Ambient conditions (e.g. increased humidity, dust accumulation, corrosive gases or vapours, increased or extremely low ambient temperature, outdoor installation, installation at altitudes over 1000 m above sea level, extraneous vibration, etc.)

AEG Electric Motors - 2.1 e/2005 - page 34

Ty p . . . . . n . . . . . . . . . . e. .d.e s.i.g . . a.t i o.n. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Apart from other information, it is necessary to specify the exact type designation in all enquiries, when ordering spare parts or replacement motors or when asking for documentary information. The type designation of our motors comprises 9 points of reference, each of which may consist of several letters and/or numerals. The meaning of each symbol can be seen from the following table. For motors not included in our standard range, special symbols may be used which are not listed here.

Meaning of the symbols

Ref. point 1 2 Meaning Description of symbols used for our motors

Type of motor Cooling

A M G MFV blank V H HE I

Asynchronous motor Surface cooled with external fan, cooling fins Surface cooled without external fan, cooling fins Surface cooled with forced ventilation, cooling fins Three-phase motor Three-phase pole-changing motor for driving fans Three-phase motor, efficiency to EPACT regulations Three-phase motor, efficiency eff 1 to CEMEP Voluntary Agreement Special design for three-phase motor driven with frequency converter

3

Type of motor

4 5

Shaft centre height Frame length

56, 63, 71, 80, 90, 100, 112, 132,160, 180, 200, 225, 250, 280, 315 Z S M L A B C D A G E 2 4 6 8 R3 4/2 8/4 4/6 6/8 High resistance rotor Frame size 56-112 Mechanical dimension (short) Mechanical dimension (medium) Mechanical dimension (long) Stage of development X,P,J Y,R,L Z,V,T Frame size 132-315

6

Mechanical design and output value Frame material and/or stage of development Number of poles

7

Aluminium frame Cast iron frame Stage of development

8

9

Special features

Examples

AEG Electric Motors - 2.1 e/2005 - page 35

Three-phase squirrel cage motors designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at 400V IN 380-420V Direct-on-line starting Starting Breakaway Pull-up current torque torque ratio ratio ratio IA/IN MA/MN MS/MN Pull-out torque ratio MK/MN Moment of inertia Weight

kW

HP

min-1

50%

75%

cos

100%

10-3 kgm2

kg

3000 min-1 (2 poles)

AM 56Z AA AM 56Z BA AM 63Z AA AM 63Z BA AM 63Z CA AM 71Z AA AM 71Z BA AM 71Z CA AM 80Z AA AM 80Z BA AM 80Z CA AM AM AM AM 90S AA 90S BA 90L CA 90L DA 2 2 2 2 2* 2 2 2* 2 2 2* 2 2* 2 2* 0.09 0.12 0.18 0.25 0.37 0.37 0.55 0.75 0.12 0.16 0.25 0.33 0.50 2810 2800 2790 2790 2800 2820 2830 2800 2840 2810 2825 2830 2805 2860 2860 2860 2835 2865 2900 2930 2885 2890 2870 2900 2890 2925 2920 2925 2920 2925 2925 49 51 54 56.4 54 54 57 58 67.7 74.3 76.5 75.4 75.18 78.6 78.8 81.7 82.4 83.5 80.9 81.0 84.7 86.5 84.5 88.2 88.0 86.6 88.0 88.8 89.0 89.1 89.3 53 56 58 61.2 58 60.5 64 64.3 73.0 77.3 79.4 78.4 78.3 81.4 81.9 82.2 83.8 85.3 84.2 84.7 86.2 87.6 86.6 89.2 89.0 88.5 89.6 90.3 90.8 90.7 91.4 58.3 61.6 63 65.3 63 65.3 70.8 71 74.5 77.6 79.1 78.6 78.5 81.8 82.3 82.6 83.0 85.0 85.0 86.2 85.7 87.0 86.7 88.7 88.5 88.7 89.7 90.4 90.8 90.8 91.5 0.62 0.70 0.77 0.77 0.75 0.70 0.70 0.75 0.78 0.82 0.83 0.82 0.80 0.81 0.80 0.85 0.88 0.85 0.84 0.81 0.86 0.89 0.83 0.87 0.88 0.84 0.85 0.86 0.87 0.86 0.86 0.38 0.4 0.6 0.71 1.13 1.1 1.6 1.9 1.9 2.5 3.3 3.4 4.2 4.9 6.5 6.4 8.0 10.8 8.5 11.5 10.8 14.1 18.7 20.6 28.0 21.5 28.5 34.5 41 41 56 0.4 0.42 0.66 0.75 1.25 1.2 1.7 2.0 2.0 2.6 3.4 3.5 4.3 4.9 6.8 6.7 8.1 11.0 8.7 12.3 11.0 14.5 19.8 21 28.5 22 29.5 35 42 42 57.5 3.9 3.9 4.2 4.5 4.6 4.7 4.8 5.2 5.0 4.6 5.0 5.0 4.5 7.1 7.2 6.0 6.2 7.2 8.1 9.0 6.6 7.2 7.0 7.8 7.8 6.7 7.2 7.6 7.9 7.4 7.9 3.8 3.8 3 3.2 3.4 3.6 3.2 3.1 2.8 2.4 2.9 3.1 2.6 4.1 3.9 3.1 2.9 3.5 3.8 4.2 2.5 2.6 2.8 2.9 3.1 2.3 2.4 2.7 2.7 2.5 2.7 3.8 3.8 3.1 3.2 3.3 3.4 3.1 3.2 2.8 2.8 3.0 2.9 2.4 3.6 3.4 3.1 2.5 3.4 3.6 2.6 2.1 2.2 2.4 2.5 2.6 2.2 2.2 2.5 2.5 2.3 2.5

Aluminium frame

3.9 3.9 3.2 3.3 3.4 3.6 3.3 3.1 2.9 2.9 3.3 3.0 2.5 4.0 3.8 3.3 2.9 4.1 4.0 3.6 2.9 3.0 3.2 3.3 3.4 3.0 3.1 3.3 3.3 3.2 3.4 0.09 0.1 0.13 0.19 0.20 0.36 0.46 0.58 0.75 0.89 1.05 1.37 1.37 1.8 2.09 2.80 3.35 4.5 6.48 8.58 10.0 14.0 14.0 20.5 25.0 28 36 42 52 65 88 3.4 3.5 4.1 4.6 4.7 5.7 6.3 6.9 8.4 9.5 11.1 12.7 12.7 16.0 18.7 19.3 19.7 25.9 27.4 33.6 40 45 48 53 59 81 93 101 114 130 150

1)

1)

1)

0.50 0.75 1.0 1)

0.75 1.1 1.5 1) 1.5 1.8 2.2 3 1) 3 4 1) 5.5 1) 4 5.5

1.5 2.0 2.0 2.5 3.0 4.0 4.0 5.5 7.5 5.5 7.5 7.5 10.0 12.5 15.0 20.0 15 20 25 30 30 40

1)

1)

AM 100L AA 2 AM 100L BA 2* AM 100L CA 2* AM 112M AA 2 AM 112M BA 2* AM AM AM AM AM AM AM AM AM 132S YA 132S ZA 132M ZA 132M RA 132M TA 160M VA 160M XA 160L XA 160L RA 2 2 2* 2* 2* 2 2 2 2*

1) 1)

1)

1)

5.5 7.5 9.2 1) 11 15 1) 11 15 18.5 22 1) 22 30

1)

1)

1)

AM 180M XA 2 AM 180M RA 2*

1)

1)

1) Temperature rise to class F * Higher output (progressive motor)

AEG Electric Motors - 2.1 e/2005 - page 36

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at 400V IN 380-420V Direct-on-line starting Starting Breakaway Pull-up current torque torque ratio ratio ratio IA/IN MA/MN MS/MN Pull-out torque ratio MK/MN Moment of inertia Weight

kW

HP

min-1

50%

75%

cos

100%

10-3 kgm2

kg

3000 min-1 (2 poles)

AM AM AM AM AM AM AM AM AM 132S YG 132S ZG 132M ZG 132M RG 132M TG 160M VG 160M XG 160L XG 160L RG 2 2 2* 2* 2* 2 2 2 2* 5.5 7.5 9.2 1) 11 15 1) 11 15 18.5 22 1) 22 30 30 37 45 55 75 90 110 132 160 200 7.5 10.0 12.5 15.0 20.0 15 20 25 30 30 40 40 50 60 75 100 125 150 180 220 270 2885 2890 2870 2900 2890 2925 2920 2925 2920 2925 2925 2945 2950 2945 2950 2975 2975 2975 2980 2980 2980 84.7 86.5 84.5 88.2 88.0 86.6 88.0 88.8 89.0 89.1 89.3 89.2 90.0 90.9 90.9 90.9 93.6 92.8 94.1 94.7 95.2 86.2 87.6 86.6 89.2 89.0 88.5 89.6 90.3 90.8 90.7 91.4 91.1 91.8 92.4 92.7 92.9 94.8 94.4 95.2 95.7 96.1 85.7 87.0 86.7 88.7 88.5 88.7 89.7 90.4 90.8 90.8 91.5 91.6 92.2 92.6 93.1 93.7 94.1 95.0 95.5 95.9 96.3 0.86 0.89 0.83 0.87 0.88 0.84 0.85 0.86 0.87 0.86 0.86 0.85 0.86 0.89 0.89 0.87 0.89 0.87 0.88 0.90 0.91 10.8 14.1 18.7 20.6 28.0 21.5 28.5 34.5 41 41 56 56 67.5 80 96 134 156 193 227 267 329 11.0 14.5 19.8 21 28.5 22 29.5 35 42 42 57.5 57 69 83 101 136 161 198 235 280 347 6.6 7.2 7.0 7.8 7.8 6.7 7.2 7.6 7.9 7.4 7.9 7.8 7.7 7.8 7.5 7.2 7.3 7.8 6.8 7.2 7.8 2.5 2.6 2.8 2.9 3.1 2.3 2.4 2.7 2.7 2.5 2.7 2.2 2.2 2.4 2.3 1.9 1.9 1.9 2.4 2.5 2.7 2.1 2.2 2.4 2.5 2.6 2.2 2.2 2.5 2.5 2.3 2.5 2.0 2.0 1.9 1.8 1.5 1.5 1.5 1.3 1.3 1.3

Cast iron frame

2.9 3.0 3.2 3.3 3.4 3.0 3.1 3.3 3.3 3.2 3.4 3.0 3.0 2.8 3.0 3.2 3.2 3.2 2.6 2.6 2.7 10.0 14.0 14.0 20.5 25.0 28 36 42 52 65 88 120 145 270 424 770 957 1000 1200 1400 1600 55 60 63 68 74 101 113 121 134 155 175 212 230 310 410 540 615 650 810 900 1000

1)

1)

1)

AM 180M XG 2 AM 180M RG 2* AM 200L LG AM 200L NG AM 225M N AM 250M N AM 280S T AM 280M T AM AM AM AM 315S YE 315M ZE 315L YE 315L ZE 2 2 2 2 2 2 2 2 2 2

1)

1)

1)

1)

1) Temperature rise to class F * Higher output (progressive motor)

AEG Electric Motors - 2.1 e/2005 - page 37

Three-phase squirrel cage motors designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at 400V IN 380-420V Direct-on-line starting Starting Breakaway Pull-up current torque torque ratio ratio ratio IA/IN MA/MN MS/MN Pull-out torque ratio MK/MN Moment of inertia Weight

kW

HP

min-1

50%

75%

cos

100%

10-3 kgm2

kg

1500 min-1 (4 poles)

AM 56Z AA AM 56Z BA AM 63Z AA AM 63Z BA AM 63Z CA AM 71Z AA AM 71Z BA AM 71Z CA AM 80Z AA AM 80Z BA AM 80Z CA AM AM AM AM 90S AA 90L BA 90L CA 90L DA 4 4* 4 4 4* 4 4 4* 4 4 4* 4 4 4* 4* 0.06 0.09 0.12 0.18 0.25 0.25 0.37 0.55 0.08 0.12 0.16 0.25 0.33 0.33 0.50 0.75 1300 1330 1350 1330 1360 1340 1370 1380 1400 1410 1385 1400 1400 1380 1400 1435 1425 1400 1430 1430 1445 1445 1440 1430 1460 1460 1450 1455 1460 1460 1455 42 43 46 47 49 55 60 61 67.0 62.5 74.1 69.6 75.6 75.1 76.3 77.5 81.7 82.1 84.5 85.9 85.6 87.7 87.3 87.5 88.4 89.6 89.2 89.8 90.0 90.4 90.4 44 47 50 50 52.5 59 63 64 69.0 69.0 76.4 75.4 78.7 77.8 79.3 80.2 83.4 83.0 85.3 86.2 86.6 88.1 88.1 87.9 89.2 90.3 90.2 90.7 90.8 91.1 91.4 48 51 54 56 58 64 67 68 70.0 70.6 75.9 76.5 78.6 77.3 79.3 81.0 82.8 81.6 84.2 85.2 85.7 87.0 87.2 86.8 88.6 89.6 90.2 90.5 90.3 90.5 91.4 0.55 0.60 0.69 0.70 0.60 0.71 0.67 0.67 0.72 0.71 0.77 0.78 0.77 0.80 0.75 0.74 0.76 0.78 0.81 0.83 0.82 0.84 0.83 0.84 0.83 0.85 0.81 0.82 0.84 0.84 0.82 0.35 0.4 0.45 0.6 1.0 0.7 1.18 1.73 1.6 2.2 2.8 2.7 3.6 4.2 5.3 5.4 6.8 9.2 8.5 11.4 11.3 14.8 18.5 22 21.5 29 37 42 35.5 42 58 0.4 0.45 0.5 0.65 1.2 0.8 1.25 1.8 1.7 2.3 2.9 2.9 3.7 4.3 5.5 5.6 6.9 9.3 8.8 11.7 11.7 15.5 19.2 22.5 22.5 29.5 38 43 36.5 43.5 60 2.6 2.5 2.4 2.3 2.7 3.2 3.3 3.6 3.6 4.4 4.4 5.2 5.7 5.5 4.8 5.3 4.6 6.0 6.3 6.5 6.2 6.5 6.4 6.7 6.8 7.2 7.4 7.5 7.2 7.3 7.8 2.1 2.2 2.0 1.9 2.2 1.9 2.2 2.4 2.6 2.8 2.5 2.5 2.8 2.7 2.9 2.5 2.4 2.6 2.2 2.2 2.4 2.6 2.7 2.8 2.3 2.4 2.7 2.7 2.7 2.7 3.0 2.0 2.1 1.9 1.8 2.0 1.8 2.1 2.3 2.5 2.3 2.5 2.4 2.6 2.5 2.8 2.4 2.3 2.4 2.0 2.0 2.1 2.1 2.2 2.2 2.1 2.1 2.4 2.4 2.2 2.2 2.4

Aluminium frame

2.1 2.2 2.0 1.9 2.1 2.0 2.2 2.4 2.6 2.8 2.6 2.8 3.0 2.9 3.2 2.7 2.5 2.9 2.8 2.9 2.9 2.9 3.0 3.1 2.9 3.0 3.3 3.3 3.0 3.0 3.2 0.14 0.14 0.25 0.27 0.30 0.63 0.76 0.98 1.58 2.00 2.41 2.5 3.13 3.13 4.05 4.6 5.58 6.05 12.2 15.2 22 30 30 36 59 82 82 93 105 118 150 3.2 3.3 4.1 4.6 4.9 5.2 5.4 6.3 8.2 9.3 10.6 12.5 14.5 14.5 17 19.5 22.5 25 29.5 34 46 55 56 65 86 102 102 112 125 135 150

1)

1)

0.55 0.75 1.1 1) 1.1 1.5 1.8 2.2 2.2 3 4 1) 4 5.5

0.75 1.0 1.5 1) 1.5 2.0 2.5 3.0 3.0 4.0 5.5 5.5 7.5 7.5 10.0 12.5 15.0 15 20 25 30 25 30 40

1) 1)

1) 1)

AM 100L AA 4 AM 100L BA 4 AM 100L CA 4* AM 112M AA 4 AM 112M BA 4* AM AM AM AM AM AM AM AM 132S ZA 132M ZA 132M ZA 132M TA 160M XA 160L XA 160L ZA 160L RA 4 4 4* 4* 4 4 4* 4*

1)

1)

1)

5.5 7.5 9.2 1) 11 1) 11 15 18.5 1) 22 1) 18.5 22 30 1)

1) 1)

1) 1)

AM 180M XA 4 AM 180L XA 4 AM 180L RA 4*

1)

1) Temperature rise to class F * Higher output (progressive motor)

AEG Electric Motors - 2.1 e/2005 - page 38

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at 400V IN 380-420V Direct-on-line starting Starting Breakaway Pull-up current torque torque ratio ratio ratio IA/IN MA/MN MS/MN Pull-out torque ratio MK/MN Moment of inertia Weight

kW

HP

min-1

50%

75%

cos

100%

10-3 kgm2

kg

1500 min-1 (4 poles)

AM AM AM AM AM AM AM AM 132S ZG 132M ZG 132M ZG 132M TG 160M XG 160L XG 160L ZG 160L RG 4 5.5 4 7.5 4* 9.2 1) 4* 11 1) 4 4 4* 4* 11 15 18.5 1) 22 1) 7.5 10.0 12.5 15.0 15 20 25 30 25 30 40 40 50 50 60 75 100 100 125 150 180 220 270 1445 1445 1440 1430 1460 1460 1450 1455 1460 1460 1455 1465 1465 1475 1475 1475 1470 1480 1480 1480 1485 1485 1485 85.6 87.7 87.3 87.5 88.4 89.6 89.2 89.8 90.0 90.4 90.4 90.5 91.7 90.8 91.7 92.6 92.3 92.4 92.9 93.8 94.1 94.6 95.0 86.6 88.1 88.1 87.9 89.2 90.3 90.2 90.7 90.8 91.1 91.4 91.6 92.4 92.1 92.7 93.3 93.4 93.6 94.0 94.7 95.2 95.5 95.8 85.7 87.0 87.2 86.8 88.6 89.6 90.2 90.5 90.3 90.5 91.4 91.5 92.4 92.2 92.6 93.1 93.6 93.7 94.1 94.7 95.5 95.7 96.0 0.82 0.84 0.83 0.84 0.83 0.85 0.81 0.82 0.84 0.84 0.82 0.84 0.83 0.84 0.86 0.84 0.82 0.84 0.84 0.84 0.86 0.88 0.89 11.3 14.8 18.5 22 21.5 29 37 42 35.5 42 58 56.5 69.5 69.5 81.5 103 142 139 165 200 228 274 342 11.7 15.5 19.2 22.5 22.5 29.5 38 43 36.5 43.5 60 58.5 71.5 71.5 85 107 146 143 171 208 239 288 359 6.2 6.5 6.4 6.7 6.8 7.2 7.4 7.5 7.2 7.3 7.8 7.0 7.4 7.5 7.6 6.5 7.3 6.5 6.6 7.1 7.3 7.3 7.6 2.4 2.6 2.7 2.8 2.3 2.4 2.7 2.7 2.7 2.7 3.0 2.4 2.6 2.3 2.3 3.5 3.9 2.1 2.2 2.3 2.1 2.1 2.3 2.1 2.1 2.2 2.2 2.1 2.1 2.4 2.4 2.2 2.2 2.4 1.8 2.0 2.0 2.0 2.1 2.3 1.8 1.8 1.8 1.6 1.5 1.6

Cast iron frame

2.9 2.9 3.0 3.1 2.9 3.0 3.3 3.3 3.0 3.0 3.2 2.6 2.8 2.9 2.9 2.4 2.7 2.7 2.7 2.8 2.8 2.8 2.8 22 30 30 36 59 82 82 93 105 118 150 195 248 356 461 640 812 990 1260 1400 2200 2500 3100 61 70 71 80 106 122 122 132 150 160 175 225 255 290 330 385 440 510 565 620 860 940 1120

1) 1)

1) 1)

AM 180M XG AM 180L XG AM 180L RG AM 200L NG AM 200L FG AM 225S N AM 225M N AM 250M N AM 250M K AM 280S T AM 280M T AM AM AM AM 315S YE 315M YE 315M ZE 315L ZE

4 18.5 4 22 4* 30 1) 4 30 4* 37 4 4 37 45

1)

1)

1)

4 55 4* 75 4 4 4 4 4 4 75 90 110 132 160 200

1)

1)

1) Temperature rise to class F * Higher output (progressive motor)

AEG Electric Motors - 2.1 e/2005 - page 39

Three-phase squirrel cage motors designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at 400V IN 380-420V Direct-on-line starting Starting Breakaway Pull-up current torque torque ratio ratio ratio IA/IN MA/MN MS/MN Pull-out torque ratio MK/MN Moment of inertia Weight

kW

HP

min-1

50%

75%

cos

100%

10-3 kgm2

kg

1000 min-1 (6 poles)

AM 71Z AA AM 71Z BA AM 80Z AA AM 80Z BA AM 90S AA AM 90L BA AM 100L AA AM 100L BA AM 112M AA AM 112M BA AM 112M CA AM AM AM AM 132S ZA 132M YA 132M ZA 132M TA 6 6 6 6 6 6 6 6* 6 6* 6* 6 6 6 6* 6 6 6 0.18 0.25 0.37 0.55 0.75 1.1 1.5 1.8 2.2 2.6 3 3 4 5.5 7.5 7.5 11 15

1)

Aluminium frame

0.25 0.33 0.5 0.75 1 1.5 2 2.5 3 3.5 4 4 5.5 7.5 10 1) 10 15 20

1)

850 870 910 910 910 908 930 940 940 930 940 955 955 955 950 965 965 970

44.0 46.0 47.0 60.0 71.0 71.0 70.0 71.0 81.0 82.2 83.0 81.6 83.2 83.8 85.0 86.8 88.6 90.5

47.0 50.0 58.0 64.0 73.0 73.0 75.0 75.0 83.0 83.7 84.0 83.7 84.9 85.2 85.7 87.7 89.0 90.8

51.0 54.0 60.0 68.0 72.0 72.0 72.0 76.0 82.0 82.4 84.0 83.4 84.5 84.6 85.0 87.0 88.1 90.0

0.73 0.68 0.72 0.67 0.63 0.63 0.71 0.67 0.72 0.73 0.75 0.75 0.76 0.77 0.77 0.82 0.82 0.83

0.7 1.0 1.2 1.8 2.4 3.5 4.2 5.1 5.3 6.3 7.0 7.0 9.1 12.3 16.5 15.2 22 29

0.75 1.1 1.25 1.8 2.5 3.6 4.4 5.3 5.4 6.5 7.2 7.1 9.2 12.5 16.9 15.9 22.5 30

2.2 2.5 2.7 2.9 2.9 3.0 3.7 4.2 4.4 4.9 5.3 5.8 6.2 6.2 6.3 5.9 6.1 6.7

1.6 1.7 1.6 2.2 1.7 1.7 1.8 2.4 2.4 3.0 2.9 2.1 2.3 2.3 2.3 1.9 2.0 2.2

1.5 1.6 1.6 2.1 1.5 1.5 1.8 2.4 2.4 2.9 2.9 1.8 1.9 1.9 1.9 1.7 1.8 1.8

1.6 1.7 2.1 2.1 1.7 1.7 2.3 2.8 2.6 3.1 2.9 2.7 2.8 2.8 2.8 2.5 2.6 2.8

0.6 0.9 1.97 2.47 3.18 4.78 6.73 9.43 14.18 16.73 18.7 27 34 40 46 78 102 169

5.7 6.3 8 9.4 11.6 15 17.5 22 26 29.7 39 43 49 54 62 83 100 130

1)

AM 160M ZA AM 160L ZA AM 180L ZA

1000 min-1 (6 poles)

AM AM AM AM 132S ZG 132M YG 132M ZG 132M TG 6 6 6 6* 6 6 6 6 6 6 6 6 6 3 4 5.5 7.5 7.5 11 15 18.5 22 30 37 45 55 4 5.5 7.5 10 1) 10 15 20 25 30 40 50 60 75 100 125 150 180 955 955 955 950 965 965 970 970 975 975 975 985 985 985 988 987 987 81.6 83.2 83.8 85.0 86.8 88.6 90.5 89.3 89.9 90.7 90.8 91.4 91.5 92.9 94.2 94.5 95.0 83.7 84.9 85.2 85.7 87.7 89.0 90.8 90.4 91.0 91.7 91.9 92.5 92.7 93.7 94.8 95.0 95.3 83.4 84.5 84.6 85.0 87.0 88.1 90.0 90.2 90.8 91.5 91.8 92.4 92.6 93.7 94.5 94.7 94.9 0.75 0.76 0.77 0.77 0.82 0.82 0.83 0.82 0.82 0.83 0.84 0.86 0.86 0.86 0.87 0.87 0.88 7.0 9.1 12.3 16.5 15.2 22 29 36 42.5 56 68 84 102 135 159 192 229 7.1 9.2 12.5 16.9 15.9 22.5 30 37 44 58 71 87 106 140 167 202 241 5.8 6.2 6.2 6.3 5.9 6.1 6.7 5.3 5.7 5.7 7.1 5.6 5.6 6.8 7.6 7.4 7.7 2.1 2.3 2.3 2.3 1.9 2.0 2.2 2.2 2.2 2.3 3.2 1.8 1.8 1.9 2.5 2.5 2.7 1.8 1.9 1.9 1.9 1.7 1.8 1.8 1.8 1.8 1.6 2.5 1.5 1.5 1.7 2.0 2.0 2.0

Cast iron frame

2.7 2.8 2.8 2.8 2.5 2.6 2.8 2.3 2.3 2.3 2.6 2.4 2.4 2.6 2.6 2.6 2.5 27 34 40 46 78 102 169 260 285 536 880 1350 1640 2200 3100 3600 4300 58 64 69 77 103 120 155 210 220 290 380 460 515 620 790 860 990

1)

AM 160M ZG AM 160L ZG AM 180L ZG AM 200L PG AM 200L RG AM 225M P AM 250M P AM 280S V AM 280M V AM AM AM AM 315S YE 315M YE 315M ZE 315L ZE

6 75 6 90 6 110 6 132

1)

1)

1) Temperature rise to class F * Higher output (progressive motor)

AEG Electric Motors - 2.1 e/2005 - page 40

Three-phase squirrel cage motors designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at 400V IN 380-420V Direct-on-line starting Starting Breakaway Pull-up current torque torque ratio ratio ratio IA/IN MA/MN MS/MN Pull-out torque ratio MK/MN Moment of inertia Weight

kW

HP

min-1

50%

75%

cos

100%

10-3 kgm2

kg

750 min-1 (8 poles)

AM 71Z AA AM 80Z AA AM 90S AA AM 90L BA AM 100L AA AM 100L BA AM 112M AA AM 132S ZA AM 132M ZA AM 160M YA AM 160M ZA AM 160L ZA AM 180L ZA 8 8 8 8 8 8 8 8 8 8 8 8 8 0.12 0.25 0.37 0.55 0.75 1.1 1.5 2.2 3 4 5.5 7.5 11 0.16 0.33 0.50 0.75 1.0 1.5 2.0 3.0 4.0 5.5 7.5 10.0 15 670 680 680 680 690 690 696 700 700 725 725 725 725 40 40 52 52 59 59 66 79.3 81.4 83.5 84.3 85.0 86.7 44 47 58 58 64 67 69 80.5 82.3 84.9 85.6 86.3 87.8 49 51 59 59 65 68 70 79.0 80.5 84.5 85.2 85.8 86.9 0.51 0.62 0.53 0.54 0.65 0.62 0.66 0.72 0.72 0.72 0.72 0.73 0.73 0.7 1.1 1.7 2.5 2.6 3.9 4.6 5.70 7.50 9.40 12.9 17.4 25.0 0.75 1.2 1.8 2.7 2.8 4.0 4.8 5.90 7.90 10.1 14.0 18.2 25.5 2.4 2.2 2.1 2.1 3.0 3.0 4 4.2 4.3 4.8 4.8 4.8 4.6 2.5 1.8 1.4 1.4 1.6 1.9 1.8 1.7 1.7 1.7 1.7 1.7 2.1 2.4 1.9 1.3 1.3 1.5 1.3 2.0 1.6 1.6 1.6 1.6 1.6 1.4

Aluminium frame

2.5 2.0 1.6 1.6 1.7 1.4 2.4 2.1 2.1 2.3 2.3 2.3 1.9 0.90 1.97 3.18 4.78 6.72 15.93 16.70 27 34 78 90 110 215 6.3 8 11.4 15 17.6 22.6 35 43 50 83 89 100 150

750 min-1 (8 poles)

AM 132S ZG AM 132M ZG AM 160M YG AM 160M ZG AM 160L ZG AM 180L ZG AM 200L RG AM 225S P AM 225M P AM 250M P AM 280S V AM 280M V AM AM AM AM 315S YE 315M YE 315M ZE 315L ZE 8 8 8 8 8 8 8 8 8 8 8 8 2.2 3 4 5.5 7.5 11 15 18.5 22 30 37 45 3.0 4.0 5.5 7.5 10.0 15 20 25 30 40 50 60 75 100 125 150 1) 700 700 725 725 725 725 730 730 730 730 740 740 738 738 738 738 79.3 81.4 83.5 84.3 85.0 86.7 87.2 88.6 88.7 88.7 91.1 91.1 92.2 93.2 93.4 93.5 80.5 82.3 84.9 85.6 86.3 87.8 88.8 89.9 89.9 90.2 92.3 92.4 93.0 94.0 94.2 94.3 79.0 80.5 84.5 85.2 85.8 86.9 88.5 89.5 89.5 90.2 92.2 92.3 92.7 93.8 94.0 94.1 0.72 0.72 0.72 0.72 0.73 0.73 0.76 0.77 0.77 0.78 0.81 0.81 0.82 0.82 0.82 0.82 5.70 7.50 9.40 12.9 17.4 25.0 32.0 39.0 46.6 61.0 74.0 90.0 105 142 169 206 5.90 7.90 10.1 14.0 18.2 25.5 33.5 41.0 48.0 65.0 74.0 90.0 112 150 179 218 4.2 4.3 4.8 4.8 4.8 4.6 5.3 5.2 5.6 6.5 6.0 6.0 6.1 6.1 6.2 6.4 1.7 1.7 1.7 1.7 1.7 2.1 2.3 2.3 2.5 3.2 2.1 2.1 2.2 2.4 2.5 2.7 1.6 1.6 1.6 1.6 1.6 1.4 1.9 1.9 2.0 2.5 1.7 1.7 1.7 1.8 1.8 1.8

Cast iron frame

2.1 2.1 2.3 2.3 2.3 1.9 2.5 2.2 2.3 2.6 2.3 2.3 2.3 2.1 2.1 2.1 27 34 78 90 110 215 285 438 538 1080 1520 1860 2200 3100 3600 4300 58 65 103 109 120 175 220 255 285 400 480 500 620 790 900 990

8 55 8 75 8 90 8 110

1)

1) Temperature rise to class F

AEG Electric Motors - 2.1 e/2005 - page 41

Three-phase squirrel cage motors Designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

High efficiency motors, efficiency values to CEMEP Voluntary Agreement

Type Rated output Rated speed Efficiency Power factor Rated current at IN

Temperature rise to class B

Direct-on-line-starting Starting Breakaway Pull-up Pull-out current torque torque torque ratio ratio ratio ratio IA/IN MA/MN MS/MN MK/MN Moment of inertia Weight

kW

HP

min-1

50%

75%

cos

100% 400V

380-420V

10-3 kgm2

kg

3000 min-1 (2 poles)

AMHE 80Z BA AMHE 90S AA AMHE 90L CA AMHE 100L AA 2 2 2 2 1.1 1.5 2.2 3 4 5.5 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 1.5 2 3 4 5.5 7.5 7.5 10 15 20 25 30 40 50 60 75 100 125 2880 2880 2860 2920 2940 2920 2900 2900 2930 2930 2930 2930 2945 2950 2950 2955 2975 2975 82.0 83.0 84.0 85.1 87.1 85.7 85.5 86.5 89.5 90.2 90.2 91.8 91.9 92.1 93.0 93.2 93.0 93.6 84.0 83.4 85.8 85.8 89.3 87.5 88.6 89.5 90.7 91.6 91.8 92.5 93.1 93.4 94.1 94.2 94.4 94.8 83.8 84.1 85.6 86.7 89.9 88.6 88.6 89.5 90.7 91.6 92.0 92.5 93.1 93.6 94.2 94.3 94.9 95.2 0.77 0.80 0.85 0.84 0.86 0.88 0.90 0.90 0.86 0.86 0.86 0.87 0.89 0.89 0.88 0.89 0.90 0.89 2.5 3.2 4.4 5.9 7.5 10.1 10 13.5 20.4 27.5 33.5 39.5 52.5 65 78 94 132 161 2.6 3.3 4.6 6.1 7.8 10.5 10.5 14 21 28 34.5 41 55 68 82 99 132 161 4.8 8.1 8.5 12.3 12.5 8.9 7.6 7.9 7.3 7.6 7.9 7.7 7.8 7.6 7.9 7.7 7.5 7.5 3.6 3.6 3.5 4.2 4.3 3.0 2.8 3 2.4 2.5 2.8 2.5 2.1 2.2 2.5 2.4 1.9 1.9 3.4 3.1 3.2 4.7 2.2 2.1 2.3 2.5 2.2 2.3 2.6 2.3 1.9 2 1.9 1.8 1.5 1.5 3.6 4.0 3.7 6.3 4.5 3.2 3.3 3.5 3.1 3.1 3.4 3.2 2.8 2.8 2.9 3 3.2 3.2 0.89 1.56 1.8 4.05 8.58 8.58 14 20.5 32 39 47 70 130 156 270 424 816 957 9.5 14 16 22.8 33.6 34 46 53 85 96 106 135 220 240 315 410 560 620

AMHE 112M AA 2 AMHE 112M BA 2 AMHE 132S ZA AMHE 132S TA 2 2

AMHE 160M YA 2 AMHE 160M ZA 2 AMHE 160L ZA 2 AMHE 180M ZA 2 AMHE 200L PG AMHE 200L RG AMHE 225M P AMHE 250M P AMHE 280S V AMHE 280M V 2 2 2 2 2 2

1500 min-1 (4 poles)

AMHE 90S AA AMHE 90L BA AMHE 100L AA AMHE 100L BA 4 4 4 4 1.1 1.5 2.2 3 4 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 1.5 2 3 4 5.5 7.5 10 15 20 25 30 40 50 60 75 100 125 1430 1430 1450 1440 1450 1450 1450 1460 1460 1460 1465 1465 1475 1475 1475 1485 1480 82.8 84.8 85.5 86.8 87.5 87.9 88.8 90.0 90.7 91.6 91.8 92.5 92.3 92.5 93.2 93.9 94.1 83.8 85.3 86.1 87.8 88.6 89.2 90.1 91.0 91.8 92.3 92.6 93.3 93.6 93.9 94.4 94.7 95.0 83.8 85.0 86.4 87.4 88.3 89.2 90.1 91.0 91.8 92.3 92.6 93.2 93.8 94.0 94.4 94.8 95.2 0.76 0.76 0.71 0.77 0.77 0.84 0.84 0.82 0.84 0.84 0.85 0.84 0.84 0.86 0.82 0.85 0.85 2.5 3.4 5.2 6.5 8.5 10.8 14.4 22 29 35 41 56.5 68 80.5 103 134 162 2.6 3.5 5.4 6.7 8.8 11.3 15 22.5 29.5 36 42.5 58.5 70.5 84.5 107 140 168 6.1 6.4 6 6.3 6.1 7.4 7.4 6.9 7.4 7.5 7.8 7 7.7 7.7 6.8 6.8 6.8 4.0 3.9 3.2 3.4 3.1 3 3 2.3 2.5 2.8 3 2.4 2.3 2.3 3.8 2.2 2.2 3.9 3.8 3.0 3.1 2.8 2.4 2.4 2.1 2.2 2.3 2.4 1.8 2 2 2.3 1.8 1.8 4.1 4.0 3.4 3.6 3.3 3.3 3.3 2.9 3.1 3.1 3.2 2.6 2.9 2.9 2.6 2.7 2.7 3.73 3.73 5.58 7.3 13.3 30 36 59 82 112 132 206 356 461 677 1060 1260 16.4 16.4 22.4 26.5 30.4 55 65 86 102 130 140 230 290 330 400 530 565

AMHE 112M AA 4 AMHE 132S RA 4 AMHE 132M TA 4 AMHE 160M ZA 4 AMHE 160L ZA 4 AMHE 180M ZA 4 AMHE 180L ZA 4 AMHE 200L RG AMHE 225S P AMHE 225M P AMHE 250M P AMHE 280S V AMHE 280M V 4 4 4 4 4 4

AEG Electric Motors - 2.1 e/2005 - page 42

Three-phase squirrel cage motors High efficiency according to EPAct

For mains voltage 460 V - 60 Hz

Verified by

Type

Underwriters Laboratories Inc.

Rated output Rated speed Efficiency Power factor Rated current at 460 V IN A

Thermal class F/B ­ S.F. 1.15

Direct-on-line-starting Starting Breakaway Pull-up Pull-out current torque torque torque ratio ratio ratio ratio IA/IN MA/MN MS/MN MK/MN Moment of inertia Weight

kW

HP

min-1

50%

75%

cos

100%

10-3 kgm2

kg

3600 min-1 (2 poles)

AMH 90S AA AMH 90L BA AMH 100L AA AMH 100L BA AMH 112M AA AMH 112M AA AMH 112M BA AMH 132S ZA AMH 132S TA AMH 132M TA AMH 160M YA AMH 160M ZA AMH 160L ZA AMH 180M ZA AMH 200L PG AMH 200L RG AMH 225M P AMH 250M P AMH 280S V AMH 280M V AMH 315S ZE AMH 315M YE 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1.5 2.2 2.2 3 3.7 4 5.5 5.5 7.5 9.2 11 15 18.5 22 30 37 45 55 75 90 2 3 3 4 5 5.5 7.5 7.5 10 12.4 15 20 25 30 40 50 60 75 100 125 150 200 3470 3500 3530 3525 3530 3540 3500 3520 3510 3520 3550 3545 3550 3550 3555 3555 3555 3560 3580 3580 3585 3585 83.8 85.4 86.5 86.4 86.1 86.1 85.0 86.1 89.7 88.8 90.1 91.2 91.5 92.1 90.6 91.7 91.8 91.2 92.8 93.0 93.3 94.5 84.9 86.6 87.9 87.8 88.4 88.3 88.6 88.2 90.1 89.9 91 89.9 92 92.6 91.7 92.5 93 92.7 93.2 94.1 94.4 94.8 84.3 86.3 87.8 87.7 88.1 88.0 88.5 88.5 89.5 89.5 91.0 91.0 91.7 92.4 91.7 92.4 93.0 93.0 93.6 94.5 94.5 95.0 0.88 0.84 0.84 0.82 0.84 0.87 0.85 0.87 0.91 0.91 0.88 0.88 0.87 0.88 0.87 0.88 0.88 0.90 0.89 0.89 0.89 0.90 2.7 3.9 3.9 5 6.3 6.6 9.3 9.2 11 14 17.3 23.5 28.8 33.5 47 57.5 70 81.5 110 134 165 220 7.7 7.5 11.5 10.5 14.3 13.7 10.9 7.9 8.1 8.1 8.7 8.7 8.9 8.6 8.1 7.9 8.1 7.5 7.6 7.7 8.2 8.7 3.1 4.4 4.7 5.6 5.7 5.3 4.5 3.3 3.4 3.3 2.8 2.8 2.8 2.9 2.4 2.3 2.4 2.9 2.2 2.2 2.8 3 3 4 4.1 5.3 2.1 1.9 2.48 2.9 2.9 2.9 2.2 2.2 2.2 2.3 1.8 1.7 1.8 1.7 1.7 1.7 1.5 1.6 3.6 4.4 5.5 5.8 5.8 5.4 4.3 3.7 3.9 3.9 3.6 3.6 3.6 3.7 2.9 2.7 3 2.5 3.4 3.4 3 3.2 1.56 1.8 3.35 4.05 8.58 8.58 8.58 20.5 20.5 25 39 47 52 88 130 156 270 424 816 957 1200 1600 14 16 19.7 22.8 33.6 33.6 34 53 53 59 96 104 115 145 220 240 315 410 560 620 810 1000

2 110 2 150

1800 min-1 (4 poles)

AMH 90L AA AMH 90L BA AMH 90L CA AMH 100L AA AMH 100L BA AMH 112M AA AMH 112M AA AMH 132S ZA AMH 132M ZA AMH 132M TA AMH 160M ZA AMH 160L ZA AMH 180M ZA AMH 180L ZA AMH 200L RG AMH 225S P AMH 225M P AMH 250M P AMH 280S V AMH 280M V AMH 315S ZE AMH 315L ZE 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 1.1 1.5 1.8 2.2 3 3.7 4 5.5 7.5 9.2 11 15 18.5 22 30 37 45 55 75 90 1.5 2 2.4 3 4 5 5.5 7.5 10 12.4 15 20 25 30 40 50 60 75 100 125 150 200 1745 1735 1720 1750 1740 1750 1745 1755 1750 1745 1770 1770 1770 1770 1780 1780 1780 1775 1785 1785 1785 1785 82.2 82.1 82.2 85.8 85.7 86.3 86.5 88.8 89.5 89.2 90.8 91.4 92.3 92.2 92.3 92.2 93.4 91.2 93.8 94.1 93.6 94.1 84.2 84.4 84.3 87.6 87.7 87.9 88.1 89.8 90.2 90 91.4 91.6 92.8 92.7 93.2 93.2 93.9 93.8 94.5 94.6 94.7 94.9 84.2 84.4 84.3 87.5 87.6 87.8 88.0 89.5 89.5 89.5 91.0 91.0 92.4 92.4 93.0 93.0 93.6 94.1 94.5 94.5 95.0 95.0 0.76 0.73 0.77 0.70 0.76 0.79 0.81 0.84 0.84 0.84 0.84 0.84 0.83 0.84 0.82 0.85 0.84 0.80 0.84 0.84 0.87 0.88 2.1 3.1 3.4 4.6 5.6 6.8 7 9.4 12.4 16 18.5 24 29 36.5 49 60 72 91 119 143 170 228 7.2 7.5 7.4 6.5 7.4 6.9 6.7 7.9 8.1 8.3 8.6 8.2 8.8 8.6 7.7 7.8 7.9 8.5 7.8 7.7 7.8 8 3.8 4 4.4 3.8 3 4.2 3.9 3.4 3.5 3.6 3.2 3.2 3.2 3.2 2.9 2.3 2.3 4.6 2.9 2.9 2.2 2.4 4 3.9 3.3 3.1 2.8 3.5 3.2 2.8 2.9 2.9 2.3 2.3 2.3 2.3 2.2 2 2 2.7 2.1 2.1 1.6 1.6 4.6 4.2 4 3.9 3.2 4.5 4.2 3.7 3.8 3.9 3.4 3.4 3.4 3.4 3 2.8 2.8 3.2 3.1 3.1 2.8 2.9 3.73 3.73 3.73 5.58 7.3 13.3 13.3 30 36 36 82 93 132 150 248 356 461 750 1060 1260 2200 3100 16.4 16.4 16.4 22.4 26.5 30.4 30.4 56 65 65 98 112 140 155 255 290 330 420 550 585 860 1120

4 110 4 150

AEG Electric Motors - 2.1 e/2005 - page 43

Pole-changing squirrel-cage motors designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at 400V IN 380-420V Direct-on-line starting Starting Breakaway current torque ratio ratio IA/IN MA/MN Moment of inertia Weight

kW

HP

min-1

100%

cos

10-3 kgm2

kg

1500/3000 min-1 (4/2 poles) - Dahlander connection /YY

AM 63Z AA AM 71Z AA AM 80Z AA AM 80Z BA AM 80Z CA AM 90L AA AM 90L BA 4/2 4/2 4/2 4/2 4/2 4/2 4/2 0.20/0.30 0.30/0.45 0.45/0.60 0.55/0.75 0.8/1.1 1.2/1.55 1.6/2.0 1) 1.8/2.5 2.2/3.0 2.6/3.3 3.3/4.4 4.7/6 6.4/7.8 8.7/10.7 12.5/16.5 15/19.5 17.5/23 24/29 26/33 30/38 34/46 50/58 60/72 70/84

1) 1)

0.27/0.40 0.40/0.65 0.65/0.80 0.75/1.0 1.1/1.5 1.6/2.1 2.15/2.7 2.5/3.35 3.0/4.0 3.5/4.4 4.4/5.9 6.4/8 8.7/10.5 11.7/14.5 17/22.5 20/26.5 24/31 32.5/39 35/45 40/52 46/63 68/79 82/98 1) 95/114 1) 116/156 136/170 163/204

1345/2700 56/65 1374/2830 61/66 1390/2760 64/68.8 1435/2850 70/71.2 1425/2830 76.1/77.2 1435/2850 77.4/78.3 1390/2810 73.5/75.5 1420/2865 78.5/77.4 1410/2830 74.6/71.4 1430/2890 82.6/78.6 1410/2800 77.4/75.4 1440/2880 85/83 1440/2900 86/85 1450/2925 88/89 1465/2940 89/90 1465/2955 89/87 1465/2950 90/88 1470/2955 91/89.5 1470/2955 91.5/89.5 1470/2965 92/91 1475/2960 92/91 1470/2965 93/92.5 1480/2975 94/93 1480/2975 94/93 1485/2970 94.5/93 1485/2970 95/94 1485/2970 95/94

0.65/0.81 0.78/0.73 0.75/0.80 0.67/0.77 0.70/0.79 0.71/0.79 0.78/0.86 0.76/0.84 0.72/0.82 0.78/0.76 0.82/0.85 0.83/0.88 0.84/0.89 0.83/0.85 0.84/0.85 0.80/0.88 0.81/0.86 0.83/0.89 0.84/0.91 0.85/0.91 0.85/0.90 0.85/0.90 0.85/0.91 0.85/0.91 0.86/0.91 0.87/0.91 0.87/0.91

0.8/0.83 1.0/1.35 1.4/1.6 1.7/2.0 2.2/2.6 3.2/3.7 4.0/4.6 4.5/5.6 5.9/7.4 5.9/8.0 7.5/9.9 9.7/12 13/15 17.5/21.5 25.5/32 30/36.5 34.5/43 46/52 50/59 55/66 63/81 92/100 108/122 126/142 150/195 175/210 210/255

0.89/0.88 1.2/1.5 1.5/1.7 1.8/2.1 2.5/2.8 3.4/3.9 4.1/4.7 4.7/5.8 6.1/7.7 6.1/8.5 7.8/10.6 10.2/12.8 13.5/16 18.5/22.5 27/34 31.5/38.5 36.5/46 48/55 52/62 58/70 66/85 96/104 114/129 133/150 156/203 182/217 219/264

2.4/3.2 3.3/3.0 3.8/4.0 4.5/5.0 4.5/4.9 4.7/5.1 4.1/5.5 5.2/5.5 4.2/4.3 4.7/5.5 4.5/5.1 5.3/6.0 5.5/6.7 6.4/7.3 6.8/7.5 5.8/7.2 6.5/7.5 6.2/7.8 6.4/7.9 5.8/7.8 6.6/7.8 5.8/8.6 5.9/8.5 5.9/8.5 6.0/7.4 6.6/7.9 6.6/7.9

2.1/2.1 2.3/2.1 2.3/2.2 2.6/2.8 2.5/2.7 2.6/2.7 2.7/2.6 2.2/2.2 1.8/2.0 1.9/2.2 2.1/2.4 2.1/2.1 2.2/2.3 2.0/2.2 2.2/2.4 2.0/1.8 2.0/1.8 2.1/2.5 2.0/2.2 1.7/1.8 1.9/1.8 3.0/3.5 2.0/2.2 2.0/2.2 1.6/1.5 1.7/1.6 1.7/1.6

0.40 0.76 1.58 2.00 2.41 3.10 3.73 4.60 4.60 5.58 13.30 22.00 30.00 59.00 82.00 112.0 132.0 206.0 248.0 356.0 428.0 750.0 1200.0 1400.0 2200.0 3100.0 3100.0

4.6 6.3 8.3 11.5 14.7 15.6 17.1 21.4 22.5 23.2 36.1 46 55 87 102 130 140 230 255 325 330 465 580 620 860 940 1120

1)

AM 100L AA 4/2 AM 100L BA 4/2 AM 100L CA 4/2 AM 112M AA 4/2 AM 132S ZA 4/2 AM 132M ZA 4/2 AM 160M ZA 4/2 AM 160L ZA 4/2 AM 180M ZA 4/2 AM 180L ZA 4/2 AM 200L PG AM 200L RG AM 225S P AM 225M P AM 250M P AM 280S V AM 280M V 4/2 4/2 4/2 4/2 4/2 4/2 4/2

1)

1)

AM 315S ZE 4/2 AM 315M ZE 4/2 AM 315L ZE 4/2

85/115 100/125 120/150

1) Temperature rise to class F

AEG Electric Motors - 2.1 e/2005 - page 44

Pole-changing squirrel-cage motors designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at 400V IN 380-420V Direct-on-line starting Starting Breakaway current torque ratio ratio IA/IN MA/MN Moment of inertia Weight

kW

HP

min-1

100%

cos

10-3 kgm2

kg

750/1500 min-1 (8/4 poles) - Dahlander connection /YY

AM 71Z AA AM 80Z AA AM 80Z BA AM 90S AA AM 90L BA 8/4 8/4 8/4 8/4 8/4 0.09/0.15 0.18/0.37 0.26/0.51 0.37/0.75 0.5/1.0 0.7/1.4 0.9/1.8 1/1.8 1.3/2.6 1.8/3.4 2.3/4.4 4/7.5 5.5/9 7.5/12.5 11/18 15/23 18/29 21/32 26/37 32/46 44/60 52/70 0.12/0.20 0.25/0.50 0.35/0.68 0.50/1.0 0.67/1.34 0.94/1.9 1.2/2.5 1) 1.34/2.5 1.75/3.0 2.5/4.6 3.1/6.0 5.5/10 7.5/12.2 10/17 15/24 20/31 24/39 28/43 35/50 43/63 60/82 71/95 610/1310 700/1370 700/1360 690/1385 690/1410 700/1440 690/1415 710/1445 705/1420 720/1410 720/1420 730/1455 725/1455 725/1460 730/1465 730/1465 735/1470 735/1475 735/1475 730/1470 740/1485 740/1485 735/1480 735/1480 735/1480 40/56 43.2/58.7 44.1/61.2 52.2/67.1 52.2/72.5 57.2/78.5 62/76 66.1/78.5 70.0/76.3 76/82 78/83 82/85.5 83/86.5 84/87.5 87/89 88/88 89/89 89/90 90/90 90/90.5 91/91 91/91 93/93 93/93 94/94 0.61/0.75 0.63/0.83 0.60/0.88 0.58/0.82 0.58/0.80 0.50/0.78 0.56/0.87 0.61/0.82 0.65/0.88 0.60/0.90 0.62/0.91 0.67/0.91 0.71/0.89 0.69/0.91 0.72/0.90 0.77/0.92 0.73/0.91 0.79/0.92 0.78/0.91 0.77/0.91 0.80/0.91 0.80/0.91 0.75/0.88 0.76/0.89 0.76/0.89 0.53/0.52 1.0/1.1 1.2/1.4 1.8/2.0 2.4/2.4 3.5/3.3 3.8/4.0 4.1/4.1 4.6/5.7 5.7/6.7 7/8.5 10.5/14 14/16.5 18.5/23 26/32 33.5/41 40/51 44/55 53/65 67/81 88/105 105/122 117/170 152/205 180/253 0.59/0.57 1.1/1.2 1.3/1.5 1.9/2.1 2.5/2.5 3.7/3.4 4.0/4.3 4.4/4.2 4.8/5.9 6/7.1 7.5/9 11.5/14.5 14.5/17.5 19.5/24 27/34 34/43 42/54 45/59 56/68 70/85 93/110 110/128 123/180 160/215 190/266 2.5/3.2 2.6/3.4 2.5/3.6 2.8/3.9 3.3/4.0 2.8/4.3 2.5/4.5 3.9/6.3 3.2/4.8 4.7/5.5 5.0/5.7 5.4/5.8 5.3/6.0 5.3/6.0 5.8/6.8 5.3/7.0 5.6/7.5 5.8/7.4 5.4/7.2 6.0/8.8 5.8/8.2 5.8/8.2 6.6/7.5 6.6/7.7 6.9/7.9 1.6/1.6 1.8/1.6 2.0/1.6 1.9/1.8 2.3/1.9 2.1/1.9 1.9/1.8 2.2/2.1 2.1/2.0 2.3/1.7 2.4/1.8 2.0/1.5 1.9/1.6 2.0/1.6 2.0/1.6 2.0/2.3 2.6/2.4 2.2/2.0 2.1/2.1 2.8/2.8 2.1/2.3 2.1/2.3 2.2/2.2 2.3/2.3 2.3/2.5 0.71 1.97 2.47 3.18 4.78 5.58 6.00 14.18 16.70 27.00 40.00 78.00 90.00 110.0 215.00 285.00 375.00 576.00 577.00 1320.0 2000.0 2320.0 3100.0 3600.0 4300.0 6.3 7.9 9.2 13.5 15.7 21.9 23.7 31.7 34.2 43 54 84 90 100 150 220 255 310 315 490 580 620 790 860 990

AM 100L AA 8/4 AM 100L BA 8/4 AM 112M AA 8/4 AM 112M BA 8/4 AM 132S ZA 8/4 AM 132M ZA 8/4 AM 160M YA 8/4 AM 160M ZA 8/4 AM 160L ZA 8/4 AM 180L ZA AM 200L PG AM 200L RG AM 225S P AM 225M P AM 250M P AM 280S V AM 280M V 8/4 8/4 8/4 8/4 8/4 8/4 8/4 8/4

1)

1)

1)

1)

1)

1)

1)

1) 1)

1) 1)

AM 315S ZE 8/4 AM 315M ZE 8/4 AM 315L ZE 8/4

60/100 75/120 90/150

82/136 100/163 120/200

1) Temperature rise to class F

AEG Electric Motors - 2.1 e/2005 - page 45

Pole-changing squirrel-cage motors designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at IN 400V 380-420V Direct-on-line starting Starting Breakaway current torque ratio ratio IA/IN MA/MN Moment of inertia

J

Weight

kW

HP

min-1

100%

cos

10-3 kgm2

kg

1500/1000 min-1 (4/6 poles) - separate windings

AM 71Z AA AM 80Z AA AM 80Z BA AM 90S AA AM 90L BA AM 100L AA AM 100L BA 4/6 4/6 4/6 4/6 4/6 4/6 4/6 0.22/0.15 0.37/0.26 0.55/0.37 0.75/0.5 1/0.65 1.2/0.8 1.6/1.0 1.8/1.3 2.6/1.85 3.1/2.2 4.9/3.2 7.5/5 9/6 12/8 16.5/11 21/14 26/18 30/21 37/25 45/30 65/45 80/54 87/58 95/65 105/72

1) 1)

0.30/0.20 1430/900 0.50/0.35 1385/905 0.75/0.50 1380/900 1.0/0.67 1400/930 1.34/0.87 1380/920 1.6/1.07 1460/940 2.15/1.34 1445/935 2.5/1.75 3.5/2.5 4/3 6.7/4.3 10/6.8 12.2/8 16/11 22.5/15 28/19 35/24 40/28 50/34 60/40 88/60 109/73 117/78 129/88 141/96 1445/950 1445/950 1440/965 1440/965 1460/980 1465/980 1465/980 1475/985 1470/980 1475/985 1475/985 1475/985 1475/980 1485/988 1485/988 1480/985 1480/985 1480/985

61/44 61.4/48.1 60.5/51.1 63/64 68.8/67.1 76.0/67.9 77.6/69.5 74.6/69.5 73.8/71.6 80/78 83/80 85.5/83 85.5/84 86.5/85 89/86 88/87 89.5/88.5 91/89 90.5/89 91/90.5 91.5/92 91.5/91 93/93 93/93 94/94

0.7/0.64 0.82/0.80 0.64/0.82 0.81/0.61 0.81/0.62 0.66/0.70 0.73/0.63 0.85/0.78 0.86/0.73

0.78/0.68 1.1/1.0 1.5/1.3 2.2/1.9 2.6/2.3 3.5/2.5 4.1/3.3 4.2/3.6 6.0/5.2

0.83/0.73 1.1/1.1 1.6/1.4 2.3/2.1 2.8/2.5 3.8/2.6 4.3/3.5 4.4/3.7 6.2/5.4 7.5/6 10.5/8 16.5/12 18.5/14 24/18 32.5/25.5 41/30 50/38 56/44 69/51 83/59 123/90 151/110 157/110 171/124 183/135

1.9/3.4 3.7/2.6 3.7/2.7 3.0/3.5 2.9/3.4 4.7/3.0 5.8/3.0 5.9/3.8 6.1/4.4 5.8/5.6 6.3/5.9 5.8/6.2 5.8/6.2 6.0/6.3 7.6/7.8 6.0/6.4 7.2/7.4 6.8/7.4 6.2/6.8 8.5/7.6 7.0/6.8 7.0/6.8 7.8/7.8 7.8/7.8 7.8/8.0

1.5/1.8 1.7/1.3 1.6/1.2 1.4/1.8 1.1/1.6 2.1/1.5 2.8/1.7 1.9/1.3 2.0/1.7 2.1/2.0 2.2/2.1 1,6/1,8 1.6/1.8 1.7/1.9 2.0/2.4 1.8/2.2 2.0/2.5 1.9/2.6 1.8/2.2

0.73 1.97 2.47 4.10 4.78 4.60 5.58 14.18 17.53 27.00 40.00 78.00 90.00 110.0 215.0 285.0 375.0 583.0 583.0

6.2 8.3 10.0 13.4 16.4 24.4 33.2 33.3 37.0 43 54 84 90 100 150 220 255 310 315 490 580 620 790 860 990

AM 112M AA 4/6 AM 112M BA 4/6 AM 132S ZA 4/6 AM 132M ZA 4/6 AM 160M YA 4/6 AM 160M ZA 4/6 AM 160L ZA 4/6 AM 180L ZA AM 200L PG AM 200L RG AM 225S P AM 225M P AM 250M P AM 280S V AM 280M V 4/6 4/6 4/6 4/6 4/6 4/6 4/6 4/6

0.81/0.74 7/5.5 0.84/0.77 10/7.5 0.83/0.77 15.6/11.4 0.86/0.77 17.6/13.3 0.86/0.79 22.8/17 0.87/0.76 31/24 0.88/0.81 39/28,5 0.88/0.81 48/36 0.89/0.81 53/42 0.90/0.83 66/49 0.90/0.86 79/56 0.88/0.83 117/86 0.88/0.83 144/105 0.90/0.85 150/105 0.90/0.85 165/118 0.93/0.87 175/127

1)

2.8/3.0 1320.0 1.7/2.3 1200.0 1.7/2.3 1400.0 1.9/2.2 3100.0 2.0/2.2 3600.0 2.0/2.3 4300.0

AM 315S ZE 4/6 AM 315M ZE 4/6 AM 315L ZE 4/6

1) Temperature rise to class F

AEG Electric Motors - 2.1 e/2005 - page 46

Pole-changing squirrel-cage motors designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Temperature rise to class B

Type Rated output Rated speed Efficiency Power factor Rated current at IN 400V 380-420V Direct-on-line starting Starting Breakaway current torque ratio ratio IA/IN MA/MN Moment of inertia

J

Weight

kW

HP

min-1

100%

cos

10-3 kgm2

kg

1000/750 min-1 (6/8 poles) - separate windings

AM 80Z AA AM 90L AA AM 100L AA 6/8 6/8 6/8 0.37/0.18 0.55/0.30 0.75/0.45 0.95/0.65 1.5/0.75 1.6/1.3 2.9/2.2 4/3 5.5/4 7.5/5.5 11/8.5 15/11.5 19/14.5 23/18 28/21 31/24 44/33 55/42 65/48 75/55 90/70

1) 1)

0.50/0.25 0.75/0.40 1.0/0.60 1.3/0.90 2.0/1.0 2.2/1.8 3.9/3 5.5/4 7.5/5.5 10/7.5 15/11.5 20/15.6 26/19.7 31/24 38/28 42/32.5 59.5/45 75/57 87/64 100/74 120/94

915/700 950/710 960/720 965/715 970/720 965/715 965/715 980/730 975/725 980/725 985/730 980/735 980/735 985/735 985/735 985/735 988/738 988/738 988/740 988/740 988/740

51.1/44.2 65.2/45.1 72.6/61.8 65.2/62.1 75.3/64.6 78/75 81/77 82/77 83/78 84/79 86/83 88/86.5 89/86.5 89/88 90/88.5 91/91 91/90 91/90 92.0/92.0 92.5/92.0 93.0/92.5

0.81/0.65 0.62/0.52 0.67/0.54 0.78/0.70 0.66/0.60 0.74/0.71 0.74/0.71 0.75/0.72 0.75/0.70 0.75/0.73 0.76/0.74 0.82/0.74 0.83/0.75 0.83/0.78 0.82/0.78 0.84/0.79 0.81/0.75 0.81/0.75 0.87/0.81 0.87/0.81 0.87/0.81

1.3/1.0 2.0/1.8 2.2/2.0 3.0/2.2 4.4/2.8 4/3.5 7/5.8 9.3/7.6 12.5/10.5 17/14.5 24/20 30.5/25.5 37/32 45/38 54/45 59/49 87/70 108/90 117/90 135/105 160/135

1.4/1.0 2.1/1.9 2.3/2.1 3.2/2.3 4.6/3.0 4.5/3.8 7.5/6.3 9.8/8.5 13/11 18/15 26/22 32/27 39/34 47/40 57/47 62/51 91/74 113/95 121/94 140/109 166/140

2.8/2.5 3.9/2.6 4.1/2.9 4.5/3.8 4.6/3.8 5.3/4.4 5.8/4.7 5.4/3.8 5.4/3.8 5.5/3.8 6.8/5.5 5.8/4.8 6.0/5.5 6.2/5.2 5.8/5.0 8.4/7.5 5.2/5.0 5.2/5.0 7.5/7.4 7.5/7.4 7.5/7.5

1.4/1.7 2.5/1.9 1.9/1.9 1.4/1.7 2.2/2.1 1.6/1.6 1.7/1.7 1.9/1.8 1.9/1.9 2.0/2.1 2.0/2.1 1.8/2.3 1.9/2.3 1.9/2.0 1.9/1.9

2.47 4.78 6.73 14.18 18.70 27.00 40.00 78.00 90.00 110.0 215.0 285.0 375.0 583.0 583.0

9.5 16.2 23.4 32.0 36.2 43 54 84 90 100 150 220 255 310 315 490 580 620 790 860 9900

AM 112M AA 6/8 AM 112M BA 6/8 AM 132S ZA 6/8 AM 132M ZA 6/8 AM 160M YA 6/8 AM 160M ZA 6/8 AM 160L ZA 6/8 AM 180L ZA AM 200L PG AM 200L RG AM 225S P AM 225M P AM 250M P AM 280S V AM 280M V 6/8 6/8 6/8 6/8 6/8 6/8 6/8 6/8

1)

2.6/3.4 1320.0 1.4/1.7 1200.0 1.5/2.1 1400.0 2.0/2.2 3100.0 2.1/2.3 3600.0 2.2 4300.0

AM 315S ZE 6/8 AM 315M ZE 6/8 AM 315L ZE 6/8

1) Temperature rise to class F

AEG Electric Motors - 2.1 e/2005 - page 47

Pole-changing squirrel-cage motors for fan drives designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Type

Temp. class

Rated output

Rated speed

Efficiency

Power factor

Rated current at IN 400V 380-420V

kW

HP

min-1

100%

cos

Direct-on-line starting Starting Breakaway current torque ratio ratio IA/IN MA/MN

Moment of inertia

J

Weight

10-3 kgm2

kg

1500/3000 min-1 (4/2 poles) - Dahlander connection Y/YY

AMV 63Z AA AMV 71Z AA AMV 71Z BA AMV 80Z AA AMV 80Z BA AMV 90L AA AMV 90L BA AMV 100L AA AMV 100L BA 4/2 4/2 4/2 4/2 4/2 4/2 4/2 4/2 4/2 B B B F B B B B B B B B F B F B F B F B F B F B F B F

1)

0.07/0.33 0.08/0.37 0.12/0.55 0.15/0.75 0.22/1.1 0.30/1.5 0.44/2.2 0.50/2.5 0.60/3.0 0.75/3.70 0.9/4.5 1.2/6 1.5/7 1.6/8 1.85/9 2.8/11 3.3/13.5 4/16.5 4.4/18.5 5/20 5.5/22.5 6/24 6.8/27 6.5/30 7/34 7/35 7.8/39 8.0/40 9.2/46 11.0/55 12.5/60 13/67 15/75 16/80 18/90 20/100 22/110 23/120 26/132 28/145 32/160

0.095/0.45 1350/2700 0.11/0.5 0.16/0.75 0.2/1.0 0.3/1.5 0.4/2.0 0.6/3.0 0.67/3.3 0.8/4.0 1.0/5.0 1.2/6.1 1.6/8 2/9.5 2.1/10.6 2.5/12 3.8/14.7 4.4/18 5.5/22.1 5.9/24.5 6.7/27 7.5/30 8/32 9/36 8/40 9.5/45 9.5/47 10.5/52 10.7/54 12.3/62 14.7/75 17/80 17/90 20/100 21/107 24/120 27/134 30/150 31/160 35/175 38/195 43/215 1350/2870 1430/2835 1400/2710 1420/2820 1400/2830 1430/2830 1430/2840 1440/2850 1440/2850 1440/2850 1455/2880 1445/2870 1455/2890 1445/2870 1450/2925 1440/2915 1470/2940 1465/2930 1470/2950 1465/2940 1470/2940 1465/2930 1480/2950 1475/2940 1480/2950 1475/2940 1485/2970 1480/2960 1485/2965 1480/2955 1485/2980 1480/2975 1485/2980 1485/2975 1492/2975 1490/2970 1492/2975 1490/2970 1492/2975 1490/2970

55/60 60/64 70/68 70/68 70/73 69/70 74/72 72/73 78/77 74/72 75/73 84.5/83 84/83 86.5/85 86/84.5 86.5/86 86/85 88.5/88 88/87.5 89/88 88.5/87 90/89 89/88 91.5/90 91/89 91.5/90 91/89 92/91 92/91 93/92.5 92.5/92 93.5/93 93.5/93 93.5/93 93.5/93 93.5/93 93.5/93 94.5/94 94.5/94 94.5/94 94.5/94

0.70/0.80 0.65/0.68 0.65/0.72 0.68/0.80 0.75/0.84 0.70/0.84 0.76/0.89 0.77/0.88 0.79/0.87 0.80/0.90 0.82/0.90 0.81/0.88 0.83/0.89 0.82/0.89 0.84/0.90 0.84/0.85 0.85/0.86 0.82/0.85 0.83/0.86 0.83/0.89 0.84/0.90 0.83/0.88 0.84/0.89 0.81/0.89 0.82/0.90 0.82/0.89 0.83/0.90 0.81/0.89 0.82/0.91 0.82/0.92 0.83/0.92 0.83/0.88 0.84/0.89 0.83/0.88 0.84/0.89 0.84/0.90 0.85/0.91 0.84/0.90 0.85/0.91 0.84/0.90 0.85/0.91

0.25/0.95 0.30/1.3 0.40/1.6 0.45/1.9 0.6/2.5 0.9/3.5 1.1/4.8 1.3/5.3 1.3/6.2 1.7/7.9 2.0/9.5 2.6/12 3.2/14 3.3/15.3 3.7/17.2 5.5/22.5 6.5/27 8.5/32.5 9.5/36 10/37.5 11/42 11.5/45 13.2/51 12.2/53 13.2/60 14/62 15.6/69 15.5/70 17.5/80 21/92 24/100 24.5/118 28/131 29.5/140 33/157 37/174 40/190 42/207 47/225 51/250 58/275

0.27/1.1 0.35/1.4 0.42/1.7 0.45/2.0 0.65/2.6 1.0/3.7 1.2/5.0 1.4/5.6 1.4/6.5 1.9/2.2 2.1/9.8 2.8/12.5 3.4/14.5 3.5/15.8 3.9/18 5.8/23 6.8/27.5 8.8/33 10/36.5 10.5/38.5 11.5/43 13/47 13.8/53 12.6/55 13.7/62 14.8/64 16.5/71 16.1/73 18.2/83 22/96 25/103 26/122 30/136 32/144 36/162 39/180 42/196 45/213 50/232 54/257 61/282

2.5/2.6 3.2/4.3 4.1/4.0 2.6/4.6 4.6/4.7 4.7/5.0 4.5/5.2 4.6/5.0 4.5/4.5 4.5/5.1 4.5/5.5 5.5/6.0 4.5/5.2 5.6/6.4 5.0/5.7 4.7/6.2 4.0/5.2 5.2/7.1 4.7/6.4 5.5/7.5 5.0/6.7 5.5/7.5 4.9/6.6 7.1/7.7 6.6/6.8 7.1/7.7 6.6/6.8 7.5/8.5 6.5/7.4 7.4/8.4 6.5/7.7 8.4/8.9 7.5/8.0 8.4/8.9 7.5/8.0 7.4/8.3 6.8/7.6 7.8/8.6 7.0/7.9 8.0/8.7 7.0/7.9

1.8/1.6 2.0/2.8 3/2.8 2.8/2.9 2.7/2.9 2.7/3.0 2.6/2.8 2.2/2.3 2.2/2.1 2.0/2.4 2.0/2.3 2.4/2.1 2.0/1.8 2.5/2.2 2.2/2.0 1.6/2.0 1.4/1.6 2.1/2.2 1.9/2.0 2.0/2.1 1.8/1.9 2.0/2.1 1.8/1.9 2.6/2.3 2.4/2.1 2.6/2.3 2.4/2.1 2.3/2.1 2.0/1.8 3.6/3.4 3.2/3.1 2.9/2.5 2.5/2.2 2.9/2.5 2.5/2.2 1.9/1.6 1.7/1.5 2.0/1.8 1.8/1.6 2.0/1.8 1.8/1.6

0.37 0.82 1.08 1.58 2.0 3.13 3.73 4.6 5.58 13.3 14.75 22.00 30.00

5.0 7.9 10.0 8.3 11.5 15.6 17.1 21.4 23.2 36.1 40.0 46 55

AMV 112M AA 4/2 AMV 112M BA 4/2 AMV 132S ZA 4/2

AMV 132M ZA 4/2

AMV 160M ZA 4/2 AMV 160L ZA 4/2

59.00 82.00

87 102

AMV 180M ZA 4/2 AMV 180L ZA 4/2

112.0 132.0

130 140

AMV 200L PG AMV 200L RG

4/2 4/2

206.0 248.0

230 255

AMV 225M P

4/2

B F B F B F B F B F B F B F

428.0

330

AMV 250M P

4/2

750.0

465

AMV 280S V AMV 280M V

4/2 4/2

1200.0 1400.0

580 620

AMV 315S ZE AMV 315M ZE AMV 315L ZE

4/2 4/2 4/2

2200.0 2500.0 3100.0

860 940 1120

1) Same mounting dimensions 225S Motors from frame size 132 upwards, with double marking

AEG Electric Motors - 2.1 e/2005 - page 48

Pole-changing squirrel-cage motors for fan drives designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Type

Temp. class

Rated output

Rated speed

Efficiency

Power factor

Rated current at IN 400V 380-420V

kW

HP

min-1

100%

cos

Direct-on-line starting Starting Breakaway current torque ratio ratio IA/IN MA/MN

Moment of inertia

J

Weight

10-3 kgm2

kg

750/1500 min-1 (8/4 poles) - Dahlander connection Y/YY

AMV 71Z AA AMV 80Z AA AMV 80Z BA AMV 90L AA AMV 90L CA AMV 100L AA AMV 100L BA 8/4 8/4 8/4 8/4 8/4 8/4 8/4 B B B B B F F F B B F B F B F B F B F B F B F B F

1)

0.08/0.37 0.12/0.55 0.18/0.75 0.18/1.1 0.4/1.6 0.45/2.2 0.6/2.6 0.7/3.3 1.0/4.0 1.4/4.6 1.5/5.5 1.7/6.4 2/7.5 2.2/9.2 2.5/10.2 3.5/14 4/15.5 4/17 4.5/19 5/20 5.5/22.5 6/24 6.5/27 7/28 8/32 8.5/36 11/44 11/46 12/50 16/66 18/74 19/78 21/86 26/105 29/115 33/132 36/145 40/165 44/180

0.11/0.5 0.16/0.75 0.25/1.0 0.25/1.5 0.54/2.15 0.60/3.0 0.80/3.5 0.94/4.5 1.34/5.5 1.9/6.2 2/7.5 2.3/8.7 2.7/10 3/12.5 3.3/13.7 4.7/19 5.5/21 5.5/23 6/25.5 6.8/27 7.5/30 8/32.5 8.5/36 9.5/38 10.5/43 11.5/49 15/60 15/62 16/88 22/88 24/100 26/106 28/115 35/140 39/155 45/177 48/194 55/220 59/240

660/1370 685/1420 660/1380 680/1400 675/1400 680/1420 680/1435 690/1420 720/1420 715/1450 705/1430 715/1450 705/1440 725/1465 720/1460 725/1465 720/1460 730/1465 715/1455 730/1470 725/1465 735/1480 730/1470 735/1480 730/1470 735/1480 725/1475 740/1475 735/1465 740/1485 735/1475 740/1485 735/1475 743/1480 740/1470 743/1480 740/1470 743/1480 740/1470

26/57 50/69 53/67 60/70 61.5/75

0.63/0.72 0.60/0.74 0.73/0.81 0.65/0.82 0.64/0.79

0.60/1.25 0.58/1.53 0.65/1.9 0.9/2.7 1.8/4.0 1.7/5.0 2.2/6.5 2.2/7.4 3.1/8.6 4.7/10.5 5.0/12.5 5.6/13.5 6.5/15.8 7/19.2 8/21.5 10/27.5 11.5/30.5 11.5/33 12.5/35.5 14.5/39 15.5/44 15.5/50 16.8/56 19/55 21.5/60 22/72 29/85 22/81 24/88 42/121 47/135 49/143 54/157

0.65/1.35 0.65/1.6 0.7/2.0 1.0/2.8 1.8/4.1 1.9/5.3 2.3/6.7 2.3/7.6 3.3/9.0 5/11 5.5/13 6/14.2 7/16.5 7.5/20.5 8.5/23 11/29 12.5/32 13/34.5 14/37 15/41 16/46 16.5/52 17.5/58 20/58 22.5/63 23/75 31/89 23/85 25/93 44/127 50/141 51/150 56/165 75/193 82/210 92/243 98/260 109/300 120/325

2.8/3.4 1.9/3.3 2.0/3.5 2.8/4.0 3.1/5.0 2.7/4.7 2.7/4.8 3.4/6.5 3.5/5.0 3.3/6.7 3.0/5.7 3.5/6.8 3.3/5.8 4.0/7.0 3.5/6.0 4.0/7.4 3.5/6.7 4.0/7.2 3.7/6.3 4.2/7.6 3.8/6.8 3.6/7.6 3.3/6.8 3.5/7.7 3.2/6.7 4.0/8.7 3.1/7.2 5.3/8.4 5.8/7.8 3.3/7.0 3.0/6.3 3.3/7.0 3.0/6.3 4.1/5.5 3.7/5.1 4.3/5.7 3.9/5.3 4.2/6.0 3.8/5.5

1.9/1.7 1.4/1.5 1.6/1.7 1.5/2.0 1.6/2.2 1.7/2.0 1.7/2.2 1.8/2.4 2.3/1.9 1.6/2.4 1.5/2.0 1.7/2.4 1.5/2.0 1.8/2.2 1.6/1.9 1.8/2.4 1.6/2.2 1.7/2.3 1.6/2.0 1.7/2.3 1.6/2.0 1.6/2.4 1.4/2.1 1.7/2.6 1.5/2.3 1.8/2.5 1.4/2.1 2.4/2.9 2.2/2.7 1.5/2.4 1.3/2.2 1.5/2.4 1.3/2.2 1.1/1.6 1.0/1.4 1.0/1.5 0.9/1.3 1.2/1.6 1.1/1.4

1.24 2.47 2.41 2.98 3.70 5.58 6.00 16.70 19.50 22.00 30.00

6.8 9.2 10.6 15.7 19.6 21.9 23.7 34.2 40.0 46 55

63.1/75.3 0.60/0.80 64.0/76.2 0.63/0.75 62/78 60/77 72/84 72/83 74/85 74/84 83/88 82/87 84/89 83/88 84/90 83/89 84/90 83/89 87.5/90.5 87/90 88/91 87/90.5 89.5/92 88.5/92 91.5/92 91/91 90/93 89.5/92 91/93 90/92 92.5/94.0 92/94 93.0/95.0 92.5/95 93.0/95.5 92.5/95 0.70/0.80 0.70/0.82 0.60/0.77 0.62/0.79 0.60/0.82 0.62/0.84 0.59/0.82 0.60/0.83 0.61/0.83 0.62/0.84 0.61/0.83 0.62/0.84 0.61/0.83 0.62/0.84 0.62/0.82 0.63/0.83 0.60/0.85 0.61/0.86 0.62/0.82 0.63/0.83 0.79/0.88 0.81/0.90 0.62/0.85 0.63/0.86 0.62/0.85 0.63/0.86

AMV 112M AA 8/4 AMV 112M CA 8/4 AMV 132SZA 8/4

AMV 132M ZA 8/4

AMV 160M ZA 8/4 AMV 160L ZA 8/4

59.00 82.00

87 102

AMV 180M ZA 8/4 AMV 180L ZA 8/4

112.0 132.0

130 140

AMV 200L PG AMV 200L RG

8/4 8/4

206 248

230 255

AMV 225M P

8/4

B F B F B F B F B F B F B F

430

330

AMV 250M P

8/4

1110

490

AMV 280S V AMV 280M V

8/4 8/4

1200 1400

580 620

AMV 315S ZE AMV 315M ZE AMV 315L ZE

8/4 8/4 8/4

0.60/0.87 68/185 0.61/0.88 76/200 0.60/0.87 85/230 0.61/0.88 93/250 0.61/0.88 103/285 0.62/0.89 113/310

1900 2500 3100

800 940 1120

1) Same mounting dimensions 225S Motors from frame size 132 upwards, with double marking

AEG Electric Motors - 2.1 e/2005 - page 49

Pole-changing squirrel-cage motors for fan drives designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Type

Temp. class

Rated output

Rated speed

Efficiency

Power factor

Rated current at IN 400V 380-420V

kW

HP

min-1

100%

cos

Direct-on-line starting Starting Breakaway current torque ratio ratio IA/IN MA/MN

Moment of inertia

J

Weight

10-3 kgm2

kg

1500/1000 min-1 (4/6 poles) - separate windings

AMV 71Z AA AMV 71Z BA AMV 80Z AA AMV 80Z BA AMV 90S AA AMV 90L BA AMV 90L CA AMV 100L AA AMV 100L BA 4/6 4/6 4/6 4/6 4/6 4/6 4/6 4/6 4/6 B F B B B B B B B B B F B F B F B F B F B F B F

1)

0.25/0.08 0.37/0.13 0.55/0.18 0.75/0.25 0.75/0.24 1.1/0.37 1.5/0.5 1.85/0.60 2.2/0.75 3/1.0 3.8/1.3 4.4/1.5 5.2/1.8 6/2 8/2.7 8.8/3 12/4 13.8/4.8 17/5.5 19/6 21/7 23.5/7.8 26/9 29/10 33/11 37/12 50/18 55/20 63/22 70/25 73/27 80/30 90/31 100/35 115/36 130/40 135/43 150/48

0.33/0.11 0.50/0.18 0.75/0.25 1.0/0.33 1.0/0.32 1.5/0.50 2.0/0.67 2.5/0.75 3.0/1.0 4.0/1.34 5/1.8 5.9/2 7/2.5 8/2.7 11/3.6 12/4 16/5.5 18.5/6.4 23/7.5 25.5/8 28/9.5 31.5/11 35/12 39/13.5 45/15 50/16 68/24 74/27 84/29 95/34 98/36 109/40 121/42 136/47 154/48 174/54 180/58 200/64

1370/900 1360/880 1380/920 1400/940 1400/950 1400/930 1420/950 1400/920 1420/950 1440/970 1450/970 1440/960 1450/970 1445/965 1465/985 1460/980 1465/985 1460/980 1470/975 1465/970 1470/985 1465/980 1475/985 1470/980 1475/985 1475/985 1470/985 1465/980 1490/992 1485/990 1490/992 1485/990 1492/995 1490/993 1492/995 1492/995 1490/993 1488/993

60/40 62/44 60/42 70/60 70/60 70/60 73/64 74/64 76/66 80/73 84/74 83/73 86/76 85/75 87/80 86/80 88/82 87/81 89.5/86 89/85 88/87 87.5/87 89.5/88 89/88.5 90/89 90.5/89 91/90 91/90 92.5/91 92.5/91 92.5/91 92/91 93/90.5 93/90 93/90.5 93/90 93.5/90 93.5/90

0.80/0.70 0.80/0.70 0.83/0.82 0.82/0.72 0.82/0.72 0.81/0.74 0.80/0.70 0.80/0.73 0.79/0.75 0.81/0.65 0.84/0.71 0.86/0.72 0.84/0.71 0.85/0.72 0.84/0.70 0.85/0.71 0.85/0.70 0.86/0.71 0.86/0.84 0.87/0.85 0.88/0.84 0.89/0.85 0.88/0.85 0.89/0.86 0.89/0.85 0.90/0.87 0.90/0.85 0.91/0.86 0.88/0.85 0.89/0.86 0.87/0.85 0.88/0.86 0.88/0.88 0.88/0.88 0.88/0.87 0.89/0.88 0.88/0.87 0.89/0.88

0.75/0.4 1.0/0.6 1.60/0.75 1.8/0.8 1.9/0.8 2.8/1.2 3.52/1.52 4.6/1.9 5.1/2.1 6.6/3.0 8/3.7 9.2/4.2 10.5/5 13.6/5.8 15.5/6.6 17.2/7.3 23/10 26.5/12 31/11 34.5/12 39/14 44/15.5 48/17 54/19 60/21 66/22.5 89/34.5 98/38 111/42 123/47 131/50 144/55 160/58 176/65 200/67 225/75 235/79 260/88

0.8/0.45 1.1/0.7 1.7/0.8 1.9/0.9 2.0/0.9 3.0/1.3 3.7/1.6 4.8/2.1 5.3/2.2 6.8/3.2 8.5/4 9.6/4.5 11/5.5 14/6.3 16/6.8 17.7/7.6 24.5/10.5 28.2/12.6 33/11.5 36/12.5 41/14.5 46/16 50/18 56/20 63/22 69/23.5 93/36 102/40 117/44 129/49 137/53 151/58 167/62 184/69 209/71 235/79 245/83 270/92

3.0/2.5 3.2/2.6 3.5/2.4 4.2/2.6 4.2/2.6 4.3/2.7 4.8/2.6 4.8/3.1 5.0/3.5 5.8/4.6 6.2/4.2 5.4/3.7 6.5/4.6 5.6/4.0 6.2/5.2 5.6/4.7 6.2/5.5 5.4/4.6 7.6/5.5 6.8/5.1 6.0/6.2 5.3/5.6 7.0/6.2 6.2/5.5 7.0/6.8 6.2/6.0 8.5/8.5 7.7/7.7 7.7/8.3 7.0/7.5 7.7/8.3 7.0/7.5 8.3/8.0 7.5/7.2 8.3/8.0 7.5/7.2 8.0/7.8 7.2/7.0

1.6/1.6 1.6/1.6 1.6/1.0 1.6/1.3 1.6/1.3 1.6/1.2 1.5/1.3 1.8/1.5 1.7/1.3 2.5/2.1 2.2/1.8 1.9/1.6 2.4/1.9 2.1/1.7 1.7/1.4 1.5/1.4 1.8/1.5 1.6/1.3 1.9/1.5 1.7/1.4 1.8/2.2 1.6/2.0 2.0/2.1 1.8/1.9 2.0/2.4 1.8/2.0 2.8/3.2 2.6/3.0 1.9/2.5 1.7/2.3 1.9/2.5 1.7/2.3 2.2/2.5 2.0/2.3 2.2/2.5 2.0/2.3 2.3/2.6 2.1/2.4

1.15 1.24 1.97 4.05 4.05 4.78 5.98 6.73 9.25 13.3 22.0 30.0

6.7 7.2 8.3 14 14 16.4 20.5 23.4 22.6 30.4 46 55

AMV 112M AA 4/6 AMV 132S ZA 4/6

AMV 132M ZA 4/6

AMV 160M ZA 4/6 AMV 160L ZA 4/6

59.0 82.0

87 102

AMV 180L ZA

4/6

215

150

AMV 200L PG AMV 200L RG

4/6 4/6

285 375

220 255

AMV 225M P

4/6

B F B F B F B F B F B F B F

583

315

AMV 250M P

4/6

1110

490

AMV 280S V AMV 280M V

4/6 4/6

1200 1400

580 620

AMV 315S ZE AMV 315M ZE AMV 315L ZE

4/6 4/6 4/6

3100 3600 4300

790 860 990

1) Same mounting dimensions 225S Motors from frame size 132 upwards, with double marking

AEG Electric Motors - 2.1 e/2005 - page 50

Pole-changing squirrel-cage motors for fan drives designed for range of rated voltage 380-420 V ± 5% - 50 Hz

For mains voltage to IEC 60038 400 V ± 10% - 50 Hz

Type

Temp. class

Rated output

Rated speed

Efficiency

Power factor

Rated current at IN 400V 380-420V

kW

HP

min-1

100%

cos

Direct-on-line starting Starting Breakaway current torque ratio ratio IA/IN MA/MN

Moment of inertia

J

Weight

10-3 kgm2

kg

1000/750 min-1 (6/8 poles) - separate windings

AMV 80Z AA AMV 80Z BA AMV 90L AA AMV 90L BA AMV 100L AA 6/8 6/8 6/8 6/8 6/8 B B B F B B B F B F B F B F B F B F B F B F B F B F B F B F B F B F B F B F 0.25/0.11 0.37/0.15 0.55/0.22 0.75/0.30 1.1/0.45 1.5/0.6 2.2/1 2.4/1.1 3/1.3 3.4/1.5 4/1.8 4.5/2 5.5/2.5 6.2/2.8 7/3.5 7.8/3.9 9/4.5 10/5 12/6 13.5/6.7 17/8.5 19/9.5 22/11 24.5/12.5 26/13 32/15 38/19 42/21 43/22 48/24 54/27 60/30 73/35 80/38 85/40 94/44 105/50 115/55 0.33/0.15 0.50/0.25 0.75/0.30 1.0/0.40 1.5/0.60 2.0/0.80 3/1.4 3.2/1.5 4/1.7 4.6/2 5.5/2.4 6/2.7 7.5/3.4 8.3/3.8 9.4/4.7 10.5/5.2 12/6 13.5/6.7 16/8 18/9 23/11.5 26/13 30/15 33/16.5 35/17.5 43/20 52/26 56/28 58/29 65/32.5 72/36 80/40 98/47 107/51 114/54 126/59 140/167 154/74 930/720 920/715 960/740 940/720 950/710 970/720 955/715 950/710 955/715 950/710 955/715 950/710 975/730 970/725 975/730 970/725 975/730 970/725 985/735 980/730 980/735 975/730 980/735 975/730 985/740 980/735 985/735 980/730 990/745 988/740 990/745 988/740 988/745 985/740 988/745 985/740 988/745 985/740 53/49 52/47 65/47 64/45.5 70.6/58 75.8/65 79/72 78/71 80/73 79/72 82/74 80/73 83/76 82/75 84/78 83/77 85/79 84/78 87/84 86/83 89/85 88/84 89.5/86 89/85 90.5/87 90/87 92/90 91/89 92/90 92/90 92/90 92/90 92.5/91 92/90 93/92 92/91 93.5/92 93/91.5 0.79/0.62 0.81/0.63 0.62/0.51 0.67/0.52 0.71/0.67 0.65/0.60 0.78/0.71 0.79/0.72 0.78/0.72 0.79/0.73 0.78/0.74 0.80/0.76 0.77/0.67 0.78/0.68 0.80/0.75 0.81/0.76 0.78/0.73 0.79/0.74 0.76/0.72 0.77/0.73 0.80/0.74 0.81/0.75 0.81/0.75 0.82/0.76 0.80/0.74 0.84/0.77 0.87/0.81 0.88/0.82 0.9/0.55 1.3/0.8 2.0/1.4 2.5/1.85 3.1/1.7 4.4/2.3 5.3/2.9 5.8/3.2 7.2/3.8 8.2/4.3 9.2/4.8 10.3/5.3 12.5/7 13.5/7.8 15/9 16.5/10 20/11 22/12.2 26/14.5 29/16 35/19.5 39/21.5 43/24.5 48/28 52/28.5 62/33 69/38 76/42 1.0/0.7 1.4/0.9 2.1/1.5 2.7/1.9 3.3/1.8 3.7/2.5 5.8/3.1 6.3/3.4 7.8/4.0 8.8/4.6 9.7/5.1 10.8/5.6 13/7.5 14/8.3 16/9.5 17.5/10.8 20.5/11.5 23/12.8 27.5/15 30.5/16.7 36.5/20.5 41/22.5 46/26 50/29.5 55/30 64/34 72/40 79/44 88/48 98/52 110/60 121/66 137/71 149/77 158/81 173/89 193/100 210/110 2.9/3.0 2.8/2.8 3.9/2.9 3.4/2.6 4.3/2.8 5.5/3.4 4.8/4.0 4.4/3.6 4.8/4.0 4.2/3.5 5.3/4.2 4.7/3.8 5.7/5.5 5.3/4.9 6.0/5.6 5.5/5.0 6.2/5.7 5.6/5.1 7.2/6.0 6.5/5.4 5.6/5.6 5.0/5.1 6.3/5.7 5.6/5.0 6.6/6.2 5.5/5.4 8.0/7.5 7.3/6.8 5.8/6.0 5.2/5.5 5.8/6.1 5.2/5.5 7.3/7.3 6.7/6.7 7.5/7.4 6.8/6.7 7.5/7.5 6.9/6.8 1.6/1.8 1.4/1.9 2.5/2.1 2.2/1.9 2.0/1.3 2.8/2.1 1.5/1.4 1.3/1.2 1.5/1.4 1.3/1.3 1.7/1.5 1.5/1.3 1.6/1.9 1.4/1.7 1.7/2.0 1.5/1.8 1.8/2.0 1.6/1.8 2.1/2.1 1.9/1.9 1.9/2.3 1.7/2.1 2.3/2.5 2.1/2.3 2.2/2.3 1.7/2.0 2.7/3.2 2.5/2.9 1.5/2.2 1.4/2.0 1.5/2.2 1.4/2.0 2.0/2.2 1.8/2.0 2.1/2.3 1.9/2.1 2.4/2.2 2.2/2.0 1.97 2.47 4.78 4.78 9.43 18.70 27.0 34.0 40.0 7.9 9.5 16.2 16.2 22.0 39.0 43 49 54

AMV 112M AA 6/8 AMV 132S ZA 6/8

AMV 132M YA 6/8 AMV 132M ZA 6/8

AMV 160M YA 6/8 AMV 160M ZA 6/8 AMV 160L ZA 6/8

78.0 90.0 110.0

84 90 100

AMV 180L ZA

6/8

215.0

150

AMV 200L PG AMV 200L RG

6/8 6/8

285 375

220 255

AMV 225M P

6/8 1)

583

315

AMV 250M P

6/8

1110

490

AMV 280S V AMV 280M V

6/8 6/8

0.80/0.77 84/46 0.81/0.78 93/50 0.80/0.77 104/57 0.81/0.78 115/63 0.87/0.81 0.88/0.82 0.87/0.81 0.88/0.82 0.87/0.82 0.88/0.83 130/68 142/74 150/77 165/85 185/95 202/105

1200 1400

580 620

AMV 315S ZE AMV 315M ZE AMV 315L ZE

6/8 6/8 6/8

3100 3600 4300

790 860 990

1) Same mounting dimensions 225S Motors from frame size 132 upwards, with double marking

AEG Electric Motors - 2.1 e/2005 - page 51

Frame size 56 - 180 IM B3

LC L AL AF s3 AD

DB

DA

GA

E

EA

D

AC

HD

F

AD

H HA

GD

K BC BB C B LB

BA

AA A AB CA

K1

Aluminium frame

IEC DIN 56Z AA, BA 63Z AA, BA, CA 71Z AA, BA, CA 80Z AA, BA, CA 90S AA, BA 90L CA, DA 100L AA, BA, CA 112M AA, BA, CA 132S AA, BA, YA, ZA 132M BA, CA, YA, ZA, RA 132M TA 160M XA, VA, ZA 160L RA, XA, ZA 180M RA, XA 180L RA, XA H h 56 63 71 80 90 90 100 112 132 132 132 160 160 180 180 A b 90 100 112 125 140 140 160 190 216 216 216 254 254 279 279 B a 71 80 90 100 100 125 140 140 140 178 178 210 254 241 279 C w1 36 40 45 50 56 56 63 70 89 89 89 108 108 121 121 K1) s 6 7 7 9 10 10 11 10 10 10 10 12 12 12 12 AB f 109 126 144 153 170 170 192 220 260 260 260 292 292 330 330 BB e 90 105 109 125 150 150 166 175 175 215 215 250 294 324 324 9.5 12.5 9.5 12.5 12.5 12.5 13 17.5 17.5 18.5 18.5 20 20 22.5 22.5 65 72 83 89 116 88 110 126 147.5 147.5 197.5 192 192 256 218 BC CA AD2) g4 98 103 112 129 138 138 145 161 198 198 198 246 246 266 266 HD2) m1 154 166 183 209 228 228 245 273 330 330 330 406 406 446 446 AC g 112 125 142 160 180 180 196 225 270 270 270 335 335 366 366 110 125 142 162 181 181 198 226 262 262 262 324 324 360 360 HC HA c 8 8 9 9.5 11 11 12 15 20 20 20 20 20 22 22 12 12 17 14 15 15 17 19 14 14 14 14 14 18 18 K1

IEC DIN 56Z AA, BA 63Z AA, BA, CA 71Z AA, BA, CA 80Z AA, BA, CA 90S AA, BA 90L CA, DA 100L AA, BA, CA 112M AA, BA, CA 132S AA, BA, YA, ZA 132M BA, CA, YA, ZA, RA 132M TA 160M XA, VA, ZA 160L RA, XA, ZA 180M RA, XA 180L RA, XA

L k 190 213 245 272 317 317 366 388 449.5 487.5 537.5 613 657 712 712

LB

LC k1

AL

AF

BA m

AA n 22 26 30 34.5 37 37 44 48 57.5 57.5 57.5 64 64 66 66

D/DA d/d1 9 11 14 19 24 24 28 28 38 38 38 42 42 48 48

E/EA l/l1 20 23 30 40 50 50 60 60 80 80 80 110 110 110 110

F/FA u/u1 3 4 5 6 8 8 8 8 10 10 10 12 12 14 14

HC

GD

GA/GC t/t1

DB

3)

d6/d7 M4 M4 M5 M6 M8 M8 M10 M10 M12 M12 M12 M16 M16 M16 M16

170 190 215 232 267 267 306 328 369.5 407.5 457.5 503 547 602 602

211 238 278 319 372 372 433 456 536.5 574.5 624.5 730 774 838 838

63 66 75 79 85 85 91 91.5 134 134 134 156 156 178.5 178.5

83 83 83 116 116 116 116 116 133 133 133 149 149 180 180

22 26 22 28.5 37/53 37/53 38 46 55 57.5 57.5 60 60 93 93

3 4 5 6 7 7 7 7 8 8 8 8 8 9 9

10.2 12.5 16 21.5 27 27 31 31 41 41 41 45 45 51.5 51.5

1) Clearance hole for screw 2) Maximum dimension 3) Centering holes in shaft extensions to DIN 332 part 2

AEG Electric Motors - 2.1 e/2005 - page 52

Frame size 132- 200 IM B3

LC L AL AF s3 AD

DB

DA

GA

E

EA

D

AC

HD

F

AD

H HA

GD

K BC BB C B LB

BA

AA A AB CA

K1

Cast iron frame

IEC DIN 132S YG, ZG 132M YG, ZG, RG 132M TG 160M VG, XG, ZG 160L RG, XG, ZG 180M RG, XG 180L RG, XG, ZG 200L LG, NG, PG, RG, FG H h 132 132 132 160 160 180 180 200 A b 216 216 216 254 254 279 279 318 B a 140 178 178 210 254 241 279 305 C w1 89 89 89 108 108 121 121 133 K1) s 10 10 10 12 12 12 12 16 AB f 260 260 260 304 304 330 330 380 BB e 175 215 215 290 290 324 324 360 17.5 18.5 18.5 18 18 22.5 22.5 22.5 185.5 147.5 197.5 226 192 256 218 237 BC CA AD2) g4 201 201 201 250 250 290 290 341 HD2) m1 333 333 333 410 410 470 470 541 AC g 270 270 270 335 335 366 366 405 262 262 262 324 324 360 360 400 HC HA c 20 20 20 15 15 15 15 18 14 14 14 14 14 18 18 _ K1

IEC DIN 132S YG, ZG 132M YG, ZG, RG 132M TG 160M VG, XG, ZG 160L RG, XG, ZG 180M RG, XG 180L RG, XG, ZG 200L LG, NG, PG, RG, FG 1) 2) 3) 4)

L k 487.5 487.5 547.5 657 657 712 712 779

LB

LC k1

AL

4)

AF

BA m

AA n 60 60 60 70 70 66 66 79

D/DA d/d1 38 38 38 42 42 48 48 55

E/EA l/l1 80 80 80 110 110 110 110 110

F/FA u/u1 10 10 10 12 12 14 14 16

HC

GD

GA/GC t/t1

DB

3)

d6/d7 M12 M12 M12 M16 M16 M16 M16 M20

407.5 407.5 457.5 547 547 602 602 669

574.5 574.5 624.5 774 774 838 838 895

134 134 134 235 235 260.5 260.5 185.5

133 133 133 168 168 180 180 265

55 57.5 57.5 97 97 95 95 90

8 8 8 8 8 9 9 10

41 41 41 45 45 51.5 51.5 59

Clearance hole for screw Maximum dimension Centering holes in shaft extensions to DIN 332 part 2 Frame size 132 with terminal box on the left, AL = 222 Frame size 200 with terminal box on the left, AL = 385.5

AEG Electric Motors - 2.1 e/2005 - page 53

Frame size 225-315 IM B3

LC L AL AF s3 AD

DB

DA

GA

E

EA

D

AC

HD

F

AD

H HA

GD

K BC BB C B LB

BA

AA A AB CA

K1

Cast iron frame

No. of poles 225S N P 225M N, P 250M K N, P 280S T, V 280M T, V 315S YE 315S ZE 315M YE, ZE 315L YE, ZE 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 H h 225 225 225 225 250 250 280 280 280 280 315 315 315 315 315 315 315 315 A b 356 356 356 356 406 406 457 457 457 457 508 508 508 508 508 508 508 508 B a 286 286 311 311 349 349 368 368 419 419 406 406 406 406 457 457 508 508 C w1 149 149 149 149 168 168 190 190 190 190 216 216 216 216 216 216 216 216 K s 16 16 16 16 20 20 20 20 20 20 28 28 28 28 28 28 28 28

1)

AB f 420 420 420 420 500 500 560 560 560 560 630 630 630 630 630 630 630 630

BB e 375 375 293 293 425 425 450 450 500 500 547 547 547 547 547 547 598 598

BC

CA

AD g4

2)

HD2) m1 585 585 585 585 640 640 703 703 703 703 738 738 830 830 830 830 830 830

HC

AC g 463 463 463 463 516 516 506 506 506 506 506 506 620 620 620 620 620 620

HC

HA c

K1

L k

32 32 32 32 38 38 41 41 40.5 40.5 90 90 45 45 45 45 45 45

318 318 318 318 321 321 325 325 325 325 365 315 342 342 291 291 360 360

360 360 360 360 390 390 423 423 423 423 423 423 515 515 515 515 515 515

450 450 450 450 500 500 564 564 564 564 599 599 660 660 660 660 660 660

22 22 22 22 45 45 50 50 50 50 50 50 55 55 55 55 55 55

16 16 16 16 20 20 20 20 20 20 35 35 35 35 35 35 35 35

857.5 887.5 857.5 887.5 971.5 971.5 1037 1037 1088 1088 1117 1097 1094 1124 1094 1124 1214 1244

No. of poles 225S N P 225M N, P 250M K N, P 280S T, V 280M T, V 315S YE 315S ZE 315M YE, ZE 315L YE, ZE 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4

LB

LC k1

AL

AF

BA m

AA n 90 90 90 90 135 135 122 122 122 122 122 122 120 120 120 120 120 120

D d 55 60 55 60 60 65 65 75 65 75 65 80 65 80 65 80 65 80

DA d1 55 60 55 60 60 65 65 75 65 75 60 70 60 70 60 70 60 70

E l 110 140 110 140 140 140 140 140 140 140 140 170 140 170 140 170 140 170

EA l1 110 140 110 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140

F u 16 18 16 18 18 18 18 20 18 20 18 22 18 22 18 22 18 22

FA u1 16 18 16 18 18 18 18 20 18 20 18 20 18 20 18 20 18 20

GD

GA t

GC t1 59 64 59 64 64 69 69 79.5 69 79.5 64 74.5 64 74.5 64 74.5 64 74.5

DB 3) d6/d7 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20

747.5 747.5 747.5 747.5 831.5 831.5 897 897 948 948 977 927 954 954 954 954 1074 1074

973 1033 973 1033 1118 1118 1163 1163 1214 1214 1267 1247 1244 1274 1244 1274 1364 1394

304.5 304.5 304.5 304.5 342.5 342.5 374 374 399.5 399.5 399.5 399.5 218 218 218 218 218 218

265 265 265 265 265 265 265 265 265 265 265 265 285 285 285 285 285 285

95 95 95 95 120 120 135 135 135 135 135 135 100 100 100 100 100 100

11 11 10 11 11 11 11 12 11 12 11 14 11 14 11 14 11 14

59 64 59 64 64 69 69 79.5 69 79.5 69 85 69 85 69 85 69 85

1) Clearance hole for screw 2) Maximum dimension 3) Centering holes in shaft extensions to DIN 332 part 2

AEG Electric Motors - 2.1 e/2005 - page 54

LC L AL T AF AD

Frame size 56 - 180 IM B5, IM B35, IM V1

DB

GA

EA

D

DA

F

E

AC

GD

LA E LB AD

M HD AD HA H

P

N

K C B BB

BA CA

S

AA A AB

K1

Aluminium frame

IEC DIN 56Z AA, BA 63Z AA, BA, CA 71Z AA, BA, CA 80Z AA, BA, CA 90S AA, BA 90L CA, DA 100L AA, BA, CA 112M AA, BA, CA 132S AA, BA, YA, ZA 132M BA, CA, YA, ZA, RA 132M TA 160M XA, VA, ZA 160L RA, XA, ZA 180M RA, XA 180L RA, XA M e1 100 115 130 165 165 165 215 215 265 265 265 300 300 300 300 N b1 80 95 110 130 130 130 180 180 230 230 230 250 250 250 250 P a1 120 140 160 200 200 200 250 250 300 300 300 350 350 350 350 T f1 2.5 3 3.5 3.5 3.5 3.5 4 4 4 4 4 5 5 5 5 LA c1 5.5 10 10 10 12 12 14 11 12 12 12 13 13 13 13 S1) s1 M6 M8 M8 M10 M10 M10 M12 M12 M12 M12 M12 M16 M16 M16 M16 H h 56 63 71 80 90 90 100 112 132 132 132 160 160 180 180 A b 90 100 112 125 140 140 160 190 216 216 216 254 254 279 279 B a 71 80 90 100 100 125 140 140 140 178 178 210 254 241 279 C w1 36 40 45 50 56 56 63 70 89 89 89 108 108 121 121 K s 6 7 7 9 10 10 11 10 10 10 10 12 12 12 12 65 72 86 89 113 88 110 126 147.5 147.5 197.5 192 192 256 218 98 103 112 129 138 138 145 161 198 198 198 246 246 266 266 154 166 183 209 228 228 245 273 330 330 330 406 406 446 446 CA AD2) HD2) AC g 112 125 142 160 180 180 196 225 270 270 270 335 335 366 366

BC

HA c

HC

K1

L k

LB

LC k1

AL

AF

D/DA d/d1

E/EA l/l1 20 23 30 40 50 50 60 60 80 80 80 110 110 110 110

F/FA u/u1 3 4 5 6 8 8 8 8 10 10 10 12 12 14 14

GD

GA/GC DB3) t,t1 d6/d7 M4 M4 M5 M6 M8 M8 M10 M10 M12 M12 M12 M16 M16 M16 M16

56Z AA, BA 63Z AA, BA, CA 71Z AA, BA, CA 80Z AA, BA, CA 90S AA, BA 90L CA, DA 100L AA, BA, CA 112M AA, BA, CA 132S AA, BA, YA, ZA 132M BA, CA, YA, ZA, RA 132M TA 160M XA, VA, ZA 160L RA, XA, ZA 180M RA, XA 180L RA, XA

9.5 12.5 9.5 12.5 25 12.5 13 17.5 17.5 18.5 18.5 20 20 22.5 22.5

8 8 9 9.5 11 11 12 15 20 20 20 20 20 22 22

110 125 142 162 181 181 198 226 262 262 262 324 324 360 360

12 12 17 14 15 15 17 19 14 14 14 14 14 18 18

190 213 245 272 317 317 366 388 449.5 487.5 537.5 613 657 712 712

170 190 215 232 267 267 306 328 369.5 407.5 457.5 503 547 602 602

211 238 278 319 372 372 433 456 536.5 574.5 624.5 730 774 838 838

63 66 75 79 85 85 91 91.5 134 134 134 156 156 178.5 178.5

89 89 89 116 116 116 116 116 133 133 133 149 149 180 180

9 11 14 19 24 24 28 28 38 38 38 42 42 48 48

3 4 5 6 7 7 7 7 8 8 8 8 8 9 9

10.2 12.5 16 21.5 27 27 31 31 41 41 41 45 45 51.5 51.5

1) Clearance hole for screw 2) Maximum dimension 3) Centering holes in shaft extensions to DIN 332 part 2

AEG Electric Motors - 2.1 e/2005 - page 55

LC L AL T AF AD

Frame size 132 - 200 IM B5, IM B35, IM V1

DB

GA

EA

D

DA

F

E

AC

GD

LA E LB AD

M HD AD HA H

P

N

K C B BB

BA CA

S

AA A AB

K1

Cast iron frame

IEC DIN 132S YG, ZG 132M YG, ZG, RG 132M TG 160M VG, XG, ZG 160L RG, XG, ZG 180M RG, XG 180L RG, XG, ZG 200L LG, NG, PG, RG, FG M e1 265 265 265 300 300 300 300 350 N b1 230 230 230 250 250 250 250 300 P a1 300 300 300 350 350 350 350 400 T f1 4 4 4 5 5 5 5 5 LA c1 12 12 12 13 13 13 13 15 S1) s1 M12 M12 M12 M16 M16 M16 M16 M16 H h 132 132 132 160 160 180 180 200 A b 216 216 216 254 254 279 279 318 B a 140 178 178 210 254 241 279 305 C w1 89 89 89 108 108 121 121 133 K s 10 10 10 12 12 12 12 16 185.5 147.5 197.5 226 192 256 218 237 201 201 201 250 250 290 290 341 333 333 333 410 410 470 470 541 CA AD2) HD2) AC g 270 270 270 335 335 366 366 405

BC

HA c

HC

K1

L k

LB

LC k1

AL

AF

D/DA d/d1

E/EA l/l1 80 80 80 110 110 110 110 110

F/FA u/u1 10 10 10 12 12 14 14 16

GD

GA/GC DB3) t,t1 d6/d7 M12 M12 M12 M16 M16 M16 M16 M20

132S YG, ZG 132M YG, ZG, RG 132M TG 160M VG, XG, ZG 160L RG, XG, ZG 180M RG, XG 180L RG, XG, ZG 200L LG, NG, PG, RG, FG

17.5 18.5 18.5 18 18 22.5 22.5 27.5

20 20 20 15 15 15 15 18

262 262 262 324 324 360 360 400

14 14 14 14 14 18 18 _

487.5 487.5 537.5 657 657 712 712 779

407.5 407.5 457.5 547 547 602 602 669

574.5 574.5 624.5 774 774 838 838 895

134 134 134 235 235 260.5 260.5 185.5

133 133 133 168 168 180 180 265

38 38 38 42 42 48 48 55

8 8 8 8 8 9 9 9

41 41 41 45 45 51.5 51.5 59

1) Clearance hole for screw 2) Maximum dimension 3) Centering holes in shaft extensions to DIN 332 part 2

AEG Electric Motors - 2.1 e/2005 - page 56

LC L AL T AF AD

Frame size 225 - 315 IM B5, IM B35, IM V1

DB

GA

EA

D

F

E

DA AC

GD

M S

P

N

LA E LB

22.5

45

AD

HD

K C B BB BA CA

AD HA H

AA A AB

K1

Cast iron frame

No. of poles 225S N, P 225M N, P 250M K, N, P 280S T, V 280M T, V 315S YE 315S ZE 315M YE, ZE 315L YE, ZE * 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 M e1 400 400 400 400 500 500 500 500 500 500 600 600 600 600 600 600 600 600 N b1 350 350 350 350 450 450 450 450 450 450 550 550 550 550 550 550 550 550 P a1 450 450 450 450 550 550 550 550 550 550 660 660 660 660 660 660 660 660 T f1 5 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 LA c1 16 16 16 16 18 18 18 18 18 18 22 22 22 22 22 22 22 22

S1) s1 M16 M16 M16 M16 M16 M16 M16 M16 M16 M16 M20 M20 M20 M20 M20 M20 M20 M20

H h 225 225 225 225 250 250 280 280 280 280 315 315 315 315 315 315 315 315

A b 356 356 356 356 406 406 457 457 457 457 508 508 508 508 508 508 508 508

B a 286 286 311 311 349 349 368 368 419 419 406 406 406 406 457 457 508 508

C w1 149 149 149 149 168 168 190 190 190 190 216 216 216 216 216 216 216 216

K s 16 16 16 16 20 20 20 20 20 20 28 28 28 28 28 28 28 28

CA

HD2) m1

AC g 463 463 463 463 516 516 514 514 514 514 514 514 620 620 620 620 620 620

AD2) g4 360 360 360 360 390 390 423 423 423 423 423 423 515 515 515 515 515 515

HA c 22 22 22 22 45 45 50 50 50 50 50 50 55 55 55 55 55 55

K1

318 318 293 293 321 321 325 325 325 325 365 315 342 342 291 291 360 360

585 585 585 585 640 640 703 703 703 703 738 738 830 830 830 830 830 830

16 16 16 16 20 20 20 20 20 20 35 35 35 35 35 35 35 35

No. of poles 225S N, P 225M N, P 250MK, P 280S T, V 280M T, V 315S YE 315S ZE 315M YE, ZE 315L YE, ZE * 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4 2-4/2 4

L k 857.5 887.5 857.5 887.5 971.5 971.5 1037 1037 1088 1088 1117 1097 1094 1124 1094 1124 1214 1244

LB

LC k1 973 1033 973 1033 1118 1118 1163 1163 1214 1214 1267 1247 1244 1274 1244 1274 1364 1394

AL

AF

BC

D d 55 60 55 60 60 65 65 75 65 75 65 80 65 80 65 80 65 80

DA d1 55 60 55 60 60 65 65 75 65 75 60 70 60 70 60 70 60 70

E I 110 140 110 140 140 140 140 140 140 140 140 170 140 170 140 170 140 170

EA I1 110 140 110 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140

F u 16 18 16 18 18 18 18 20 18 20 18 22 18 22 18 22 18 22

FA u1 16 18 16 18 18 18 18 20 18 20 18 20 18 20 18 20 18 20

GD

GA t 59 64 59 64 64 69 69 79.5 69 79.5 69 85 69 85 69 85 69 85

GC t1 59 64 59 64 64 69 69 79.5 69 79.5 64 74.5 64 74.5 64 74.5 64 74.5

DB3) d6/d7 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20 M 20

747.5 747.5 747.5 747.5 831.5 831.5 897 897 948 948 977 927 954 954 954 954 1074 1074

304.5 304.5 304.5 304.5 342.5 342.5 374 374 399.5 399.5 399.5 399.5 218 218 218 218 218 218

265 265 265 265 265 265 265 265 265 265 265 265 285 285 285 285 285 285

32 32 32 32 38 38 41 41 40.5 40.5 90 90 45 45 45 45 45 45

11 11 10 11 11 11 11 12 11 12 11 14 11 14 11 14 11 14

1) Clearance hole for screw 2) Maximum dimension 3) Centering holes in shaft extensions to DIN 332 part 2 * IM B5 on request

AEG Electric Motors - 2.1 e/2005 - page 57

LC L AL T AF AD

Frame size 56 - 160 IM B14, IM B34

DB

GA

F

D

E

AC M

GD

P N

LA E LB AD

DA

EA

HD

K C B BB

BA CA

H HA

AD

S

AA A AB

K1

Aluminium frame

Small flange P N LA a1 b1 c1 56Z AA, BA 63Z AA, BA, CA 71Z AA, BA, CA 80Z AA, BA, CA 90S AA, BA 90L BA, CA, DA 100L AA, BA, CA 112M AA, BA, CA 80 90 105 120 140 140 160 160 50 60 70 80 95 95 110 110 130 130 130 180 180 8 10 10 10 10 12 12 12 12 12 M e1 65 75 85 100 115 115 130 130 165 165 165 215 215 T f1 3 2.5 2.5 3 3 3 3.5 3.5 3.5 3.5 3.5 4 4 S s1 M5 M5 M6 M6 M8 M8 M8 M8 M10 M10 M10 M12 M12 Large flange P N LA a1 b1 c1 105 120 140 160 160 160 200 200 250 250 250 300 300 70 80 95 110 110 110 130 130 180 180 180 230 230 8 8 8 8.5 9 9 12 12 12 12 12 12 12 M e1 85 100 115 130 130 130 165 165 215 215 215 265 265 T f1 2.5 2.5 2.5 3.5 3.5 3.5 3.5 3.5 4 4 4 5 5 S s1 M6 M6 M8 M8 M8 M8 M10 M10 M12 M12 M12 M16 M16 L k

LB 170 190 215 232 267 267 306 328

LC k1 211 238 278 319 372 372 433 456

AL 63 66 75 79 85 85 91

AF 89 89 89 116 116 116 116

D d 9 11 14 19 24 24 28 28 38 38 38 42 42

DA d1 9 11 14 19 24 24 28 28 38 38 38 42 42

BC 9.5 12.5 9.5 12.5 25 12.5 13 17.5 17.5 18.5 18.5 20 20

190 213 245 272 317 317 366 388

91.5 116 133 133 133 149 149

132S AA, BA, YA, ZA 200 132M BA,CA,YA,ZA,RA 200 132M TA 200 160M XA, VA, ZA 4) 160L RA, XA, ZA 4) 250 250

449.5 369.5 536.5 134 487.5 407.5 574.5 134 537.5 457.5 624.5 134 613 657 503 547 730 774 156 156

E I 56Z AA, BA 63Z AA, BA, CA 71Z AA, BA, CA 80Z AA, BA, CA 90S AA, BA 90L BA, CA, DA 100L AA, BA, CA 112M AA, BA, CA 20 23 30 40 50 50 60 60

EA l1 20 23 30 40 50 50 60 60 80 80 80

F u 3 4 5 6 8 8 8 8 10 10 10 12 12

FA u1 3 4 5 6 8 8 8 8 10 10 10 12 12

GD

GA

GC t/t1

DB3) H d6/d7 h 56 63 71 80 90 90

A b 90 100 112 125 140 140 160 190 216 216 216 254 254

B a 71 80 90 100 100 125 140 140 140 178 178 210 254

C w1 36 40 45 50 56 56 63 70 89 89 89 108 108

K1) s 6 7 7 9 10 10 11 10 10 10 10 12 12

AB f

BB e

CA

AD2) HD2) g4 m1 154 166 183 209 228 228 245 278 330 330 330 406 406

AC g 112 125 142 160 180 180 196 225 270 270 270 335 335

HC

HA c

K1

3 4 5 6 7 7 7 7 8 8 8 8 8

10.2 10.2 M4 12.5 12.5 M4 16 16 M5

109 90 126 105 144 109 153 125 170 150 170 150 192 166 220 175 260 175 260 215 260 215 292 250 292 294

65 72 86 89 113 88 110 126

98 103 112 129 138 138 145 161

110 125 142 9.5 181 181 198 226 262 262 262 324 324

8 8 9 14 11 11 12 15 20 20 20 20 20

12 12 17 14 15 15 17 19 14 14 14 14 14

21.5 21.5 M6 27 27 31 31 41 41 41 45 45 27 27 31 31 41 41 41 45 45 M8 M8

M10 100 M10 112 M12 132 M12 132 M12 132 M16 160 M16 160

132S AA, BA, YA, ZA 80 132M BA CA, YA, ZA, RA 80 132M TA 80 160M XA, VA, ZA 4) 160L RA, XA, ZA 4) 1) 2) 3) 4)

147.5 198 147.5 198 197.5 198 192 192 246 246

110 110 110 110

Clearance hole for screw Maximum dimension Centering holes in shaft extensions to DIN 332 part 2 Bearing drive end 6309 2Z C3

AEG Electric Motors - 2.1 e/2005 - page 58

LC L AL T AF AD

Frame size 132 - 160 IM B14, IM B34

DB

GA

F

D

E

AC M

GD

P N

LA E LB AD

DA

EA

HD

K C B BB

BA CA

H HA

AD

S

AA A AB

K1

Cast iron frame

Small flange P N LA a1 132S YG, ZG 132M YG, ZG, RG 132M TG 160M VG, XG, ZG 160L RG, XG, ZG 200 200 200 250 250 b1 130 130 130 180 180 c1 12 12 12 12 12 M e1 165 165 165 215 215 T f1 3.5 3.5 3.5 4 4 S s1 M10 M10 M10 M12 M12 Large flange P N LA a1 250 250 250 300 300 b1 180 180 180 230 230 c1 12 12 12 12 12 M e1 215 215 215 265 265 T f1 4 4 4 5 5 S s1 M12 M12 M12 M16 M16 L k

LB

LC k1

AL

AF

D d

DA d1 38 38 38 42 42

BC

449.5 369.5 536.5 134 487.5 407.5 574.5 134 537.5 457.5 624.5 134 613 657 503 547 730 774 235 235

133 133 133 168 168

38 38 38 42 42

17.5 18.5 18.5 18 18

E I 132S YG, ZG 132M YG, ZG, RG 132M TG 160M VG, XG, ZG 160L RG, XG, ZG 80 80 80

EA l1 80 80 80

F u 10 10 10 12 12

FA u1 10 10 10 12 12

GD

GA

GC t/t1

DB3) H d6/d7 h M12 132 M12 132 M12 132 M16 160 M16 160

A b 216 216 216 254 254

B a 140 178 178 210 254

C w1 89 89 89 108 108

K1) s 10 10 10 12 12

AB f

BB e

CA

AD2) HD2) g4 m1

AC g 270 270 270 335 335

HC

HA c

K1

8 8 8 8 8

41 41 41 45 45

41 41 41 45 45

260 175 260 215 260 215 304 290 304 290

185.5 201 333 147.5 201 333 197.5 201 333 226 192 250 410 250 410

262 262 262 324 324

20 20 20 15 15

14 14 14 14 14

110 110 110 110

1) Clearance hole for screw 2) Maximum dimension 3) Centering holes in shaft extensions to DIN 332 part 2

AEG Electric Motors - 2.1 e/2005 - page 59

No. e . . . . . t. . s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AEG Electric Motors - 2.1 e/2005 - page 60

Branches & Partners

Lafert GmbH AEG Electric Motors Stuttgarter Str. 10 D - 71032 Böblingen - Germany Tel. +49 / (0) 7031/410 73 - 0 Fax +49 / (0) 7031/410 73 - 50 [email protected] Lafert Moteurs S.A. L'Isle d'Abeau Parc de Chesnes 75, rue de Malacombe F - 38070 St. Quentin-Fallavier France Tel. +33 / 474 95 41 01 Fax +33 / 474 94 52 28 [email protected] Lafert N.A. (North America) 5620 Kennedy Road - Mississauga, Ontario L4Z 2A9 - Canada Tel. +1 / 800/661 6413 - 905/629 1939 Fax +1 / 905/629 2852 [email protected] Lafert Singapore Pte Ltd 48 Hillview Terrace #03-08 Hillview Building - Singapore 669269 Tel. +65 / 67630400 - 67620400 Fax +65 / 67630600 [email protected] AEG Electric Motors Ltd. Electra House - Electra Way Crewe, Cheshire CW1 6GL United Kingdom Phone +44 / (0) 1270 270 022 Fax +44 / (0) 1270 270 023 [email protected] Lafert Motores Eléctricos, S.L. Polígono Pignatelli, Nave 27 E - 50410 Cuarte de Huerva (Zaragoza) - Spain Tel. +34 / 976 503 822 Fax +34 / 976 504 199 [email protected]

Lafert Electric Motors (Australia) 1676 Centre Road AUS - Springvale VIC 3171 - Australia Tel. +61 / (03) 9546 7515 Fax +61 / (03) 9547 9396 [email protected]

Factories

AEG Electric Motors, S.A. P.I. Can Petit Carrer del Camí Font de les Canyes, 45 E - 08227 Terrassa (Barcelona) - Spain Tel. +34 / 93 7398 400 Fax +34 / 93 7398 401 [email protected] Lafert S.p.A. Via J.F. Kennedy, 43 I - 30027 San Donà di Piave Venezia - Italy Tel. +39 / 0421 229 611 Fax +39 / 0421 222 908 [email protected]

w w w. l a f e r t . c o m

Italiana di Comunicazione

Information

ENGLISH_TRIF_21e_100105

61 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

108749


You might also be interested in

BETA
Microsoft Word - ET pow 01012008
EMD10579-English
ENGLISH_TRIF_21e_100105