Read -J04759 text version

-J04759

REV. 2010-01-12

NOSTALGIC SADDLEBAG GUARD RAILS

GENERAL

Kit Number

91179-09, 91179-10 Loosely install the screw (C) through the saddlebag-tofender support bracket (B), through the saddlebag support (A) and through the inner hole of the saddlebag guard rail bracket. Install nut (D). Tighten finger-tight. NOTE Position the saddlebag guard rail as low as possible on the stock saddlebag guard and support assembly. 2. Install screws (6) and washers (5) through the clamp end of the saddlebag guard rail. Position clamp end around the upright of the saddlebag guard and install the clamp (3 or 4). Tighten screws finger-tight. Align the saddlebag guard rail (1 or 2) parallel to the bottom of the saddlebag and muffler. Tighten the cap screw (C) and locknut (D) to 15-20 ft-lb (20-27 Nm). Tighten the clamp screws (6) to 22 in-lb (2.5 Nm).

Models

For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).

The rider's safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a)

3.

4.

Kit Contents

See Figure 1 and Table 1.

NOTE The reflectors are location-specific. There are markings on the back of the reflector - "L BOTTOM" or "R BOTTOM". 5. Peel the backing from the base of the new reflector (7 or 8). Without touching the reflector to the saddlebag guard, position the reflector and press the reflector to the saddlebag guard above the clamp (3 or 4) and press for 30 seconds. After releasing pressure, avoid direct contact with the reflector for at least 20 minutes. Repeat all steps for the other side of the motorcycle.

REMOVAL

1. 2. 3. If desired, remove the saddlebags. Remove screws (C) and locknuts (D). Save for installation. Remove reflectors with fishing line or dental floss. Use a sawing motion to remove the adhesive. Clean the surface thoroughly with an equal mixture of isopropyl alcohol and distilled water. Allow the surface to dry thoroughly.

6.

INSTALLATION

1. See Figure 1. Position the correct saddlebag guard rail (1 or 2) over the saddlebag guard and support assembly (A).

NOTE For ease of use, move the saddlebag buckles to the highest hole on the strap. 7. Install the saddlebags, if removed.

-J04759

Many Harley-Davidson® Parts & Accessories are made of plastics and metals which can be recycled. Please dispose of materials responsibly.

1 of 2

SERVICE PARTS

is05454a

1 2 B C 5 6 D

7 8 3 4

A

Figure 1. Service Parts: Nostalgic Saddlebag Guard Rails Table 1. Service Parts Table Item 1 2 3 4 5 6 7 8 A B C D Description (Quantity) Saddlebag guard rail, right (kit 91179-09) Saddlebag guard rail, right (kit 91179-10) Saddlebag guard rail, left (kit 91179-09, not shown) Saddlebag guard rail, left (kit 91179-10, not shown) Clamp, right Clamp, left (not shown) Lockwasher (4) Screw (4) Reflector, right Reflector, left (not shown) Stock saddlebag guard and support assembly Stock saddlebag-to-fender support bracket Stock cap screw Stock nut Part Number 91209-09 91209-10 91185-09 91185-10 90937-04 90938-04 7069 94383-92T 59370-98 59371-98

Items mentioned in text, but not included in kit:

-J04759

2 of 2

Information

-J04759

2 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

1094710


You might also be interested in

BETA
-J04759