Read CHAPTER 25 Rev D NSWC-2011 text version

CHAPTER

25

REFERENCES

1. Abadzheva, R.N. et al., "Effects of Brake Fluid Components on Rubber," Khimiya i Tekhnologiya Topliv i Masel, No. 8, pp. 18-19 (Aug 1982). "A Practical Guide to Compressor Technology", Second Edition, Heinz P. Bloch, John Wiley & Sons, 2006 Anderson, A.E., "Wear of Brake Materials," in: Wear Control Handbook, M.B. Peterson and W.O. Winer, Eds., pp. 843-857, Am. Soc. Mech. Eng., New York (1980). Armstrong, E.L., W.R. Murphy and P.S. Wooding, "Evaluation of Water Accelerated Bearing Fatigue in Oil-Lubricated Ball Bearings," Lubrication Engineering, Vol. 34, No. 1, pp. 15-21 (1 Nov 1977). Bauer, P., M. Glickmon, and F. Iwatsuki, "Analytical Techniques for the Design of Seals for Use in Rocket Propulsion Systems," Volume 1, ITT Research Institute, Technical Report AFRPL-TR-65-61 (May 1965). Bayer R.G., A.T. Shalhey and A.R. Watson, "Designing for Zero Wear," Machine Design (9 January 1970). Bishop, F.E. and William M. Needleman, "The Effects of Fluid Contamination on Component Wear," Pall Corporation. Block, H. and D. Johnson, "Downtime Prompts Upgrading of Centrifugal Pumps," Chemical Engineering Magazine, pp. 35-38 (25 Nov 1985). Boone, Tony D., "Reliability Prediction Analysis for Mechanical Brake Systems," NAVAIR-SYSCOM Report (Aug 1981). INCOM International Inc., Quincy,

2.

3.

4.

5.

6.

7.

8.

9.

10. "Boston Gear Catalog" Catalog 100, Massachusetts 02171.

References

25-1

Revision D

11. Canterbury, Jack, and James D. Lowther, "Application of Dimensional Analysis to the Prediction of Mechanical Reliability," Naval Weapons Support Activity, Washington Navy Yard, Wash., D.C., Report ADAD35295 (September 1976). 12. Carson, Harold, Springs: Troubleshooting and Failure Analysis, Marcel Dekker, Inc., New York. (1983). 13. Cormier, K.R., "Helicopter Drive System R&M Design Guide," Division of United Technologies Corp., Stanford, CT 06602, Report ADAD69835 (April 1979). 14. "Engineering Guide to Spring Design" Associated Spring, Barnes Group INc., Form No. 515 (1981). 15. "Fabrication and Testing of Lightweight Hydraulic System Simulator Hardware Phase II," Report NADC-79024-60, prepared by Rockwell International, Columbus, Ohio, for Naval Air Systems Command, Washington, D.C. 16. Ferodo Limited, Friction Materials for Engineers, Stockport, England (1969). 17. Field, G.J., "Seals That Survive Heat," Machine Design (1 May 1975). 18. Hauser, D.L. et al., "Hardness Tester for Polyur," NASA Tech Briefs, Vol. 11, No. 6, p. 57 (1987). 19. Hindhede, U., et al, Machine Design Fundamentals, John Wiley & Sons, NY, 1983. 20. Ho, T.L., F.E. Kennedy and M.B. Peterson, "Evaluation of Materials and Design Modifications for Aircraft Brakes," NASA Report CR134896 (Jan 1975). 22. Howell, Glen W. and Terry M. Weathers, Aerospace Fluid Component Designers' Handbook, Volumes I and II, TRW Systems Group, Redondo Beach, CA prepared for Air Force Rocket Propulsion Laboratory, Edwards, CA, Report AD 874 542 and Report AD 874 543 (February 1970). 23. Hubert, Christopher J., John W. Beck and John H. Johnson, "A Model and the Methodology for Determining Wear Particle Generation Rate and Filter Efficiency in a Diesel Engine Using Ferrography," Society of Automotive Engineers Paper No. 821195 (1982). 24. Hudgens, R.D. and L.B. Feldhaus, "Diesel Engine Lube Filter Life Related to Oil Chemistry," Society of Automotive Engineers Paper No. 780974 (1978).

References

25-2

Revision D

25. Johnson, R.L. and K. Schoenherr, "Seal Wear," in: Wear Control Handbook, M.B. Peterson and W.O. Winer, Eds., Sect. 5, pp 727-754, American Society of Mechanical Engineers, New York, (1980). 26. Igor J. Karassik et al, Pump Handbook, McGraw-Hill Book Company, New York (1986). 27. May, K.D., "Advanced Valve Technology," National Aeronautics and Space Administration, NASA Report SP-5019 (February 1965). 28. MIL-HDBK-217, "Reliability Prediction of Electronic Equipment". 29. Minegishi, H. et al., "Prediction of Brake Pad Wear/Life by Means of Brake Severity Factor as Measured on a Data Logging System," SAE Paper 840358 (1984). 30. Mordkowitz, A., "Predicting Service Life for Zero Wear," Machine Design (10 January 1974). 31. Nagel, W.B., "Designing with Rubber," Machine Design (June 23, July 7, July 21, Aug 11, 1977). 32. Neale, M.J., Tribology Handbook, Butterworths, London. 33. Needleman, William M., "Filtration for Wear Control," in: Wear Control Handbook, M.B. Peterson and W.O. Winer, Eds., Sect. 4, pp 507-582, Americna Society of Mechanical Engineers, New York, (1980). 35. "Optimum Design of Helical Springs," Machine Design, (6 November 1980). 36. Orthwein, William C., Clutches and Brakes: Design and Selection, Marcel Dekker, Inc., New York (1986). 37. Rhee, S.K. and P.A. Thesier, "Effects of Surface Roughness of Brake Drums on Coefficient of Friction and Lining Wear," SAE Paper 720449 (1972). 38. Roack and Young, Formulas for Stress and Strain, McGraw-Hill Book Company, New York (1975). 39. Shigley, J.E., Mischke, C.R., Mechanical Engineering Design, McGraw-Hill Book Co., NY, 1989. 40. Spokas, R.B., "Clutch Friction Material Evaluation Procedures," SAE Paper 841066 (1984).

References

25-3

Revision D

41. "Standard Product Catalog," Catalog SPC 82, The Falk Corporation, Milwaukee, Wisconsin. 44. Sibley, L.B., "Rolling Bearings," in: Wear Control Handbook, M.B. Peterson and W.O. Winer, Eds., Sect. 5, pp 699-726, American Society of Mechanical Engineers, New York (1980). 45. Barron, Randall F., Revision of Wear Model for Stock Actuators, Engineering Model for Mechanical Wear (July 1987). 46. Fox, R.W., and A.T. McDonald, Introduction to Fluid Mechanics, John Wiley and Sons, New York (1978). 47. Machine Design, 1985 Fluid Power Reference Issue, Penton/IPC, Inc., (Sept. 19, 1985). 48. Kragelsky, I.V. and V.V. Alisin, Friction, Wear, and Lubrication, Vol. 2, pg. 30, Pergamon Press, London (1981). 49. Kuhlmann-Wildorf, D., "Parametric Theory of Adhesive Wear in Uni-Directional Sliding," Wear of Materials, pp. 402-413, American Society of Mechanical Engineers, New York (1983). 50. Bentley, R.M. and D.J. Duquette, "Environmental Considerations in Wear Processes," Fundamentals of Friction and Wear of Materials, pp. 291-329, American Society For Metals, Metals Park, Ohio (1981). 51. Sarkar, A.D., Wear of Metals, pp. 62-68, Pergamon Press, London (1976). 52. Lundberg, G. and A. Palmgren, "Dynamic Capacity of Rolling Bearings," Acta Polytechnica, No. 7 (1974). 53. Rumbarger, John H., "A Fatigue Life and Reliability Model for Gears," American Gear Manufacturers Association Report 229.16 (January 1972). 54. AGMA Standard for Surface Durability Formulas for Spiral Bevel Gear Teeth, American Gear Manufacturers Association Report 216.01 (January 1964). 55. AGMA Standard Nomenclature of Gear Tooth Failure Modes, American Gear Manufacturers Association Report 110.04 (August 1980). 56. Haviland, G.S., "Designing with Threaded ENGINEERING, Vol 105, No. 10, Oct 83. Fasteners", MECHANICAL

References

25-4

Revision D

57. Deutschman, A.D., et al, Machine Design; Theory and Practice, MacMillan Publishing Co, NY, 1975 58. Parmley, R.O., Mechanical Components Handbook, McGraw-Hill Book Co., NY, 1985. 59. Handbook H28, Nat'l Bureau of Stds, Govt Printing Office, Washington, DC, 1957. 60. Bickford, J.H., An Introduction to the Design and Behavior of Bolted Joints, Marcel Dekker, Inc., NY, 1990. 61. Handbook of Corrosion Data, ASM International, Metals Park, OH, 1990 62. Baumeister, T, et al, Mark's Standard Handbook for Mechanical Engineers, McGraw-Hill Book Company 63. Thomas Couplings Applications Manual 64. Bolam, J.R., "Coupling Alignment: The Reverse Indicator Method Simplified", P/PM Technology, July/Aug 90 65. Dvorak, P., "Sorting Out Flexible Couplings", Machine Design, 11 Aug 88 66. Robertson, R., and Smith, B., "Why Flexible Couplings Fail", Plant Engineering and Maintenance, Jun 89 67. Universal Joint & Driveshaft Design Manual, Series No. 7, Society of Automotive Engineers, Inc, Warrendale, Pa. 68. H. Wayne Beaty and James L. Kirtley, Jr., Electric Motor Handbook, McGraw-Hill Book Company 1998 69. Norman Yudewitz, "Predict Relay Life Reliably with Simple Empirical Equations", Electronic Design, February 1, 1979 70. "Validation of Gearbox Reliability Models from Test Data", Report No. 87-D-0075, October, 1987, Eagle Technology, Inc. 71. Dennis N. Pratt, "Investigation of Spline Coupling Wear", Report No. SY-51R-87, December 1987, Naval Air Warfare Center, Patuxent River, Maryland 72. Randall F. Barron, "Engineering Model for Mechanical Wear", Report No. CMLDCR-09-88, June 1988, Louisiana Tech University

References

25-5

Revision D

73. Dennis Pratt, "Results of Air Compressor Reliability Investigation", Report No. TM 88-38 SY, January 1989, Naval Air Warfare Center, Patuxent River, Maryland 74. D. Pratt, "Results of Gear Pump Reliability Investigation", Report No. TM 89-24 SY, February 1990, Naval Air Warfare Center, Patuxent River, Maryland 75. D. Pratt, "Results of Centrifugal Pump Reliability Investigation", Report No. TM 8969 SY, February 1990, Naval Air Warfare Center, Patuxent River, Maryland 76. D. Pratt, "Results of Pneumatic Impact Wrench Reliability Investigation", Report No. TM 90-88 SY, December 1990, Naval Air Warfare Center, Patuxent River, Maryland 77. Randall F. Barron and Herbert G. Tull, III, "Failure Rate Model for Aircraft Brakes and Clutches", Report No. DTRC-CMLD-CR-01-90, August 1990, Louisiana Tech University 78. Randall F. Barron and Herbert G. Tull, III, "Failure Rate Model for Aircraft Brakes and Clutches", Report No. NSWC-92/LO2, August 1992, Louisiana Tech University 78. CDNSWC, "Interim Reliability Report on the MC-2A Compressor Unit", January, 1992 79. D. Pratt, "Results of Air Force MC-2A Air Compressor Unit Reliability Investigation", Report No. TM 92-89 SY, March 1993, Naval Air Warfare Center, Patuxent River, Maryland 80. D. Pratt, "Results of Dayton 5A701 Linear Actuator Reliability Investigation", Report No. TM 93-89 SY, February, 1994, Naval Air Warfare Center, Patuxent River, Maryland 81. TD 84-3 R&M Data for Industrial Plants, A.P. Harris and Associates, 1984 82. Metals Handbook, American Society for Metals, 1985, ISBN 0-87170-188-X 83. Handbook of Chemistry and Physics, 86th Edition, CRC Press, 2005 84. Machinery's Handbook, 27th Edition, Industrial Press, 2004 85. Lev Nelik, "What Happens When a Pump No Longer Operates At Optimum Conditions", Pumps and Systems, February 2005 86. "Performance Prediction of Centrifugal Pumps and Compressors", 25th Annual Gas Turbine conference and 22nd annual Fluids Engineering Conference Proceedings ASME 1980

References

25-6

Revision D

87. Childs, T.H.C., Dalgarno, K.W., Day, A.J. and Moore, R.B., "Automotive Timing Belt Life and a User Design Guide", Proceedings of the Institute of Mechanical Engineers, 1998 88. Reliability Analysis Center, "Nonelectronic Parts Reliability Data", NPRD-95 89. SINTEF Industrial Management, "OREDA Offshore Reliability Data", 4th Edition, 2002 90. The Complete Guide to Chains, Tsubakimoto Chain Company, 1995 91. Renold Transmission Chain Selection Procedure 92. PST =>Solutions! ,Volume 3, October 1996 93. Mechanical Engineers Handbook, Myer Kutz, et al, John Wiley & Sons, 1986 94. Mechanical Designers' Workbook, "Fastening, Joining & Connecting", J. Shigley and C. Mischke, McGraw-Hill 1986 95. Mechanical Designers' Workbook, "Mechanisms", J. Shigley and C. Mischke, McGraw-Hill 1986 96. Mechanical Designers' Workbook, "Power Transmission Elements", J. Shigley and C. Mischke, McGraw-Hill 1986 97. " The Chemical Engineering Guide to Compressors", Richard Greene, McGraw Hill Publications Company, 1984 98. Raymond J. Drago, "Rating the Load Capacity of Involute Splines", Machine Design, February 12, 1976 99. David L. McCarthy, "A Better Way to Rate Gears", Machine Design, March 7, 1996 100. Fittings and Flanges, Hydraulics & Pneumatics Magazine, 101. John H. Bickford, "An Introduction to the Design and Behavior of Bolted Joints", Marcel Dekker, Inc., 1990 102. Dan Seger, Niagara Gear Corporation, "Inside Splines" , Gear Solutions, January 2005 103. Mechanical Designers' Workbook, "Gearing", J. Shigley and C. Mischke, McGraw-Hill 1986

References

25-7

Revision D

104. Raymond J. Drago, "Fundamentals of Gear Design", Butterworth Publishers, 1988 105. OREDA Offshore Reliability Data, 5th Edition Det Norske Veritas, N-1363 Hovik, Norway 2009 ISBN 978-82-14-04830-8 106. Design and Analysis of Machine Elements, Douglas Wright, Department of Mechanical and Materials Engineering, The University of Western Australia 107. Salzman, R.H. and Reaburn, S. M. `Probabilistic Modeling for Timing Belt Fatigue Life Predictions Using Accelerated Testing' Int. J. of Materials & Product Technology, 2001 108. Daryl Beatty, Dow Chemical Company, "Oil analysis Boosts Compressor Reliability". Practicing Oil Analysis Magazine, November 2004 109. Robert Moffatt, Gast Manufacturing Corp., "Prolonging Compressor Life", Machine Design, May 11, 1978 110. John L. Wright, "Chains for Drives and Conveyors ­ Lube `Em to Last", Machinery Lubrication Magazine, March 2002 111. Johnson Electric, Solenoid Technical Data, May 2008 112. NSK Product Guide ­ Bearings 2008, NSK Americas, Inc. 113. Meine van der Meulen, "On the Use of Smart Sensors, Common Cause Failure and the Need for Diversity", Center for Software Reliability, City University, London, 2008 114. Zhanyang Zhang and Miriam R. Tausner, "Using Markov Process to Model Wireless Sensor Network Life Expectancy with QoS Constraints, Department of Computer Science, College of Staten Island/City University of New York, 2008 115. Partab Jeswani and John Bleda, "A Predictive Process for Spring Failure Rates in Automotive Parts Application", General Motors Corporation, SAE Technical Paper 910356, February 1991 116. Dr. Gerhard G. Antony, "How to Determine the MTBF of Gearboxes", Power Transmission Engineering, April 2008

References

25-8

Revision D

117. Jerry L. Lyons, Lyons' Valve Designer's Handbook, Van Nostrand Reinhold Company, 1982 118. MIL-STD-1629, "Procedures for Performing a Failure Mode, Effects and Criticality Analysis", August 1998 119. Jack A. Collins, Henry Busby and George Stabb, Mechanical Design of Machine Elements and Machines, the Ohio State University, John Wiley & Sons, 2010 120. Tyler G. Hicks, Handbook of Mechanical Engineering Calculations, McGraw-Hill, 2006 121. Bearing Failure Modes, NAEC-92-153, Naval Air Engineering Center, Lakehurst, NJ 1983 122. "How dirt and Water Slash Bearing Life", Richard C. Beercheck, Machine Design, July 6, 1978 123. Centrifugal Pump & Mechanical Seal Manual, William J. McNally, 2009 124. Parker O-Ring Handbook, 2001 Edition, Catalog ORD 5700/US, Parker Hannifin Corporation 125. "Improving the Reliability of Mechanical Seals", Michael Huebner, Chemical Engineering Progress, November 2005 126. Maintenance and Application Guide for Control Relays and Timers, Electric Power Research Institute, EPRI TR 102067s, December 1993 127. Explaining Motor Failure, Austin Bonnett and Chuck Young EASA, EC&M Magazine, October 1, 2004 128. "Rotary Screw or Reciprocating Air Compressor: Which One is Right?", Bryan Fasano and Randy Davis, Gardner Denver, Plant Engineering, September 1998 129. "Run Times", August 2005, Dale B. Andrews, Lawrence Pumps, Inc. 130. "A Practical Guide to Compressor Technology", Second Edition, Heinz P. Bloch, John Wiley & Sons, 2006

References

25-9

Revision D

131. "Tidal Current Turbine Reliability: Power Take-off Train Models and Evaluation, C. Iliev and D. Val, Third International Conference on Ocean Energy, October 2010 132. "Temperature Monitoring Is Key to Motor Reliability", Thomas H. Bishop, Electrical Apparatus Service Association, Maintenance Technology Magazine, July 2004 133. "Performance Prediction of Centrifugal Pumps and Compressors", 25th Annual Gas Turbine conference and 22nd annual Fluids Engineering Conference Proceedings ASME 1980 134. " The Chemical Engineering Guide to Compressors", Richard Greene, McGraw Hill Publications Company, 1984 135. Handbook of Spring Design, Spring Manufacturers Institute, Inc. 2002

References

25-10

Revision D

Information

CHAPTER 25 Rev D NSWC-2011

10 pages

Find more like this

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

155570


You might also be interested in

BETA
Microsoft Word - Lackey135.doc
LCMfg Design Guide final_Rev A3_nc2.doc
Microsoft Word - Letters1