Read NEPChateaugayApp-SecIX-MaterialSafetyDataTOCandSheets-Q.pdf text version

Material Safety Data Sheet Table of Contents

1. Product Name: Rust Veto 342 Product Type: TBD Supplier: Houghton International Inc. 2. Product Name: C5-A Copper Based Anti-Seize Aerosol Product Type: Lubricant Supplier: Loctite Corporation 3. Product Name: HEMPEL Urethane Product Type: 5595D White 10000 Supplier: HEMPEL Coatings (USA), Inc. 4. Product Name: 640 High Strength Sleeve Retainer Product Type: Anaerobic Supplier: Loctite Corporation 5. Product Name: Hemucryl Product Type: 48130 Grey 11150 Supplier: HEMPEL Coatings (USA), Inc. 6. Product Name: Optimol Optipit Product Type: TBD Supplier: Castrol Australia Pty. 7. Product Name: Molybdenum disulfide grease Product Type: Grease Supplier: Dow Corning Corporation 8. Product Name: Loctite ® 609 Retaining Compound Fast Curing Product Type: Anaerobic Adhesive Supplier: Henkel Loctite Corporation 9. Product Name: Heavy Duty-Anti Seize Product Type: Lubricant Supplier: Henkel Loctite Corporation 10. Product Name: Gleitmo 585 K Product Type: Lubricating Grease Supplier: Fuchs Lubritech GmbH 11. Product Name: SikaFlex 221 Product Type: Pur Sealant Supplier: Sika Corporation

Material Safety Data Sheet Table of Contents (cont).

12. Product Name: HEMPEL's Curing Agent 927US Product Type: Paint Supplier: HEMPEL Coating (USA). Inc. 13. Product Name: Silicone Industrial Sealant Product Type: Silicone Rubber Supplier: GE Silicones 14. Product Name: Optigear Synthetic A 320 Product Type: Lubricant Supplier: Castrol Industrial North America Inc. 15. Product Name: Loctite ® 243 Threadlocker Medium Strength Product Type: Anaerobic Sealant Supplier: Henkel Corporation 16. Product Name: A-Component for Two-Component Polyurethane Foam System Product Type: Urethane Foam Supplier: FOMO Products Inc. 17. Product Name: B-Component for Two-Component Polyurethane Foam System Product Type: Urethane Foam Supplier: FOMO Products, Inc.

LOCTITE CORPORATION 03/17/02 MATERIAL SAFETY DATA SHEET of 06 1. PRODUCT AND COMPANY IDENTIFICATION Product name: Item number: Product Type: Company Address: Medical Emergency Number: Fax: C5-A Copper Based Anti-Seize Aerosol 51003 Lubricant Loctite Corporation 1001 Trout Brook Crossing Rocky Hill, Connecticut. 06067 (860) 571-5100 (860) 571-5465 Page 01

2. COMPOSITION/INFORMATION ON INGREDIENTS Ingredient CAS Number % 1-5 Exposure Limits TWA: 5 STEL: 10 mg/m3 TWA: 5 mg/m3 1-5 1-5 1-5 OSHA

Distillates (petroleum), 64742-54-7 ACGIH hydrotreated heavy paraffinic Petroleum lubricating oil 64742-65-0 ACGIH Residual oils 64742-57-0 ACGIH (petroleum), hydrotreated Residual oils 64742-62-7 ACGIH (petroleum), solvent-de-waxed Mineral oil 64742-52-5 ACGIH Calcium hydroxide respirable Graphite respirable Silica, quartz 14808-60-7 7782-42-5 1305-62-0

TWA: 5 STEL: 10 mg/m3 TWA: 5 mg/m3 OSHA TWA: 5 STEL: 10 mg/m3 TWA: 5 mg/m3 OSHA TWA: 5 STEL: 10 mg/m3 TWA: 5 mg/m3 OSHA

5-10 1-5

TWA: 5 STEL: 10 mg/m3 TWA: 5 mg/m3 TWA: 5 mg/m3 TWA: 5 mg/m3 OSHA ACGIH OSHA

1-5

TWA: 15 mg/m3 OSHA total TWA: 2 mg/m3 ACGIH respirable TWA: 5 mg/m3 OSHA TWA: 15 mg/m3 OSHA total TWA: 0.05 mg/m3 ACGIH respirable TWA: 10 mg/m3 OSHA respirable TWA: 1 mg/m3 ACGIH TWA: 1 mg/m3 OSHA TWA: 0.1 mg/m3 OSHA TWA: 50 ppm ACGIH SKIN

1-5

Copper n-Hexane

7440-50-8 110-54-3

5-10 10-20

Isobutane n-Heptane ACGIH Propane

75-28-5 142-82-5

10-20 10-20

TWA: 500 ppm OSHA TWA: 1800 mg/m3 OSHA Not established. TWA: 1640 STEL: 2050 mg/m3 ACGIH TWA: 400 STEL: 500 ppm TWA: TWA: TWA: TWA: TWA: 500 ppm OSHA 2000 mg/m3 OSHA 2500 ppm ACGIH 1000 ppm OSHA 1800 mg/m3 OSHA

74-98-6

5-10

LOCTITE CORPORATION 03/17/02 MATERIAL SAFETY DATA SHEET of 06 Product Name: Item No.: 3. HAZARDS IDENTIFICATION ****EMERGENCY OVERVIEW**** PHYSICAL STATE:Aerosol COLOR:Gray ODOR: Solvent. DANGER! EXTREMELY FLAMMABLE. CAUSES SEVERE EYE AND SKIN IRRITATION. HARMFUL IF INHALED OR SWALLOWED. C5-A Copper Based Anti-Seize A 51003 Page 02

Potential Health Effects Eye: Severe eye irritation. discomfort. Skin: Severe skin irritation. Ingestion: Harmful if swallowed. Prolonged contact may cause burns Moderately toxic by ingestion Blurred vision. Excess tearing. Pain and

Inhalation: Harmful if inhaled. Liquid aspirated into the lungs may cause serious injury or death. Causes respiratory tract irritation. Conditions Aggravated by Exposure: Skin disorders. Eye disorders. Chronic: Detailed information provided in section 11. 4. FIRST AID MEASURES Eye: Immediately flush eyes with plenty of water for at least 15 minutes.

Get medical attention. Skin: Immediately flush skin with plenty of water (using soap, if available) for at least 15 minutes. Wash clothing before reuse. Get medical attention. Ingestion: Keep individual calm. DO NOT induce vomiting. Get medical attention. Inhalation: Remove to fresh air. If symptoms develop and persist, get medical attention. Note to Physician: None. LOCTITE CORPORATION 03/17/02 MATERIAL SAFETY DATA SHEET of 06 Product Name: Item No.: 5. FIRE FIGHTING MEASURES Flash Point: CLOSED CUP : <0.F (<-18.C). Setaflash. Extinguishing Media: Dry chemical, CO2, alcohol foam or water fog Flammable Limits: LOWER: 1% UPPER: 9.5% Special Fire Fighting Procedures: Hazardous Combustion Products: Oxides of carbon. Unusual Fire or Explosion Hazards: None. 6. ACCIDENTAL RELEASE MEASURES In Case of Spill or Leak: Immediately contact emergency personnel. Eliminate all ignition sources. Keep unnecessary personnel away. 7. HANDLING AND STORAGE Handling: Do not puncture or incinerate container. Keep away from heat, sparks and flame. Use only with adequate ventilation. Storage: Keep in a cool and well-ventilated area. C5-A Copper Based Anti-Seize A 51003 Page 03 Remove contaminated clothing and shoes.

For information on product shelf life, contact Loctite Customer Service at 1(800)243-4874 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Engineering Controls: Use local exhaust ventilation if the potential for airborne exposure exists. Eye/Face Protection: Chemical splash goggles or safety glasses with side shields. Full face shield should be used if the potential exists for splashing or spraying of product. Skin Protection: Use chemical resistant, impermeable clothing including gloves and either an apron or body suit to prevent skin contact. Respiratory Protection: Use a NIOSH approved air-purifying respirator with an organic vapor cartridge. Use a full face supplied air respirator if airborne concentrations exceed established exposure limits. See Section 2 COMPOSITION/INFORMATION ON INGREDIENTS for exposure limits LOCTITE CORPORATION 03/17/02 MATERIAL SAFETY DATA SHEET of 06 Product Name: Item No.: C5-A Copper Based Anti-Seize A 51003 Page 04

9. PHYSICAL AND CHEMICAL PROPERTIES Color: Material State: Odor: Boiling point: pH: Solubility in Water: Specific gravity: VOC: Vapor Pressure: Vapor density: Evaporation Rate: Gray Aerosol Solvent. Not applicable. Not applicable. Insoluble 1.14 447g/l Not available. >1 (Air = 1) >1 compared to Butyl acetate.

10. STABILITY AND REACTIVITY Stability: Stable. Conditions to Avoid: None known Incompatibility: Hazardous Polymerization: Will not occur.

Hazardous Decomposition Products: Oxides of carbon. 11. TOXICOLOGY INFORMATION Product Toxicology Data: Not available. Ingredient Distillates (petroleum), hydrotreated heavy paraffinic Petroleum lubricating oil Residual oils (petroleum), hydrotreated Residual oils (petroleum), solvent-de-waxed Mineral oil Calcium hydroxide Graphite Silica, quartz Copper n-Hexane Isobutane n-Heptane Propane LOCTITE CORPORATION 03/17/02 MATERIAL SAFETY DATA SHEET of 06 Product Name: Item No.: C5-A Copper Based Anti-Seize A 51003 Page 05 No No No No No No No 1 No No No No No NTP Carcinogen IARC No No No No No No No 1 No No No No No OSHA No No No No No No No + No No No No No

Key to abbreviations: NTP 1 - Known carcinogen. IARC 1 - Carcinogenic to human. OSHA + Proven. Ingredient Distillates (petroleum), hydrotreated heavy paraffinic Petroleum lubricating oil Residual oils (petroleum), hydrotreated Residual oils (petroleum), solvent-de-waxed Mineral oil Calcium hydroxide Graphite Silica, quartz evidence Copper Health Effects/Target organs No target organs. No target organs. No target organs. No target organs. Irritant. Irritant. Corrosive. Lung. Lung. Immune system.

Some

of carcinogenicity. Allergen. Blood. Central nervous system. Developmental. Gastrointestinal. Immune system.

Irritant. Mutagen. n-Hexane Isobutane n-Heptane Propane 12. ECOLOGICAL INFORMATION Ecological Information: None known 13. DISPOSAL CONSIDERATIONS

Kidney.

Liver.

Sensory. Skin. Developmental. Irritant. Nervous system. Reproductive. Lung. Cardiac. Central nervous system. Lung. Central nervous system. Irritant. Cardiac. Central nervous system. Irritant.

Recommended Method of Disposal: Dispose according to EPA and local governmental regulations. EPA Hazardous Waste Number: D001: Ignitable Waste 14. TRANSPORTATION INFORMATION Domestic Transportation (D.O.T. 49 CFR)-GROUND Shipping Description: Shipping name: Consumer Commodity Class/Division: (ORM-D) IDENTIFICATION Number: UN1950 Packing group: Not applicable. Exceptions: None. LOCTITE CORPORATION 03/17/02 MATERIAL SAFETY DATA SHEET of 06 Product Name: Item No.: C5-A Copper Based Anti-Seize A 51003 Page 06

International Air Transportation (ICAO/IATA)Shipping description: Shipping name: Aerosols, Flammable Class/Division: 2.1 Identification Number: Un1950 Packing group: Not applicable. Exceptions: None. Marine pollutant: None known 15. REGULATORY INFORMATION

SARA Title III Section 313 Chemicals: Copper, n-Hexane SARA Title III Section 311/312: None. Toxic Substances Control Act: All components are listed on or are exempt from listing on the Toxic Substances Control Act Inventory. TSCA Section 12(b) annual: None. TSCA Section 12(b) one time: None. Canadian Inventory Status: All components are listed on or are exempt from listing on the Canadian Domestic Substances List. California Proposition 65: No California Proposition 65 chemicals are known to be present. 16. OTHER INFORMATION NFPA Code: Health: Flammability: Reactivity: Special: HMIS Code: Health: Flammability: Reactivity: Protective Equipment: Prepared by: America 2 * 4 0 See Section 8. Safety, Health and Regulatory Affairs - North 2 4 0 None

application assistance . browse catalog . troubleshooting . equipment datasheets . distributor locator .what's new . career opportunities about loctite . contact loctite . literature . loctite world wide . search . home

copyright © 1997-2000 Loctite

Material Safety Data Sheet

Protective Clothing HCS DOT

Class: Flammable liquid having a flash point lower than 37.8°C (100°F).

Section I. Product Identification and Uses

Common/Trade name

HEMPEL'S URETHANE 5595D White 10000

Not applicable. Not applicable.

TSCA

Unless otherwise noted, all ingredients are TSCA listed.

Chemical name Chemical formula Chemical family Material uses

CAS# Code

Mixture. 5595D10000US001 Not applicable.

HEMPEL Coatings (USA), Inc. 600 Conroe Park North Drive Conroe, Texas 77303

Two component product - base component (Paint.)

Molecular weight Coatings: Paint. Protective coating for metal products. Use in metals industry, metal product Manufacturer fabrication, ship bulding & repair, offshore oil & gas platforms, chemical processing industries, refineries, etc.

Mixing Ratio Supplier

Mix base with cure by volume 4:1. Use with cure Hempel's 931US Manufacturer Telephone: HEMPEL Coatings (USA), Inc.

600 Conroe Park North Drive Conroe, Texas 77303

Toll free, if outside area codes 713,281,409,or 936: (800) 678-6641 Regular phone number: (936) 523-6000

Section IA. First Aid Measures

Eye contact Skin contact

Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Cold water may be used. WARM water MUST be used. Get medical attention if irritation occurs. Wash with soap and water. Cover the irritated skin with an emollient. Get medical attention if irritation develops.

Hazardous skin contact Not available. Slight inhalation Hazardous inhalation

If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention if symptoms appear. Evacuate the victim to a safe area as soon as possible. Loosen tight clothing such as a collar, tie, belt or waistband. If breathing is difficult, administer oxygen. If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek medical attention. Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention if symptoms appear. Not available.

Slight ingestion

Hazardous ingestion

Section II. Hazardous Ingredients

Name CAS # % by Weight TLV/PEL LC50/LD50

1) n-butylacetate

123-86-4

5-15

2) Acetate ester, branched 3) titanium dioxide

90438-79-2 13463-67-7

0-5 15-30

Continued on Next Page

TWA: 710 (mg/m3) from OSHA (PEL) [United States] TWA: 150 STEL: 200 (ppm) from ACGIH (TLV) [United States] TWA: 713 STEL: 950 (ppm) from ACGIH (TLV) [United States] Not available. TWA: 15 (mg/m3) from OSHA (PEL) [United States] TWA: 10 (ppm) from ACGIH

ORAL (LD50): Acute: 14130 mg/kg [Rat]. 7100 mg/kg [Mouse].

Not available. Not available.

5595D10000US001

TWA: 10 (ppm) from ACGIH (TLV) [United States] 4) talc 14807-96-6 5-15 TWA: 2 (mg/m3) from OSHA (PEL) [United States] Inhalation Respirable. TWA: 2 (ppm) from ACGIH (TLV) [United States] Inhalation Respirable. TWA: 0.1 (mg/m3) from OSHA (PEL) [United States] Inhalation Respirable. TWA: 0.1 (ppm) from ACGIH (TLV) [United States] Inhalation Respirable. Not available. Not available.

Page Number: 2

Not available.

5) quartz, chrystalline, respirable

14808-60-7

0-5

Not available.

6) Hydrocarbons C8-C11 7) Acetate ester

68553-14-0 88230-35-7

0-5 5-15

Not available. Not available.

Section III. Physical Data

Physical state and appearance pH (1% soln/water) Odor threshold Volatility Melting point Boiling point Specific gravity Vapor density Vapor pressure Evaporation rate VOC Viscosity LogKow Ionicity (surface active agent) Instability temperature Conditions of instability Dispersion properties Solubility

Liquid. Neutral.

Odor Taste

Not available. Not available. White.

The highest known value is 0.31 ppm Color (n-butylacetate) 36.7% (v/v). 23.4% (w/w). Not available.

The lowest known value is 126.3°C (259.3°F) (n-butylacetate). Weighted average: 141.44°C (286.6°F) 1.35 (Water = 1) >1 (Air = 1) The highest known value is 0.2 kPa (@ 20°C) (Acetate ester). Weighted average: 0.17 kPa (@ 20°C) <1 compared to Ether (anhydrous). 316 (g/l). Not available. The product is more soluble in oil. Not available. Not available. Not available. Is not dispersed in cold water, hot water. See solubility in methanol, diethyl ether, n-octanol, acetone. Partially soluble in methanol, diethyl ether, n-octanol, acetone. Very slightly soluble in cold water, hot water.

Section IV. Fire and Explosion Data

The product is:

Flammable.

Auto-ignition temperature The lowest known value is 293.89°C (561°F) (Acetate ester, branched). Fire degradation products These products are carbon oxides (CO, CO2). Some metallic oxides. Flash points Flammable limits

CLOSED CUP: Between 23°C (73°F) and 37.8°C (100°F). LOWER: 1% UPPER: Less or equal to 13%

Continued on Next Page

5595D10000US001

Fire extinguishing procedures

Page Number: 3

Flammable liquid, soluble or dispersed in water. SMALL FIRE: Use DRY chemical powder. LARGE FIRE: Use alcohol foam, water spray or fog. Cool containing vessels with water jet in order to prevent pressure build-up, autoignition or explosion. Highly flammable in presence of open flames and sparks. Flammable in presence of oxidizing materials. Slightly flammable to flammable in presence of heat. Non-flammable in presence of shocks, of reducing materials, of combustible materials, of organic materials, of metals, of acids, of alkalis, of moisture.

Remark Not available.

Flammability

Risks of explosion

Risks of explosion of the product in presence of mechanical impact: Not available. Risks of explosion of the product in presence of static discharge: Not available.

Remark Not available.

Section V. Reactivity Data

Stability Hazardous decomp. products Degradability Products of degradation

The product is stable. Not available. Not available. These products are carbon oxides (CO, CO2) and water. Some metallic oxides. The products of degradation are more toxic than the product itself.

Remark Not available.

Corrosivity

Not considered to be corrosive for metals and glass.

Remark Not available.

Reactivity

Reactive with oxidizing agents, acids. Slightly reactive to reactive with alkalis.

Remark Not available.

Section VI. Toxicological Properties

Routes of entry TLV

Absorbed through skin. Eye contact. Inhalation.

n-butylacetate TWA: 710 (mg/m3) from OSHA (PEL) [United States] TWA: 150 STEL: 200 (ppm) from ACGIH (TLV) [United States] TWA: 713 STEL: 950 (ppm) from ACGIH (TLV) [United States] TWA: 713 STEL: 950 (mg/m3) from RQMT Acetate ester, branched TWA: 50 (ppm) from Exxon limit --- consider same as heptyl acetate Inhalation Total. titanium dioxide TWA: 15 (mg/m3) from OSHA (PEL) [United States] TWA: 10 (ppm) from ACGIH (TLV) [United States] TWA: 10 (mg/m3) from RQMT talc TWA: 2 (mg/m3) from OSHA (PEL) [United States] Inhalation Respirable. TWA: 2 (ppm) from ACGIH (TLV) [United States] Inhalation Respirable. TWA: 2 STEL: 3 (mg/m3) from RQMT Inhalation Respirable. quartz, chrystalline, respirable TWA: 0.1 (mg/m3) from OSHA (PEL) [United States] Inhalation Respirable. TWA: 0.1 (ppm) from ACGIH (TLV) [United States] Inhalation Respirable. TWA: 0.1 (mg/m3) from RQMT Inhalation Respirable.

Continued on Next Page

5595D10000US001

1,2,4-trimethylbenzene TWA: 25 (ppm) from ACGIH (TLV) [United States] STEL: 150 (ppm) from ACGIH (TLV) [United States] CEIL: 200 (ppm) from NIOSH [United States] TWA: 100 (ppm) from NIOSH [United States] 1,2,3-trimethylbenzene TWA: 25 (ppm) from ACGIH (TLV) [United States] STEL: 150 (ppm) from ACGIH (TLV) [United States] CEIL: 200 (ppm) from NIOSH [United States] TWA: 100 (ppm) from NIOSH [United States] xylene TWA: 100 (ppm) from OSHA (PEL) [United States] TWA: 100 STEL: 150 (ppm) from ACGIH (TLV) [United States] TWA: 434 STEL: 651 (ppm) from ACGIH (TLV) [United States] TWA: 0.2 (ppm) from WHO - Recomended Guidance Value [United Nations]

Page Number: 4

Consult local authorities for acceptable exposure limits.

Toxicity to animals

Acute oral toxicity (LD50): 7100 mg/kg [Mouse]. (n-butylacetate).

Remark Not available.

Chronic effects on humans

Slightly hazardous in case of inhalation (lung irritant). CARCINOGENIC EFFECTS: Classified A4 (Not classifiable for human or animal.) by ACGIH [n-butylacetate]. Classified A4 (Not classifiable for human or animal.) by ACGIH, 3 (Not classifiable for human.) by IARC [titanium dioxide]. Classified A4 (Not classifiable for human or animal.) by ACGIH, 3 (Not classifiable for human.) by IARC [talc]. Classified 1 (Proven for human.) by IARC, + (Proven.) by OSHA, + (Proven.) by NIOSH [quartz, chrystalline, respirable]. Classified 2 (Some evidence.) by NTP [quartz, chrystalline, respirable]. Classified A4 (Not classifiable for human or animal.) by ACGIH, 3 (Not classifiable for human.) by IARC [xylene]. Classified 3 (Not classifiable for human.) by IARC [2-ethyl toluene]. MUTAGENIC EFFECTS: Not available. TERATOGENIC EFFECTS: Not available. DEVELOPMENTAL TOXICITY: Not available. The substance is toxic to blood, kidneys, lungs, the nervous system, liver, upper respiratory tract, skin, eyes. Repeated or prolonged exposure to the substance can produce target organs damage.

Remark NIOSH- titanium dioxide -a potential carcinogen to lungs in rats due to inhalation of excessive dust and overwhelmed lung clearance mechanisms. The National Cancer Institute bioassay concluded that titanium dioxide did not effect mortaility, and was not carcinogenic at dose levels of 25,000 or 50,000 ppm in rats or mice. (Referenced in Federal Register: March 25,1998. Vol 63; No. 571, Page 14361). (titanium dioxide)

Acute effects on humans Slightly hazardous in case of skin contact (irritant), of eye contact (irritant), of inhalation. Remark NIOSH- titanium dioxide -a potential carcinogen to lungs in rats due to inhalation of excessive dust and overwhelmed lung clearance mechanisms. The National Cancer Institute bioassay concluded that titanium dioxide did not effect mortaility, and was not carcinogenic at dose levels of 25,000 or 50,000 ppm in rats or mice. (Referenced in Federal Register: March 25,1998. Vol 63; No. 571, Page 14361). (titanium dioxide)

Section VII. Preventive Measures

Waste information Waste stream Storage Precautions

Waste must be disposed of in accordance with federal, state and local environmental control regulations. Not available. Store in a segregated and approved area. Keep container in a cool, well-ventilated area. Keep container tightly closed and sealed until ready for use. Avoid all possible sources of ignition (spark or flame). Keep locked up. Keep away from heat. Keep away from sources of ignition. Ground all equipment containing material. Do not ingest. Do not breathe gas/fumes/ vapor/spray. Wear suitable protective clothing. If ingested, seek medical advice immediately and show the container or the label. Keep away from incompatibles such as oxidizing agents, acids. Absorb with an inert material and put the spilled material in an appropriate waste disposal.

Small spill and leak

Continued on Next Page

5595D10000US001

Large spill and leak

Page Number: 5

Flammable liquid. Keep away from heat. Keep away from sources of ignition. Stop leak if without risk. Absorb with DRY earth, sand or other non-combustible material. Do not touch spilled material. Prevent entry into sewers, basements or confined areas; dike if needed. Be careful that the product is not present at a concentration level above TLV. Check TLV on the MSDS and with local authorities. Splash goggles. Full suit. Vapor respirator. Boots. Gloves. A self-contained breathing apparatus should be used to avoid inhalation of the product. Suggested protective clothing might not be sufficient; consult a specialist BEFORE handling this product.

Protective clothing in case of large spill

Section VIII. Classification

DOT

Class 3: Flammable liquid.

Shipping name: Paint UNNA: UN 1263 PG: III

Maritime transportation

Not pollutant.

Remark Not available. HCS

Class: Flammable liquid having a flash point lower than 37.8°C (100°F).

Remark

Not available.

Federal and State Regulations

California prop. 65: This product contains the following ingredients for which the State of California has found to cause cancer, birth defects or other reproductive harm, which would require a warning under the statute: 2-ethyl toluene California prop. 65: This product contains the following ingredients for which the State of California has found to cause birth defects which would require a warning under the statute: 2-ethyl toluene Connecticut hazardous material survey.: xylene Illinois toxic substances disclosure to employee act: xylene Illinois chemical safety act: xylene New York release reporting list: xylene Rhode Island RTK hazardous substances: xylene Pennsylvania RTK: n-butylacetate; titanium dioxide; talc; quartz, chrystalline, respirable; di-isobutylketone; 1,2,4-trimethylbenzene; 1,2,3-trimethylbenzene; xylene; 2-ethyl toluene; ethylbenzene; cumene Florida: n-butylacetate; talc; quartz, chrystalline, respirable; di-isobutylketone; xylene; 2-ethyl toluene; ethylbenzene; cumene Minnesota: n-butylacetate; titanium dioxide; talc; quartz, chrystalline, respirable; di-isobutylketone; xylene; 2-ethyl toluene; ethylbenzene; cumene Michigan critical material: xylene; 2-ethyl toluene Massachusetts RTK: n-butylacetate; titanium dioxide; talc; quartz, chrystalline, respirable; di-isobutylketone; 1,2,4-trimethylbenzene; 1,2,3-trimethylbenzene; xylene; 2-ethyl toluene; ethylbenzene; cumene New Jersey: n-butylacetate; di-isobutylketone; xylene; 2-ethyl toluene; ethylbenzene; cumene New Jersey spill list: xylene New Jersey toxic catastrophe prevention act: xylene Louisiana RTK reporting list: xylene Louisiana spill reporting: xylene

Continued on Next Page

5595D10000US001

Page Number: 6

TSCA 5(e) substance consent order: n-butylacetate TSCA 8(a) PAIR: dibutyltin dilaurate; poly(dimethylsiloxane); 1,2,4-trimethylbenzene; 1,2,3-trimethylbenzene; xylene; 2-ethyl toluene; ethylbenzene; cumene TSCA 8(a) IUR: n-butylacetate; cumene TSCA 8(b) inventory: unless otherwise noted, all ingredients are TSCA listed. SARA 302/304/311/312 hazardous chemicals: xylene SARA 311/312 MSDS distribution - chemical inventory - hazard identification: di-isobutylketone: fire, immediate health hazard; xylene: fire; 2-ethyl toluene: fire, immediate health hazard, delayed health hazard; ethylbenzene: fire, immediate health hazard CERCLA: Hazardous substances.: n-butylacetate: 5000 lbs. (2268 kg); xylene: 100 lbs. (45.36 kg); 2-ethyl toluene: 1000 lbs. (453.6 kg); ethylbenzene: 1000 lbs. (453.6 kg); cumene: 5000 lbs. (2268 kg);

Section IX. Protective Clothing

Safety glasses. Lab coat. Vapor respirator. Be sure to use an approved/certified respirator or equivalent. Gloves (impervious).

Section X. Other Information

References

Not available.

Note: Consult Code of Federal Regulations, Title 29, Labor, Parts 1910 and 1915 concerning occupational safety and health standards and regulations, as well as any other applicable Federal, State and Local regulation on safe practices in coating operations.

Validated by Algimantas Pliodzinskas on 10/4/2000. Verified by Algimantas Pliodzinskas. Printed 10/4/2000. Emergency telephone number For Transportation Emergencies, call CHEMTREC: (800) 424-9300. If outside USA/Canada, call: (703) 527-3887. For all other information call Hempel Coatings (USA), Inc. (936) 523-6000. Toll free [ if outside area codes 713, 281,409,936]: (800) 678-6641

To the best of our knowledge, the information contained herein is accurate. However, neither the above named supplier nor any of its subsidiaries assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.

Material Safety Data Sheet

Revision Date: 03/31/2004 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product name: Loctite(R) 609 Retaining Compound Fast Curing Product type: Anaerobic Adhesive Company address: Henkel Corporation 1001 Trout Brook Crossing Rocky Hill, Connecticut 06067 Item number: 60943 Region: United States Contact Information: Telephone: 860.571.5100 Emergency telephone: 860.571.5100 Internet: www.loctite.com

Issue date: 03/31/2004

2. COMPOSITION/INFORMATION ON INGREDIENTS

Hazardous components Polyglycol dimethacrylate 25852-47-5 Hydroxyalkyl methacrylate 868-77-9 Coumarone-indene resin 68132-02-5 Poly (ethyl methacrylate) 9003-42-3 Cumene hydroperoxide 80-15-9 Saccharin 81-07-2

% 60-100

ACGIH TLV None

OSHA PEL None

OTHER None

10-30

None

None

3 ppm (ceiling)

5-10

None

None

None

1-5

None

None

None 1 ppm (6 mg/m3) Skin (WEEL)

1-5

None

None

1-5

None

None

None

3. HAZARDS IDENTIFICATION EMERGENCY OVERVIEW

HMIS: Physical state: Color: Odor: Liquid Green Mild HEALTH: FLAMMABILITY: PHYSICAL HAZARD: Personal Protection: 2* 1 1 See Section 8

WARNING:

CAUSES EYE AND SKIN IRRITATION. MAY CAUSE ALLERGIC SKIN REACTION. MAY CAUSE RESPIRATORY TRACT IRRITATION. MAY BE HARMFUL IF SWALLOWED.

Skin, Inhalation, Eyes

Relevant routes of exposure: Potential Health Effects Inhalation: Skin contact: Eye contact: Ingestion: Item number: 60943

May cause respiratory tract irritation. Moderate skin irritation. May cause allergic skin reaction. Contact with eyes will cause irritation. May be harmful if swallowed. Product name: Loctite(R) 609 Retaining Compound Fast Curing 1 of 5

Existing conditions aggravated by exposure:

Eye, skin, and respiratory disorders.

See Section 11 for additional toxicological information.

4. FIRST AID MEASURES

Inhalation: Skin contact:

Remove to fresh air. If symptoms develop and persist, get medical attention. Wash with soap and water. Remove contaminated clothing and shoes. Wash clothing before reuse. Get medical attention if symptoms occur. Flush with copious amounts of water, preferably, lukewarm water for at least 15 minutes, holding eyelids open all the time. Get medical attention. Do not induce vomiting. Keep individual calm. Obtain medical attention.

Eye contact:

Ingestion:

5. FIRE-FIGHTING MEASURES

Flash point: Autoignition temperature: Flammable/Explosive limits-lower %: Flammable/Explosive limits-upper %: Extinguishing media: Special fire fighting procedures: Unusual fire or explosion hazards: Hazardous combustion products: Greater than 93ºC (200ºF) Not available Not available Not available Foam, dry chemical or carbon dioxide. Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. None Oxides of carbon. Oxides of sulfur. Oxides of nitrogen. Irritating organic vapors. Tagliabue closed cup

6. ACCIDENTAL RELEASE MEASURES

Environmental precautions: Clean-up methods: Prevent product from entering drains or open waters. Soak up with inert absorbent. Store in a partly filled, closed container until disposal.

7. HANDLING AND STORAGE

Handling: Avoid contact with eyes, skin and clothing. Avoid breathing vapor and mist. Wash thoroughly after handling. Use only with adequate ventilation. For safe storage, store at or below 38°C (100°F). Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use. Refer to Section 10. For information on product shelf life contact Henkel Customer Service at (800) 243-4874.

Storage:

Incompatible products:

8. EXPOSURE CONTROLS / PERSONAL PROTECTION

Engineering controls: No specific ventilation requirements noted, but forced ventilation may still be required if concentrations exceed occupational exposure limts. Use NIOSH approved respirator if there is potential to exceed exposure limit(s). Product name: Loctite(R) 609 Retaining Compound Fast Curing 2 of 5

Respiratory protection: Item number: 60943

Skin protection:

Use impermeable gloves and protective clothing as necessary to prevent skin contact. Neoprene gloves. Butyl rubber gloves. Natural rubber gloves. Glove recommendations are based upon permeation study results for similar products. Safety goggles or safety glasses with side shields. See Section 2 for exposure limits.

Eye/face protection:

9. PHYSICAL AND CHEMICAL PROPERTIES

Physical state: Color: Odor: Vapor pressure: pH: Boiling point/range: Melting point/range: Specific gravity: Vapor density: Evaporation rate: Solubility in water: Partition coefficient (n-octanol/water): VOC content: Liquid Green Mild Less than 5 mm Hg at 27ºC (80ºF) Not applicable Greater than 149ºC (300ºF) Not available 1.1 Not available Not available Slight Not available 34.0%; 374 grams/liter (EPA Method 24)

10. STABILITY AND REACTIVITY

Stability: Hazardous polymerization: Hazardous decomposition products: Incompatability: Conditions to avoid: Stable. Will not occur. Oxides of carbon. Oxides of sulfur. Oxides of nitrogen. Irritating organic vapors. Strong oxidizers. See "Handling and Storage" (Section 7) and "Incompatabilty" (Section 10).

11. TOXICOLOGICAL INFORMATION

Product toxicity data: Acute oral LD50 greater than 10, 000 mg/kg (rat). Acute dermal LD50 greater than 5000 mg/kg (rabbit)(estimated). Carcinogen Status Hazardous components Polyglycol dimethacrylate Hydroxyalkyl methacrylate Coumarone-indene resin Poly (ethyl methacrylate) Cumene hydroperoxide Saccharin NTP Carcinogen No No No No No No IARC Carcinogen No No No No No No OSHA Carcinogen No No No No No No

Literature Referenced Target Organ & Other Health Effects Hazardous components Polyglycol dimethacrylate Hydroxyalkyl methacrylate Coumarone-indene resin Poly (ethyl methacrylate) Cumene hydroperoxide Saccharin Health Effects/Target Organs Allergen, Irritant Allergen, Irritant No data Irritant Allergen, Central nervous system, Corrosive, Irritant, Mutagen No Target Organs

12. ECOLOGICAL INFORMATION

Item number: 60943 3 of 5 Product name: Loctite(R) 609 Retaining Compound Fast Curing

Ecological information:

Not available

13. DISPOSAL CONSIDERATIONS

Information provided is for unused product only. Recommended method of disposal: EPA hazardous waste number: Dispose of according to Federal, State and local governmental regulations. Not a RCRA hazardous waste.

14. TRANSPORT INFORMATION

U.S. Department of Transportation Ground (49 CFR): Proper shipping name: Unrestricted Hazard class or division: None Identification number: None Packing group: None International Air Transportation (ICAO/IATA): Proper shipping name: Unrestricted Hazard class or division: None Identification number: None Packing group: None WaterTransportation (IMO/IMDG): Proper shipping name: Hazard class or division: Identification number: Packing group: Marine pollutant:

Unrestricted None None None None

15. REGULATORY INFORMATION

United States Regulatory Information TSCA 8 (b) Inventory Status: TSCA 12 (b) Export Notification: CERCLA/SARA Section 302 EHS: CERCLA/SARA Section 311/312: CERCLA/SARA 313: All components are listed or are exempt from listing on the Toxic Substances Control Act Inventory. None. None above reporting de minimus. Immediate Health Hazard, Delayed Health Hazard This product contains the following toxic chemicals subject to the reporting requirements of section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 (40 CFR 372). Cumene hydroperoxide (CAS# 80-15-9) . This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. o-Toluidine (CAS# 95-53-4). C.I. Solvent yellow 14 (CAS# 842-07-9). Ethylene oxide (CAS# 75-21-8).

California Proposition 65:

Canada Regulatory Information

CEPA DSL/NDSL Status: WHMIS hazard class:

All components are listed on or are exempt from listing on the Domestic Substances List. D.2.A, D.2.B

Item number:

60943 4 of 5

Product name: Loctite(R) 609 Retaining Compound Fast Curing

16. OTHER INFORMATION

This material safety data sheet contains changes from the previous version in sections: Expanded chemical information in Section 2 and related sections. Prepared by: Kyra Kozak Woods, Health and Regulatory Affairs Specialist

DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel Corporation does not assume responsibility for any results obtained by persons over whose methods Henkel Corporation has no control. It is the user's responsibility to determine the suitability of Henkel's products or any production methods mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and persons against any hazards that may be involved in the handling and use of any of Henkel Corporation's products. In light of the foregoing, Henkel Corporation specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular purpose, arising from sale or use of Henkel Corporation's products. Henkel Corporation further disclaims any liability for consequential or incidental damages of any kind, including lost profits.

Item number:

60943 5 of 5

Product name: Loctite(R) 609 Retaining Compound Fast Curing

DOW CORNING CORPORATION Material Safety Data Sheet

Page: 1 of 8

MOLYKOTE(R) LONGTERM 2 PLUS

1. IDENTIFICATION OF THE SUBSTANCE AND OF THE COMPANY Dow Corning Corporation South Saginaw Road Midland, Michigan 48686 24 Hour Emergency Telephone: Customer Service: Product Disposal Information: CHEMTREC: (989) 496-5900 (989) 496-6000 (989) 496-6315 (800) 424-9300

MSDS No.: 01642758 Generic Description: Physical Form: Color: Odor: Molybdenum disulfide grease Grease Black Slight odor 1 Flammability

Revision Date: 2002/01/18

NFPA Profile: Health

Note: NFPA = National Fire Protection Association

1 Instability/Reactivity

0

2. OSHA HAZARDOUS COMPONENTS CAS Number 64741-96-4 64742-65-0 64742-54-7 64741-88-4 None Wt % 30.0 - 60.0 15.0 - 40.0 15.0 - 40.0 15.0 - 40.0 7.0 - 13.0 Component Name Solvent refined heavy naphthenic distillate (petroleum) Solvent dewaxed heavy paraffinic petroleum distillate Hydrotreated heavy paraffinic petroleum distillate Solvent-refined heavy paraffinic petroleum distillate Synthetic Sperm Oil

The above components are hazardous as defined in 29 CFR 1910.1200. 3. EFFECTS OF OVEREXPOSURE Acute Effects Eye: Skin: Inhalation: Oral: Direct contact may cause mild irritation. No significant irritation expected from a single short-term exposure. Mist may irritate nose and throat. Vapor overexposure may cause drowsiness. Aspiration of liquid while vomiting may injure lungs seriously.

Prolonged/Repeated Exposure Effects Skin: Repeated or prolonged contact may cause defatting and drying of skin which may result in skin irritation and dermatitis. No known applicable information.

Inhalation:

DOW CORNING CORPORATION Material Safety Data Sheet

Page: 2 of 8

MOLYKOTE(R) LONGTERM 2 PLUS

Oral: Repeated ingestion or swallowing large amounts may injure internally.

Signs and Symptoms of Overexposure No known applicable information. Medical Conditions Aggravated by Exposure No known applicable information.

The above listed potential effects of overexposure are based on actual data, results of studies performed upon similar compositions, component data and/or expert review of the product. Please refer to Section 11 for the detailed toxicology information.

4. FIRST AID MEASURES Eye: Skin: Immediately flush with water for 15 minutes. Remove from skin and wash thoroughly with soap and water or waterless cleanser. Get medical attention if irritation or other ill effects develop or persist. Remove to fresh air. Get medical attention if ill effects persist. Get immediate medical attention. Only induce vomiting at the instructions of a physician. Never give anything by mouth to an unconscious person. Treat according to person's condition and specifics of exposure.

Inhalation: Oral:

Comments:

5. FIRE FIGHTING MEASURES Flash Point: Autoignition Temperature: Not applicable. Not determined.

Flammability Limits in Air: Not determined. Extinguishing Media: Water spray. Carbon dioxide (CO2). Dry chemical. Foam. Water can be used to cool fire exposed containers. Self-contained breathing apparatus and protective clothing should be worn in fighting large fires involving chemicals. Use water spray to keep fire exposed containers cool. Determine the need to evacuate or isolate the area according to your local emergency plan. None.

Fire Fighting Measures:

Unusual Fire Hazards:

Hazardous Decomposition Products Thermal breakdown of this product during fire or very high heat conditions may evolve the following hazardous decomposition products: Metal oxides. Sulfur oxides. Carbon oxides and traces of incompletely burned carbon compounds. Fluorine compounds. Formaldehyde.

DOW CORNING CORPORATION Material Safety Data Sheet

Page: 3 of 8

MOLYKOTE(R) LONGTERM 2 PLUS

6. ACCIDENTAL RELEASE MEASURES Containment/Clean up: Observe all personal protection equipment recommendations described in Sections 5 and 8. Wipe up or scrape up and contain for salvage or disposal. Clean area as appropriate since some silicone materials, even in small quantities, may present a slip hazard. Final cleaning may require use of steam, solvents or detergents. Dispose of saturated absorbant or cleaning materials appropriately, since spontaneous heating may occur. Local, state and federal laws and regulations may apply to releases and disposal of this material, as well as those materials and items employed in the cleanup of releases. You will need to determine which federal, state and local laws and regulations are applicable. Sections 13 and 15 of this MSDS provide information regarding certain federal and state requirements.

Note: See section 8 for Personal Protective Equipment for Spills. Call Dow Corning Corporation, (989) 496-5900, if additional information is required. 7. HANDLING AND STORAGE Use with adequate ventilation. None. Avoid eye contact. Avoid skin contact. Avoid breathing vapor, mist, dust, or fumes. Keep container closed. Do not take internally. Use reasonable care and store away from oxidizing materials. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Component Exposure Limits CAS Number 64741-88-4 Component Name Solvent-refined heavy paraffinic petroleum distillate Hydrotreated heavy paraffinic petroleum distillate Solvent dewaxed heavy paraffinic petroleum distillate Exposure Limits Observe oil mist limits. OSHA PEL (final rule) and ACGIH TLV: TWA 5 mg/m3; ACGIH STEL 10 mg/m3. Observe oil mist limits. OSHA PEL (final rule) and ACGIH TLV: TWA 5 mg/m3; ACGIH STEL 10 mg/m3. Observe oil mist limits. OSHA PEL (final rule) and ACGIH TLV: TWA 5 mg/m3; ACGIH STEL 10 mg/m3.

64742-54-7

64742-65-0

Engineering Controls Local Ventilation: General Ventilation: Recommended. Recommended.

Personal Protective Equipment for Routine Handling Eyes: Skin: Use proper protection - safety glasses as a minimum. Wash at mealtime and end of shift. Contaminated clothing and shoes should be removed as soon as practical and thoroughly cleaned before reuse. Chemical protective gloves are recommended. Nitrile Rubber. Viton(R).

Suitable Gloves:

DOW CORNING CORPORATION Material Safety Data Sheet

Page: 4 of 8

MOLYKOTE(R) LONGTERM 2 PLUS

Inhalation: Use respiratory protection unless adequate local exhaust ventilation is provided or air sampling data show exposures are within recommended exposure guidelines. Industrial Hygiene Personnel can assist in judging the adequacy of existing engineering controls. General and local exhaust ventilation is recommended to maintain vapor exposures below recommended limits. Where concentrations are above recommended limits as determined by air sampling or are unknown, appropriate respiratory protection should be worn. Follow OSHA Respirator Regulations (29 CFR 1910.134) and use NIOSH/MSHA approved respirators.

Suitable Respirator:

Personal Protective Equipment for Spills Eyes: Skin: Use full face respirator. Wash at mealtime and end of shift. Contaminated clothing and shoes should be removed as soon as practical and thoroughly cleaned before reuse. Chemical protective gloves are recommended. Respiratory protection recommended. Follow OSHA Respirator Regulations (29 CFR 1910.134) and use NIOSH/MHSA approved respirators. Protection provided by air purifying respirators against exposure to any hazardous chemical is limited. Use a positive pressure air supplied respirator if there is any potential for uncontrolled release, exposure levels are unknown, or any other circumstance where air purifying respirators may not provide adequate protection.

Inhalation/Suitable Respirator:

Precautionary Measures: Avoid eye contact. Avoid skin contact. Avoid breathing vapor, mist, dust, or fumes. Keep container closed. Do not take internally. Use reasonable care. Comments: None.

Note: These precautions are for room temperature handling. Use at elevated temperature or aerosol/spray applications may require added precautions.

9. PHYSICAL AND CHEMICAL PROPERTIES Physical Form: Color: Odor: Specific Gravity @ 25°C: Viscosity: Freezing/Melting Point: Boiling Point: Vapor Pressure @ 25°C: Vapor Density: Solubility in Water: pH: Volatile Content: Grease Black Slight odor 0.9 Not determined. Not determined. Not determined. Not determined. Not determined. Not determined. Not determined. Not determined.

Note: The above information is not intended for use in preparing product specifications. Contact Dow Corning before writing specifications.

DOW CORNING CORPORATION Material Safety Data Sheet

Page: 5 of 8

MOLYKOTE(R) LONGTERM 2 PLUS

10. STABILITY AND REACTIVITY Chemical Stability: Hazardous Polymerization: Conditions to Avoid: Materials to Avoid: Stable. Hazardous polymerization will not occur. None. Oxidizing material can cause a reaction.

11. TOXICOLOGICAL INFORMATION Component Toxicology Information No known applicable information.

Special Hazard Information on Components No known applicable information. 12. ECOLOGICAL INFORMATION Environmental Fate and Distribution Complete information is not yet available. Environmental Effects Complete information is not yet available. Fate and Effects in Waste Water Treatment Plants Complete information is not yet available. Ecotoxicity Classification Criteria High Medium <=1 >1 and <=100 <=100 >100 and <= 2000

Hazard Parameters (LC50 or EC50) Acute Aquatic Toxicity (mg/L) Acute Terrestrial Toxicity

Low >100 >2000

This table is adapted from "Environmental Toxicology and Risk Assessment", ASTM STP 1179, p.34, 1993. This table can be used to classify the ecotoxicity of this product when ecotoxicity data is listed above. Please read the other information presented in the section concerning the overall ecological safety of this material.

13. DISPOSAL CONSIDERATIONS RCRA Hazard Class (40 CFR 261) When a decision is made to discard this material, as received, is it classified as a hazardous waste? No

State or local laws may impose additional regulatory requirements regarding disposal.

DOW CORNING CORPORATION Material Safety Data Sheet

Page: 6 of 8

MOLYKOTE(R) LONGTERM 2 PLUS

Call Dow Corning Corporate Environmental Management, (989) 496-6315, if additional information is required. 14. TRANSPORT INFORMATION DOT Road Shipment Information (49 CFR 172.101) Not subject to DOT. Ocean Shipment (IMDG) Not subject to IMDG code. Air Shipment (IATA) Not subject to IATA regulations. Call Dow Corning Transportation, (989) 496-8577, if additional information is required. 15. REGULATORY INFORMATION Contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200. TSCA Status: All chemical substances in this material are included on or exempted from listing on the TSCA Inventory of Chemical Substances.

EPA SARA Title III Chemical Listings Section 302 Extremely Hazardous Substances: None. Section 304 CERCLA Hazardous Substances: Wt % Component Name CAS Number 1314-98-3 0.8 Zinc sulfide

Section 312 Hazard Class: Acute: Yes Chronic: No Fire: No Pressure: No Reactive: No Section 313 Toxic Chemicals: None present or none present in regulated quantities. Supplemental State Compliance Information California

DOW CORNING CORPORATION Material Safety Data Sheet

Page: 7 of 8

MOLYKOTE(R) LONGTERM 2 PLUS

Warning: This product contains the following chemical(s) listed by the State of California under the Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65) as being known to cause cancer, birth defects or other reproductive harm.

None known. Massachusetts CAS Number 7782-42-5 Wt % 1.0 - 5.0 Component Name Graphite

New Jersey CAS Number 64741-96-4 64742-65-0 64742-54-7 64741-88-4 None 7620-77-1 None 8001-78-3 64742-52-5 Wt % 30.0 - 60.0 15.0 - 40.0 15.0 - 40.0 15.0 - 40.0 7.0 - 13.0 5.0 - 10.0 1.0 - 5.0 1.0 - 5.0 0.1 - 1.0 Component Name Solvent refined heavy naphthenic distillate (petroleum) Solvent dewaxed heavy paraffinic petroleum distillate Hydrotreated heavy paraffinic petroleum distillate Solvent-refined heavy paraffinic petroleum distillate Synthetic Sperm Oil 12-Hydroxy lithium stearate Vendor proprietary formulation Hydrogenated castor oil Hydrotreated heavy naphthenic petroleum distillate

Pennsylvania CAS Number 64741-96-4 64742-65-0 64742-54-7 64741-88-4 None 7620-77-1 Wt % 30.0 - 60.0 15.0 - 40.0 15.0 - 40.0 15.0 - 40.0 7.0 - 13.0 5.0 - 10.0 Component Name Solvent refined heavy naphthenic distillate (petroleum) Solvent dewaxed heavy paraffinic petroleum distillate Hydrotreated heavy paraffinic petroleum distillate Solvent-refined heavy paraffinic petroleum distillate Synthetic Sperm Oil 12-Hydroxy lithium stearate

DOW CORNING CORPORATION Material Safety Data Sheet

Page: 8 of 8

MOLYKOTE(R) LONGTERM 2 PLUS

7782-42-5 1.0 - 5.0 Graphite

16. OTHER INFORMATION Prepared by: Dow Corning Corporation These data are offered in good faith as typical values and not as product specifications. No warranty, either expressed or implied, is hereby made. The recommended industrial hygiene and safe handling procedures are believed to be generally applicable. However, each user should review these recommendations in the specific context of the intended use and determine whether they are appropriate. (R) indicates Registered Trademark

FORMAT: USA PRODUCT: IS808

MATERIAL SAFETY DATA SHEET SILICONE INDUSTRIAL SEALANT

-----------------------------------------------------------------------------1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

------------------------------------------------------------------------------

MANUFACTURED BY: GE SILICONES 260 HUDSON RIVER ROAD WATERFORD, NY 12188

SUPPLIED BY: GE SILICONES 260 HUDSON RIVER ROAD WATERFORD, NY 12188

EMERGENCY PHONE (24 HRS) (518) 237-3330

EMERGENCY PHONE (24 HRS) (518) 237-3330

REVISED: PREPARER:

04/18/03 B. JAVOREK SILICONE RUBBER

CHEMICAL FAMILY/USE: FORMULA: MIXTURE

-----------------------------------------------------------------------------2. COMPOSITION/INFORMATION ON INGREDIENTS

------------------------------------------------------------------------------

PRODUCT COMPOSITION/ CAS REG NO. -------------------1. HAZARDOUS

APPROX. WGT. % TWA

ACGIH TLV STEL TWA

OSHA PEL STEL UNITS

------- ------ ------ ------ ------ -----

OCTAMETHYLCYCLOTETRASILOXANE 556-67-2 TREATED FUMED SILICA 68611-44-9 5-10 10 NE 15 NE MG/M3 1-5 5 PPM NE GE REC NE GUIDE

METHYLTRIACETOXYSILANE 4253-34-3 2. NON-HAZARDOUS 1-5 10(R) NE 10(R) NE PPM

COPYRIGHT GENERAL ELECTRIC CO.

page: 1

DIMETHYL POLYSILOXANE SILANOL/ST 70131-67-8 60-80 NA NE NA NE NA

SILANOL/STPD SILOXANE W/ME SILSQXNS 68554-67-6 5-10 NF NE NF NE NA

See Section 15 for description of any WHMIS Trade Secret(s).

-----------------------------------------------------------------------------3. HAZARDS IDENTIFICATION

------------------------------------------------------------------------------

EMERGENCY OVERVIEW: WARNING! Irritating to skin, eyes, and respiratory tract. May be harmful if swallowed. Adverse liver and reproductive effects reported in animals. Vinegar odor Clear solid POTENTIAL HEALTH EFFECTS: INGESTION: May cause stomach discomfort. May be harmful if swallowed. Not an expected route of exposure. SKIN CONTACT: Uncured product contact will irritate lips, gums and tongue. Uncured product contact may irritate the skin. INHALATION: Causes mild respiratory irritation. Applies only in uncured state. EYE CONTACT: Uncured product contact irritates eyes. MEDICAL CONDITIONS AGGRAVATED: None known. SUBCHRONIC (TARGET ORGAN) EFFECTS: Reproductive disorders.

COPYRIGHT GENERAL ELECTRIC CO.

page: 2

May cause liver effects. CHRONIC EFFECTS/CARCINOGENICITY: This product or one of its ingredients present 0.1% or more is NOT listed as a carcinogen or suspected carcinogen by NTP, IARC, or OSHA. PRODUCTS/INGREDIENTS This space reserved for special use. PRINCIPLE ROUTES OF EXPOSURE: Dermal - skin. Eyes. Inhalation. OTHER: Acetic acid released during curing. Octamethylcyclotetrasiloxane Ingestion: Rodents given large doses via oral gavage of

octamethylcyclotetrasiloxane (1600 mg/kg day, 14 days) developed increased liver weights relative to unexposed control animals due to hepatocellular hyperplasia (increased number of liver cells which appeared normal) as well as hypertrophy (increased cell size).

Inhalation: In inhalation studies, laboratory rodents exposed to octamethylcyclotetrasiloxane (300 ppm five days week, 90 days) developed increased liver weights in female animals relative to unexposed control animals. When the exposure was stopped, liver Microscopic exami-

weights returned to normal.

nation of the liver cells did not show any evidence of pathology. Inhalation studies utilizing

laboratory rabbits and guinea pigs showed no effects on liver weights. Inhalation exposures

typical of industrial usage (5-10 ppm) showed no toxic effects in rodents.

Range finding reproductive studies were conducted (whole body inhalation, 70 days prior to mating,

COPYRIGHT GENERAL ELECTRIC CO.

page: 3

through mating, gestation and lactation) with octamethylcyclotetrasiloxane (D4). Rats were exposed to 70 and 700 ppm. there was In the 700 ppm group,

a statistically significant reduction in No D4

mean litter size and in implantation sites.

related clinical signs were observed in the pups and no exposure related pathological findings were found.

Interim results from a two generation reproductive study in rats exposed to 500 and 700 ppm D4 (whole body inhalation, 70 days prior to mating, through mating, gestation and lactation) resulted in a statically significant decrease in live mean litter size as well as extended periods of offspring delivery (dystocia). These results were

not observed at the 70 and 300 ppm dosing levels.

Preliminary results from an ongoing 24-month combined chronic/ongogenicity study in rats exposed to 10, 30, 150, or 700 PPM D4 showed test-article related effects in the kidney (male and female) and uterus of rats exposed for 12 to 24 months. effects include increased kidney weight and severity of chronic nephropathy, increased uterine weight, increased incidence of endometrial cell hyperplasia, and an increased incidence of endometrial adenomas. All of these effects were These

limited to the 700 PPM exposure group.

The relevance of these data to humans is unclear. Further studies are ongoing.

In developmental toxicity studies, rats and rabbits were exposed to octamethylcyclotetrasiloxane at concentrations up to 700 ppm and 500 ppm respectively. No teratogenic effects (birth

COPYRIGHT GENERAL ELECTRIC CO.

page: 4

defects) were observed in either study.

This product contains methylpolysiloxanes which can generate formaldehyde at approximately 300 degrees Fahrenheit (150'C) and above, in atmospheres which contain oxygen. Formaldehyde

is a skin and respiratory sensitizer, eye and throat irritant, acute toxicant, and potential cancer hazard. formaldehyde is available from GE Silicones. An MSDS for

-----------------------------------------------------------------------------4. FIRST AID MEASURES

------------------------------------------------------------------------------

INGESTION: Do not induce vomiting. Slowly dilute with 1-2 glasses of Never give any-

water or milk and seek medical attention. thing by mouth to an unconscious person. SKIN:

To clean from skin, remove completely with a dry cloth or paper towel, before washing with detergent and water. Get medical attention if irritation persists. INHALATION: If inhaled, remove to fresh air. If not breathing give If breathing is

artificial respiration using a barrier device. difficult give oxygen. EYES: Get medical attention.

In case of contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention if irritation persists. NOTE TO PHYSICIAN: None known.

------------------------------------------------------------------------------

COPYRIGHT GENERAL ELECTRIC CO.

page: 5

5.

FIRE FIGHTING MEASURES

------------------------------------------------------------------------------

FLASH POINT: METHOD IGNITION TEMP

NA : :

(C) NA NA UNK

(F)

(C) UNK UNK UNK NO

(F)

FLAMMABLE LIMITS IN AIR - LOWER (%): FLAMMABLE LIMITS IN AIR - UPPER (%): SENSITIVITY TO MECHANICAL IMPACT (Y/N): SENSITIVITY TO STATIC DISCHARGE:

Sensitivity to static discharge is not expected. EXTINGUISHING MEDIA: All standard firefighting media SPECIAL FIREFIGHTING PROCEDURES: Firefighters must wear NIOSH/MSHA approved positive pressure self-contained breathing apparatus with full face mask and full protective clothing.

-----------------------------------------------------------------------------6. ACCIDENTAL RELEASE MEASURES

------------------------------------------------------------------------------

1 ACTION TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Wipe, scrape or soak up in an inert material and put in a container for disposal. Wash walking surfaces with detergent and water to reduce slipping hazard. Wear proper protective equipment as specified in the protective equipment section. Increase area ventilation.

-----------------------------------------------------------------------------7. HANDLING AND STORAGE

COPYRIGHT GENERAL ELECTRIC CO.

page: 6

------------------------------------------------------------------------------

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Avoid contact with skin and eyes. Remove contact lenses before using sealant. Do not handle lenses until all sealant has been cleaned from the fingertips, nails and cuticles. Residual sealant may remain on

fingers for several days and transfer to lenses and cause severe eye irritation. Product releases acetic acid during application and curing. Use mechanical ventilation to stay below TLV of 10 ppm acetic acid. Store away from heat, sources of ignition, and incompatibles. Keep away from children.

-----------------------------------------------------------------------------8. EXPOSURE CONTROLS/PERSONAL PROTECTION

------------------------------------------------------------------------------

ENGINEERING CONTROLS: Showers and eyewash stations. RESPIRATORY PROTECTION: If exposure limits are exceeded or respiratory irritation is experienced, NIOSH/MSHA approved respiratory protection should be worn. Supplied air respirators may be required for Respiratory protection See "Ventilation" below.

non-routine or emergency situations.

must be provided in accordance with OSHA regulations (see 29 CFR 1910.134). PROTECTIVE GLOVES: Cloth gloves. EYE AND FACE PROTECTION: Safety glasses. OTHER PROTECTIVE EQUIPMENT: Wear eye protection and protective clothing.

COPYRIGHT GENERAL ELECTRIC CO.

page: 7

VENTILATION: Ventilation and other forms of engineering controls are preferred for controlling exposures. Respiratory protection

may be needed for non-routine or emergency situations. 1

-----------------------------------------------------------------------------9. PHYSICAL AND CHEMICAL PROPERTIES

------------------------------------------------------------------------------

PRODUCT INFORMATION: BOILING POINT : NA NA NA NA NA SOLID ACETIC ACID TRANSLUCENT UNK NA <1 1.04 1040 NA NA 20 INSOLUBLE TOLUENE (C) NA (C) NA (F) (F) (C) NA (F)

VAPOR PRESSURE(20 C)(MM HG): VAPOR DENSITY (AIR=1) FREEZING POINT MELTING POINT PHYSICAL STATE ODOR COLOR ODOR THRESHOLD (PPM) % VOLATILE BY VOLUME : : : : : : : :

EVAP. RATE(BUTYL ACETATE=1): SPECIFIC GRAVITY (WATER=1) : DENSITY (KG/M3) ACID/ALKALINITY (MEQ/G) PH : : :

VOC EXCL.H2O & EXEMPTS(G/L): SOLUBILITY IN WATER (20 C) :

SOLUBILITY IN ORGANIC SOLVENT (STATE SOLVENT):

-----------------------------------------------------------------------------10. STABILITY AND REACTIVITY

------------------------------------------------------------------------------

COPYRIGHT GENERAL ELECTRIC CO.

page: 8

STABILITY:

STABLE WILL NOT OCCUR

HAZARDOUS POLYMERIZATION:

HAZARDOUS THERMAL DECOMPOSITION/COMBUSTION PRODUCTS: Carbon monoxide. Carbon dioxide. Silicon dioxide. Acetic acid. Formaldehyde. INCOMPATIBILITY (MATERIALS TO AVOID): None known. CONDITIONS TO AVOID: None known.

-----------------------------------------------------------------------------11. TOXICOLOGICAL INFORMATION

------------------------------------------------------------------------------

OCTAMETHYLCYCLOTETRASILOXANE ACUTE ORAL LD50 (MG/KG): ACUTE DERMAL LD50 (MG/KG): ACUTE INHALATION LC50 (MG/L): OTHER: Non-irritating to the skin (human). AMES TEST: >64,000 (RAT) >16,000 (RBT) >41MG/L/6HR(RAT)

TREATED FUMED SILICA ACUTE ORAL LD50 (MG/KG): ACUTE DERMAL LD50 (MG/KG): ACUTE INHALATION LC50 (MG/L): OTHER: None. >10,000MG/KG (RAT) NA NA

COPYRIGHT GENERAL ELECTRIC CO.

page: 9

AMES TEST:

METHYLTRIACETOXYSILANE ACUTE ORAL LD50 (MG/KG): ACUTE DERMAL LD50 (MG/KG): ACUTE INHALATION LC50 (MG/L): OTHER: None. 2,060 (RAT) NONE FOUND NONE FOUND

AMES TEST:

DIMETHYL POLYSILOXANE SILANOL/ST ACUTE ORAL LD50 (MG/KG): ACUTE DERMAL LD50 (MG/KG): ACUTE INHALATION LC50 (MG/L): OTHER: Non-irritating to skin (rbt). AMES TEST: RAT >40,000 UNKNOWN RAT >535 MG/L (4HR)

SILANOL/STPD SILOXANE W/ME SILSQXNS ACUTE ORAL LD50 (MG/KG): ACUTE DERMAL LD50 (MG/KG): ACUTE INHALATION LC50 (MG/L): OTHER: None. >40,000 RAT,ESTM. NONE FOUND >535 MG/L ESTM.

AMES TEST:

-----------------------------------------------------------------------------12. ECOLOGICAL INFORMATION

------------------------------------------------------------------------------

ECOTOXICOLOGICAL INFORMATION: CHEMICAL FATE INFORMATION:

No data at this time No data at this time

COPYRIGHT GENERAL ELECTRIC CO.

page: 10

1 -----------------------------------------------------------------------------13. DISPOSAL CONSIDERATIONS

------------------------------------------------------------------------------

DISPOSAL METHOD: Disposal should be made in accordance with federal, state and local regulations.

-----------------------------------------------------------------------------14. TRANSPORT INFORMATION

------------------------------------------------------------------------------

DOT SHIPPING NAME: DOT HAZARD CLASS: DOT LABEL(S): UN/NA NUMBER: PLACARDS: IATA: NOT REGULATED BY IATA IMO IMDG-code: EMS No: NA NONE NONE NONE

NONE NOT DOT REGULATED

NOT REGULATED FOR OCEAN TRANSPORTATION

EUROPEAN CLASS: RID (OCTI): ADR (ECE) : RAR (IATA): NA NA NA

-----------------------------------------------------------------------------15. REGULATORY INFORMATION

------------------------------------------------------------------------------

COPYRIGHT GENERAL ELECTRIC CO.

page: 11

SARA SECTION 302: None Found SARA (311,312) HAZARD CLASS: ACUTE HEALTH HAZARD CHRONIC HEALTH HAZARD SARA (313) CHEMICALS: NONE CPSC CLASSIFICATION: NONE WHMIS HAZARD CLASS: D2A D2B VERY TOXIC MATERIALS TOXIC MATERIALS NA

WHMIS TRADE SECRET: None EXPORT: SCHDLE B/HTSUS: 3206.49 ECCN: EAR99 HAZARD RATING SYSTEMS 1 NFPA HMIS FLAMMABILITY 0 , REACTIVITY 0 , HEALTH 1 3214.10 Mastic Based on Rubber

Silicone Color Concentrate EAR99

HEALTH = 1, FLAMMABILIITY = 0 , REACTIVITY = 0

CALIFORNIA PROPOSITION 65: NONE

-----------------------------------------------------------------------------16. OTHER INFORMATION

------------------------------------------------------------------------------

These data are offered in good faith as typical values and not as product specifications. No warranty, either expressed or implied, is made. The recommended industrial hygiene and safe

handling procedures are believed to be generally applicable. However, each user should review these recommendations in the

COPYRIGHT GENERAL ELECTRIC CO.

page: 12

specific context of the intended use and determine whether they are appropriate. ................................................................ C = ceiling limit estimated not applicable none established none determined NEGL = NF = negligible none found unknown recommended recomm. By vendor skin trade secret recommended mist not tested

EST= NA = NE = ND =

UNKN = REC V SKN TS R MST NT = = = = = = =

By-product = reaction byproduct, TSCA inventory status not required under 40 CFR part 720.30(h-2) STEL = short term exposure limit

................................................................ All chemical substances in this material are included on or exempted from listing on the TSCA inventory. *

COPYRIGHT GENERAL ELECTRIC CO.

page: 13

TWO-COMPONENT A-COMPONENT

(Includes Quick Cure, Slow Rise, E-84 Class 1, Mining, Pour in Place and High Density)

A16178A

Issue Date: 03/05 Last Rev: 04/05-1 Prepared By: T. Eberling

MATERIAL

1. IDENTIFICATION

SAFETY

DATA

SHEET

Chemical Product A-Component for Two-Component Polyurethane Foam System Manufacturer FOMO PRODUCTS, INC. P. O. Box 1078 Norton, Ohio 44203 Emergency Overview Product Information: 1-800-321-5585. In Ohio and outside the United States call (330) 753-4585 Transportation Emergency: CHEMTREC 1-800-424-9300. Two-Component A-Component is registered by the manufacturer, FOMO PRODUCTS, INC. International Transportation Emergency: CHEMTREC (703) 527-3887 Product is a urethane foam component that contains a liquified compressed gas blowing agent (Non-Flammable Compressed Gas). Containers should not be heated above 120°F (49°C) to avoid excessive pressure build-up. 2. COMPOSITION Chemical Name (common names) 1,1,1,2- Tetrafluoroethane (Non-Flammable Compressed Gas, HFC, Fluorocarbon) 134a 4,4' - Diphenylmethane Diisocyanate (MDI) Higher Oligomers of MDI (Polymeric MDI) CAS Number 811-97-2 Percentage 5 to 10 percent LD50 NA LC50 NA

101-68-8

30 to 60 percent

NA

NA

9016-87-9

30 to 60 percent

NA

NA

(NOTE: See Section 8 of this MSDS for Exposure Guidelines) 3. HAZARDS IDENTIFICATION Physical Hazards Storage temperature should not exceed 120°F (49°C) in order to avoid excessive pressure build-up and possible release of contents. Also, MDI will react with water to form CO2 and water insoluble polyureas. This reaction may be vigorous at elevated temperatures, and could cause dangerous pressure build-up in tightly sealed containers. Liquid contents froth when released from containers. A-Component has strong adhesive characteristics. If accidental contact occurs, follow the appropriate first aid procedure described in Section 4 of this MSDS. Potential Health Effects The primary adverse health effects of this product are related to the Polymeric Isocyanate (MDI) component, and, to a lesser degree, the Fluorocarbon (134a) component. Therefore, adequate ventilation and respiratory protection should be provided to avoid exceeding exposure limits listed in Section 8 of this MSDS. Spraying MDI as a mist during application may increase vapor levels of this material.

TWO-COMPONENT A-COMPONENT

ISSUE DATE: 03/05

LAST REV: 04/05-1

PAGE 2 OF 4

Entry Route: Effects of Overexposure Inhalation: May irritate mucous membranes with tightness in chest, coughing, or allergic asthma-like sensitivity. Extensive overexposure can lead to respiratory symptoms like bronchitis and pulmonary edema. These effects are usually reversible. Overexposure to 1,1,1,2 - Tetrafluoroethane may cause lightheadedness, headaches, or lethargy. Persons with cardiac arrhythmia may be at increased risk in severe exposure. Eyes: Skin: Ingestion: 4. FIRST AID Inhalation: If breathing difficulty is experienced, move to area free of exposure. Provide fresh air. If necessary, provide oxygen or artificial respiration by trained personnel and obtain medical attention. May be irritating to eyes. MDI contact can cause physical damage due to adhesive character. May cause localized irritation, reddening or swelling. Prolonged or repeated exposure may lead to sensitization and/or contact dermatitis. May cause irritation of mucous membranes in the mouth and digestive tract.

Eye Contact: Flush with clean water for at least 15 minutes and obtain medical attention. Skin Contact: Use a rag to remove liquid from skin and remove contaminated clothing. Use of a solvent, such as acetone (nail polish remover) or mineral spirits, may help in removing uncured foam residue from clothing or other surfaces (avoid eye contact). May cause mild irritation or temporary darkening of skin. Persistent washing with soap and water will eventually remove all residue. If irritation persists, obtain medical attention. Ingestion: Drink 1 to 3 glasses of water and seek immediate medical attention. Never give anything orally to an unconscious person.

. 5. FIRE FIGHTING MEASURES High temperatures will raise the pressure in the containers, which may lead to rupturing. Extinguishing media include: dry chemical, carbon dioxide, Halon 1211, chemical foam, or water spray if used in large quantities (water contamination will produce carbon dioxide). Wear self-contained breathing apparatus to protect against toxic decomposition by-products, including CO, CO2, NO, and traces of HCN. Cured foam is organic and, therefore, will burn in the presence of sufficient heat, oxygen and an ignition source. Main hazards associated with burning foam are similar to burning of other organic materials (wood, paper, cotton, etc.) and precautions against exposure should be taken accordingly. Avoid welding or other "hot work" in the vicinity of exposed cured foam. 6. ACCIDENTAL RELEASE MEASURES/DISPOSAL CONSIDERATIONS Wear skin, eye and respiratory protection. Soak up material with absorbent and shovel into chemical waste container. Loosely cover container and remove from work area. Decontaminate waste and spill area with a solution of 0.2 ­ 0.5% liquid detergent and 3 ­ 8% concentrated ammonium hydroxide in water (5 ­ 10% sodium bicarbonate may be substituted for ammonium hydroxide). Use 10 parts of solution for each part of the spill and allow to react for at least 10 minutes. Allow loosely covered container to stand for several days before disposing in accordance with all applicable federal, state and local regulations. Liquid residues may be mixed slowly with equal amounts of B-Component in a well ventilated area in order to form solid, low grade foam, which in most cases can be disposed of as a solid in normal waste streams. Never discard in a liquid state. Undamaged cylinders are returnable by following manufacturer's instructions and all regulatory requirements. 7. HANDLING AND STORAGE Store in a cool, dry place. Ideal storage temperature is 60°F to 80°F (15.5°C to 26.6°C). Storage above 90°F (32.2°C) will shorten the shelf life. Protect unused product from freezing. Storage below 55°F (12.7°C) may affect foam quality if chemicals are not warmed to room temperature before using. Protect containers from physical abuse.

TWO-COMPONENT A-COMPONENT

ISSUE DATE: 03/05

LAST REV: 04/05-1

PAGE 3 OF 4

8. EXPOSURE CONTROLS/PERSONAL PROTECTION Read all product instructions before using. Personal protective equipment should include (impervious gloves, protective eye wear and suitable work clothes). Adequate ventilation should also be employed so that vapor levels do not exceed recommended guidelines. If vapor levels are expected to exceed these guidelines, use NIOSH approved, positive pressure, supplied air respirator or a negative pressure half mask with organic vapor cartridges and dust/mist pre-filters. Exercise good personal hygiene, wash thoroughly after each use. Exposure Guidelines 4,4' ­ Diphenylmethane Diisocyanate (MDI) Higher Oligomers of MDI 1,1,1,2 - Tetrafluoroethane (Non-Flammable Compressed Gas, HFC Fluorocarbon 134a) OSHA .020 ppm ceiling .200 mg/m3 ceiling None Established None Established ACGIH .005 ppm TWA .051 mg/m3 TWA None Established None Established

(None of the components in this product are listed by IARC, NTP, OSHA or ACGIH as a carcinogen). 9. PHYSICAL AND CHEMICAL PROPERTIES Physical Appearance Odor Specific Gravity Boiling Point Flash Point Vapor Pressure Solubility in Water Explosion Data : : : : : : : : Amber to dark brown liquid. Froths to an off white to yellowish color when released from container. (Note; Appearance may differ with the introduction of a dye or colorant). Slight musty odor Approximately 1.2 (H2O = 1) 1,1,1,2 - Tetrafluoroethane (Non-Flammable Compressed Gas, HFC Fluorocarbon 134a) boils at -15°F (-26°C). MDI boils at 406°F (208°C). 1,1,1,2 - Tetrafluoroethane (HFC 134a); none. MDI; 390°F (199°C). Contents under pressure have vapor pressure greater than 50 psig/345 kPa. For MDI liquid less than 10 mm Hg at 77°F (25°C). Insoluble, reacts slowly with water to liberating traces of CO2. Contents are not known to be sensitive to mechanical impact or static discharge.

10. STABILITY AND REACTIVITY This product is considered stable under normal and anticipated storage and handling conditions. Do not store above 120°F (49°C). For longest shelf life, avoid storage above 90°F (32.2°C). Avoid alcohols, strong bases or amines and metal compounds (such as small particle metal catalysts). Avoid contamination with water.

TWO-COMPONENT A-COMPONENT

ISSUE DATE: 03/05

LAST REV: 04/05-1

PAGE 4 OF 4

11. TRANSPORTATION Shipping Information Containers Less Than 1000 cu. cm. (1 liter) Ground Consumer Commodity ORM-D (On Shipper Carton) Consumer Commodity Two-Component AComponent (On Shipping Document) UN1950 Aerosols, non-flammable 2.2 (Non-flammable Gas Label) UN1950 AEROSOLS , (Limited Quantity) Class 2 IMDG Volume 2; Page # 93 N/A Emergency Response Guide Numbers - Consumer Commodity # 171. For Aerosols and Compressed Gas # 126. Containers Greater Than 1000 cu. cm. (1 liter) UN1956 Compressed gas n.o.s. (Fluorocarbon) 2.2 (Non-Flammable Gas Label)

Air

UN1956 Compressed gas n.o.s. (Fluorocarbon) 2.2 (Non-flammable Gas Label) UN1956 COMPRESSED GAS N.O.S (Fluorocarbon) 2.2 IMDG Volume # 2; Page # 93

Water

Exceptions Note

12. REGULATORY Toxic Substances Control Act (TSCA)/Domestic Substances List (DSL): All ingredients are listed on the TSCA inventory, as well as the Canadian Domestic Substances List. SARA Title III: Contains Diphenylmethane Diisocyanate (CAS #101-68-8) which is subject to the reporting requirements of SARA Title III. Applicability must be determined by end user. Proposition 65: Based on information currently available, this product is not known to contain detectable amounts of any chemicals currently listed under California Proposition 65. V.O.C. Content: Based on the current EPA definition of volatile organic compound, this product does not have any V.O.C. content. 13. OTHER NFPA: HMIS: Fire 1; Health 3; Reactivity 1 Flammability 1; Health 3: Reactivity 1

The information and recommendations set forth herein are presented in good faith and believed to be correct as of the date hereof. The manufacturer makes no representations as to the completeness or accuracy thereof. Information is supplied upon the condition that the persons receiving it will make their own determination as to its suitability for their purposes prior to use. In no event will the manufacturer be responsible for damages of any nature whatsoever resulting from the use of or reliance upon information. No representations or warranties, either expressed or implied, of merchantability or fitness for a particular use are made hereunder with respect to this information or the product to which information refers.

Information contained herein is deemed to be reliable, conservative and accurate. Fomo Products, Inc. reserves the right to change the design, specifications or any other features at any time and without notice, while otherwise maintaining regulatory compliance.

LAST REVISION APPROVED BY A16178-A

: :

04/05-1 T. EBERLING

TWO-COMPONENT B-COMPONENT

(Includes Quick Cure, Slow Rise, E-84 Class 1, Mining, Pour in Place and High Density)

A16178-B

Issue Date: 03/05 Last Rev: 04/05-1 Prepared By: T. Eberling

MATERIAL

1. IDENTIFICATION

SAFETY

DATA

SHEET

Chemical Product B-Component for Two-Component Polyurethane Foam System Manufacturer FOMO PRODUCTS, INC. P. O. Box 1078 Norton, Ohio 44203 Emergency Overview Product Information: 1-800-321-5585. In Ohio and outside the United States call (330) 753-4585 Transportation Emergency: CHEMTREC 1-800-424-9300. Two-Component B-Component is registered by the manufacturer, FOMO PRODUCTS, INC. International Transportation Emergency: CHEMTREC (703) 527-3887 Product is a urethane foam component that contains a liquified compressed gas blowing agent (Non-Flammable Compressed Gas). Containers should not be heated above 120°F (49°C) to avoid excessive pressure build-up. 2. COMPOSITION Chemical Name (common names) 1,1,1,2- Tetrafluoroethane (Non-Flammable Compressed Gas, HFC, Fluorocarbon) 134a Non-Hazardous Proprietary Polyol Blend CAS Number 811-97-2 Percentage 10 to 30 percent LD50 NA LC50 NA

Not Available This Section

60 to 100 percent

NA

NA

(NOTE: See Section 8 of this MSDS for Exposure Guidelines) 3. HAZARDS IDENTIFICATION Physical Hazards Storage temperature should not exceed 120°F (49°C) in order to avoid excessive pressure build-up and possible release of contents. Liquid contents froth when released from containers. If accidental contact occurs, follow the appropriate first aid procedure described in Section 4 of this MSDS. Potential Health Effects The mixture has not been tested. However, it is assumed that the mixture presents the same health hazards as do the components present at a one percent or greater level (1,1,1,2 ­ Tetrafluoroethane, 134a). Adequate ventilation should be provided to avoid exceeding the exposure limits listed in Section 8 of this MSDS.

TWO-COMPONENT B-COMPONENT

ISSUE DATE: 03/05

LAST REV: 04/05-1

PAGE 2 OF 4

Entry Route: Effects of Overexposure Inhalation: Vapor reduces oxygen available for breathing and is heavier than air. May cause dizziness, headaches, lethargy, etc. Inhalation of high concentrations of vapor is harmful and may cause heart irregularities. Persons with cardiac arrhythmia may be at increased risk in severe exposure. Eyes: Skin: Ingestion: 4. FIRST AID Inhalation: If breathing difficulty is experienced, move to area free of exposure. Provide fresh air. If necessary, provide oxygen or artificial respiration by trained personnel and obtain medical attention. May be irritating to eyes. May cause localized irritation, reddening or swelling. Direct, severe, or prolonged exposure may lead to frostbite. May cause irritation of mucous membranes in the mouth and digestive tract.

Eye Contact: Flush with clean water for at least 15 minutes and obtain medical attention. Skin Contact: Use a rag or paper towel to remove liquid from skin and wash thoroughly with soap and water. Remove contaminated clothing. If irritation develops, use a mild skin cream. If irritation persists, obtain medical attention. Ingestion: Drink 1 to 3 glasses of water and seek immediate medical attention. Never give anything orally to an unconscious person.

5. FIRE FIGHTING MEASURES High temperatures will raise the pressure in the containers, which may lead to rupturing. Extinguishing media include: dry chemical, carbon dioxide, Halon 1211, chemical foam, or water spray if used in large quantities. Wear self-contained breathing apparatus to protect against toxic decomposition by-products, including CO, CO2, NO, and traces of HCN. Cured foam is organic and, therefore, will burn in the presence of sufficient heat, oxygen and an ignition source. Main hazards associated with burning foam are similar to burning of other organic materials (wood, paper, cotton, etc.) and precautions against exposure should be taken accordingly. Avoid welding or other "hot work" in the vicinity of exposed cured foam. 6. ACCIDENTAL RELEASE MEASURES/DISPOSAL CONSIDERATIONS Wear skin and eye protection. Provide ventilation and isolate area. Absorb spill with sawdust or vermiculite and dispose of in accordance with all applicable federal, state, and local regulations. Wash spill area thoroughly with soap and water. Avoid uncontrolled reactions with isocyanates (such as A-Component). Liquid residues may be mixed slowly with A-Component to react and produce low-grade foam, which in most cases can be disposed of as a solid in normal waste streams. Never discard in a liquid state. Undamaged cylinders are returnable by following manufacturer's instructions and all regulatory requirements. 7. HANDLING AND STORAGE Store in a cool, dry place. Ideal storage temperature is 60°F to 80°F (15.5°C to 26.6°C). Storage above 90°F (32.2°C) will shorten the shelf life. Protect unused product from freezing. Storage below 55°F (12.7°C) may affect foam quality if chemicals are not warmed to room temperature before using. Protect containers from physical abuse.

TWO-COMPONENT B-COMPONENT

ISSUE DATE: 03/05

LAST REV: 04/05-1

PAGE 3 OF 4

8. EXPOSURE CONTROLS/PERSONAL PROTECTION Read all product instructions before using. Personal protective equipment should include (impervious gloves, protective eye wear and suitable work clothes). Adequate ventilation should also be employed so that vapor levels do not exceed recommended guidelines. If vapor levels are expected to exceed these guidelines, use a NIOSH approved, positive pressure, supplied air respirator or a negative pressure half mask with organic vapor cartridges and dust/mist pre-filters. Exercise good personal hygiene, wash thoroughly after each use. Exposure Guidelines 1,1,1,2 - Tetrafluoroethane (Non-Flammable Compressed Gas, HFC Fluorocarbon 134a) OSHA None Established ACGIH None Established

(None of the components in this product are listed by IARC, NTP, OSHA or ACGIH as a carcinogen). 9. PHYSICAL AND CHEMICAL PROPERTIES Physical Appearance : Light yellow to amber colored liquid. Froths to an off white to yellowish color when released from container. (Note; Appearance may differ with the introduction of a dye or colorant). Slight fluorocarbon and amine odor. Approximately 1.2 (H2O = 1) 1,1,1,2 - Tetrafluoroethane (Non-Flammable Compressed Gas, HFC Fluorocarbon, 134a) boils at -15°F (-26°C). Other components boil at temperatures greater than 200°F (93.3°C). 1,1,1,2 - Tetrafluoroethane (HFC 134a); none. For other components ­ not determined. Contents under pressure have vapor pressure greater than 50 psig /345 kPa. After release from container, the vapor pressure is very low (not determined). Partly soluble, does not react. Contents are not known to be sensitive to mechanical impact or static discharge.

Odor Specific Gravity Boiling Point

: : :

Flash Point Vapor Pressure Solubility in Water Explosion Data

: : : :

10. STABILITY AND REACTIVITY This product is considered stable under normal and anticipated storage and handling conditions. Do not store above 120°F (49°C). For longest shelf life, avoid storage above 90°F (32.2°C). Avoid uncontrolled reactions with isocyanates (i.e. AComponent).

TWO-COMPONENT B-COMPONENT

ISSUE DATE: 03/05

LAST REV: 04/05-1

PAGE 4 OF 4

11. TRANSPORTATION Shipping Information Containers Less Than 1000 cu. cm. (1 liter) Ground Consumer Commodity ORM-D (On Shipper Carton) Consumer Commodity Two-Component BComponent (On Shipping Document) UN1950 Aerosols, non-flammable 2.2 (Nonflammable Gas Label). UN1950 AEROSOLS, (Limited Quantity) Class 2 IMDG Volume 2; Page # 93 N/A Emergency Response Guide Numbers - Consumer Commodity # 171. For Aerosols and Compressed Gas # 126. Containers Greater Than 1000 cu. cm. (1 liter) UN1956 Compressed gas n.o.s. (Fluorocarbon) 2.2 (Non-Flammable Gas Label)

Air Water

UN1956 Compressed gas n.o.s. (Fluorocarbon) 2.2 (Non-flammable Gas Label). UN1956 COMPRESSED GAS N.O.S. (Fluorocarbon) 2.2 IMDG Volume 2; Page # 93

Exceptions Note

12. REGULATORY Toxic Substances Control Act (TSCA)/Domestic Substances List (DSL): All ingredients are listed on the TSCA inventory, as well as the Canadian Domestic Substances List. SARA Title III: No ingredients in this product are currently recognized as SARA Tittle III reportable. Proposition 65: Based on information currently available, this product is not known to contain detectable amounts of any chemicals currently listed under California Proposition 65. V.O.C. Content: Based on the current EPA definition of volatile organic compound, this product does not have any V.O.C. content. 13. OTHER NFPA: HMIS: Fire 1; Health 2; Reactivity 1 Flammability 1; Health 2; Reactivity 1

The information and recommendations set forth herein are presented in good faith and believed to be correct as of the date hereof. The manufacturer makes no representations as to the completeness or accuracy thereof. Information is supplied upon the condition that the persons receiving it will make their own determination as to its suitability for their purposes prior to use. In no event will the manufacturer be responsible for damages of any nature whatsoever resulting from the use of or reliance upon information. No representations or warranties, either expressed or implied, of merchantability or fitness for a particular use are made hereunder with respect to this information or the product to which information refers.

Information contained herein is deemed to be reliable, conservative and accurate. Fomo Products, Inc. reserves the right to change the design, specifications or any other features at any time and without notice, while otherwise maintaining regulatory compliance.

LAST REVISION APPROVED BY A16178-B

: :

04/05-1 T. EBERLING

Information

105 pages

Find more like this

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

752412