Read Microsoft Word - TDS_Imron_Elite_Basecoat_EB_E.doc text version

DuPontTM Imron® Elite

Basecoat (EB quality)

Type A two-component, 3.5 VOC, polyurethane basecoat. Description A high-performance, polyurethane basecoat that delivers premium appearance, excellent color match and excellent durability. Can be air or force-dried. Suggested Uses Designed for panel and overall applications. Not Recommended For Immersion service or over lacquer finishes. Compatibility With Other Coatings Compatible with all DuPont OEM / Commercial Finishes primers Dry Film Characteristics Chemical Resistance Weatherability Humidity Resistance Acid Resistance Alkali Resistance Solvent Resistance Abrasion Resistance Flexibility EXCELLENT EXCELLENT EXCELLENT EXCELLENT EXCELLENT EXCELLENT EXCELLENT EXCELLENT

Mix Ratio Combine components and mix thoroughly. Filter material prior to spray application. Two Component System DuPontTM Imron® Elite Basecoat (EB quality) DuPontTM 194STM Activator Parts by Volume 3 1

Add up to 2 oz. of DuPontTM 389STM Accelerator or 1 oz. DuPontTM 8989STM to activated gallon to improve pot life and dry time. Note: DuPontTM MasterTint® 8989STM will shorten pot life. Initial application viscosity: 10-18 seconds with #3 Zahn Cup, depending on color. Pot Life and Induction Time No induction time required. Pot life is 2 hrs at 70°F (21°C); 2-4 hrs at 70°F (21°C) with DuPontTM 389STM; 45 min at 70°F (21°C) with DuPontTM 8989STM. Additional Comments Heating activated material above 110°F (43°C) will cause the product to gel. Sanding is recommended for recoating if the basecoat is force dried or cured > 16 hours ambient. Add up to 1 oz. of MasterTint® 8989STM per RTS gal. to improve tape time when striping.

°F / °C

Application Conditions Do not apply if material, substrate or ambient temperature is less than 50°F (10°C) or above 110°F (43°C). The substrate must be at least 5°F (3°C) above the dew point. Relative humidity should be below 90%.

A DuPont OEM / Commercial Finishes Product

Copyright © 2010 DuPont. All rights reserved. The DuPont Oval Logo and all trademarks listed herein with ® or TM are trademarks or registered trademarks of E.I. du Pont de Nemours and Company or its affiliates.

Application Pressure pot application is recommended for best color match and performance. Apply DuPontTM Imron® Elite BCTM using a cross-coat technique. Spray a wet first coat using a top-to-bottom motion. Spray a medium-wet second coat using a side-to-side motion. Flash times between coats will vary between 30 seconds and 5 minutes. In general, the shorter the flash the smoother the appearance. DuPontTM Imron® Elite basecoat must be clear coated with DuPontTM Imron® Elite 8840STM Clear Coat or DuPontTM Imron® EZ-3460STM Clear Coat. Do not spray Imron® Elite BCTM if the paint temperature is less than 75°F (24°C). Use warm water or paint heaters to heat the paint to an optimum temperature of 85-95°F (29-35°C). Incase of fish eyes, add up to 1 oz. of DuPontTM 359STM Additive per RTS gallon for solid colors or 1 oz. DuPontTM VGF-70050TM for metallic colors. Do not use FEE. Purge lines with DuPontTM 3602STM Thinner or DuPontTM 8285STM Reducer. Gun Setup For pressure pot application set air pressure at 55 ­ 60 psi at the gun for solid colors and effect colors. Fluid delivery should be set for 10 ­ 12 fluid oz/min. For siphon gun application, set air pressure to 50 ­ 55 psi at the gun for solid and effect colors. Dry Time 77°F (25°C) & 50% Rh at recommended film thickness Dry to Touch Tack Free Tape Free Dry to Assemble W/out Accelerator 4-6 hrs 10-12 hrs 12-24 hrs 72 hrs With DuPontTM 389STM 1-2 hrs 2-4 hrs 4-6 hrs 72 hrs With DuPontTM 8989STM 0.5-1 hr 1-2 hrs 2-4 hrs 72 hrs

Application Equipment Pressure Pot (recommended) Gravity Feed HVLP Siphon Feed Air-Assisted Airless Airless Maximum Service Temperature 200°F (92°C) in continuous service Volume Solids ­ Will Vary By Color 46.8% average unactivated 52.3% average RTS mixed 3:1 with DuPontTM 194STM Activator Weight Solids ­ Will Vary By Color 58.1% average unactivated 62.0% average RTS mixed 3:1 with DuPontTM 194STM Activator Weight Per Gallon 9.15 lbs/gal average unactivated Suggested Dry Film Thickness Apply until hiding is achieved. Solid and effect colors: 1.0 ­ 1.5 mils DFT Theoretical Coverage Per Gallon 839 sq. ft./gal average @ 1 mil DFT

A DuPont OEM / Commercial Finishes Product

Copyright © 2010 DuPont. All rights reserved. The DuPont Oval Logo and all trademarks listed herein with ® or TM are trademarks or registered trademarks of E.I. du Pont de Nemours and Company or its affiliates.

Gloss High Color Available in solid, metallic and pearl colors Flash Point (Closed Cup) Below 80°F (27°C) Shelf Life 12 months minimum Application Solvents Ready to spray below 3.5 lbs/gal VOC upon activation. Further reduction will result in greater than 3.5 lbs/gal. Cleanup Solvents DuPontTM 3602STM Thinner DuPontTM 8685STM Reducer Environmental VOC content (lbs/gal) DuPontTM Imron® Elite Basecoat (EB quality) Mixed 3:1 with DuPontTM 194STM Activator LE 3.8 3.5 AP 3.8 3.5

For VOC Regulated Areas These directions refer to the use of products that may be restricted or require special mixing instructions in your area. Follow recommendations in the DuPont Compliant Products Chart for your area. Safety And Handling DuPont is committed to helping you develop and maintain a safe working environment. Carefully read the specific warnings and precautions printed on the labels of all DuPont products before handling and using. These products are for industrial use by trained professional painters only. Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.

01/10

A DuPont OEM / Commercial Finishes Product

Copyright © 2010 DuPont. All rights reserved. The DuPont Oval Logo and all trademarks listed herein with ® or TM are trademarks or registered trademarks of E.I. du Pont de Nemours and Company or its affiliates.

Information

Microsoft Word - TDS_Imron_Elite_Basecoat_EB_E.doc

3 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

1262916


You might also be interested in

BETA
Microsoft Word - TDS_Imron_6000_Basecoat_HL_E.doc
Description
Microsoft Word - 13550S_Aviation_Finishes rev2009.12.doc
Microsoft Word - TDS_Imron_5000_Topcoat_HK_E.doc
Microsoft Word - Imron6000.doc