Read Apec_2097_ISO.pdf text version

Apec 2097

Easy-flow grades / UV-stabilized, easy-release MVR (330°C/2.16kg) 8 cm³/10 min; high viscosity; easy release; UV stabilized; 'softening temperature (VST/B 120)=202 °C; injection molding - melt temperature 330 - 340°C; Lamp covers; Headlamp lenses

ISO Shortname Property

Rheological properties C Melt volume-flow rate Melt mass-flow rate C Molding shrinkage, parallel C Molding shrinkage, normal Mechanical properties (23 °C/50 % r. h.) C Tensile modulus C Yield stress C Yield strain C Nominal strain at break C Charpy impact strength C Charpy impact strength Flexural modulus Flexural strength Ball indentation hardness Thermal properties C Temperature of deflection under load C Temperature of deflection under load Vicat softening temperature Relative temperature index (Tensile strength) Relative temperature index (Tensile impact strength) Relative temperature index (Electric strength) C Coefficient of linear thermal expansion, parallel C Coefficient of linear thermal expansion, transverse C Burning behavior UL 94 (1.5 mm) C Oxygen index Glow wire test (GWFI) Electrical properties (23 °C/50 % r. h.) C Relative permittivity C Relative permittivity C Dissipation factor C Dissipation factor C Volume resistivity C Surface resistivity C Electrical strength C Comparative tracking index CTI Comparative tracking index CTI M Electrolytic corrosion Other properties (23 °C) C Water absorption (saturation value) C Water absorption (equilibrium value) C Density Material specific properties Refractive index Luminous transmittance (clear transparent materials) Procedure A 1 mm % ISO 489 ISO 13468-2 1.566 89 Water at 23 °C 23 °C; 50 % r. h. % % kg/m³ ISO 62 ISO 62 ISO 1183-1 0.3 0.12 1130 1 mm Solution A Solution B 100 Hz 1 MHz 100 Hz 1 MHz 10 10

-4 -4

Test Condition

Unit

Standard

typical Value

-

330 °C; 2.16 kg 330 °C; 2.16 kg 60x60x2 mm 60x60x2 mm

cm³/10 min g/10 min % %

ISO 1133 ISO 1133 ISO 294-4 ISO 294-4

8 8 0.9 0.9

1 mm/min 50 mm/min 50 mm/min 50 mm/min 23 °C -30 °C 2 mm/min 2 mm/min

MPa MPa % % kJ/m² kJ/m² MPa MPa N/mm²

ISO 527-1,-2 ISO 527-1,-2 ISO 527-1,-2 ISO 527-1,-2 ISO 179-1eU ISO 179-1eU ISO 178 ISO 178 ISO 2039-1

2450 76 6.9 > 50 N N 2450 110 130

1.80 MPa 0.45 MPa 50 N; 120 °C/h

°C °C °C °C °C °C

ISO 75-1,-2 ISO 75-1,-2 ISO 306 UL 746B UL 746B UL 746B ISO 11359-1,-2 ISO 11359-1,-2 UL 94 ISO 4589-2 IEC 60695-2-12

172 191 202 150 130 150 0.65 0.65 HB 25 800

23 to 55 °C 23 to 55 °C 1.5 mm Method A

10 /K 10 /K Class % °C

-4

-4

IEC 60250 IEC 60250 IEC 60250 IEC 60250 IEC 60093 IEC 60093 IEC 60243-1 IEC 60112 IEC 60112 IEC 60426

2.9 2.8 10 90 1E15 1E16 35 600 100 A1

Ohm·m Ohm kV/mm Rating Rating Rating

Page 1 of 3 pages

Apec

Edition 24.10.2012

®

ISO Datasheet

Apec 2097

Property

Processing conditions for test specimens C Injection molding-Melt temperature C Injection molding-Mold temperature C Injection molding-Injection velocity °C °C mm/s ISO 294 ISO 294 ISO 294 330 100 200

Test Condition

Unit

Standard

typical Value

-

C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350. Impact properties: N = non-break, P = partial break, C = complete break

Page 2 of 3 pages

Apec

Edition 24.10.2012

®

ISO Datasheet

Apec 2097

Disclaimer

Typical value These values are typical values only. Unless explicitly agreed in written form, the do not constitute a binding material specification or warranted values. Values may be affected by the design of the mold/die, the processing conditions and coloring/pigmentation of the product. Unless specified to the contrary, the property values given have been established on standardized test specimens at room temperature. General The manner in which you use and the purpose to which you put and utilize our products, technical assistance and information (whether verbal, written or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is imperative that you test our products, technical assistance and information to determine to your own satisfaction whether they are suitable for your intended uses and applications. This application-specific analysis must at least include testing to determine suitability from a technical as well as health, safety and environmental standpoint. Such testing has not necessarily been done by us. Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale which are available upon request. All information and technical assistance is given without warranty or guarantee, and is subject to change without notice. Any statement or recommendation not contained herein is unauthorized and shall not bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with patents covering any material or its use. No license is implied or in fact granted under the claims of any patent. With respect to health, safety and environment precautions, the relevant Material Safety Data Sheets (MSDS) and product labels must be observed prior to working with our products.

Publisher: Global Innovations - Polycarbonates Bayer MaterialScience AG, D-51368 Leverkusen, www.bayermaterialscience.com [email protected]

Page 3 of 3 pages

Apec

Edition 24.10.2012

®

ISO Datasheet

Information

3 pages

Find more like this

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

808063


You might also be interested in

BETA
ArticleFinalA4
ASTM Complete Index
339-350
STRENGTH OF MATERIALS LABORATORY MANUAL