Read Microsoft Word - R1108634.rtf text version

euxyl® K 727

Preservative for cosmetics & toiletries

Liquid preparation based on Methyldibromo Glutaronitrile, Methylchloroisothiazolinone, Methylisothiazolinone and Phenoxyethanol Broad, balanced spectrum of effect against bacteria, yeasts and moulds Effective even in very low use-concentrations Good head space protection On account of the synergism of the ingredients the levels of the individual ingredients can be kept far below their permitted max. concentrations Effective in pH ranges up to 8

Use / Use-concentration

Leave-on (i.e. creams, lotions etc.) Rinse-off (i.e. shampoos, bath preparations etc.) EU-INCI-declaration Phenoxyethanol Methyldibromo Glutaronitrile Methylchloroisothiazolinone Methylisothiazolinone

acc. schülkerecommendation 0.05 - 0.15 %

acc. EU / ASEAN Cosmetics Directive not to be used not to be used US-INCI-declaration Phenoxyethanol Methyldibromo Glutaronitrile Methylchloroisothiazolinone Methylisothiazolinone

acc. CIR (USA) max. 0.30 % max. 0.60 %

Recommended use-concentrations are based on average active content. Please pay attention to the corresponding certificate of analysis.

Individual ingredients without auxiliaries. For full INCI-declaration kindly contact us.

Active substance

INCI name Phenoxyethanol Methyldibromo Glutaronitrile Methylchloroisothiazolinone Methylisothiazolinone EINECS-Name: 2-Phenoxyethanol 2-Bromo-2-(bromomethyl)pentanedinitrile 5-Chloro-2-methyl-2H-isothiazol-3-one 2-Methyl-2H-isothiazol-3-one nearly colourless - dark yellow Liquid characteristic 1.075 - 1.081 g/ml 1.432 - 1.437 ca. 100 ° C > 100 ° C < 15 s ca. 14 mPa*s 15 g/l Non foaming (0.2 % in water) ca. 25 hPa CAS-No.: 122-99-6 35691-65-7 26172-55-4 2682-20-4 EC-No.: 204-589-7 252-681-0 247-500-7 220-239-6

Physico-chemical properties

Colour Form Odour Density (20 ° C) Refractive index (20 ° C) Initial boiling point Flash point (ISO 2719) Flow time (DIN 53211 - 20 ° C) Viscosity (Brookfield - 20 ° C) Water solubility (20 ° C) Foaming characteristics (DIN 53902) Vapour pressure (20 ° C)

Fields of application

The recommended use levels relate to the total formulation in each case. The values given are recommended guidelines. The optimum use level should be evaluated by means of a repeated challenge test (e.g. at schülke Technical and Microbiological dept). Recommended dosage 0.1 - 0.2 % Products which contain proteins, caseins, fresh cell extracts, repair complexes, or Emulsions similar, must in principle contain a higher proportion of preservative. Solutions (e.g. shampoos, bath preparations and 0.05 - 0.15 % hand cleansing preparations) Other uses Kindly contact us.

Indications for use

General Information Solubility Compatibility with surfactants Compatibility with sulphite ions Compatibility with nitrogen surfactants Compatibility with iron ions euxyl® K 727 is fully effective both in anionic as well as cationic and non-ionic systems. High pH values (> pH 8.0) should be avoided. Acidic pH values have no negative influence on the effectiveness. In water and non-polar solvents only limitedly soluble. In polar solvents unlimitedly soluble. euxyl® K 727 proved to have good compatibility with anionic surfactants such as sulphates, ether sulphates and sulphosuccinates, as well as with non-ionogenic surfactants. euxyl® K 727 is inactivated by sulphite ions. Excessive sulphite > 10 ppm must be avoided. With nitrogen surfactants, concentration- and product-dependent discolourations were observed, especially when exposed to high temperatures. In formulations as a result of the presence of iron ions, e.g. from mineral thickeners, yellow discolourations were observed. The tendency to discolouration can be reduced by adding complexing agents. euxyl® K 727 should in principle only be incorporated into the product to be preserved in the cooling phase at a temperature lower than 40 ° In practice, adding euxyl® K 727 together C. with the fragrance has proved effective.

Maximum use temperature

euxyl® K 727

Microbiological efficacy

euxyl® K 727 is equally effective against bacteria, yeasts and mould fungi. It is a typically biostatic product with the biocidal properties necessary for practical use. For euxyl® K 727 to perform effectively in destroying organisms in products already contaminated, a minimum contact time of 48 hours is necessary. Since the effect of euxyl® K 727 takes place through chemical reactions with the microorganisms, when it is used in heavily contaminated products loss of active ingredient must be taken into account. Good production hygiene, as well as the use of raw materials with low microorganism levels as a result of correct raw material control, are of course vital prerequisites for the production of microbiologically faultless finished products.

MIC

The efficacy of the product has been tested against the following microorganisms according to DGHM (German Society for Hygiene and Microbiology). Determination of the minimum inhibitory concentration in the serial dilution test produced the following values (MIC in % of the product): Bacteria (gram-negative) MIC Bacteria (gram-positive) MIC Yeasts MIC Burkholderia cepacia 0.06 Bacillus subtilis 0.03 Candida albicans 0.02 Enterobacter cloacae 0.06 Brevibacterium ammoniagenes 0.03 Saccharomyces cerevisiae 0.13 Escherichia coli 0.06 Staphylococcus aureus 0.06 Klebsiella pneumoniae 0.06 Streptococcus lactis 0.06 Proteus mirabilis 0.06 Moulds MIC Pseudomonas aeruginosa 0.06 Aspergillus niger 0.13 Pseudomonas fluorescens 0.03 Aspergillus oryzae 0.25 Pseudomonas putida 0.03 Microsporum gypseum 0.02 Pseudomonas stutzeri 0.03 Penicillium expansum 0.13 Penicillium funiculosum 0.03 Trichophyton mentagrophytes 0.02 Trichoderma virens 0.13

Compatibility*

compatible high-alloyed stainless steel (e. g. 1.4571), PVC (hard), polystyrene, polytetrafluoroethylene, ethylene-propylene-terpolymer, polyethylene, fluorinated rubber No significant difference to water to be avoided PVC (soft), polymethyl methacrylate (PMMA), metals other than mentioned, sealants and plastics other than mentioned Water incompatible materials

concentrate aqueous dilution (0.2 %)

*Compatibility has to be proved in each case

Environmental information

euxyl® K 727 contains only biodegradable components. Dilutions of euxyl® K 727 do not normally interfere with the operation of waste water treatment plants. The canisters and drums used by schülke are made of polyethylene (HDPE) and are labelled accordingly. The 1000 kg containers are covered by a return scheme that ensures collection of the used containers free of charge and appropriate reuse all over Europe. The labels are made of PE. schülke packaging materials contain no PVC and can be recycled. For further information please ask for our detailed environmental report.

Labelling

R-phrase(s) S-phrase(s) Labelling R22, R36/38, R43, R52/53 S24, S37 Xn (Harmful)

Transport & Storage

Dangerous goods UN-Number Packaging group Package sizes Shelf life Storage No 10 kg, 200 kg, 1000 kg 18 Months Protect from frost, heat and direct sunlight. Store at room temperature in the original container.

For further hazard instructions and safety advice please refer to the actual material safety data sheet.

schülke subsidiaries:

Belgium

S.A. Schülke & Mayr Belgium N.V 1830 Machelen Tel. +32-02-479 73 35 Fax +32-02-479 99 66

China

Schülke & Mayr GmbH Shanghai Representative Office Shanghai 200041 Tel. +86-21-62 17 29 95 Fax +86-21-62 17 29 97

France

S & M France 75341 Paris Cedex 07 Tel. +33-1-44 11 00 81 Fax +33-1-44 11 02 41

Italy

Schülke & Mayr Italia S.r.l. 20148 Milano Tel. +39-02-40 21 820 Fax +39-02-40 21 829

The Netherlands

Schülke & Mayr Benelux B.V. 2003 LM-Haarlem Tel. +31-23-535 26 34 Fax +31-23-536 79 70

Switzerland

Schülke & Mayr AG 8003 Zürich Tel. +44-466 55 44 Fax +44-466 55 33

The United Kingdom

Schülke & Mayr UK Ltd. Sheffield S9 1 AT Tel. +44-1142-54 35 00 Fax +44-1142-54 35 01

United States of America

schülke Inc. Mt. Arlington, NJ 07856 Tel. +1-973 770 7300 Fax +1-973 770 7302

Other Distributors:

Argentina · Australia · Austria · Belarus · Benin · Brazil · Bulgaria · Canada · Croatia · Czech Republic · Denmark · Egypt · Estonia · Finland · Ghana · Greece · Hong Kong · Hungary · India · Indonesia · Iran · Israel · Japan · Jordan · Korea · Kuwait · Latvia · Lebanon · Lithuania · Macedonia · Malaysia · New Zealand · Nigeria · Norway · Oman · Philippines · Poland · Portugal · Russia · Saudi Arabia · Singapore · Slovakia · Slovenia · South-Africa · Spain · Sweden · Syria · Taiwan · Thailand · Turkey · Ukraine · United Arab Emirates · USA · Vietnam · Yemen Our recommendations regarding our products are based on in-depth scientific testing in our Research Department; they are given in good faith, but no liability can be derived from them. It is the responsibility of the final product manufacturer to assure that claims made for the final product are in conformance with all applicable local laws. In other respect our Conditions of Sale and Supply apply.

Schülke & Mayr GmbH 22840 Norderstedt

Germany

Tel. +49 40 52100-0 Fax +49 40 52100-244 www.schuelke.com [email protected]

EN/Version 02.00/Revision Date: 28.05.2008/This product information is not automatically updated

Information

Microsoft Word - R1108634.rtf

2 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

25663