Read The PowerKEY CableCARD Module Installation Instructions text version

The PowerKEY CableCARD Module Installation Instructions

TM

®

Models PKM800 and PKM802

Your key to a new world of interactive digital entertainment and communications!

For installation in compatible TVs and home terminals. Not intended for use in a personal computer or a laptop, unless the device is specifically designated for such use.

Before You Begin

Before you install the PowerKEY CableCARD Module, record the two lines of alphanumeric characters that appear on the bottom left corner of the module, below the bar codes as shown in the example diagram. You may need to give this information to your cable service provider after you install the module.

Line 1: _______________________________

PKAAAABCD 001AA22B12B

Line 2: _______________________________

T12428

Important: You may or may not need to power on your host device (TV, home terminal, digital VCR, and so on) to install the module. Refer to the documentation that came with your host device before installing the module.

Installing the Module

1. To locate the appropriate slot in which to insert the module, refer to the documentation that came with your host device. Note: This diagram shows one of the Scientific Atlanta Explorer® Digital Home Communications Terminals. If you are installing the PowerKEY CableCARD Module in a different device, refer to the instructions that came with that device for specific information. 2. Follow the instructions that came with your host device to insert the module into the slot until it is firmly seated.

T12427

Important: There is physically only one direction to insert the module into the slot. When properly installed, part of the module may be visible outside the slot. You should feel the module "seat" when it is fully inserted. CAUTION: Do not try to force the module into the slot. Doing so could damage the module, the home terminal, or the TV. 1

3. After you insert the module, the module and host device IDs appear automatically on your TV screen, along with instructions and a telephone number to call. Note: If you do not see this information on the TV screen, the module may not be inserted properly. Try removing the module, then re-orienting and re-inserting it. If the problem persists, contact your service provider. Important: Do not remove the PowerKEY CableCARD Module after you install it. Removing the module may cause a temporary loss of your program services. 4. Record these IDs and the telephone number in the spaces below, and call your service provider as instructed. CableCARD ID: ____________________________________________________ Host ID: ___________________________________________________________ Telephone Number: _________________________________________________ Note: You may also need to give your service provider the alphanumeric information you recorded earlier in the Before You Begin section. 5. Refer to the documentation that came with your TV or host device for instructions on operating the TV or host device with the module.

If You Have Problems

· If you installed the PowerKEY CableCARD Module, and a code displays on the front panel of the host device, refer to the documentation that came with the host device for instructions. · If you installed the PowerKEY CableCARD Module in a TV and received an error message on the TV screen, refer to the documentation that came with the TV for instructions. · Contact your service provider if you continue to have problems.

2

FCC Compliance

United States FCC Compliance

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna, if applicable. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the cable company or an experienced radio/television technician for help. Any changes or modifications not expressly approved by Scientific-Atlanta, Inc., could void the user's authority to operate the equipment. The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the FCC and is intended to supply you with information regarding the FCC approval of this device. The phone numbers listed are for FCC-related questions only and not intended for questions regarding the connection or operation for this device. Please contact your cable service provider for any questions you may have regarding the operation or installation of this device.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) the device may not cause harmful interference, and 2) the device must accept any interference received, including interference that may cause undesired operation. PowerKEY® CableCARD Module Models PKM800 and PKM802 Manufactured by: Scientific-Atlanta, Inc. 5030 Sugarloaf Parkway Atlanta, Georgia 30042 USA Telephone: 770-236-1077

Canada EMI Regulation

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.

20060628FDC The PowerKEY CableCARD Module is protected by one or more of United States patent numbers 5003384, 5155590, 5235619, 5357276, 5420866, 5420923, 5440632, 5457701, 5481542, 5497187, 5684876, 5742677, 5870474, 5937067, 6157719, 6424717, 6510519, 6560340. Scientific Atlanta, Explorer, and PowerKEY are registered trademarks of Scientific-Atlanta, Inc. The PowerKEY logo is a trademark of Scientific-Atlanta, Inc. Cisco, Cisco Systems, and the Cisco Systems logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. CableCARD is a trademark of Cable Television Laboratories, Inc. All other trademarks shown are trademarks of their respective owners. Product and service availability subject to change without notice. © 2007 Scientific-Atlanta, Inc. All rights reserved.

Scientific-Atlanta, A Cisco Company 5030 Sugarloaf Parkway Box 465447 Lawrenceville, GA 30042 February 2007

Tel: 770.236.5000 www.scientificatlanta.com

Printed in United States of America

Part Number 745460 Rev A

Information

The PowerKEY CableCARD Module Installation Instructions

4 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

149325


You might also be interested in

BETA
The PowerKEY CableCARD Module Installation Instructions