Read Sign Components Manual (SAM) text version

SIGN COMPONENTS MANUAL (SAM)

For use by manufacturers covered under Underwriters Laboratories Inc.'s (UL) Listing and FollowUp Services for Electric Signs (UXYT/7) and Field-Assembled Skeletal Neon Sign and Outline Lighting Systems (UZBL/7), and for use by UL Representatives performing UL Follow-Up Service inspection. This Manual authorizes manufacturers to use certain UL Recognized Components, Classified Components and other non-Listed products*, when they are used under 1) the conditions expressed for the components in this Manual, 2) the installation instructions for the component, and 3) the requirements expressed in the Follow-Up Service Procedure, the associated Follow-Up and Inspection Instructions (FUII Pages) and the UL Standard for Electric Signs (UL 48). * Not covered by this manual, are non-Listed component materials that do not require additional authorization because requirements regarding their suitability and conditions of use are found in the UL Standard for Electric Signs (UL 48). Some examples are sheet metal, glass and thermoplastic diffusers (except those used to enclosure wiring and current-carrying parts). UL continuously updates this manual and makes the current version available via the Internet at www.ul.com/signs/manual. Updated versions of this manual are distributed periodically (approximately yearly), by mail, to all subscribers to UL's Listing Service and Follow-Up Services for Electric Signs (UXYT/7), Field-Assembled Skeletal Neon Sign and Outline Lighting Systems (UZBL/7), and subscribers to UL's Recognition Service and Follow-Up Services for Sign Accessories (UYMR2).

April 21, 2008 Edition Copyright 2008 Underwriters Laboratories Inc.

iiii

IMPORTANT INFORMATION FOR USERS OF THIS MANUAL Introduction

April 21, 2008

This document is issued by Underwriters Laboratories Inc. and is intended only to be used in conjunction with the Follow-Up Service Procedure and the UL Standard for Electric Signs, UL 48, by Manufacturers covered under UL's Follow-Up Services and by UL Representatives conducting UL Follow-Up Service Inspections. This Manual contains the names of companies authorized to use the Recognized Marking on or in connection with components which have been evaluated by UL and found to be in compliance with UL's requirements. These companies, as well as the manufacturers and submitters of the products, have entered into an Agreement with UL to use the Recognized Marking only on or in connection with products manufactured in compliance with UL's requirements. It should be noted that Recognized products of different makes or model designations are not necessarily equivalent in quality or performance. Where products are identified as being Recognized or Classified, the appearance of catalog or model numbers or other specific product designations in this Manual signifies, among other things, that: 1) representative samples of these products have been submitted to UL and found to comply with the applicable requirements, and that 2) the manufacturer has been authorized to use the Recognized Marking on production that continues to comply with UL's requirements and is subject to UL's Follow-Up Service. Manufacturers are not obligated to use the Recognized Marking on all of their production, and products which do not bear the Recognized Marking are not required by UL to comply with UL's requirements. Accordingly, the appearance of a company's name or a specific product designation in this Manual does not in itself assure that the products so specified or identified are subject to UL's Follow-Up Service. The manufacturer's products are not subject to UL's Follow-Up Service unless they bear the Recognized Marking. Only those products bearing the Recognized and Classification Marking should be considered as covered by UL's Recognition, Classification and Follow-Up Service. This Manual contains Component Recognitions in effect as of April 21, 2008. Records of Component Recognitions issued or withdrawn after this date will be found in UL's Listing Information database or historical records. In addition, Component Recognition's issued after this date will appear in future revisions of this Manual. Use of the Sign Components Manual UL's Follow-Up Service Procedure authorizes manufacturers covered under UL's Listing and Follow-Up Services for Electric Signs (UXYT/7), and Field-Assembled Skeletal Neon Sign and Outline Lighting Systems (UZBL/7) to apply the specified UL Listing Mark to products which comply with the requirements expressed in the Follow-Up Service Procedure, the associated Follow-Up and Inspection Instructions (FUII Pages) and the UL Standard for Electric Signs (UL 48). Compliance with these documents requires that manufacturers primarily use component products that are UL Listed. This Manual authorizes manufacturers to use certain UL Recognized Components, Classified Components and other nonListed products, when they are used under 1) the conditions expressed for the components in this Manual, 2) the installation instructions for the component, and 3) the requirements expressed in the documents noted above. This Manual is intended to assist manufacturers who may wish to use a Recognized Component or other non-Listed products in their UL Listed Electric Signs, Field Assembled Skeletal Neon Sign and Outline Lighting Systems. For all components, consult the Product Category Guide (General) Information preceding the individual component listings as well as the individual listings themselves for use conditions and ratings, as well as the required Recognized Marking.

ivi

IMPORTANT INFORMATION FOR USERS OF THIS MANUAL

April 21, 2008

This Manual provides the following: · authorization to use all components listed when the component is used according to the requirements of the Follow-Up Service Procedure, the UL Standard for Electric Signs, UL 48, the associated Follow-Up and Inspection Instructions (FUII Pages), and the specified limitations or conditions of use; names of companies which are authorized to provide components bearing a Recognized Marking as of the date noted in the introduction on page i; information about the form and nature of the Recognized Marking to be used by a specific manufacturer or for a specific class or category of product; information relating to limitations or conditions of use applying to the component;

· · ·

Component Recognitions are arranged alphabetically in this Manual by product category and, when included, individual Recognitions are arranged alphabetically by company name under each category. Products which are neither Listed nor Recognized by UL are grouped under the category titled "Miscellaneous" and identified by the initials MISC, and are arranged alphabetically by their common name. When individual Recognitions are not listed following the category title, refer to the UL's Recognized Component Directory for names of companies authorized to use the Recognized Marking and for components that are authorized to bear the Recognized Marking. The products are to be marked by Company name or UL File Number and catalog designation and, when Recognized for use in Canada, . Recognized Component Mark for Canada, When included, Product Category Guide (General) Information at the beginning of each product category, except MISC, provides important information regarding the scope and limitation of the Component Recognitions and a general description of the Recognized Marking authorized for Component Recognition in that category. Unless otherwise noted, the limitations and conditions of use provided in the Product Category Guide (General) Information are to be applied to all components having Recognition in that category. Some companies may be authorized to use a trade name or trademark for identification of Recognized Components in place of their company name, in such cases, refer to UL's Recognized Component Directory for a reproduction of the trade name or trademark. Products listed under the category identified by the initials MISC may be produced by any manufacturer. Such products are neither UL Listed nor Recognized by UL, and, UL in no way has established Agreements with the manufacturers of such products that may be used as a basis to insure their uniformity or performance. All components must be used for only the purpose intended by their manufacturer and as may be identified in this Manual, and under the conditions of use identified in this Manual. However, even when the conditions of use and all other applicable requirements are met, UL reserves the right to evaluate specific constructions incorporating these products and determine suitability.

1

FLEXIBLE METAL CONDUIT (DXUZ2)

1. Shall be used within a metal sign body and polymeric sign face. 2. Not to be relied upon for grounding or bonding.

GASKETS AND SEALS (JMLU2) & GASKET MATERIALS (JMST2)

1. Suitable for use in an outdoor sign as a weather seal, such as for a door or removable cover of a sign body or enclosure. 2. Adhesive alone is not suitable to secure a gasket unless the adhesive has been separately authorized for that application.

MISCELLANEOUS NON-RECOGNIZED DEVICES (MISC)

"Christmas Tree" Fasteners 1. Only suitable for use in indoor signs. 2. Only suitable to secure lightweight decorative parts or neon tube supports. Velcro 1. Only suitable for use in indoor signs. 2. Not suitable for completing an electrical enclosure. 3. Adhesive alone is not suitable to secure Velcro to non-flat surfaces when Velcro is used to secure parts weighing more than 4 lbs.

INSULATING BUSHINGS (NZMT2)

1. Suitable for use as mechanical protection of insulation on low-voltage wiring. 2. Suitable for use as low-voltage wiring strain relief. The strain relief test shall be conducted as described in UL48 Section 34 for each new unit design. The manufacturer shall keep a record of each test. The Field Representative shall witness the test.

NEON TRANSFORMERS & NEON POWER SUPPLIES (PWIK2, PWIK8)

This category covers neon transformers and power supplies for use with end products employing gas-filled glass tubing identified as neon or electric discharge tubing. CONDITIONS OF ACCEPTABILITY Each Recognized Component has Conditions of Acceptability that define the parameters of use for the component in an enduse product. Conditions of Acceptability are identified in the individual Recognitions by one or more letters appearing next to the model designation or catalog number under the heading "Conditions of Acceptability." The letters that appear identify which of the Conditions of Acceptability apply to the particular model or catalog number. Where the Conditions of Acceptability require testing or are unique to the component, the letters "TR" appear next to the model designation or catalog number under the heading "Conditions of Acceptability" and reference will need to be made to the individual Recognition Report. · A - Intended for use only in applications that comply with the requirements of the end product. · B - Suitable for use only indoors. · C - Suitable for use outdoors where protected from rain, snow and water spray. · D - Suitable for use only where the neon tubing between the neon supply electrode receptacles is either; a) one continuous length of tubing or b) multiple lengths of tubing interconnected only with Listed more than 1000 V lampholders (see OJOV) of the lamp-to-lamp type. Listed or Recognized Component Sign Accessories (UYMR/2) and Listed Gas Tube Sign and Ignition Cable (GTO Cable) (ZJQX) are not acceptable for interconnecting neon tubing lengths in any part of the secondary circuit. · E - Suitable for use only where contained in an end-use product compartment that is suitable as an electrical enclosure. · F - Suitable for use only where made inaccessible to contact by users during user maintenance while energized. · G - Provided with connection means suitable for factory wiring only; not for field wiring. · H - Not provided with a means of connection in accordance with NFPA 70, "National Electrical Code," therefore, suitable means needs to be provided in the end-use product. · TR - Requires testing or other evaluation in the end product; refer to individual Recognition Report. PRODUCT MARKINGS Transformers and power supplies covered under this category are marked "Indoors,""Outdoors,""Weatherproof" or "WP." Products marked "Indoors" are only suitable for use indoors, and products marked "Outdoors" are suitable for use indoors or outdoors sheltered from rain, snow and the like by being located within a sign body, enclosure and the like. Products marked "Weatherproof" or "WP" do not need to be additionally sheltered from rain, snow and the like. Transformers and power supplies covered under this category are marked with a Type number from 1 to 8 in association with the location designation

2

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

"Indoors,""Outdoors,""Weatherproof" or "WP." These Type numbers identify particular construction features associated with a particular transformer or power supply as identified below: · Type 1 - Open core-and-coil neon transformer or unenclosed neon power supply with body of the unit and input and output terminals or leads that should be enclosed in accordance with end-product requirements. · Type 2 - Neon supply with input and output terminals or leads that should be enclosed in accordance with end-product requirements. · Type 3 - Neon supply with input terminals or leads enclosed and intended for connection to a permanent wiring system, and with output terminals or leads that should be enclosed in accordance with end-product requirements. · Type 4 - Neon supply with input and output terminals or leads enclosed and intended for connection to a permanent wiring system. · Type 5 - Neon supply with input terminals or leads enclosed and intended for connection to a permanent wiring system and provided with integral receptacles for output connection. · Type 6 - Cord-connected neon supply provided with integral receptacles for output connection. · Type 7 - Cord-connected neon supply with output terminals or leads that should be enclosed in accordance with endproduct requirements. · Type 8 - Cord-connected neon supply with enclosed output terminals or leads.

ACTOWN-ELECTROCOIL INC. 2414 HIGHVIEW ST PO BOX 248 SPRING GROVE IL 60081

E104680

Transformers, Indoor Type 1 Applicable Conditions of Use - A, B, D, E, G. Cat. No. FG or FN followed by2030CEAX, 3020CCAX, 3030CCAX, 4015CCAX, 4025CCAX, 5010CEAX, 5020CCAX, 5030CAAX, 6025CBAX, 2520CECX, 3020CEAX, 3030CDAX, 4020CCAX, 4030CBAX, 5015CCAX, 5025CBAX, 6015CCAX, 6515CCAX, 3015CCAX, 3025CCAX, 3508CFAX, 4025CBCX, 5010CCAX, 5015CCCX, 5025CBCX, 6020CCAX, 6520CBAX. Transformers, Indoor Type 2 Applicable Conditions of Use - A.B. - Cat. No. FX-3008CGAA. Transformers, Outdoor Type 2 Applicable Conditions of Use - A.B - Cat. Nos. FG or FN- followed by -7525OAAX, -7525OABX, FG-1435SABA and FN1435SABA. Transformers, Outdoor Type 4 Applicable Conditions of Use ­ A - Cat. No. FG or FN. Transformers, Outdoor Type 5 Applicable Conditions of Use - A, C, D - Cat. No. FG- or FN- followed by: 3030PAAX, 3030PABX, 3030PCAX, 3030PCBX, 3030PGAX, 3030PGBX, 3030PAAX, 3030PABX, 3030PBAX, 3030PBBX, 3030PCAX, 3030PCBX, 3030PFAX, 3030PFBX, 3030PGAX, 3030PGBX, 3030PFAX, 3030PFBX, 3030PBAX, 3030PBBX, 3060PDAX, 3060PDBX, 3060PDAX, 3060PDBX, 4030PAAX, 4030PABX, 4030PGAX, 4030PCAX, 4030PCBX, 4030PBAX, 4030PBBX, 4030PAAX, 4030PABX, 4030PBAX, 4030PBBX, 4030PCAX, 4030PCBX, 4030PFAX, 4030PFBX, 4030PGAX, 4030PGBX, 4030PFAX, 4030PFBX, 4030PGBX, 4060PDAX, 4060PDBX, 4060PDAX, 4060PDBX, 5030PAAX, 5030PABX, 5030PBAX, 5030PBBX, 5030PCAX, 5030PCBX, 5030PAAX, 5030PABX, 5030PBAX, 5030PBBX, 5030PCAX, 5030PCBX, 5030PFAX, 5030PFBX, 5030PGAX, 5030PGBX, 5030PGAX, 5030PGBX, 5030PFAX, 5030PFBX, 5060PDAX, 5060PDBX, 5060PDAX, 5060PDBX, 6030PCAX, 6030PCBX, 6030PGBX, 6030PCAX, 6030PCBX, 6030PFAX, 6030PFBX, 6030PGAX, 6030PGBX, 6060PEAX, 6060PEBX, 6060PEAX, 6060PEBX, 6030OFAX, 6030PFBX, 7530PCAX, 7530PCBX, 7530PGAX, 7530PGBX, 7530PCAX, 7530PCBX, 7530PFAX, 7530PFBX, 7530PGAX, 7530PGBX, 7530PFAX, 7530PFBX,7560PEAX, 7560PEBX, 7560PEAX, 7560PEBX,9030PCAX, 9030PCBX, 9030PGAX, 9030PGBX, 9030PCAX, 9030PCBX, 9030PFAX, 9030PFBX, 9030PGAX, 9030PGBX, 9060PEAX, 9060PEBX, 9030PFAX, 9030PFBX, 9060PEAX, 9060PEBX. Transformers, Indoor Type 7 Applicable Conditions of Use - A, C, G - Cat. No. FG or FN, FX-3008CGAB.

ALLANSON INTERNATIONAL INC. E39591 33 CRANFIELD RD TORONTO, ONTARIO CANADA M4B 3H2

Transformers, Outdoor Type 2 Applicable Conditions of Use - A.B - Cat. Nos. 330CI120, P330CI120, 330CI277, P330CI277, 330CI347, P330CI347, 430CI120, P430CI120, 430CI277, P430CI277, 430CI347, P430CI347, 530CI120, P530CI120, 530CI277, P530CI277, 530CI347, P530CI347, 630CI120, P630CI120, 630CI277, P630CI277, 630CI347, P630CI347. *May or may not be provided with a suffix "T". Transformers, Outdoor Type 5 Applicable Conditions of Use - A, C, D. Cat. Nos. 330EK120*, 330EK277*, 330EK347*, 330EKF120*, 330EKF277*, 330EKF347*, 430EK120*, 430EK277*, 430EK347*, 430EKF120*,

430EKF277*, 430EKF347*, 530EK120*, 530EK277*, 530EK347*, 530EKF120*, 530EKF277*, 530EKF347*, 630EK120, 630EK277, 630EK347, 630EKF120, 630EKF277, 630EKF347, 7530EK120, 7530EK277, 7530EK347, 7530EKF120, 7530EKF277, 7530EKF347, 930EK120, 930EK277, 930EK347, 930EKF120, 930EKF277, 930EKF347, 1030EK120, 1030EK277, 1030EK347, 1230EK120, 1230EK277, 1230EK347, P330EK120*, P330EK277*, P330EK347*, P330EKF120*, P330EKF277*, P330EKF347*, P430EK120*, P430EK277*, P430EK347*, P430EKF120*, P430EKF277*, P430EKF347*, P530EK120*, P530EK277*, P530EK347*, P530EKF120*, P530EKF277*, P530EKF347*, P630EK120, P630EK277, P630EK347, , P630EKF120, P630EKF277, P630EKF347, P7530EK120, P7530EK277, P7530EK347, P7530EKF120, P7530EKF277, P7530EKF347, P930EK120, P930EK277, P930EK347, P930EKF120, P930EKF277, P930EKF347, P1030EK120, P1030EK277, P1030EK347, P1230EK120, P1230EK277, P1230EK347, 960EK120, 960EK277, 960EK347, P960EK120, P960EK277, P960EK347, 960EKF120, 960EKF277, 960EKF347, P960EKF120, P960EKF277, P960EKF347, 7560EK277, 7560EK347, P7560EK120, P7560EK277, P7560EK347, 7560EKF277, P7560EKF120, 7560EKF277, P7560EKF347, 660EK120, 660EK277, 660EK347, P660EK120, P660EK277, P660EK347, 660EKF120, 660EKF277,

3

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

660EKF347, P660EKF120, P660EKF277, P660EKF347, 560EK120, 560EK347, P560EK120, P560EK277, P560EK347, 560EKF120, 560EKF347, P560EKF120, P560EKF277, P560EKF347, 460EK120, 460EK277, 460EK347, P460EK120, P460EK277, P460EK347, 460EKF120, 460EKF277, 460EKF347, P460EKF120, P460EKF277, P460EKF347, 360EK120, 360EK277, 360EK347, P360EK120, P360EK277, P360EK347, 360EKF120, 360EKF277, 360EKF347, P360EKF120, P360EKF277, P360EKF347, Mini330EK, Mini430EK, Mini530EK.

*-Indicates may or may not be provided with suffix "U". Power Supplies, Indoor Type 7 Applicable Conditions of Use - A, C, G. Cat. No. SS935B-18,Cat. No. 630FNI.

EVERBRITE INC. 4949 S 110th PO BOX 20020 GREENFIELD, WI 53220

E122656

Transformers, Outdoor Type 2 Applicable Conditions of Use - A.B - Models Series "NuAUX", Model 800-0174, 800-0175, 800-0176, 800-0177. Transformers, Outdoor Type 7. Applicable Conditions of Use - A, C, G - Models Series 2612, Model 800-0128.

FRANCE/SCOTT FETZER CO. 726 FAIRVIEW BLVD W PO BOX 300 FAIRVIEW TN 37062

E10092

Transformers, Outdoor Type 5 Applicable Conditions of Use - A, C, D. Cat. Nos. 3030 PBKMG 734, 4030 PBKMG 734, 5030 PBKMG 734, 3030 PBKMG 751, 4030 PBKMG 751, 5030 PBKMG 751, 4030 PBKMG, 4060 PBKMG, 5030 PBKMG, 5060 PBKMG, 6030 PBKMG, 6060 PBKMG, 7530 PBKMG, 4030PBKMG34, 4060PBKMG34, 5030PBKMG34, 5060PBKMG34, 6030PBKMG34, 6060PBKMG34, 7530PBKMG34, 7560PBKMG34, 9030PBKMG34, 9060PBKMG34, 7560 PBKMG, 9030 PBKMG, 9060 PBKMG, 12030 PBKMG, 12060 PBKMG ,15030 PBKMG, 15060 PBKMG, 6030, PBKMCG 51, 6060 PBKMCG 51, 7530 PBKMCG 51, 7560 PBKMCG 51, 9030 PBKMCG 51, 9060 PBKMCG 51, 4030PBKMCG34, 4060PBKMCG34, 5030PBKMCG34, 5060PBKMCG34, 6030PBKMCG24, 6060PBKMCG34, 7530PBKMCG24, 7560PBKMCG34, 9030PBKMCG34, 3030 PBKMAG 51, 4030 PBKMAG 51, 4060 PBKMAG 51, 5030 PBKMAG 51, 5060 PBKMAG 51, 5060 PBKMAG 51 277, 6030 PBKMAG 51, 6030 PBKMAG 51 277, 6060 PBKMAG 51, 6060 PBKMAG 51 277, 7530 PBKMAG 51, 7530 PBKMAG 51 277, 7560 PBKMAG 51, 7560 PBKMAG 51 277, 9030 PBKMAG 51, 9030 PBKMAG 51 277, 9060 PBKMAG 51, 9060 PBKMAG 51 277, 3030 PBKMG 51, 3030 PBKMG 51 277, 3060 PBKMG 51, 3060 PBKMG 51 277, 4030 PBKMG 51, 4030 PBKMG 51 277, 4060 PBKMG 51, 4060 PBKMG 51 277, 5030 PBKMG 51, 5030 PBKMG 51 277, 5060 PBKMG 51, 5060 PBKMG 51 277, 6030 PBKMG 51, 6030 PBKMG 51 277, 6060 PBKMG 51, 6060 PBKMG 51 277, 7530 PBKMG 51, 7530 PBKMG 51 277, 7560 PBKMG 51, 7560 PBKMG 51 277, 9030 PBKMG 51, 9030 PBKMG 51 277, 9060 PBKMG 51, 9060 PBKMG 51 277, 12030 PBKMG 51, 12030 PBKMG 51 277, 15030 PBKMG 51, 4030 PBKMCG 51, 4060 PBKMCG 51, 5030 PBKMCG 51, 5060 PBKMCG 51 Power Supplies, Outdoor Type 7 Applicable Conditions of Use - A, C, G. Model No. 6000FE1G-2, 6000-FS1G-2, 6000 FE1G-D2, 6000-FS1G-D2, 12000FE1G-D, 12000FS1G-D.

JINBO KECHUANG ELECTRONICS CO LTD 343 YANHE RD EAST XIANGZHOU ZHUHAI, GUANGDONG 519001 CHINA

E301540

Transformers, Indoor Type 7 Applicable Conditions of Use ­ B, G - Models JNB-0620A, JNB-9020A, JNB-1020A, JNB-1520A.

JOHNNY AUSTIN NEON CO 1119 BLUCHER ST CORPUS CHRISTI, TX 78401

E245558

Transformers, Indoor Type 7 Applicable Conditions of Use ­ B, G - Models JA 6000, JA 9000, JA 10000, JA 15000.

LECIP CORP 1260-2 KAMINOHO ITONUKI-CHO MOTOSU-GUN GIFU-KEN 501-0401

E188431

JAPAN

Transformers, Indoor or Outdoor Type 5 Applicable Conditions of Use - A, C, D -Model Nos. 4B09N3-08 , 4B75N3-08 , 4B06N3-08 , 4B05N3-08 , 4B05N3-11, 4B04N3-08 , 4B04N3-11, 4B03N3-08 , 4B03N3-11, 4B05N3-11, 7B09N3-08 , 7B75N3-08 , 7B06N3-08 , 7B05N3-08 , 7B04N308, 7B04N3-11, 7B03N3-08. 7B03N3-11, 4B09N6-H, 4B75N6-H, 4B06N6-H, 4B05N6-H, 7B09N6-H, 7B75N6-H, 7B06N6-H, 7B05N6-H, . Suffixes -08 may be replaces with suffix -H and suffix -11 may be replaced with suffix -M.

4

SIGN COMPONENTS MANUAL (SAM)

E203105

April 21, 2008

SUNLITE TECHNOLOGIES LTD 1005 HEWLETT CENTRE 54 HOY YUEN RD. KWUN TONG KOWLOON, HONG KONG

Transformers, Indoor and Outdoor Type 7 Applicable Conditions of Use - A, B, TR. Model Nos. HS6000, HS6000-D, HS6000-F, HS9000, HS9000-D, HS9000-F, HS 612-7.5kV RD, HS 612-7.5kV RF, HS 61210kV RD, HS 612-10kVRF 1. These power supplies are intended for use with the Zeon Corporation Power Supply Mounting Assembly, Model Hot Swap Mount Base.

TECHNOSERVICE S R L E210684 GALAZZANO ZONA INDUSTRIALE VIA GUARDIA DI ROCCA 37 SAN MARINO, ITALY

Transformers, Indoor and Outdoor Type 5 Applicable Conditions of Use - A, B, C, D. Model No. TR30150HOUS.

TRANSCO INC. 1059 COLITE DR WEST COLUMBIA SC

E190350

29170

Transformers, Outdoor Type 5 Applicable Conditions of Use - A, C, D. Models T312, T412, T512, T612, T5512 followed by PU, PB, PT, PK, PR, Models T312, T412, T512, T612, T327, T427, T527, T5527, T627, T5512 followed by PU, PB, PT, PK, PR, followed by final Suffix WD, Models T312PBG, T327PBG, T412PBG, T427PBG, T512PBG, T527PBG, T612PBG, T627PBG, T7512PBG, T7527PBG, T912PBG, T927PBG, T1212PBG, T1227PBG, T1512PBG, T1527PBG, S312PBG, S327PBG, S412PBG, S427PBG, S512PBG, S527PBG, S612PBG, S627PBG, S7512PBG, S7527PBG, S912PBG, S927PBG, S1212PBG, S1227PBG, S1512PBG, S1527PBG, T312PBGH, T412PBGH, T512PBGH, T612PBGH, T7512PBGH, T912PBGH, T1212PBGH and T1512PBGH.

TRANSFOTEC INTERNATIONAL LTD E145519 310 BLVD INDUSTRIEL ST EUSTACHE QC J7R 5R4 CANADA

Power Supply, Indoor, Type 7 Applicable Conditions of Use - A, C, G - Models Platinum-5000-20-SPT.

VENTEX TECHNOLOGY INC 7830 BYRON DR., SUITE 10 RIVIERA BEACH, FL 33404

E187585

Neon Power Supply, Indoor Type 7 Applicable Conditions of Use - A, C, G - Model VT9030-120C, VT9030D-120C, VT9030F-120C, "Y" Cord - Model WA0022, Accessory for use with Models VT9030-120C, VT9030D-120C, VT9030F-120C.

ZEON CORP 1500 CHERRY ST. LOUISVILLE, CO 80027

E217541

Transformers, Indoor and Outdoor Type 7 Applicable Conditions of Use - A, B, TR. Model No. Hot Swap Base. 1. Intended for use only in applications that comply with the requirements of the end product. 2. Suitable for use only indoors. 3. This assembly is intended for use in a portable sign as defined in UL 48. 4. This assembly is intended for use with a Recognized Component Sunlight Technologies Inc. neon power supply designated for use with the Hot Swap Base, with a maximum input rating of 120 V, 3 A and maximum output rating of 9 kV rms, 30 mA.

5

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

COMPONENT SIGNS (UXYT2)

CHICAGO SHOW INC. 1777 WINNETKA RD. NORTHFIELD, IL 60093

E52188

Fluorescent Sign, Cat. No. 5177. 1. This product is rated 120 volts and the total accumulated current rating of all ballasts in the sign is not to exceed 10 A. 2. This unit is intended only for installation on the Listed Models TJ-250 and TJ-300 (REMCOR) commercial food preparing machines (ice dispensers) only. 3. The suitability of the mounting and the loading (electrical and mechanical) this sign places on the end-use equipment, shall be determined. 4. Particular attention should be given to overheating of the internal wiring power supply cord, and switches located in the enduse equipment.

NEO-NEON INTERNATIONAL LTD. 13TH FL OF TOWER A NEW MANDARIN PLAZA 14 SCIENCE MUSEUM RD TSIM SHA TSUI, KOWLOON HONG KONG

E25328

Led Sign, Cat. No. "OPEN SIGN" 1. These products are only suitable for connection to a UL Listed or Recognized Class 2 or LPS Power supply with a continuous output of 24 Vdc. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 or LPS voltage and energy limited supplies. 3. These products rated to draw 4.17 Amps max each shall not exceed the output current and power rating of the power supply. 4. These products, when connected to a Class 2 or LPS Power supply with a continuous output of 24 Vdc, are suitable for installation in wet, damp and dry locations.

SIGNALEX INC. 5617 MCADAM RD MISSISSAUGA, ON L4Z 1N4 CANADA

E192550

Signs Face Frame, Cat. Nos. BSH-6250, BSH-1250, BSH-1500, BSH-2000, BSH-3000, BSH-1020 and filler/cabinets, BSHDW1-300, XP6000, BSHF-R-680, BSHD-R-8740, BSH-1100. 1. The thermoplastic sign face has not been investigated for use as an electrical enclosure. 2. The Exclusion of Water Test must be conducted on the end product. This test may be conducted with or without an adhesivebacked neoprene gasket which serves as a dust barrier. 3. All current-carrying parts and wiring connections within the sign compartment shall be suitably enclosed. 4. The suitability of internal wiring and connections should be evaluated in the end-use application. 5. Components that are employed in the end product should be evaluated with respect to suitability of construction, electrical rating, mounting and spacing of thermoplastic material from heat producing sources. 6. The end product must comply and be marked in ccordance with UL 48. 7. The end use product is intended to be permanently connected to the supply circuit, strain relief has not been evaluated in this investigation. 8. A suitable grounding connection complying with UL 48 should be made in the end product. The aluminum frame and steel siding shall be electrically bonded to the point of conduit connection (grounding means) to the sign. 9. The electric sign frame covered in this Report can be evaluated for water exclusion with or without the use of a neoprene gasket. The overall integrity of the sign cabinet shall be judged in the end product. The manufacturer's recommended assembly instructions should be followed to insure a reliable assembly.

CHANGING MESSAGE SIGNS (UYFS2, UYFS8)

A component is suitable for the end-use product, if the Conditions of Acceptability identified by the letters (A, B, C, etc.) next to the model designation or catalog number in the individual Recognitions. The following is a list of Conditions of Acceptability that may be applicable to each component covered under this category. A. Suitable for use outdoors when so designated and only where located to prevent rain, snow and the like from coming into direct contact as determined by the Water Exclusion Test in UL 48. B. Suitable for use only when contained in an end-product compartment that is a complete electrical enclosure. C. Suitable for use only when spaced from heat producing components at least: 1. One inch from transformers, ballast, high output fluorescent electrodes and electric discharge tubing; 2. Two inches from incandescent and HID lampholders; 3. Nine inches from incandescent and HID lamps rated 250 watts or less; and, 4. Twelve inches from incandescent and HID lamps rated 251-400 watts. D. Suitable for use only when made inaccessible to contact by users during user maintenance while energized. E. Not provided with supply and/or output connection means suitable for field wiring. F. These components are suitable for use with no spacing between themselves. Z. Refer to additional Conditions of Acceptability included in the individual Recognition report for this component.

6

SIGN COMPONENTS MANUAL (SAM)

E302683

April 21, 2008

CHAINZONE TECHNOLOGY CO LTD NANXIN YI RD GUICHENG NANHAI DISTRICT FOSHAN, GUANGDONG CHINA

Changing Message Sign Applicable Conditions of Use - A, B, E, Z - Models MO13, M016, MO18, MO20, MO25, MO32, MO40 may be followed xxx, where xxx may be replaced by any alphanumeric characters.

DAEHAN ULTRAVION CO. LTD. 596-3 JANG HANG-DONG, ILSAN-KU KOYANG-SHI KYONGGI-DO 411-834, KOREA

E205267

LED Changing Message Sign Modules Applicable Conditions of Use - E, Z - Cat. Nos. DE-320-UP, DW-320-UP, DW-160-UP, DW-160-UF, DW-500-UP.

FUTUREMEDIA DISPLAYS INC #800 2120 HUTTON DR CARROLLTON, TX 75006

E215616

Changing Message Sign Applicable Conditions of Use - A, B. Models FMD followed by 9, 12, 15, 18 or FMD24 may be followed by suffixes. Models FMTNNH-AAC-X-GG where "T" can be any letter, "NN" can be any number from 0 to 9, "H" can be blank or any alphanumeric character, "AA" can be any letter, "C" can be any letter, "X" can be blank, 3, 5, 7 or 9, and "GG" can be blank or any alphanumeric character.

IMAGINE SIGNS L L C 6006 SHULL ST BELL GARDENS, CA 90201

E253134

Changing Message Sign Applicable Conditions of Use ­ B, D, Z - Models XXYY Series, where XX may be any number between 12 to 26 incl. and YY may be any number between 06 to 13 incl.

MCKAY DATA SYSTEMS INC 16695 MARSCHALL RD. SHAKOPEE, MN 55379

E156815

Exterior LED Changine Message Module Applicable Conditions of Use - A, C - Cat. Nos. K4XXX-Y, K8XXX-Y, K13XXX-Y, K18XXX-Y where "X" may be any number 0 thru 9 and "Y" may be S or SD.

NEOVISION INC SUITE E 9365 WAPLES ST SAN DIEGO, CA 92121

E251621

LED Changine Message Sign Applicable Conditions of Use ­ Z - Cat. Nos. "NEO XX Series", where XX may be replaced by any letters of alphabet from A to Z incl. or numbers from 0 to 9 incl. or combination , Cat. Nos. "NEO XXX Series", where XX may be replaced by any letters of alphabet from A to Z incl. or numbers from 0 to 9 incl. or combination.

NEWTON TECHNOLOGIES INC SUNGSAN DISPLAY COMPLEX 68 GOBONG-RI SUNGSAN-MYUN GUNSAN-SI, JEONBUK REPUBLIC OF KOREA

LED Changine Message Sign Applicable Conditions of Use ­ Z - Cat. Nos. "LDP 2003MA, LDP3207MA Series & NTI2875S

E239061

OLSEN GAMING INC, DBA SPECTRONIX #440-348 1000 N GREENVALLEY PKY HENDERSON, NV 89074

E257157

Changing Message Sign Module Applicable Conditions of Use ­ Z - Cat. Nos. Model LED "Dot Matrix Display XX Series", where XX may be replaced by any letters of alphabet from A to Z or numbers from 0 to 9 or combination.

7

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

OPEN NV GELAAGSTRAAT 53 9150 RUPELMONDE BELGIUM

E243613

LED Display Unit Applicable Conditions of Use - A, C - Cat. Nos. Zephyr_04SSRU, Zephyr_04FSRU, Zephyr_04SDRU, Zephyr_04FDRU, Mistral_15SSRU, Mistral_15FSRU, Mistral_15SDRU, & Mistral_15FDRU with suffix "_wwww.hhhh.ddd".

OPTEC DISPLAYS INC 528 S 6TH AVE CITY OF INDUSTRY, CA 91746

LED Display Unit Applicable Conditions of Use ­ Z - Cat. No. 24VGABOXZZZZ2.1ZZZ

E204188

PALTRONICS INC 9246 TRINITY DR. LAKE IN THE HILLS, IL

E250835

60156

Changing Message Sign Main Power Supply, Contoller, Alternate Controller and Sign Display Applicable Conditions of Use ­ Z - Cat. Nos. SP320-5N-CASE-R1, CTRL580-IGT, CTRL580-PAL, & DP48X6-4 F.

SAMIK ELECTRONIC IND CO LTD. 419-3 CHEONGCHEON-DONG BUPYEONG-GU INCHON 403-030, KOREA

E249709

Changing Message Sign LED Matrix Module Applicable Conditions of Use ­ A, B, E, Z - Cat. Nos. SKM-F240.

STATIC CONTROLS CORP 30460 WIXON RD WIXOM, MI 48393

E318292

LED Changing Message Controller Sign Controller, Model AD-803CB and Modules Series AD-803PXXX where XXX is any alpha-numeric combination. Applicable Conditions of Use ­ A, B, D, F 1. Additional mechanical guarding of the fans shall be provided in the end use if the controller is installed on a dedicated circuit inside the sign that can be energized while the rest of the sign is de-energized. 2. Grounding leads are not provided on the LED Modules. The suitability of the mounting means shall be evaluated to additionally bond the Modules to ground in the end product. 3. The suitability of the mounting means shall be determined in the end use.

YOUNG ELECTRIC SIGN CO 5119 S CAMERON ST LAS VEGAS NV 89118

Changing Message Sign Module Applicable Conditions of Use ­ Z - Cat. No. Model Price Changer.

E176781

8

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

SIGN ACCESSORIES (UYMR2, UYMR8)

3M COMPANY COMMERCIAL GRAPHICS DIV 3M CENTER ST PAUL MN 55144

E65361

Flexible sign face material, Flexible sign face systems for use in electric signs designated 3MTM PanaflexTM Awning and Sign Facing 945 GPS, 946 GPS; 3MTM PanaflexTM Awning and Sign Facing 945GPS; 3MTM PanaflexTM Awning and Sign Facing 946 GPS with Built-in Color; 3MTM PanaflexTM Plus Awning & Sign Facing Series 3000, Series 4000, Series 4050 HG Pre-decorated products. 1. Suitable for use in outdoor signs. 2. Not suitable for use as an electrical enclosure. 3. Suitable for use with Recognized Component Securement and Tensioning systems. 4. Securement and tensioning systems shall reliably secure the face to the sign and pull the face taut in all directions. 5. Clamps, hooks, etc., individually attached to the Panaflex and sign cabinet shall be spaced around the sign perimeter at maximum 3 ft. intervals. Flexible sign face systems, designated 3M(TM) PANAGRAPHICS (TM) II Intermediate Flexible Substrate decorated with 3M(TM) Translucent Intermediate Graphic Film Series 1330 or 3M(TM) Opaque Intermediate Graphic Film Series 7025 or printed with 3M(TM) Piezo Ink Jet Series 2300 or 4000 1. The suitability of the Panagraphics II or III systems when used on an outdoor sign to prevent entrance of water shall be determined in the end application. 2. The suitability of the mounting of the clamps to the sign shall be determined. 3. The Panagraphic II or III sign systems shall comply with the external decorative face spacing requirements of UL 48. 4. The Panagraphics II or III systems has not been investigated for use as an electrical enclosure. 5. The suitability of secureness of each clamp used will be judged in the end application. 6. When the Panagraphics II or III materials are used in sections in excess of 6 feet, suitable internal bracing of the signs should be employed to provide the necessary mechanical support for the tensioned face and prevent the material from contacting arcing or heat sources. Flexible Sign Face systems 3M(TM) PANAGRAPHICS (TM) III Intermediate Flexible Substrate decorated with 3M(TM) Scotchcal Translucent Intermediate Film Series 3630, 3M(TM) Translucent Intermediate Graphic Film Series 1330, 3M(TM) Opaque Intermediate Graphic Film Series 7025 or 3M(TM) Scotchcal Opaque Film Series 30 or 3M(TM) Scotchcal Translucent Film Series 50 or printed with 3M(TM) Piezo Ink Jet Series 2300, 4000, 6300 or 68200. 1. The suitability of the Panagraphics II or III systems when used on an outdoor sign to prevent entrance of water shall be determined in the end application. 2. The suitability of the mounting of the clamps to the sign shall be determined. 3. The Panagraphic II or III sign systems shall comply with the external decorative face spacing requirements of UL 48. 4. The Panagraphics II or III systems has not been investigated for use as an electrical enclosure. 5. The suitability of secureness of each clamp used will be judged in the end application. 6. When the Panagraphics II or III materials are used in sections in excess of 6 feet, suitable internal bracing of the signs should be employed to provide the necessary mechanical support for the tensioned face and prevent the material from contacting arcing or heat sources. Flexible Sign Face systems Light enhancement film material, designated 3M(TM) Light Enhancement Film 3635-100. 1. The use of this reflector system shall be employed in applications wherein the limitations as set forth in Table A are not exceeded. 2. This system may be used for securement to any combination of surface listed in Table A, provided the use temperature is not higher than the lowest temperature rating of any element of the combination. 3. This system may be used for any illuminated product provided with high output fluorescent, fluorescent, compact fluorescent, and neon at zero clearance. 4. This system is also suitable for indoor and outdoor use within a housing where exposed to high humidity or occasional exposure to water. The minimum temperature rating is -35 C. 5. This system is suitable for application to clean, flat surfaces identified below. Other surfaces require further evaluation. 6. This material has been evaluated for adhesive compatibility, stability, and flammability (94HB). No electrical tests have been performed. The engineer must consider the need to investigate the part of other than the properties investigated, in accordance with the applicable UL end-product standard or requirements outlined in the Standard for Polymeric Materials - Use in Electrical Equipment Evaluation, UL 746C. 7. The suitability of the film for use when exposed to oil, chemicals, refrigerant, soaps, x-rays, ultraviolet light and the like has not been determined by this investigation. TABLE A Substrates Aluminum painted with acrylic paint Bare Aluminum Steel painted with acrylic paint Polycarbonate Acrylic Maximum Temperature Rating, C 90 90 90 90 90

Note - Polycarbonate and acrylic substrates additionally must have suitable temperature ratings for each application. Flexible sign face material, Decorative Sign Face Material, 3MTM Chrome Graphic Film, 3635-110. 1. The use of this decorative system shall be employed in applications wherein the limitations are set forth in this report. 2. This system may be used for securement to any combination of surface provided it is adhered outside the sign body.

9

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

3. For use inside a sign body, the material will have to be evaluated per Item 4 below. 4. This material has been not evaluated for adhesive compatibility, stability, and flammability (94HB). No electrical tests have been performed. The engineer must consider the need to investigate the part of other than the properties investigated, in accordance with the applicable UL end-product standard or requirements outlined in the Standard for Polymeric Materials Use in Electrical Equipment Evaluation, UL 746C. 5. The suitability of the film for use when exposed to oil, chemicals, refrigerant, soaps, x-rays, ultraviolet light and the like has not been determined by this investigation. Polymeric adhesive systems, electrical equipment, pressure-sensitive adhesive tapes, designated No. "3MTM VHBTM Acrylic Adhesive Transfer Tapes" or "3MTM VHBTM Double Coated Acrylic Foam Tapes", F-9460PC, F-9469PC, F-9473PC, 4611, 4615, 4646, 4655, 4905, 4910, 4914, 4919F, 4919P, 4920, 4922, 4926, 4930, 4936, 4936F, 4941, 4941F, 4945, 4946, 4947F, 4947P, 4950, 4956, 4956F, 4979F, 4991, 5925, 5952, 5962, 9460PC, 9469PC, and 9473PC. 1. The use of these adhesive systems shall be employed in applications wherein the limitations as set forth in Tables A through G are not exceeded. 2. These adhesive systems may be used for securement to any combination of surfaces listed in the following Tables, provided the use temperature is no higher than the lowest temperature rating of any element of the combination. 3. These systems are suitable where exposed to high humidity or occasional exposure to water. This would include construction of outdoor sign cabinets where the joint is not subject to standing water. The minimum temperature rating is 35°C (-31°F). 4. These systems are suitable for application to smooth, flat, clean surfaces. Application to textured or rough surfaces requires engineering evaluation. 5. The adhesive dynamic bond strength specified in the Tables includes a safety factor of four. When considering the use of any adhesive covered by this Report, the strength of the adhesive joint used to position parts shall be capable of withstanding the maximum force that might be applied to the joint in the end application. This is called the dynamic bond strength and includes wind loading. The minimum square inches of adhesive tape to use is determined by dividing the maximum dynamic load in pounds by the adhesive bond strength in the Tables to obtain. 6. The adhesive static bond strength is 0.25 pounds per square inch, which is the ability to support the dead weight of a sign panel. Where the total weight of the panel is supported by other mechanical means such as by a flange, lip, or channel, the static bond strength calculation is not applicable. The minimum square inches of adhesive tape to use is determined by dividing the maximum static load in pounds by 0.25 pounds per square inch. 7. After determining the amount of tape required in square inches for the static load and for the dynamic load, the largest number is the minimum amount of tape that shall be used. 8. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been performed. Additional evaluation is required for uses not specifically identified herein. 9. The suitability for use when exposed to oil, chemicals, refrigerant, soaps, X-rays, ultraviolet light and the like, has not been determined by this investigation. 10. The adhesive shall be applied in accordance with the manufacturer's instruction. All surfaces shall be clean and dry. The manufacturers instructions regarding cure time shall be followed. For Tables "NT" ­ Not Tested. TABLE A Bond Strength Lbs./inch2 10 10 7 10 10 10 8 10 Max Temp Rating, °C Adhesive Grade 5952 5925 5962 90 90 90 90 90 90 75 90 NT 90 NT 90 90 90 75 90

Substrate Acrylic Polycarbonate Cellulose Acetate Butyrate Aluminum Acrylic/Polyurethane paint Galvanized steel Rigid PVC Polyester paint

10

SIGN COMPONENTS MANUAL (SAM)

TABLE B Bond Strength Substrate Acrylonitrile-Butadiene-Styrene (ABS) Polycarbonate Phenolic Aluminum Galvanized Steel Stainless Steel Enameled Steel Unplasticized Polyvinyl Chloride (UPVC) Polyamide Type 6/6 (Nylon) Acrylic/Polyurethane Paint Polyester Paint Lbs./inch2 10 10 10 10 10 10 10 10 10 10 10 TABLE C Substrates Bond Strength Lbs./inch2 4914 Acrylonitrile-Butadiene-Styrene (ABS) Polycarbonate (PC) Aluminum Galvanized Steel Enameled Steel Stainless Steel Rigid Polyvinyl Chloride (PVC) Glass/Epoxy (Grade G-10, FR-4) Ceramic Polybutylene Terephthalate (PBT) Acrylic Acrylic/Polyurethane paint 10 10(8 for 4905 & & 4910) 10 10 10 10 10 10 10 10 10 TABLE D Substrates Bond Strength Maximum Temperature Rating, °C Adhesive Grades Lbs./ inch2 Acrylonitrile-Butadiene-Styrene (ABS) Polycarbonate (PC) Aluminum Galvanized Steel Enameled Steel Stainless Steel Nickel coated ABS Rigid Polyvinyl Chloride (PVC) Glass/Epoxy (Grade G-10, FR-4) Ceramic Polybutylene Terephthalate (PBT) Glass (with and without silane coating) Acrylic/Polyurethane paint Polyester paint 10 10 10 10 10 10 10 10 8 8 8 8 10 10 4919F, 4919P, 4926, 4936, 4936F, 4941, 4941F, 4956, 44956F, 4979F, 4946, 4947F, 4947P 75 90 90 90 90 90 90 90 90 110 90 90 90 90 75 110 110 110 110 75 110 110 90 NT NT 75 110 110 110 110 75 110 110 90 90 NT 90 90 NT NT NT NT NT NT NT NT 90 10 75 Maximum Temperature Rating, °C Adhesive Grade 4920 4930 4950 75 4905 4910 NT Max. Temp Rating, °C Adhesive Grade 4922 90 90 110 110 110 NT 110 75 90 NT NT 4945 90 90 110 110 110 90 110 75 90 90 90

April 21, 2008

4991 NT 90 90 NT NT NT NT NT NT NT NT NT 90 90

11

SIGN COMPONENTS MANUAL (SAM)

TABLE E Substrate Stainless Steel Aluminum Galvanized Steel Glass (not silane coated) Glass/Epoxy - FR4 Phenolic Nylon Polycarbonate Acrylonitrile Butadiene Styrene - ABS PVC Rigid Bond Strength Lbs./inch2 10 10 10 10 10 10 10 10 10 10 TABLE F Substrate Acrylonitrile-Butadiene-Styrene (ABS) Polycarbonate (PC) Aluminum Galvanized Steel Enameled Steel Stainless Steel Polyvinyl Chloride (PVC) Glass/Epoxy (Grade G-10, FR-4) Polybutylene Terephthalate (PBT) Bond Strength Lbs./inch2 10 10 10 10 10 10 10 10 10 TABLE G Substrates Acrylonitrile-Butadiene- Styrene (ABS) Polycarbonate Phenolic Aluminum Galvanized Steel Enameled Steel Ceramics Nickel Plated Iron Stainless steel Glass/epoxy (G-10, FR-4) Rigid polyvinyl chloride (PVC) BondStrength Lbs./inch2 10 10 10 10 10 10 10 10 10 10 10 Maximum Temp. Rating, °C Adhesive Grades 9473PC, F-9473PC 90 90 110 110 90 110 110 NT 110 110 75 9460PC, F-9460PC 90 90 110 110 90 110 110 NT 110 110 75 Maximum Temperature Rating, °C Adhesive Grade 4615 75 90 110 110 110 110 75 110 90 Maximum Temperature Rating, °C Adhesive Grade 4611, 4646, 4655 110 110 110 110 110 110 90 90 75 75

April 21, 2008

9469PC, F-9469PC 90 90 110 110 90 110 110 110 110 110 75

Sign Flashers, Cat. Nos. Electronic Flasher Series FS116, FS116RC, FS126, -126RC, -127, -146, -146RC and -147 may be followed by any number up to three digits, may be followed by Suffix PC and any number between 1 and 10,000, inclusive. Types FS143, FS152, FS162 may be followed by any number up to three digits, may be followed by Suffix PC and any number between 1 and 10,000, inclusive. Type SF120A-3608 may be followed by Suffix PC and any number between 1 and 10,000, inclusive. Series FSU, followed by 1, followed by 0, followed by 0, followed by 0, 3, 4, or 5, may be followed by suffix PC and any number between 1 and 10,000 inclusive. 1. These components should be installed in accordance with the manufacturer's instructions.

ABB INC. E242275 LOW VOLTAGE PRODUCTS & SYSTEMS AUTOMATION TECHNOLOGY PRODUCTS DIV USA 8242 LOOP RD. PO BOX 1000 BALDWNSVILLE, NY 13027

12

2.

SIGN COMPONENTS MANUAL (SAM)

These devices are to be used in accordance with the ratings and load types as specified below. Catalog Number (Input-Output) Operating Voltage Max Output Current (rms) FS126 120 V ac 1A FS146 24 V ac 1A FS127 120 V ac +2 A FS147 24 V ac +2 A FS143 24 V ac 3A

April 21, 2008

Type Load Incandescent Incandescent Incandescent Incandescent General Purpose Incandescent General Purpose FS152 120 V ac 3A Incandescent FS162 240 V ac 3A General Purpose, Incandescent FS116 240 V ac 1A Incandescent FS116RC 240 V ac 1A Incandescent S126RC 120 V ac 1A Pilot Duty FS146RC 24 V ac 1A Pilot Duty SF120A 120 V ac 1A Resistive Incandescent FSU1000 24 to 240 V ac 1 AF Steady 10 A Inrush Inductive Resistive FSU1003 24 to 240 V ac 6 A Steady 60 A Inrush Inductive Resistive FSU1004 24 to 240 V ac 10 A Steady 100 A Inrush Inductive Resistive FSU1005 24 to 240 V ac 20 A Steady 200 A Inrush Inductive Resistive Incandescent FS421 12/24 V ac 1A Resistive FS491 120/240 V ac 0.5 A Resistive Cat. Nos. may be followed by any number up to 3 digits, may be followed by suffix PC and any number between 1 and 10,000, inclusive. + - Output voltage to the load is half-wave rectified ac.

ABC SIGN PRODUCTS 2028 SE FRONTAGE RD FT COLLINS CO 80525

E80767

Lampholder adapter, Type LH. 1. This device is suitable for use in indoor or outdoor extruded aluminum awning frames. 2. This adapter is intended for use only with Listed, single or double contact, recessed lampholders (Cat. No. 530, Kulka) which snap-fit into, and are securely held by, the adapter. The lampholder shall be held securely with or without a lamp in place. 3. This adapter is intended to complete the enclosure housing of insulated live parts only. 4. This device shall be installed in an aluminum extrusion in accordance with the "Installation Instructions" supplied by the manufacturer in the smallest shipping container. Sign Face Tensioning System , Model ABC 1. The suitability of these tensioning systems in combination with any R/C (UYMR2) Flexible Sign Face Material to prevent entrance of water in outdoor sign applications shall be determined in the end product. 2. This product has not be evaluated for use as an electrical enclosure. 3. Tensioning clips shall be spaced as described in the Installation Instructions. 4. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provided with a means to prevent billowing. 5. The mounted assembly of sign face material in these tensioning systems shall comply with the electrical and thermal spacing requirements of UL 48. 6. These clips have been determined to be suitable with any R/C Flexible Sign Face Material of min. 0.020 inches (0.51mm) thick, suitability for use with a material of lesser thickness shall be determined in the end product.

ACTOWN-ELECTROCOIL INC. 2414 HIGHVIEW ST. PO BOX 248 SPRING GROVE, IL 60081

E240102

Class 2 LEDs, Cat. Nos. QRN90-15, QRW90-15, QAN90-15, QAW90-15, QGN90-24, QGW90-24, QBN90-24, QBW90-24, QWN90-24, QWW90-24, BRN90-15, BRW90-15, BAN90-15, BAW90-15, BGN90-24, BGW90-24, BBN90-24, BBW90-24, BWN90-24, BWW90-24. 1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component ­ Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply having continuous DC outputs rated as below in Item 3. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit. 4. The following identifies the rating to be used in calculating the maximum number of units per circuit. LED Cluster BRxxx-15, BAxxx-15 BWxxx-24, BGxxx-24, BBxxx-24 QRxxx-15, QAxxx-15 QWxxx-24, QGxxx-24 QBxxx-24 5. These products are suitable for use in dry, damp and wet locations. Load Max (ma) 35 mA 35 mA 35 mA 35 mA Watts 0.525 W 0.84 W 0.525 W 0.84 W

13

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

6. The weather enclosure does not require evaluation. LED Power Supply with Class 2 Outputs, Cat. Nos. LPS15-D1, LP24-D1, LPS12-D1. 1. This power supply has 1 output. The output has been evaluated and found to comply with Class 2 output requirements. 2. This power supply is provided with a metal enclosure that is suitable for use in dry, damp and locations. 3. The output of this power supply is rated 12 V DC, 4 amps, and 60 Watts or 24V DC, 2.5A, 60 Watts. 4. Each power supply shall be installed in accordance with the installation instructions. Class 2 LEDs, Bright Eyes (BEX24-12) BE, followed by: W, B, G, A or R, followed by: 24, followed by: 12; NextGen (ABCD-12) B or T, followed by: W, B, G, A or R, followed by: N or W, followed by: 90 or 110; and MiniMod MXW80-12 Series, where X can be A, B, G, R or W. 1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply having continuous DC outputs rated as below in Item 3. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit. The following identifies the rating to be used in calculating the maximum number of units per circuit. LED Cluster BEX24-12 ABC90-12 ABC110-12 Load Max (mAmps) 400mA per module pair 52mA 40mA Watts 4.8 W per module pair .62 W .48 W

Up to 90 LED clusters may be used when the LED's are ABC90-12. Up to 110 LED clusters are used when the LED's are ABC110-12. 4. These products are suitable for use in dry, damp and wet locations. 5. The weather enclosure does not require evaluation. LED Power Supply with Class 2 Outputs, Cat. Nos. LPS12-D4. 1. These power supplies have multiple outputs. The power supply has a maximum of four Class 2 outputs. The power supply has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 4. When not marked for indoor use only, all units shall be provided with liquid tight fittings on the primary and secondary circuits. Class 2 LEDs, Cat. Nos. Models SLR90-12, SLA90-12, SSR90-12, SSA90-12, SSG90-12, SSB90-12 and SSW90-12. 1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply having continuous DC outputs rated as below in Item 3. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit. The following identifies the rating to be used in calculating the maximum number of units per circuit. LED Cluster SLR90-12 SLA90-12 SSR90-12 SSA90-12 SSG90-12 SSB90-12 SSW90-12 Load Max (mAmps) 25mA 25mA 25mA 25mA 25mA 25mA 25mA Watts .3 W .3 W .3 W .3 W .3 W .3 W .3 W

Up to 200 LED clusters may be used when the LED's are SXX90-12. 4. These products are suitable for use in dry, damp and wet locations. 5. The weather enclosure does not require evaluation.

ADDICKS ENGINEERING & PRODUCT DEVELOPMENT CO. LTD. 6006 SHULL ST. BELL GARDENS, CA 90201

E250540

Class 2 LEDs, Cat. Nos. LED Module Pricer. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 Volt or less DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These Class 2, "LED Module Pricer" Series when connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations.

14

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

ADHESIVE ENGINEERING & SUPPLY INC. 15 BATCHELDER RD SEABROOK, NH 03874

E312156

Adhesives, Cat. Nos. S-300, S310, S350 1. The adhesive system may be used to secure any combination of surfaces described in Table 1. The maximum operating temperature for the combination shall not exceed the lowest temperature for the individual surface. 2. The adhesive system is suitable for securing smooth flat surfaces, unless another surface configuration has been noted. 3. The adhesive system has been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been performed. The engineer must consider the need to investigate the part for other that the properties investigated, in accordance with the applicable end-product requirements and / or requirements outlined in UL 746C, Standard for Material Used in Electrical Equipment Evaluations. 4. The suitability for the use when exposed to oil, chemicals, refrigent, soap, X-rays, ultraviolet light and the like has not been determined by this investigation, unless otherwise noted. 5. When considering the use of the adhesive system, One square inch of surface covered by adhesive can support in shear tension the weight specified in Table A. When determining the suitability of the adhesive system, the bond strength value should be based on the lowest average as-received bond strength value of the material combination. TABLE A Substrate Combination Aluminum to Polycarbonate Adhesive S-300, S310, S350 Max. Operating Temp. °C Lbs/in. 65 208.6

2

ADVANCE DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP O'HARE INTERNATIONAL CENTER 10275 W HIGGINS RD ROSEMONT, IL 60018

E220165

LED array drivers, Models GEXNPS30-120, LED120A0024V10D, LED120A0024V10F, LED120A0024V18F, LED120A0027V09F, LED120A0012V21F, LED120A1400C24F, LED120A0010V25F, LED120A0024V33F, LED120A0012V50F, GEXLPS21, OT50/120/10, 9137 007 07043, GEXLPS21-230V and 9137 006 073. 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. Cat. Nos. GEXLPS21-230V and LED277A0024V18F was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 60°C. 5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The drivers are intended for installation inside an electrical enclosure. 7. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. 8. The drivers are suitable for dry location use only except the drivers Models GEXNPS30-120, LED120A0024V33F, 9137 007 043, GEXLPS21-230V 9137 006 073LED120A0024V33F, LED120A0012V50F, GEXLPS21 and OT50/120/10 are suitable for damp location use. 9. The Model LED120A0024V10D has a Class 2, 0-10 V dc output for dimming purposes. Two output terminals are provided for connection to an optional dimmer control. LED array drivers, Models LED120A0700C24F, 9137 005 34302, LED120A0350C33F, LED120A0024V07F, LED120A0012V10F, LED120A0350C28FO, LED120A0700C24FO, and GEXNPS31-120. 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 25°C. except the Models LED120A0350C28FO, LED120A0700C24FO, and GEXNPS31-120 were tested for a 40C ambient. 4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an electrical enclosure or raceway. 5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The unit is intended for installation inside an electrical enclosure. 7. The Models LED120A0350C28FO and LED120A0700C24FO may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. LED array drivers, Models 9137 005 34302. 1. This component has been judged on the basis of a Class 2 Power Unit. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 25°C. 4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an electrical enclosure or raceway. 5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The unit is intended for installation inside an electrical enclosure.

15

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

LED array drivers, Model LEDINTA0024V41FO 1. This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an electrical enclosure or raceway. 5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The unit is intended for installation inside an electrical enclosure. 7. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. LED array drivers, Model LED120A0880C19FO and Dimming Driver Model LED120A0880C19DO . 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an electrical enclosure or raceway. 5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The unit is intended for installation inside an electrical enclosure. 7. The Model may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. 8. Model LED120A0880C19DO has a Class 2, 0-10 V dc output for dimming purposes. The two dimming output leads are gray and violet, provided for connection to a dimming controller. 9. The Dimmer Controller must be either a 100K Ohms Potentiometer or a standard 0-10V DC dimmer switch, which is not provided by the manufacturer. LED Dimmer, Models 9137 108 30902 1. This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 3. The unit is intended for installation inside an electrical enclosure. 4. This unit is provided with a Class 105(A) insulation system. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies. 5. The Xitanium Dimmer is only suitable for use in Class 2 circuits powered by Advance LED drivers with maximum input rating of 24Vdc, 4.1A, or 12VDC, 5A. Dimmer circuit is 0-10VDC. 6. This LED Dimmer Controller must be used with either a 100K Ohms Potentiometer or a standard 0-10 V DC dimmer switch. 7. For dry or damp location. Class 2 LED Light Strings,Series LSL followed by additional alphanumeric suffixes. 12NC - "Affinium LED Light Strings" part numbers are as follows: 929000116403, 929000116503, 929000116603, 29000116703, 929000116803, 929000050995, 929000050895, 929000110095, 929000145103, 929000149103, 929000149003, 29000148803, 929000148903. 1. These components are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 power source, rated 30V DC or less. 2. These components have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Strings when connected to a Class 2 source, are not to draw a total current or wattage of greater than the secondary or output rating of the Class 2 circuit. 4. These components are suitable for use in dry, damp and wet locations and are not required to be enclosed or protected from the weather in the end product, with supply sources rated at maximum output voltages ad follows: when connected to a Class 2, 30V DC max output supply for installation in a wet, damp or dry locations; or when connected to Class 2, 60 V DC maximum output supply for installation in a damp or dry location. Class 2 LED Array Drivers, Models No. LEDINT0024V41FO, GEPS24-100 1. This component has been judged on the basis of the required spacing in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40C. 4.This unit is provided with a Class 105(A) insulation system. A temperature test is required when the unit is installed within an electrical enclosure or raceway. 5. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 6. The unit is intended for installation inside an electrical enclosure. 7. The unit may be used within an electrical enclosure or raceway without temperature test provided they are mounted not closer than 1 in. end to end or 4 in. side to side from adjacent LED power supplies.

16 AGILIGHT INC. 1702 W AVE N SAN ANGELO, TX 76904

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

E255447

Class 2 LEDs, Cat. No. "SideWinder Series" may be followed by (Standard) or "SideWinder BL" may be followed by (Back Lit) or "ThinRayz Xtra" may be followed by (High Output) or "ThinRayz" - Cat Nos. AGI-SW1 Y XXX where Y and XXX can be any alphanumeric characters from 0 to 9 incl. and from A to Z incl.; "BrightStrip Series" - AGI-BS-6-X YYY where X and YYY can be any alphanumeric characters from 0 to 9 incl. and from A to Z incl. 1. These products are only suitable for connection to a UL Listed or Recognized maximum Class 2, 15 V AC, 30 V DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 circuit limits. 3. These Class 2 LED modules, are each rated max. 40 Watts per unit, LED moduleWhen units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp or wet locations. 5. These products are not required to be enclosed or protected from the weather. LED array drivers, Models AGI-LP1060-12-GG-240 1. These power supplies have a single output that complies with Class 2 output requirements. 2. These products are suitable for use in dry, damp and wet locations only. 3. The primary sides of these power supplies are suitable for connection with threaded type conduit only. 4. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 6. When not marked for indoor use only the power supply primary bracket shall be provided with min. 3.5 threads and tapered for connection to liquid tight conduit fitting. 7. When not marked for indoor use only, all models shall have liquid tight fittings on both primary and secondary circuits.

ALDOR ELECTRONIC SERVICES SUITE 212 2961 INDUSTRIAL RD LAS VEGAS NV 89109

E215454

Controller Board, Models PCB06PD, PCB32PD, and PCB64PD Driver Board, Models PCB10T4, PCB10T12, and PCB20T6 1. The controller and drivers covered by this report are suitable for damp and dry locations only. 2. The controller Models PCB64PD, PCB32PD, and PCB06PD are suitable for use on a 120 V, 60 Hz service and are capable of switching up to 64, 32, and 6 points, respectively. They are for use only with triac driver Models PCB20T6, PCB10T12, and PCB10T4. 3. The Model PCB20T6, 6 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a maximum load of 13 A, 1560 W. 4. The Model PCB12T10, 12 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a maximum load of 6.5 A, 780 W. 5. The Model PCB10T4, 4 point triac driver board is suitable for use with 120 V, 60 Hz service with each point rated for a maximum load of 6.5 A, 780 W. 6. The controller and drivers are intended to mounted on standoffs proving at least 1/2 in clearance between circuit boards and back of enclosure, within an aluminum enclosure of at least 0.020 inches thick, and an overall dimension provided with forced air ventilation as specified below. 7. The controller and drivers are intended to be mounted within an aluminum enclosure mounted in a vertical orientation having a minimum overall dimension that provides at least 4 inches from the unit to the top and side walls and 4 inches to other heat producing components and at least 2 inches clearance from printed wiring board mounted components and the enclosure cover. 8. The minimum cooling fan flow rate per driver board shall be at least 200 CFM. 9. The diameter of the fan opening and exhaust ventilation opening shall be at least the diameter of the fan blades. For each inlet fan opening there shall be an equivalent exhaust opening. Each opening is to be covered by louvers or other equivalent guarding to provide opening that comply with end product requirements. 10. The mounting of the controller and drivers and wiring between the controller and driver boards are to be factory assembled. Primary wiring to the controllers and output wiring to the loads from the driver boards can be made in the factory or field.

ALLANSON INTERNATIONAL INC. 33 CRANFIELD RD TORONTO, ONTARIO CANADA M4B 3H2

E251622

LED drivers Models ChromaLED Models CV14184 and CV125 power supplies and Class 2 LED Illumination Models ACLW -m R 2, ACLW-mG2, ACLW-mO2, ACLW-RGB, ACLW-WHO, ACLW-mCW2, ACLWmWW2, ACLW-mY2, ACLW-mB2. 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The output terminals are suitable for field wiring. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. Leakage current measurements shall be performed when more than four LED power supplies are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 5. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided.

17

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

6. The power supply is suitable for dry and damp. 7. If the power supply is mounted where wiring can contact the enclosure, the wiring shall be rated min. 75°C.

ALCAN COMPOSITES USA INC. 208 W 5TH ST PO BOX 507 BENTON KY 42025

E101623

Structural panels, designated ALUCOBOND or DIBOND. 1. These products do not comply with the electrical enclosure requirements and are intended as an outer decorative covering only. 2. "ALUCOBOND" panels shall be attached with screws, bolts or rivets and "DIBOND" panels shall be attached with bolts or rivets, to the structural framework. 3. Other than letter cut-outs and service covers, all designs shall be such as to minimize the amount of material edge that is exposed to the outside of the sign and no edge may be less than 2 in. from lampholder contacts. 4. Gasketing of permanently secured panels may be provided by the application of a hardening, outdoor caulking compound. 5. These panels are suitable for maximum 60 °C and should not be located within 2 inches of a heat producing component. 6. Mounting of heavy components such as ballasts, transformers, etc., shall be by machine screws which extend through all layers of the backing material, and nuts. For components weighing over 12 lbs., minimum No. 10 hardware shall be used. Structural panels, designated Sintra. 1. Light duty structural panels are materials intended to be cut for use as letter backs in electric signs. 2. The pane may be used as part of a sign body but shall not be relied upon as an electrical enclosure. 3. The panels shall not be used to support any wireway, ballast, or transformer. They may be used to support lightweight parts such as tube supports, lampholders and lamps. 4. Each letter shall have at least two points of support and shall have no point more than 10 in. from a point of support.

AMLIGHT LEDS 1824 S OLIVE AVE PO BOX 3411 ALHAMBRA, CA 9180

E248769

Class 2 LED Modules Models HLED-LMB-R, HLED-LMB-Y, HLED-LMA-G, HLED-LMA-B, HLED-LMA-WW, HLED-LMA-CW. ACLW -m R 2, ACLW-mG2, ACLW-mO2, ACLW-RGB, ACLW-WHO, ACLW-mCW2, ACLW-mWW2, ACLW-mY2, ACLW-mB2. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15V AC or Less and 30 volt DC or Less power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product. Class 2 LED Illumination Models 3LED-100X-R, 3LED-100X-Y, 3LED-100X-G, 3LED-100X-B, 3LED-100X-W, where R, Y, G, B and W stand for Red, Yellow, Green, Blue, and White Colors respectively. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit. Cat. No. 3LED-100X-R and -Y draw 15 ma per unit and 3LED100X-G, -B and -W draw 20 ma each. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather.

APM HEXSEAL CORP. 44 HONECK ST ENGLEWOOD NJ 07631

E210026

Toggle Switch Boots, Types N-1002, N1030, N1030 1/2-32, N5030, N5030L, N5030R, N5030S, IN-1030, IN1030 1/2-32, 1131/23, 1131/25, 1131/26, 1131/31, 1131/32, C1131/27, C1131/28, C1131/35, C1131/38, C1132/25 Push Button Boots, Types 1231/17, N5045, N5040G, 1231/32, N5040, N5040R, 1231/31, 1231/27, 1231/8, NC3030 7/16-32, N3030, N3030-2513, NC3030, NC3030-2513, NH3030, NH3030S, NC3030H, N3040 Rocker Boots, Types 1111/7, 1113/62, 1113/63, C1111/7, C1113/62, C1112/63, C1113/66, C1113/70, C1113/71, C1113/75 1. These devices are intended to be used in outdoor electric sign applications. 2. The ability of this product to prevent water from entering a switch needs to be evaluated in the end product. 3. The R/C (WOYR2) toggle switch for use with this boot shall comply with the following: a. The toggle (switch actuator) shall be rounded to prevent abrasion and cutting of the boot. b. The assembly shall be mounted on the bottom or side surface of a sign body only. 4. Unless the switch body is completely enclosed in a Listed weatherproof enclosure, drain openings in the bottom of the enclosure in which the switch is installed are to be provided in accordance with UL 48.

18

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

ARLON SIGNTECH LTD 4669 HWY 90 W SAN ANTONIO TX 78237

E80939

Flexible sign face systems for use in electric signs, designated "FLEXFACE", "FLEXFACE FX", "MPF" or "MPG" or "FLEXFACE PO", "FLEXFACE S & R" 1. Suitable for use in outdoor signs. 2. Not suitable for use as an electrical enclosure. 3. Sign face materials are suitable for use with all Recognized Component Securement and Tensioning systems.

ARTWARE AMERICA INC. 18102 PIONEER BLVD ARTESIA, CA 90701

E313732

Class 2 LED Modules (Clusters), Cat. Nos. AWL-4500C-A and AWL-2500C-A. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 12 V. 3. Class 2 LED Modules ("Cluster"), Cat. No.AWL-4500C-A and AWL-2500C-A are each rated max. 6 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Controllers Models Nos. AWL1200M, AWL1400M, AWL1800M. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 Volt dc or less power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These Class 2, low voltage, low energy LED controllers when connected to a Class 2 circuit, are not to draw a total wattage of greater than the secondary or output rating of the Class 2 circuit. 4. These products are suitable for use in dry and damp locations.

ASTRODYNE CORP SUITE 106 2760 LAKE SAHARA LAS VEGAS, NV 89117

E310222

Class 2 LED Power Supplies, Cat. Nos. SLD45-108V-XX, SLD45-110V-XX, SLD45-112V-XX, SLD45-115V-XX, SLD45-118VXX, SLD45-121V-XX, SLD45-124V-XX, SLD60-112V-XX, SLD60-115V-XX, SLD60-118V-XX, SLD60-121V-XX, SLD60-124V-XX. 1. These power supplies have a single output that complies with Class 2 output requirements. 2. Power supply, Model series ­FC and ­FE are suitable for use in dry, damp, and wet locations. Model series -FT is suitable for indoor use. Model series ­FT is suitable for wet and damp location when provided with a UL Listed NEMA Type 3 enclosure. 3. Power Supply, Model series ­FC and ­FE are provided with aluminum enclosure that complies with enclosure requirements. 4. Power supply, Model series ­FT shall be provided with a suitable enclosure to cover terminals. 5. Each power supply shall be installed in accordance with the installation instructions. Class 2 LED Illumination Module, Models Model ALD60-xyyz-FC Series, where x can be 1 or 2; yy can be 05, 06, 08, 10, 12, 15, 18, 21, 24 or 48 and z can be C, D, E or F. 1. These power supplies have a maximum of two Class 2 outputs. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. Power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings. 5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product. Class 2 LED Illumination Module, Model ALD120-xyyz-FC Series, where x can be 2; yy can be 08, 10, 12, 15, 18, 21, 24, 27, 36 or 48 and z can V. 1. These power supplies have maximum of two Class 2 outputs. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations, except models SLD120-236V-FC and SLD120-248V-FC are suitable for use in dry and damp locations due to output voltages above 30 V dc. 3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 4. When used in wet locations, each unit shall be provided with listed (QCRV) and CN 1/2 inch liquid tight conduit fittings.

19 ASTRUP CO 2937 W 25TH ST CLEVELAND OH

SIGN COMPONENTS MANUAL (SAM)

E125321

April 21, 2008

44113

Flexible sign face material, designated "Marquee", "Enlighten", "Premier", "Premier 2000" and "Reflections" with suffix numbers. 1. Suitable for outdoor use. 2. These products are not to be used as electrical enclosures. 3. These products are acceptable for use with all Recognized Component Sign Securement and Tensioning.

ATEX CO LTD HAKATAKINDAI BLDG, 7TH FL, 1-1-33 HAKATAEKIHIGASHI HAKATA-KU, FUKUOKA-SHI FUKUOKA-KEN 812-0013 JAPAN

E304657

Class 2, 12 15, 24 VDC, LED Strings Class 2 LED String Assembly, Series Designation FL10-VWXY-Z, SP10-VWXY-Z, CL10VWXY-Z, CH10-VWXY-Z. 1. For a portable indoor sign, these products are suitable for connection to a 12VDC, 0.5A, UL Listed Class 2 power supply. 2. For all types of signs, these products are suitable for use with a 12 VDC, R/C (UYMR2) Class 2 power supply. 3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 4. These products are suitable for use in dry, damp, and wet locations. 5. Lead wires do not have a voltage rating and are not R/C AVLV2 wiring. Lead wires must be separated from circuits of other voltages in the end application. 6. Each 96 LED rope is rated Class 2, 12 VDC, 0.5A. Class 2, 12 VDC Class 2 LED Module, LED Module: Series LM03-164AW5-0 1. For a portable indoor sign, these products are suitable for connection to a 12 VDC, 0.125 A, UL Listed Class 2 power supply, minimum. 2. For all types of signs, these products are suitable for use with a 12 VDC, R/C (UYMR2) Class 2 power supply. 3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 4. These products are suitable for use in dry, damp, and wet locations. 5. Lead wires do not have a voltage rating and are not R/C AVLV2 wiring. Lead wires must be separated from circuits of other voltages in the end application. 6. Each LED module is rated Class 2, 12 VDC, 0.125 A.

ATOFINA CHEMICALS INC, ATOGLAS DIV BLDG 14 900 1ST AVE PO BOX 61536 KING OF PRUSSIA PA 19406

E184104

Rigid sign face system, designated Tuffak XL in all colors. 1. Furnished in the form of sheets, with a minimum thickness of 0.093 in. (2.36 mm). 2. Suitable for use only as decorative material when remolded or reformed, or when used in thicknesses below the minimum. 3. Suitable for use as an electrical enclosure, however, only the non-UV coated side may be exposed to live parts. 4. Suitable for use in outdoor signs with the UV coated side on the exterior. 5. The mounting system must secure the sign face to the enclosure in such a way that the edges of the sign face are not exposed to the interior of the sign. This may be accomplished with channels, flanges or other suitable mechanical means. 6. These materials have a use temperature of 75 °C. If a heat producing Component such as electrode, transformer or ballast is located within 1 inch of the material, a temperature test should be conducted in the end product. 7. All materials have been investigated for the securement of conduit, electrode housings or the like. 8. The following markings or equivalent shall be provided where readily visible during servicing. a. "Do not attempt to repair or service a damaged sign face, cable support, or high-voltage splice insulator. For servicing of this sign, contact ____." (Blank to be replaced by Sign Company's name, City and State.) b. "Replace only with ______, Type ______." (Blanks to be replaced by Recognized Material Company's name and material Type or designation.) c. "DANGER ­ High Voltage - Disconnect Power Before Servicing." d. "Upon replacement of lamps, the electrode/GTO wire connection must be made mechanically secure by crimping or twisting, and wrapped with UL Listed thermoplastic tapes to a thickness equivalent to the GTO insulation." This marking shall be placed near the electrode/GTO connection. Marking - Company name and System designation is marked on protective film provided over surface of material such that a piece dimensioned 2 ft by 2 ft min. will contain all required markings. System designation will be the same as material designation except may be followed by additional digits. A marking indicating the side which is UV coated will be provided in the same dimensions as given above.

20

SIGN COMPONENTS MANUAL (SAM)

E258512

April 21, 2008

ATTO DISPLAY CO LTD. 1-207 PLANT GYEONGGI TECHNOPARK 1271-11 SA 1-DONG SANGNOK-GU ANSAN-SHI, KYONGGI-DO 426- 901 REPUBLIC OF KOREA

Class 2 LED Module, Cat. No. BFLX-YZ12 Series ("F-LED" Series), where X may be the numbers 100, 200, 300, 401, 403, 800 and 900, where Y may be the letters A or D, where Z may be R, G, B, Y or W and Class 2 LEDs: BFLK-FT Series ("F-LED" Series), where K may be 300 or 900; where F may be RGB and where T may be 5 or 12. 1. Class 2 LEDs, BFLX-YZ12 Series ("F-LED" Series): Each module is only suitable for connection to a Class 2 power source, rated 12 Volt or less. Model BFL300-YF5 is only suitable for connection to a calls 2 power source, rated 5 VDC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits. 3. Class 2 LEDs, BFLX-YZ12 Series ("F-LED" Series): Modules BFL100-YZ12 and BFL200-YZ12 are each rated max. 0.48 Watts per LED unit; modules BFL401-YZ12 and BFL403-YZ12 are each rated max. 0.96 Watts per LED unit; modules BFL800YZ12 is each rated max. 1.56 Watts per LED unit; modules BFL300-YF5 is each rated max. 0.45 Watts per LED unit; and modules BFL900-YF12 is each rated max. 1.08 Watts per LED unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 15 Volt AC or max. 30 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

AXIOM POWER CORP 8F-1 14 DENGKUNG RD TAIPEI, TAIWAN

E309404

LED Module, Cat. No. AX-LEY Series, where Y can be replaced with any numbers from 1 through 9. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits. 3. Class 2 LEDs designated AX-LEY series are each rated max. 7.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

BISRO CO LTD POST-BI CENTER 3RE FL 932 WONKOG-DONG DANWON-GU ANSAN-SI, GYEONGGI-DO REPUBLIC OF KOREA

E311706

LED back light string, Cat. No. BMLO-04 and BMLO-06 with letter suffix. 1. The LEDs were evaluated for connection to a UL Recognized Component Sign Accessory - UYMR2, Class 2, 12 VDC maximum output power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limiting requirements. 3. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 4. Units provided with UYMR2, 3M type VHB double-sided adhesive tape. Tape must be utilized per the UYMR2 "Conditions of Use" as defined in the Sign Components Manual.

BLUEVIEW ELECTRONICS OPTIC TECHNOLOGY CO LTD A7 JIAOLONG INDUSTRIAL ZONE CHENGDU, SICHUAN 610091 CHINA

E318168

LED Lighting Modules, BV-ALUMINUM-PRIANHA Series. 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 power supply.

21

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

4. These products are suitable for use in dry, damp and wet locations without additional enclosures. Part No. Operating Voltage Current per module Watts per module Emitting color ( V DC ) ( mA ) (W) BV-Aluminum-Piranha-R BV-Aluminum- Piranha-Y BV-Aluminum- Piranha-A BV-Aluminum- Piranha-WW BV-Aluminum- Piranha-CW BV-Aluminum- Piranha-PW BV-Aluminum- Piranha-G BV-Aluminum- Piranha-B 12 12 12 12 12 12 12 12 40 30 30 40 40 40 40 40 0.48 0.36 0.36 0.48 0.48 0.48 0.48 0.48 Red Yellow Amber Warm White Cold White Pure White Green Blue

LED quantity (pc) 14 14 14 22 22 22 22 22

LED Lighting Modules,BV-STRIP-PIRANHA Series. 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 power supply. 4. These products are suitable for use in dry, damp and wet locations without additional enclosures. Part No. BV-Strip-Piranha-1*3-R BV-Strip-Piranha-1*3-Y BV-Strip-Piranha-1*3-A Operating Voltage ( VDC ) 12 12 12 Current per module Watts per module Emitting color ( mA ) (W) 40 30 30 20 20 20 20 20 0.48 0.36 0.36 0.24 0.24 0.24 0.24 0.24 Red Yellow Amber Warm White Cold White Pure White Green Blue LED quantity (pc) 13 13 13 13 13 13 13 13

BV-Strip-Piranha-1*3-WW 12 BV-Strip-Piranha-1*3-CW 12 BV-Strip-Piranha-1*3-PW 12 BV-Strip-Piranha-1*3-G BV-Strip-Piranha-1*3-B 12 12

LED Lighting Modules,BV-Flexibility-X-X Series, where X-X can be any alpha-numeric combination denoting LED color. 1. These products are only suitable for connection to the output of a UL Listed or R/C Class 2 Power Supply rated 12VDC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 power supply. 4. These products are suitable for use in dry, damp and wet locations without additional enclosures. Part No. BV-Flexibility- SMD 1-R BV-Flexibility- SMD 1-Y BV-Flexibility- SMD 1-B BV-Flexibility- SMD 1-G BV-Flexibility- SMD 1-W BV-Flexibility- SMD- 2-R BV-Flexibility- SMD- 2-Y BV-Flexibility- SMD- 2-B BV-Flexibility- SMD- 2-G BV-Flexibility- SMD- 2-W Operating Voltage ( V ) 12 12 12 12 12 12 12 12 12 12 Current per module Watts per module Emitting color ( mA ) (W) 100 100 100 100 100 200 200 200 200 200 1.2 1.2 1.2 1.2 1.2 2.4 2.4 2.4 2.4 2.4 Red Yellow Blue Green White Red Yellow Blue Green White Max. LED quantity per module (pc) 15 15 15 15 15 30 30 30 30 30

LED Lighting Modules, BV-POWER-X-0.5W, BV-POWER-X-1W. 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. These products are rated per the Table below. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 power supply. 4. These products are suitable for use in dry, damp and wet locations without additional enclosures. Part No. Operating Voltage Current per module Watts per module Emitting LED quantity color ( V DC ) ( mA ) (W) (pc) BV-Power-R-1W BV-Power-W-0.5W 12 12 350 180 1.0 0.5 Red White 1 1

22

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

BOCA FLASHER INC 552 NW 77TH ST BOCA RATON, FL 33487

E221730

LED Channel Letter Sign Kit, Cat. No. CCS100, CCD72, LS1001, LS1002, LS1061, LS1062, CCD36, LSS3001, LSS3061 and CCD180. 1. These products are only suitable for connection to a UL Listed Class 2, AC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. LEDs connected to a 12 Volt AC Class 2 power source are not required to be enclosed or protected from weather. LEDs connected to a 24 Volt AC Class 2 power source are limited to installation in a dry or damp location only. 4. Cat. No. CCD72 is rated for 12 watts per unit, Cat. No. CCS100 is rated for 4.8 watts per foot, Cat. No. LS1002 is rated at 6 Watts per foot, Cat. No. LS1001 is rated 3.6 Watts per foot and Cat. No. SM0006 is rated at 0.96 Watts per unit. 5. 5. The total number of feet of each type and inches for the inch unit are not to produce a total wattage of greater than 60 watts per Class 2 circuit. 6. Models CCS100, LS1001, and LS1002 are provided with a R/C wire connectors on the printed wiring board to increase the length of channel letters. No other cut across the board is permitted. Class 2 LED Channel Modules, Cat. No. ACXXXX Series and DLSXXXX Series where XXXX maybe be any numbers from 0000-9999 and LED modules Color Controllers, Cat. No. SLMCTL, RSBCTL, and CTM. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 Volt or less power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LEDs, "Channel Letter LED" Modules ACXXXX Series and DLSXXXX Series when connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 circuit. 4. These products are suitable for use in dry and damp locations. LED drivers, Cat. No. MR16_1-5WD-xxx ("1 to 5 LED Driver") where xxx may be replaced with 12A or 24D; LED Disk, Cat. Nos. 5X1WxLB-yyyy ("5 LED Disk"), 3X1WxLB-yyyy ("3 LED Disk") and 1X1WxLB-yyyy ("1 LED Disk") where yyyy may be replaced with numbers 0 through 9 or letters of alphabet A through Z or combination of letters or numbers; Class 2 HPLS Light Strip, Cat. No. HPFLSxx-Q\'-24y-zzzz, where Q may be replaced with the number 1, 2 or 3, xx and zzzz may be replaced with letters of alphabet A through Z or combination of letters or numbers. 1. Class 2 LED Drivers Model LED Drivers, cat. No. MR16_1-5WD-xxx and LED Disk, cat. nos. 5X1WxLB-yyyy, 3X1WxLByyyy, 1X1WxLB-yyyy are only suitable for connection to a maximum , max. 15 Volts AC or max. 24 Volts DC or less. 2. Class 2 HPLS Light Strips, cat. no. HPFLSxx-Q'-24y-zzzz are only suitable for connection to a maximum , max. 24 Volts AC or less. 3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 4. Class 2 Assemblies, Model LED Drivers, cat. No. MR16_1-5WD-xxx, LED Disk, cat. nos. 5X1WxLB-yyyy, 3X1WxLByyyy, 1X1WxLB-yyyy and HPLS Light Strips, cat. no. HPFLSxx-Q'-24y-zzzz is each rated max. 24 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 5. Class 2 LED Drivers Model LED Drivers, cat. No. MR16_1-5WD-xxx and LED Disk, cat. nos. 5X1WxLB-yyyy, 3X1WxLByyyy, 1X1WxLB-yyyy are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volt DC or less. 6. Class 2 HPLS Light Strips, cat. no. HPFLSxx-Q'-24y-zzzz are suitable for use in dry, damp locations with supply sources rated at 24 Volt AC. Class 2 Powered LED Modules, Cat. No. HPLS/HPFB Series (Border Light) and NFLS-HO-XXX Series (Border Light), where XXX can be replaced with any alphanumeric character. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED modules, HPLS/HPFB Series (Border Light)", is rated max. 45 Watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. Class 2 LED modules color controllers, Models SLMCTL, RSBCTL, CTM. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 Volt or less power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These class 2, low voltage, low energy LED module color controllers when connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 circuit. 4. These products are suitable for use in dry and damp locations. LED flasher Buffer Cards, Cat. No. LSDT33X_24, CCDST50_24, BFPS0001 1. These components are to be installed in accordance with the manufacturer's instructions. 2. These devices are rated as specified below. Catalog Number LSDST33X-24 CCXST50_24 BFPS001 3. 4. (Input-Output) Operating Voltage 24 V ac 24 V ac 24 V ac Max Output Current (rms) 2.5 A 2.5 A 2.5 A Type Load LED LED LED

An electrical enclosure needs to be provided in the end product. No tests have been conducted on these components and as such, end product testing should be considered.

23

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

Class 2 Powered LED Modules, Cat. Nos. BF-HPNLS-12A-XXX-QQQ-ZZZZ Series, where XXX and QQQ may be blank or replaced with alphanumeric characters and ZZZZ may be replaced with any number combinations from 0000 to 9999. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 15 V. 3. Class 2 LED modules, Cat. No. BF-HPNLS-12A-XXX-QQQ-ZZZZ Series are each rated max. 14 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product. Class 2 LED Regulator Model HPCCSD. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt dc or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 24 Vdc. 3. These products are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.

BOYER SIGNS & GRAPHICS INC 26191 BRUSH AVE EUCLID OH 44132

Raceways, Cat. Nos. BP8788, BP8789. 1. The mounting means of a channel letter or sign component to the raceway was not evaluated. 2. Acceptability of securement shall be determined in the end use. 3. Suitable for indoor and outdoor use, drain holes are required for outdoor use. 4. Mounting means of the back plate was not evaluated.

E213579

BRIGHT VIEW ELECTRONICS 5TH FL 192 LIEN CHEN RD CHUNG-HO, TAIPEI HSIEN 235 TAIWAN

E258492

LED Channel Letter Sign Kit, Cat. No. BVM-S3IN series, BVM-S3IN E series, BVM-S1FT series and BVM-SFPC5 series. 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply or a UL Listed or R/C Class 2 or LPS Power Supply rated 12 or 24 VAC or DC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit. 4. The LEDs, when connected to a 12V AC or DC Class 2 or LPS power supply, are suitable for installation in wet, damp and dry locations without any additional enclosure. The LEDs, when connected to a 24V AC or DC Class 2 or LPS power supply, are suitable for installation in damp or dry locations without any additional enclosure.

CHANNELUME/LET-R-EDGE 4206 MAIN ST P O BOX 3046 UNION GAP WA 98903

E55183

Structural Siding, Cat. No. Channelume or Let-R-Edge. 1. The siding shall be bonded at points of conduit connection. 2. When used outdoors, all internal sign components shall be suitable for outdoor use. Urethane Foam Elastomer Wood Coating, "Channelcoat 2". 1. This material shall not be used to enclose bare live parts or wiring. 2. The coating shall be applied in accordance with the supplied instructions. 3. The coating shall be applied to give a complete and uniform covering over the treated surfaces (0.008 in. minimum thickness). 4. The coating is acceptable for use in lieu of "asphalt-based paint" where required with metal-faced plywood panels.

CHENGDU SAIXING ELECTRIC SCIENCE & TECHNOLOGY CO LTD 92#, 2 BLK OF ONE-CIRCLE E RD CHENGDU, SICHUAN, CN

E317700

Class 2 Powered LED Modules, Cat. No. C-XXM Series, where XX may be replaced with 20, 40, 60 or 90; and M may be replaced with B, G, O, R, W, or Y. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 15 V. 3. Class 2 LED modules, Cat. no. C-XXM Series are each rated max. 0.96 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output ating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available.

24

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

CHIEF ENTERPRISES INC 922 N OAKLAWN AVE ELMHURST IL 60126

E242292

Metal Joiner System, LETTER LOK Series of clinchlok machines such as LETTER LOK 2000 in combination with one of the following dies inserts Part No. MP70001 or Part No. MP70002 with punch Part No. MP70010 is for use in joining painted or unpainted sheet aluminum. 1. Die insert Chief Enterprises Part No. MP70001 is suitable for joining painted or unpainted aluminum nominal 0.040 in. thick (0.034 in. thick minimum) into painted or unpainted aluminum nominal 0.040 in. thick (0.034 in. thick minimum). Minor diameter of button not including the tabs made by the material flowing past the die blades 0.285in maximum. 2. Die insert Chief Enterprises Part No. MP70001 is suitable for joining painted or unpainted aluminum nominal 0.040 in. thick (0.034 in. thick minimum) into painted or unpainted aluminum nominal 0.063 in. thick (0.056 in. thick minimum). Minor diameter of button not including the tabs made by the material flowing past the die blades 0.295in maximum. 3 Die insert Chief Enterprises Part No. MP70002 is suitable for joining painted or unpainted aluminum nominal 0.063 in. thick (0.056in. thick minimum) into painted or unpainted aluminum nominal 0.090in. thick (0.080in. thick minimum) or painted or unpainted aluminum nominal 0.063 in. thick(0.056in. thick minimum) to painted or unpainted aluminum nominal 0.063 in. thick (0.056in. thick minimum). Minor diameter of button not including the tabs made by the material flowing past the die blades 0.285in maximum. 4. Punch Chief Enterprises Part No. MP70010 for use with any of the above die inserts 5. Minimum spacing between clinches is 0.5 in. Maximum spacing between clinches is 4 in. 6. The tooling has been evaluated for joining only two pieces of aluminum, painted or unpainted. 7. Best results are when joining two pieces of aluminum having the same nominal thickness. Aluminum in the same thickness ranges described above may be joined provided the thicker piece forms the mushroom cap. 8. Total combined thickness of aluminum shall not exceed 0.15in. 9. The thicker material shall not be more than twice the thickness of the thinner material. 10. The depth of the die cup has a nominal thickness equal to both layers of aluminum. 11. Clinches shall be inspected before the next production step to verify that the minor diameter is greater than 0.24 in. and less than the values specified above. 12. Clinches shall be inspected before the next production step to verify that they are round, free of cracks on mushroom cap, and free of cracks inside joint cup. Double struck clinches are not acceptable. 13. The die, punches and LetterLok machines shall be serviced and maintained in accordance with the manufacturers instructions. 14. A service log by date shall be kept for each machine. Each punch and die change shall be noted. Each change in set up for material thickness shall be noted. Punch and die usage shall be monitored and the tools replaced at least in accordance with the manufacturers replacement instructions. 15. Assemblies with defective clinches shall be reworked by adding a like number of defect free clinches adjacent to each bad clinch. Instead of reworking, the assembly shall be scrapped.

COOLEY INC 50 ESTEN AVE P O BOX 939 PAWTUCKET RI

E97069

02860

Flexible sign face systems, designated "FIRST FACE", "FIRST FACE 4 in 1", "Cooley-Brite" (CB), "Cooley Brite II" (CBII), "Coolthane", "SM-42", "Rigid Cooley-Brite", "Marquee", "Enlighten", "Premier", "Premier 2000", "Reflections", "Reflections XL", "Cooley Brite Lite" (CBL) "Vynabrite" each with or without suffix numbers 1. Suitable for outdoor use. 2. These products are not to be used as electrical enclosures. 3. These products are acceptable for use with all Recognized Component Sign Securement and Tensioning. Flexible sign face systems, designated "5M Flexible Backlit Signface" with suffix numbers. 1. The suitability of these materials in combination with Signtech, Inc., Type FH, FC, Signalex Inc., or ABC Sign Products clamps, to prevent entrance of water in outdoor sign applications, shall be determined. 2. These sign face materials shall comply with the external decorative face requirements of UL 48, particularly the spacings. 3. These materials have not been investigated for use as an electrical enclosure. 4. The suitability of the "fit" of the face material and the "secureness" of the clamp mechanisms of the sign, will be judged in the end application. 5. These materials shall not have more than one side surface colored (pigmented) and shall be mounted only with the white surface adjacent to lampholders, ballasts and the like. 6. When these materials are used on signs with any dimensions (length or width) in spaces greater than 6 ft, suitable braces should be employed to prevent the material from billowing and creating short spacings to heat sources. 7. These flexible sheet materials have been found suitable for use with the Signtech, Inc. (+) tensioning system, the ABC Sign Products tensioning system (++) or Signalex Inc. tensioning system (+++) below. The combination is suitable for use in sign applications where Items 1 through 5 (above) have been considered. Mounting and tensioning instructions, which accompany the following clamps, should be used to ensure proper use of the 5M Flexible Backlit Signface.

25

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

DAESANG INC. 716 KWACHON OFCTL 1-14 BYULYANG-DONG KWACHON-SHI KYUNGKI-DO 427-040, KOREA

E2119632

Electroluminescent Inverter, Cat. Nos. CX-2003U 1. These units have been evaluated for use in dry locations only. 2. These units are intended for use with R/C (AVLV2) Style 10505 Appliance Wiring Material in a length no greater than 15 meters per channel on Inverter model CX-2003U with a 1 amp fuse. 3. Cord connected units are not intended for permanent mounting unless entire unit and cord are mounted within an electrical enclosure. 4. Surface of units may be exposed to a maximum operating temperature of 80ºC. 5. These units are to be enclosed within a suitable enclosure. 6. The output cable is rated maximum 60 °C and is to be protected against physical damage within a suitable enclosure. 7. The output cable is to be protected against exposure to direct sunlight.

DAKTRONICS INC 331 32ND AVE, PO BOX 5128 BROOKINGS, SD 57006

E230358

LED Driver, Part No. OA-1192-XXXX, where X may be any number 0 through 9. 1. The LED driver is intended for use in signs. 2. The LED driver is to be located in a dry or damp location within an overall metal electrical enclosure designated as suitable for use in dry, damp, or wet locations, as appropriate. 3. The LED driver is to be mounted on one vertical wall of the enclosure. 4. These products are required to be enclosed and protected from weather. 5. Digits (Daktronics, Part No. OP-1192-XXXX) per driver: Digit Size 16 Column Driver 8 Column Driver 5 in. 16 digits 8 digits 7 in. 16 digits 8 digits 10 in. 16 digits 8 digits 15 in. 16 digits 8 digits 18 in. 16 digits 8 digits 24 in. 16 digits 8 digits 30 in. 16 digits 8 digits 36 in. 8 digits 4 digits 42 in. 4 digits 2 digits 48 in. 4 digits 2 digits 6. The outputs of the driver may be wired with Class 2 wiring methods when the driver is installed in the same sign body or housing as the LED panel. 7. The drivers, when located remotely, have not been evaluated for Class 2 or LPS wiring methods. Class 1 wiring methods between the LED driver and LED panel should be used. LED Digit, Part No. OP-1192-XXXX. 1. These products are only suitable for connection to a UL Recognized Daktronics 24 V LED driver. 2. These products have not been evaluated to be suitable as an enclosure. 3. These products are suitable for use in dry or damp locations. 4. These products are required to be enclosed and protected from weather. 5. The LED may be part of the weather enclosure only if the LED is in the same enclosure (Sign body) as the LED module. LED module may be mounted in a metal panel with holes for the LED to protrude. LED Driver, Part Nos. OA-1150-XXXX and OA-1230-XXXX, where X may be any number 0 through 9. 1. These products are only suitable for connection to a UL Recognized Daktronics 16 V ac LED driver. 2. These products have not been evaluated to be suitable as an enclosure. 3. These products are suitable for use in dry locations. 4. These products are required to be enclosed and protected from weather. LED Digits, Part Nos. OA-1150-XXXX and OA-1230-XXXX, where X may be any number 0 through 9. 1. The LED driver is intended for use in signs. 2. The LED driver is to be located in an indoor dry location within an overall metal electrical enclosure designated as suitable for use in dry locations. 3. The LED driver is to be mounted on one vertical wall of the enclosure. 4. These products are required to be enclosed and protected from weather. 5. Digits (Daktronics, Part Nos. OP-1150-XXXX and OA-1230-XXXX) per driver: Digit Size 16 Column Driver 5 in. 7 in. 10 in. 15 in. 18 in. 24 in. 16 digits 16 digits 16 digits 16 digits 16 digits 16 digits 8 Column Driver 8 digits 8 digits 8 digits 8 digits 8 digits 8 digits 4 Column Driver 4 digits 4 digits 4 digits 4 digits 4 digits 4 digits

26

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

6. The drivers have not been evaluated for Class 2 or LPS wiring methods. Class 1 wiring methods between the LED driver and LED panel shall be used. Class 2 LED system: Cat. No. DE 34mm LED Matrix Panel. 1. The component shall be reliably mounted in the end-product. 2. A suitable enclosure (weather, electrical) shall be provided in the end-product. 3. The internal volume of the end-product enclosure shall not be less than 9000 cubic inches. 4. One 100 CFM exhaust fan shall be provided for each power supply in the end-product and each fan shall be wired to operate 100% of the time. 5. A suitable branch circuit protective device not exceeding 20 A shall be provided in the end-product. Gas Price Display Module: Part No. [email protected]@@@-X-Y-NA-Z, where @ may be any alphanumeric character, X may be 10, 13, 18 or 24 (LED digit size), Y may be R, G or A (LED color) and where Z may be DI or SF and Part No. 0A-1356-9XXX, where X may be any alphanumeric character. 1. These components are intended to be installed in a sign and shall be reliably mounted in the end-product. 2. A suitable branch circuit protective device not exceeding 20 A shall be provided in the end-product. 3. A suitable disconnect device shall be provided in the end-product. 4. Models [email protected]@@@-X-Y-NA-Z are suitable for use in outdoor signs and comply with the Water Exclusion Test. After installation, the Water Exclusion Test should be conducted on the overall end-product. 5. Part Nos. 0A-1356-9XXX are required to be installed in a suitable electrical and weather enclosure that protects all sides. 6. Drain holes are provided in the bottom of the enclosure. Internal wiring and other components of the end-product shall not be installed below these openings and the components shall be installed such that the drain holes are free from obstructions. 7. Any changes or additional components added by the end-product sign manufacturer require consideration of additional testing (Temperature, Input, etc.). 8. Any splices need to be made in an enclosure outside the equipment. 9. Any splices need to be made in an electrical enclosure outside the equipment. 10. When installed in a double sided configuration, a minium of 6 in. shall be provided between the rear of each Part Nos. 0A1356-9XXX module.

DECA L L C OFFICE #214 2870 PEACHTREE RD ATLANTA, GA 30305 USA

E228977

Class 2 LED system: Cat. No. DE followed by 2-6 followed by B, G, O, R, W or Y followed by additional numbers and or letters. 1. These LEDs must be connected to a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2, 12 Volt AC or DC, 5 A power source. 2. These LEDs have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. No more than 124 individual LEDs that are provided in the LED Colors (Orange, Red or Yellow) are to be interconnected together on one single Class 2 circuit. 4. No more than 200 individual LEDs that are provided in the LED Colors (Green, Blue or White) are to be interconnected together on one single Class 2 circuit. 5. These LEDs are suitable for use in dry, damp and wet locations. LED Sign SystemDesignated LED Sign System. 1. Four Class 2 power supply designated as Let-60 by Lightech Electronics Industries, Ltd. shall be mounted within an enclosure having dimensions measuring 6-1/2 by 4-1/4 by 4-1/4 in. (117 cubic in.) or larger. If more than the four transformers noted are utilized, then the enclosure shall be proportionately increased. 2. Loading of each of the transformers with the LED's shall not exceed 5 amps. 3. Enclosure for mounting Class 2 power supplies shall comply with UL 48 (i.e. corrosion protection, thickness, grounding means, mounting, fastening means) 4. All primary wiring must comply with UL 48. Strain Relief for primary wiring shall comply with UL 48. 5. Secondary wiring must be marked CL2 OR CL3 in accordance with Article 725 of the NEC. Class 1 wiring methods must be maintained within the enclosure when intermixing Class 2 secondary with primary wiring. Class 2 cable shall be insulated and marked having the same voltage rating or better as the primary wiring. If cable is not marked with the insulation voltage, then primary conductors and secondary cable must be permanently positioned to maintain at least 1/4 in. spacing between circuits or a physical barrier is provided to maintain separation of circuits. 6. Secondary cable must be protected by rubber grommet when extending through an enclosure. Also, Class 2 cable must be long enough to extend into channel letter enclosure. Splicing shall only be done within channel letter or enclosure. 7. Marking shall comply with UL 48. Additional markings: Output per circuit ­ volts and amps (12 v ,5 amps) and marked "Class 2" each circuit. Enclosure is marked for "Dry Location". Also, "Warning: Risk of electric shock or fire, do not connect outputs in series or parallel". 8. Installation instructions shall be provided mounting of transformer enclosure and wiring of LED system. Class 2 LED system: Cat. No. B1A Series, Model DE followed by 1 followed by A, AQ, B, C, G, R, or W followed by additional numbers and or letters. 1. These LEDs must be connected to a UL Listed or Recognized Component Sign Accessory - UYMR2/8, Class 2, 30 Volt DC maximum, 3 A maximum power source. 2. These LEDs have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. B1A LED assemblies draw 1 watt total per LED board. The total wattage drawn by all modules connected to a single Class 2 supply shall not exceed the rated capacity of the Class 2 supply. 4. These LEDs are suitable for use in dry, damp and wet locations.

27

SIGN COMPONENTS MANUAL (SAM)

E303831

April 21, 2008

DELTA ELECTRONICS INC 3 TUNG YUAN RD CHUNGLI INDUSTRIAL ZONE TAOYUAN, TAOYUAN HSIEN 320 TAIWAN

LED Class 2 Power Supplies , Cat. Nos. SDMV1260A, SDMV2480A, SDMV2460A, SDMV2420A and 9137006209. 1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp locations. 2. These power supply needs to be installed in an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110° C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location LED Class 2 Power Supplies , Cat. Nos. SDMV2420A and 9137 006 208. 1. Models SDMV2420A and 9137 006 208 are rated for a 100-240 Volts, 50/60 Hz, 25 Watt input and a 24 V DC, 0.83 amp, 20 Watt output. 2. These components are intended for use in dry location only when not potted. When potted, they are suitable for use in damp locations. 3. These power supplies need to be installed in an enclosure with a means for connection to conduit. 4. A Temperature Test is not required of the power supply when installed in an enclosure having dimensions greater than 13.5 by 6 by 4 inches. When installed in a smaller enclosure and a Temperature is required, the maximum temperature on the output transformer by thermocouple is 90°C. 5. The Class 2 output of these LED power supplies are acceptable for use in a damp and wet location. LED Class 2 Power Supplies Models Model 913710052466 or 913710052467. 1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp locations. 2. These power supply needs to be installed in an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110° C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location

DURALED LIGHTING TECHNOLOGIES CORP. 15273 ALTON PKWY, SUITE 200 IRVINE, CA 92618

E218780

LED Channel Letter Sign Kit, Cat. No. L63 followed by 01 or 21, followed by a suffix B, G, O, R, Y or W followed by -12 or -24. 1. These products are only suitable for connection to a UL Listed Class 2, AC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. LEDs connected to a 12 Volt AC Class 2 power source are not required to be enclosed or protected from weather. LEDs connected to a 24 Volt AC Class 2 power source are limited to installation in a dry or damp location only. 4. These products are provided with a break point in the printed wiring board to increase or decrease the length of channel letters. No other cut across the board is permitted. 5. A maximum of 32 feet can be connected to each Class 2 transformer. See details below. LED Color LED's / Foot Amps / Foot Amps / 32 Ft Rating O, R, Y 20 0.120 3.84 B, G, W 20 0.08 2.56 LED Outline Lighting Kit, Cat. No. B6001 followed by a suffix A, O or R followed by -12. 1. These products are only suitable for connection to a UL Class 2, AC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. If cutting is required, these product must only be cut by the manufacturer. No field cutting is permissible. 4. A maximum of 16 feet can be connected to each side of a Class 2 transformer.

EASTMAN CHEMICAL CO BLDG P1 137 REGIONAL PARK DR KINGSPORT, TN 37664

E251104

Rigid sign face material non-enclosure rated, designated "Sheet manufactured with Tritan GX100(f1)". 1. Acceptable for use in dry, damp and wet locations 2. Limited to only decorative, sign face, and sign body applications. The rigid sign face non-enclosure rated material is not suitable for use as an electrical enclosure. 3. Minimum 5 cm (2 in) spacing from heat producing components required. 4. Water exclusion must be determined in the end product. 5. Installation and securement of the material into or onto a sign is required. Marking - Company name and system designation is marked on protective film provided over surface of material such that a piece dimensioned 2 ft by 2 ft min. will contain all required markings. System designation will be the same as material designation except may be followed by additional digits.

28 EGL CO INC 100 INDUSTRIAL RD BERKLEY HEIGHTS NJ

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

E153777

07922

Tube Supports, Cat. Nos. 61409, 614110, 614112, 614113, 614115 ,614210, 614212, 614213, 61415. 1. Suitable only for the support of electric-discharge tubing. 2. Suitable for use in indoor and outdoor signs. 3. Shall not be used to support a weight greater than 1-1/4 lb.

ELECTRALED INC. SUITE 105 10950 72ND ST N LARGO, FL 33777

E232462

LED Channel Letter Lighting System, Cat. Nos. ELED followed by ­1, -2, -3, -4. 1. All LED's shall be mounted in a suitable enclosure and in accordance with UL 48. If used outdoors, LED's must be mounted in an outdoor enclosure per UL 48. 2. All wiring from transformers to LED's shall be in a suitable raceway for the application. 3. The LED's are intended to be powered by the transformers, XPTQ, Jefferson Electric with the associated fusing shown in the table below. The transformers are intended for Indoor or Outdoor Type 3R environmental rating. Model ELED Transformer Output volt ac Max. output Fuse Max. LED by PWB ft -1 216-1101-000 24 4 Amps 40 ft. -2 -3 -4 216-1111-000 216-1121-000 416-1121-000 24 24 6 Amps 10 Amps 60 ft. 100 ft.

24 10 Amps per parallel circuit 100 ft. per circuit. 216-1131-000 Max. 2 circuits 416-1131-000 4. Printed circuit boards with LED's are supplied in 2, 4, 6 or 12 in. lengths. 5. Fuse/fuseholders are wired to the secondary leads of the transformers within the transformers enclosures. 6. Enclosure surface to secure the standoffs for printed wiring boards shall be aluminum. 7. LED's may be powered by a UL Listed or Recognized, Class 2, 12 or 24 volt output power source. Suitable for use in indoor and dry locations. One 40 ft. run of circuit boards can be used per source. 5. The ELED-5 system is supplied with a Powertronix Corp. Model AA-036539-D, Class 2 transformer. The transformer shall be provided with a maximum 5 Amp LISTED fuse on the secondary output prior to the printed circuit boards. The ELED-5 system may consist of either: 20 feet maximum of red, yellow or orange LEDs OR 16 feet maximum of white, blue or green LEDs. The LEDs must be in an electrical enclosed as described in the previous Conditions of Use. The transformer shall be mounted in a suitable electrical enclosure in accordance with UL 48 having a minimum volume of 52.0 cubic inches. If used outdoors, the transformer must be mounted in an outdoor electrical enclosure per UL 48 having a minimum volume of 52.0 cubic inches. In the end-product, a replacement of fuse marking shall be supplied adjacent to the fuse indicating "Replace with same type and rating of protective device." LED Channel Letter Lighting System, Cat. Nos. ELED-5 or ­6. 1. ElectraLED ELED-5 and ELED-6 are intended for Dry, Damp and Wet Location use only when LED's are connected to a Class 2 circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. Wet Location use meaning no additional electrical enclosure or sign body is required for the LEDs. 2. ElectraLED ELED-5 and ELED-6 are intended for Dry and Damp Locations use only when LED's are connected to a Class 2 circuit operating at a potential greater than under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. If the LEDs are connected to a Class 2 circuit operating at a potential greater than under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC then a Sign Body per UL 48 must be maintained to house the LEDs. 3. ElectraLED ELED-5 and ELED-6 LED's may be powered by a UL Listed or Recognized Component Sign Accessory UYMR2, Class 2, output power source. See Conditions of Use No. 1 and No. 2 above for additional details regarding enclosure requirements. 4. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limiting requirements. 5. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 6. These products may be prewired and the conductors may be cut to length per the installation instructions provided with the product or the product may be provided with terminals. Printed circuit boards with LED's may be supplied in 2, 4, 6 or 12 in. lengths. 7. Enclosure surface to secure the standoffs for printed wiring boards shall be aluminum or as follows: 7A. Standoffs may be secured to acrylic UYMR2 Sign Accessory Rigid Sign Face Material or polycarbonate UYMR2 Sign Accessory Rigid Sign Face Material using QOQW2, 3M double sided tape designated 4950 provided enclosure has a minimum 30.0 cubic inches of volume per 12 inches of LED printed circuit boards. 8. The ELED-5 system may be supplied with a Powertronix Corp. Model AA-036539-D, Class 2 transformer. The transformer shall be provided with a maximum 5 Amp LISTED fuse on the secondary output prior to the printed circuit boards. The ELED-5 system may consist of either: 20 feet maximum of red, yellow or orange LEDs OR 16 feet maximum of white, blue or green LEDs. The LEDs must be mounted in a suitable sign body in accordance with UL 48 when the ELED-5 system with the Powertronix Corp. Model AA-036539-D transformer and 5 A fuse as described above is utilized. The transformer shall be mounted in a suitable electrical enclosure in accordance with UL 48 having a minimum volume of 52.0 cubic inches. If used outdoors, the transformer must be mounted in an outdoor electrical enclosure per UL 48 having a minimum volume of 52.0 cubic inches. In the end-product, a replacement of fuse marking shall be supplied adjacent to the fuse indicating "Replace with same type and rating of protective device."

29

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

9. The ELED-6 system may be supplied with a Lightech Model LET-60, Class 2 transformer. The loading of the transformer shall not exceed 5.0 amps. The ELED-6 system may consist of either: 20 feet maximum of red, yellow or orange LEDs OR 16 feet maximum of white, blue or green LEDs. 9A. The Lightech Model LET-60 transformer shall be mounted in a suitable electrical enclosure in accordance with UL 48 having a minimum volume of 117.0 cubic inches or larger for every four power supplies. If more than four utilized then the enclosure shall be proportionately increased. If used outdoors, the transformer must be mounted in an outdoor electrical enclosure per UL 48 having a minimum volume of 117.0 cubic inches or 9B. Secondary wiring must be marked CL2 OR CL3 in accordance with Article 725 of the NEC. Class 1 wiring methods must be maintained within the enclosure when intermixing Class 2 secondary with primary wiring. Class 2 cable shall be insulated and marked having the same voltage rating or better as the primary wiring. If cable is not marked with the insulation voltage, then primary conductors and secondary cable must be permanently positioned to maintain at least 1/4 in. spacing between circuits or a physical barrier is provided to maintain separation of circuits. 9C. Secondary cable must be protected by rubber grommet when extending through an enclosure. Also, Class 2 cable must be long enough to extend into channel letter enclosure. Splicing shall only be done within channel letter or enclosure. LED Channel Letter Lighting System, Cat. Nos. ElectraLED FLEXTM Series. Model ED12- followed by -RD, -RO, -AM, -TG, VG, -BG, -BL, -WW or ­CW. TM 1. ElectraLED FLEX LEDs are intended for Dry, Damp and Wet Location use only when LED's are connected to a Class 2 circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. Wet Location use meaning no additional electrical enclosure or sign body is required for the LEDs. TM 2. ElectraLED FLEX LEDs are intended for Dry and Damp Locations use only when LED's are connected to a Class 2 circuit operating at a potential greater than under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. If the LEDs are connected to a Class 2 circuit operating at a potential greater than under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC then a Sign Body per UL 48 must be maintained to house the LEDs. TM 3. ElectraLED FLEX LED's may be powered by a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2, output power source. See Conditions of Use No. 1 and No. 2 above for additional details regarding enclosure requirements. TM 4. ElectraLED FLEX LED's were evaluated for connection to a UL Listed or Recognized Component Sign Accessory TM UYMR2, Class 2, 12 V source. The ElectraLED FLEX module draws 0.317 amps, 3.66 Watts per individual module when TM supplied by 12 V. If the ElectraLED FLEX module is supplied by any other voltage an input test must be conducted in the end-product to ensure the products do not draw a total wattage greater than the secondary or output rating of the Class 2 power supply involved. 5. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limiting requirements. 6. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 7. These products are prewired and the conductors may be cut to length per the installation instructions provided with the product. TM 8. ElectraLED FLEX LED's may be powered by Powertronix Corp. Model AA-036539-D, Class 2 transformer. The transformer shall be provided with a maximum 5 Amp LISTED fuse on the secondary output prior to the printed circuit boards. The LEDs must be mounted in a suitable sign body in accordance with UL 48. The transformer shall be mounted in a suitable electrical enclosure in accordance with UL 48 having a minimum volume of 52.0 cubic inches. In the end-product, a replacement of fuse marking shall be supplied adjacent to the fuse indicating "Replace with same type and rating of protective device." TM 9. The ElectraLED FLEX LED's may be supplied by a Lightech Model LET-60, Class 2 transformer. The LET-60 transformer shall be mounted in a suitable electrical enclosure in accordance with UL 48 having a minimum volume of 117.0 cubic inches or larger for every four power supplies. If more than four power supplies are utilized then the enclosure shall be proportionately increased. If used outdoors, the transformer must be mounted in an outdoor electrical enclosure per UL 48 having a minimum volume of 117.0 cubic inches or larger for every four power supplies. If more than four power supplies are utilized then the enclosure shall be proportionately increased. LED Channel Letter Lighting System, Cat. Nos. ElectraLED FLEXTM Series. Model MiniFlex Series Cat. Nos. EM12 followed by an additional suffix denoting the color of the LED's 1. These products are only suitable for connection to a UL Listed Class 2, 12 Volt AC or DC power source, or any R/C Class 2, 12 Volt AC or DC power source listed in the SAM, that complies with the stated conditions. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. This Class 2 product, when connected to a Class 2 circuit, shall not draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. E-LITE TECHNOLOGIES INC. E175045

2285 RESERVOIR AVE. TRUMBULL, CT 06611

Electroluminescent lamp inverters, Cat. Nos. 5200, followed by 000, 001, 002, 200, 201, or 202, followed by ­91. 1. These units have been evaluated for use in dry locations only. 2. These units are intended for use with this applicant's Recognized electroluminescent lamp, designated "E-lume", in the size specified below: InverterModel No. Lamp Size sq/in. ±10% Output inductance (mH ±20%) Choke insul. Class Max. Fuse Rating (A) 5200-000-91 5200-001-91 5200-001-91 5200-002-91 5200-200-91 5200-201-91 5200-201-91 5200-202-91 1801-2200 1401-1800 1151-1400 260-1150 1801-2200 1401-1800 1151-1400 260-1150 210 275 400 500 210 275 400 500 180 (H) 130 (B) 130 (B) 130 (B) 180 (H) 130 (B) 130 (B) 130 (B) 1.0 0.63 0.63 0.5 0.5 0.315 0.315 0.25

30

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

3. Cord connected units are not intended for permanent electrical enclosure. 4. Surface of units may attain a max. operating temp. of 80ºC. Electroluminescent panel base material, Cat. Nos. E-Lume and/or Flatlite. 1. The suitability of this material for use within an electrical sign shall be determined. 2. The suitability of the electrical contacts, with regards to clearance, insulation and lead pull shall be determined in the endproduct. 3. Samples of the lamp material were subjected to the Humidity Conditioning Test in UL 924, with acceptable results.

ELECTROBITS SIGN SYSTEMS INC SUITE 100 286 W ST-PAUL ST MONTREAL QC CANADA H2Y 2A4

E129837

Polymeric neon electrode enclosures, Model ECOT. 1. Maximum 3000 V to ground. 2. Must be inside enclosure. 3. Must be used only on cord-connected signs. 4. GTO cable entering boot must be rated minimum 105 ºC. Polymeric neon electrode enclosures , Model 3630. 1. These electrode insulators are for use only inside the sign body of indoor cord-connected signs over 6 mm dia. tube. 2. The securement method shall be described in the final application. 3. The electrode insulator shall not be used at voltages exceeding its rating. 4. The insulator shall be completely covered by Listed (UYMR) designation 3730 GTO Cable sleeving by Electrobits. High voltage, IN-LINE SPLICE, Model ILS1000. 1. This product is intended to house a GTO wire to GTO wire splice. 2. Maximum 6.0 KV, ac to ground. 3. For use only where protected from rain, etc. This component is not to be located closer than 1 inch from a heat producing component such as an electric discharge or transformer. Tube support pad, Model NTSP followed by BLK, GRY or WHT. A tie wire shall be used to secure the neon tube and tube support pad to the mounting surface. Tube support spacer pad, Model NTS. 1. The spacer provides ¼ inch spacing from neon tube to mounting surface when installed in accordance with manufacturer's instructions. 2. The spacer's material is suitable for use in damp locations. 3. The spacer is for use only on nonmetallic surfaces away from metal ground plane. 4. The spacer is not suitable for use as neon tube support. 5. Tie wire used for securement is 24AWG min. copper or nickel-plated copper. Splice Insulator, Model ILS2000 1. The splice insulator is for use with either indoor or outdoor signs. 2. The splice insulator shall be enclosed within an electrical enclosure. 3. Splice insulator may be used within three inches of a transformer enclosure. 4. The insulated portion of the transformer leads shall extend at least 5 in. (127 mm) from potting or transformer enclosure. 5. The splice insulator is rated 105 °C when used with 105° C rated GTO Cable. 6. The splice insulator shall be used with Electrobits Listed GTO Cable sleeving Cat. No. 3730 and may have zero clearance to grounded metal. Switch Box, Cat. No. DS-101, DS-102, DS-103, DS-104. 1. Must be inside an electrical enclosure in the end product. Toggle portion of switch may extend outside sign body for an indoor sign. For an outdoor sign, with toggle portion of switch outside enclosure, must use Cat. Nos. DS-103 and DS-104 provided with switch boot. 2. Switch box is not to be used as enclosure for supply connections. 3. Electrical connections to switch must be done at factory location. 4. Switch box for use in indoor signs or within outdoor signs. 5. If a heat producing component such as electrode, transformer or ballast is located within 3 in. of the switch box, a temperature test should be conducted in the end product. Tube Support, Cat. No. TS921Y-X, TS-922Y-X where X and Y may be a number or letter. 1. Adjustable tube support are to be solvent bonded with Trichloromethane, Bichloromethane, or Methylene Chloride at a maximum height of 31.75 mm (1.25 in.) from base to the bottom of cradle. Residential Neon Boot, Cat. No. ECRO 1. The end cap is intended for installation and assembly at a manufacturing location and it is not for field assembly (when or after the sign has been installed). 2. Electrode leads are to be twisted. Crimp connectors are not to be applied. 3. Where GTO cable contacts the electrode of the neon tube, the GTO cable shall be rated 105°C. 4. The end cap is to be used in neon signs which are intended for dry or damp locations. 5. Spacings of end cap to metal per the following: a) 1/4 in. for transformer rated 5,000 V or less. b) 1/2 in. for transformer rated 10,000 V or less. Polymeric neon electrode enclosures , Model Short Sleeve, Models SS10mm30mA, SS12mm60mA, SS13mm60mA and SS15mm60mA; End Cap, Models EC10mm30mA, EC12mm60mA, EC13mm60mA, and EC15mm60mA; Integrally sleeved GTO Cable Adaptor, Model GTOCA260; GTO Cable Sleeving, Model 3760. 1. These devices are rated 7500 V ac to ground. May be used with 15K mid-point grounded transformer. 2. These products are suitable for use in dry or damp locations. 3. These products are required to be enclosed or protected from the weather.

31

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

4. These products are Classified, under the CCN (UYTA) in File E318241, for use with specific manufactures of Integral Sleeved GTO cables rated 105(C minimum when used with GTO Cable Sleeving Adapter GTOCA260. 5. As of the September 5, 2008 effective date of UL879, Eighth Edition, all Integral Sleeved GTO cables indicated as suitable for use with the neon electrode enclosures covered by this report shall have a temperature rating of 120(C minimum for dry locations and 135(C minimum for damp locations when used with GTO Cable Sleeving Adapter GTOCA260. 6. These products are only for use in Listed signs and Sections of signs. They are not suitable for field installed skeletal neon or outline lighting. 7. GTO Cable Sleeving Adaptor GTOCA260 is not for use with the Electrobits GTO Cable

ELECTRO-LUMINX LIGHTING CORP 1187 CALLE SUERTE CAMARILLO, CA 93012

E251824

Electroluminescent Lamps, Electroluminescent Power Supplies Models SD-250, SD-400. 1. These units have been evaluated for use only in indoor signs (dry locations). 2. When power supply cord and plug connected, the power supplies are suitable for use when enclosed in a portable sign that does not need to be grounded. 3. The power supplies have been judged on the basis of the required spacings in the Standard for Power Supplies other than Class 2, and CSA C22.2 No. 107.1 - General Use Power Supplies which would cover the components themselves if submitted for unrestricted Listing. 4. The EL panels shall be considered as uninsulated live parts operating at 300V when evaluating their mounting in the end use.

ELKAMET KUNSTSTOFFTECHNIK GMBH GEORG-KRAMER STRASSE 3 PO BOX 1263 35216 BIEDENKOPF FED REP GERMANY

E100102

Aluminum reinforced sign face trim, Type Elkamet Profiles. 1. These trim materials are used to secure a rigid thermoplastic sign face to an outdoor or indoor sign. 2. The ability of the trim to exclude water from contacting live parts needs to be evaluated in the end product. 3. Minimum No. 8 sheet metal screws need to be provided for securing the trim to the sign body. The maximum spacing between screws shall not exceed 18 in. and no fewer than four screws are to be used per face. 4. These products do not comply with enclosure requirements. 5. The sign trim face shall be "Continuous solvent or adhesive bonding" to secure the sign face and trim together in one of the following combinations: Sign Face (Generic Material) Solvent Sign Trim (Generic Material) Methyl Methacrylate (Acrylic) MethyleneChloride Cellulose Acetate Butyrate

EMERALIGHT 111 E 10TH AVE NORTH KANSAS CITY, MO 64116

E243993

Class 2 LED Boards, Cat. Nos. SnakeEye, SideWinder, DiamondBack, Trinity, T2, Glory I, Glory II, and PowerHouse. 1. The number and arrangement of the LED boards connected to a Class 2 power supply shall not exceed the output wattage/current rating of the power supply. Each LED board is rated as follows: Model SnakeEye SideWinder Trinity T2 Glory I Glory II PowerHouse 2. 3. V DC 12 12 12 12 12 12 12 Watt/ma usage for each color Wht 0.5/42 0.5/42 0.5/42 0.5/42 1.0/83 1.1/92 2.2/183 Blu 0.5/42 0.5/42 1.1/92 Grn Red 0.7/58 Amb 0.4/33 0.4/33 0.7/58 -

0.5/42 0.4/33 0.5/42 0.4/33

DiamondBack 12

1.1/92 -

4.

The LED boards are intended only for connection to the 12 VDC output of a Class 2 power supply. The LED boards are secured to the sign housing by tape. No further evaluation is required unless there are heat producing components or uninsulated electrical terminals or parts in the same compartment. Alternatively may be secured by screws in accordance with instructions. The sign housing of a permanently wired sign shall be grounded to the supply connection ground.

32 ENOCH CORP. 1050 S NEVADA AVE. PROVO, UT 84606

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

E235719

Class 2 LED Module, Cat. Nos. LED Strips 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather. LED Power Converter, Class 2, Cat. Nos. PS24. 1. These products are suitable for use in dry and damp location. In wet location Signs, these products are to be installed where protected from rain, snow and water spray by water shield or sign body. 2. These products are intended for use only connected to a Class 2 circuit power. 3. Each output of this product complies with Class 2 requirements.

ESCO INC 2020 4TH AVE SW PO BOX 1237 WATERTOWN SD

E65625

57201

Sign frames, Model Nos. 04 thru 42 , followed by 1, 2, 3 or 4, followed by 1 or 2, followed by 1, 2 or 3, followed by 1, 2, 3, 4 or 5, followed by 1, 2, 3, 4, 5, 6 or 7. 1. Suitable for use in outdoor signs.

ESTAR LIGHTING INC. 110 LOCUST RUN OCALA, FL 34472

E232467

Class 2 LEDs, Cat. Nos. Matrix 3 LED Module, Matrix 6 LED Module 1. These products are not required to be enclosed or protected from weather or protected from weather. 2. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 4. Class 2 LED, Matrix (3 LED module) is rated 0.6 Watts per unit, Matrix (6 LED module) is rated 1.2 Watts. 5. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply circuit. 6. These products are provided with interconnect cable and connectors on the printed wiring board for connection in series. 7. These products are suitable for use in dry, damp and wet locations.

EVERBRITE INC 4949 S 110TH ST PO BOX 20020 GREENFIELD WI

E131602

53220

LED Clock Module Component, Part No. MV1100. 1. The enclosure is suitable for cord-connected, indoor, signs. 2. The clock module must be spaced a min. of 2 in. from any heat sources. 3. The temperature test was conducted at 25C ambient for mounting on an open back sign. If enclosed in sign body with other heat producing parts, a temperature test is required. 4. The acceptability of the product in CUL signs shall be considered in the end product. 5. Not suitable for installation on C-UL marked signs without additional electrical enclosure rated, 5VA, if plastic, or metal. LED power supply; Cat. Nos. "LumiBox" Cat. Nos. MM12P1, MM12P2, MM12P3, MM12P4, MM15P1, MM15P2, MM15P3, MM15P4, MM24P1, MM24P2, MM24P3, MM24P4, MM27P1, MM27P2, MM27P3, MM27P4, MM48P1, MM48P2, MM48P3, MM48P4, MM00650P, MM00650P3, MM00688P, MM00688P3, MM00761P1, MM00761P2, MM00761P3, MM00761P4, MM00761P5, MM00778P06, MM00778P07, MM00778P08, MM00778P09, MM00778P10, MM00778P11, and MM00778P12. 1. LED power supply, see Ratings in table below for location. 2. Power supplies identified as Class 2 under ratings may be wired using Class 2 wiring methods. 3. Power supplies identified as Class 3 under ratings shall be wired with Class 3 wiring methods. The LED's must be installed in a suitable electrical enclosure.

33

Catalog MM12P1 MM12P2 MM12P3 MM12P4 MM15P1 MM15P2 MM15P3 MM15P4 MM24P1 MM24P2 MM24P3 MM24P4 MM27P1 MM27P2 MM27P3 MM27P4 MM48P1 MM48P2 MM48P3 MM48P4 MM00650P

SIGN COMPONENTS MANUAL (SAM)

Location Output Circuits Number and Class Volts Wet Wet Dry Dry Wet Wet Dry Dry Wet Wet Dry Dry Wet Wet Dry Dry Wet Wet Dry Dry Wet 1-Class 2 2-Class 2 1-Class 2 2-Class 2 1-Class 2 2-Class 2 1-Class 2 2-Class 2 1-Class 2 2-Class 2 1-Class 2 2-Class 2 1-Class 2 2-Class 2 1-Class 2 2-Class 2 1-Class 3 2-Class 3 1-Class 3 2-Class 3 1-Class 2 1-Class 2 1-Class 2 1-Class 3 1-Class 3 2-Class 3 3-Class 3 4-Class 3 5-Class 3 6-Class 3 7-Class 3 8-Class 3 9-Class 3 10-Class 3 11-Class 3 12-Class 3 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120+ 120 120 120 120 120 120 120 120 120 120 120 Input Amps .5 1.25 .5 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 0.55 0.66 0.55 0.66 0.15 0.30 0.45 0.60 0.75 0.90 1.05 1.20 1.35 1.50 1.65 1.80 Volts 12 12 12 12 15 15 15 15 24 24 24 24 27 27 27 27 48 48 48 48 15 12 15 12 33 33 33 33 33 33 33 33 33 33 33 33 DC Output Total Watts TotalAmps 60 150 60 150 75 150 75 150 75 150 75 150 150 150 150 150 150 150 150 150 60 60 60 60 15 30 45 60 75 90 105 120 135 150 165 180 4.5 9.0 4.5 9.0 4.5 9.0 4.5 9.0 3.0 6.0 3.0 6.0 2.5 5.0 2.5 5.0 1.5 3.0 1.5 3.0 3.5 4.5 3.5 4.5 0.375 0.75 1.125 1.5 1.875 2.25 2.625 3.0 3.375 3.75 4.125 4.5

April 21, 2008

MM00650P3 Dry MM00688P Wet

MM00688P3 Dry MM00761P1 Wet MM00761P2 Wet MM00761P3 Wet MM00761P4 Wet MM00761P5 Wet MM00778P06 Wet MM00778P07 Wet MM00778P08 Wet MM00778P09 Wet MM00778P10 Wet MM00778P11 Wet MM00778P12 Wet

EXCELLART SIGN PRODUCTS L L C 1654 S. LONE ELM RD OLATHE KS 66061

E152309

Frame system Frame system EC(+) followed by -4, -4R, -6, -6R, -7, -7R, -8, -8R, -9, -9R, -12 Hinged and Standard, -D/F Hinged and Standard, -IDS, -S/F Hinged and Standard, or EC-S/F Access System. Accessories for use with EC frame systems, frame, angle, hat section, 6 in. radius corner, 9 in. radius corner, Cat. Nos. EC-4, -7, -8, EC-IDS, EC-Xtra, FF, FF-2, H-1, H-1.5, LC, LF, RR, or RRC retainers, Cat. No. EC-12 frame retainer brace, Cat. No. EC-S/F access system, Cat. No. EC lamp raceway, Cat. No. EC raceway cover, Cat. No. EC lamp/ballast track, Cat. No. EC-IDS raceway, Cat. No. EC Flex System for standard frame, hinged frame, or retro fit, Cat. No. EC-T1, -T2 trim caps, or Cat. No. 1 1/2, 2 1/2, or H divider bars. Cat. Nos. F retainer, F hinged retainer, FF short retainer, EC-3.25 radius post, EC-3.25 rectangular post, EC-revel connector, EC-3.25 bleed frame, EC-8 in. radius quarter end, EC channel letter front, EC channel letter back, EC channel letter lid.

34

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

Frame system Excellart (++) followed by C, C-2, M-C, or MC-R, for use with retainers MC- Alternate M-C, ZF.188, ZF.250, ZF-1 1/2, ZF-2, ZFC2 1/2, or ZFC-3. Frame system Narrowline, Cat. Nos. EC-4RN frame, EC-4N frame, 1 in. radius corner connector and cap. (+) Frames, angles, and hat sections have the same catalog number as the frame system. Frames available in standard or hinged versions. (++) Frames available in smooth or ribbed versions. Expanda Frame Model AMB13920. Lamp Socket Raceway and Cover Models AMB990 and AMB991. 1. When installed in an outdoor wet location application, consideration shall be given to conducting the water exclusion test of UL 48. 2. The suitability of the components to serve as wireways and electrical enclosures shall be determined in the end use. 3. When installed in an outdoor wet location, the bottom of the cabinet system shall be provided with at least two drain holes in each inside recess, except for the wireway.

FEDERAL HEATH SIGN CO. L L C 4602 N AVE OCEANSIDE, CA 92056

E125271

Sign face Tensioning Systems, designated "KLICK-RAIL. 1. The suitability of the flexible sign face material and the "Klick-Rail" assembly when used on an outdoor sign to prevent the entrance of water, shall be determined in the end-use application. 2. The suitability of the mounting of this assembly to the end-use sign shall be determined. Considerations should be given to the reliable mounting of the assembly to the sign body. 3. This system together with the flexible face material shall comply with the external decorative face requirements of UL 48, particularly the clearances from heat-generating components to decorative plastic panels. 4. The suitability of secureness of the clamp and flexible material shall be judged in the end-use application. 5. The installation of this system in a sign shall conform with the instructions provided with this tensioning system. Class 2 Powered LED Modules, designated RVI Series 1. These products are only suitable for connection to a UL Listed or UL Recognized Class 2, DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Illumination, RVI Series is rated 20 W per 2.7 m length with yellow LEDs and 21 W per 2.7 m length with Red LEDs. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 W per Class 2 circuit. 4. These products are suitable for use in dry, damp locations. When the Class 2 output is 12 V or under, these products are suitable for wet locations. 5. These products are not required to be enclosed or protected from weather.

FIBERSTARS INC. SUITE D-2 32000 AURORA RD. SOLON, OH 44139

E194105

Fiberoptic Light Source, Cat. Nos. 1500A and 2000A. 1. The products covered by this report may not be provided with a complete enclosure. Suitability of the overall enclosure shall be determined in the end product investigation. 2 Suitability of the power supply connection means shall be determined in the end product investigation. 3. Spacings between units and units per volume shall be as specified in drawing. 4. Suitable for use only when live parts are made inaccessible to contact by users during user maintenance while energized. 5. Investigated for use in indoor dry or damp locations only when provided with a suitable enclosure. 6. Fiberoptic cable has not been evaluated for use in plenums.

35

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

FRANCE/SCOTT FETZER CO. 2268 FAIRVIEW BLVD. PO BOX 300 FAIRVIEW, TN 37062

E239418

HID Lamp Ballast Assemblies, Cat. Nos. SBIP-250, SBIP-400 Series. 1. These products are suitable for use in dry and damp location only. 2. For SBIP-250 series, no temperature test is required in a sign when the minimum spacing between the HID lamp and a polymeric material, between the HID lamp and adjacent ballast, or the HID lamp and other components is 7.0 inches. 3. For SBIP-400 series, no temperature test is required in a sign when the minimum spacing between the HID lamp and a polymeric material, between a HID lamp and adjacent ballast, or a HID lamp and other components is 9.0 inches. 4. A minimum spacing of 24 inches shall be kept between an HID lamp and combustible material located directly above the lamp. 5. These units shall not be mounted on combustible material or have combustible material located directly below them. LED power supply; Cat. No. CLM-1250, LPS-1250, BTL-2450, and LPS-2450. 1. LED power supply, Cat. No. for dry and damp locations. 2. Each power supply output is Class 2. 3. LED power supply shall be installed in a suitable electrical enclosure. 4. Adjacent LED power supplies shall be installed at least more than 1 in. end to end and 4 in. side to side. LED power supply; Cat. No BTL-24120, CLM-12120, LPS-12120, LPS-24120. 1. LED power supplies are for dry and damp locations. 2. Each power supply output is Class 2. 3. LED power supply shall be installed in a suitable electrical enclosure. 4. Adjacent LED power supplies shall be installed at least 1 in. from each other end to end and 4 in. apart in other directions. 5. All wiring must be rated 75C or greater. Class 2 LED Channel Lite; Cat. No. CLM - XXR, -E, -Y, -G, -B or -W followed by -RW or -RD, where "XX" represents 01 to 100 strings of LED modules. 1. LED power supply, Cat. No. for dry and damp locations. 2. Each power supply output is Class 2. 3. LED power supply shall be installed in a suitable electrical enclosure. 4. Adjacent LED power supplies shall be installed at least more than 1 in. end to end and 4 in. side to side. Class 2 LED Power Supplies; Cat. No. BTL-24120, CLM-12120, LPS-12120, LPS-24. 1. LED power supply, Cat. No. for dry, damp or wet locations. 2. Liquid tight conduit fittings required for wet location use. 3. Each power supply output is Class 2. 4. Adjacent LED power supplies shall be installed at least more than 1 in. (25mm) end to end and 2 in. (51mm) side to side. 5. For stationary equipment only. Leakage current exceeded 0.5ma. Leakage current is less than 0.75ma. Class 2 LED Channel Lite; Cat. No. CLM - XXR, -E, -Y, -G, -B or -W followed by -RW or -RD, where "XX" represents 01 to 100 strings of LED modules.

FUTUREMEDIA DISPLAYS INC #800 2120 HUTTON DR CARROLLTON, TX 75006

E316529

Sign Fan Cooling System, Series FMCPX-N Fan Cooling System, where X may be blank, 1, 2, 3 or 4 and N may be 1, 2, 3 or 4. 1. These components should be installed in accordance with the manufacturer's instructions. 2. These devices are to be used in accordance with the ratings and load types as specified below. Catalog Number (Input-Output) Operating Voltage (V) Max Output Current (rms) Input (AC) FMCPX-N Fan Cooling System 100-240 Output (DC) 12 5 Fans Type Load

3. These components are not provided with a suitable enclosure or sign body. The need for a suitable electrical enclosure and mechanical mounting means shall be considered in the end product. 4. No testing has been conducted on these units. The need to conduct Input, Temperature, Dielectric Voltage Withstand, and Grounding Continuity tests shall be considered in the end product. The need for additional testing shall also be considered in the end product. 5. The need for suitable strain relief of the internal wiring due to potential user servicing shall be considered in the end product.

GEMINI INC 103 MENSING WAY CANNON FALLS MN

E16382

55009

Plastic Channel Letters, Cat. No. Plastic Channel Letters. 1. The channel letters may be used as an electrical enclosure when provided with sign face material in the end-use application that is suitable for electrical enclosure use. 2. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 3. Openings for drain holes, conduit, electrode receptacles and mounting shall be provided in accordance with the Standard. 4. The channel letter plastic is rated 80°C. 5. For outdoor or indoor use. 6. Spacings from the channel letter to the enclosure for neon transformers or power supplies shall be in accordance with Standard UL 48.

36

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

Plastic Channel Letters, Plastic Indoor Channel Letters. 5. The channel letters have been evaluated for indoor application only. 6. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 7. Openings for conduit, electrode receptacles and mounting shall be provided in accordance with the Standard. 8. The channel letter plastic is rated 50°C. 9. The channel letter may be used as an electrical enclosure when provided with a sign face material in the end-use application that is suitable for electrical enclosure. 10. Spacings from the channel letter to the enclosure of neon transformers or power supplies shall be in accordance with Standard UL 48. Plastic Channel Letters and Face, Plastic Indoor Channel Letter Sign Body and Face 1. The channel letters have been evaluated for indoor application only. 2. The channel letters are not suitable as an electrical enclosure. 3. The channel letters are suitable for Class 2 LED and neon applications. 4. The channel letter plastic is rated 50°C. 5. Openings for conduit, electrode receptacles and mounting shall be provided in accordance with the Standard. 6. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 7. Spacings from the channel letter to the enclosure of neon transformers or power supplies shall be in accordance with Standard UL 48. Aluminum reinforced thermoplastic sign face trim, Type Gem Brand. 1. These trim materials are used to secure a rigid thermoplastic sign face to an outdoor or indoor sign. 2. The ability of the trim to exclude water from contacting live parts needs to be evaluated in the end product. 3. Minimum No. 8 sheet metal screws need to be provided for securing the trim to the sign body. The maximum spacing between screws shall not exceed 18 in. and no fewer than four screws are to be used per face. 4. These products do not comply with enclosure requirements. 5. The following are among the items to be considered in the end-use application. 1. Acceptable for use in wet locations. 2. Water exclusion must be determined in the end product. 3. Minimum 5 cm (2 in.) spacing from heat producing components required. 4. The specified solvents are continuously applied to edge of acrylic or polycarbonate sign face. Additional specified adhesives may be applied for the final bond. Solvent Final Bond Adhesive Sign Trim Generic Material Sign Face Generic Material Methyl Methacrylate Weld-On #4 or Weld-On #16, Weld-On Cellulose Acetate Butyrate (Acrylic) #58 ( Methylene Chloride ) (Polycarbonate) Weld-On #4 or Weld-On #58, Lord Cellulose Acetate Butyrate Methylene Chloride Adhesive #7550 Plastic Channel Faces, Type Gemini Gemlite Channel faces and Gemini Edge Glo faces 1. The sign faces have been evaluated for indoor & outdoor applications. 2. The sign faces are not suitable as an electrical enclosure. 3. The sign face plastic is rated 50°C. 4. The sign face for channel letter is not to be considered as providing a weatherproof enclosure, therefore all internal components shall be suitable for outdoor use or shall be completely enclosed and protected from weathering. 5. The neon tube or LED shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 6. The sign face may be used with either plastic or metal channel letters. Plastic Channel Letters, Type Indoor, outdoor designated "GEMINI FORMED SIGN BODY" for Class 2 powered LED modules strips. 1. These products are only suitable to house LED modules strips that are powered by UL Listed or R/C Class 2 Power Supply rated max 30 VDC or max 15 VAC. 2. These products are not suitable for use as electrical enclosures. 3. These products shall be provided with mounting instructions. 4. For outdoor applications, if these products are used to house components other than Class 2, then all internal components shall be suitable for outdoor use or shall be suitably enclosed. Plastic Channel Letters, Type Gemini Channel Letters 1. The Gemini Channel Letters have been evaluated for indoor & outdoor applications. 2. The Gemini Channel Letters are not suitable as an electrical enclosure. 3. The neon tube shall be spaced a minimum of 1/8 in. from the inside walls of the plastic enclosure, and 1/8 in. from the sign face. 4. The Gemini Channel Letter plastics are rated 80°C minimum. 5. Suitable for use in terminating conduit trade size up to ¾ in. 6. Water exclusion must be determined in the end product.

GOLDEN VALLEY OPTOELECTRONICS CO LTD LANGFANG DEVELOPMENT ZONE LANGFANG, HEBEI 065001 CHINA

E300609

LED Class 2 Kit, Cat. No. ACAXXX Series, where X may be the numbers 011, 013, 045, 046, 047 and 077. 1. Class 2 LEDs, ACAXXX Series: Each module is only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits. 3. Class 2 LEDs, ACAXXX Series: Modules ACA011 and ACA013 are each rated max. 3.2 Watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.

37

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 15 Volt AC or max. 30 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

GRATE SIGNS INC 4044 W MCDONOUGH ST JOLIET IL 60436

Structural Siding Cat. No. E-Z Channel Letter 1. The aluminum siding shall be bonded to the point of conduit connection to the sign. 2. The water tightness of the enclosure requires evaluation.

E227355

GUANGZHOU LINONG ELECTRONICS CO LTD 97 DAXIAN ST DONGHUA VILLAGE, RENHE TOWN BAIYUN DISTRICT GUANGZHOU, GUANGDONG 510470 CHINA

E256642

LED Class 2 Modules, Cat. No. LN-105H50WCI, LN-31102RGB, LN-4451RGB, LN-B310, LN-B510, LN-P460-UB290 and LNP515-UB290. 1. The final acceptance is to be determined when evaluating in the end-use product. 2. The LED modules are intended only for connection to the 15VDC output of a Class 2 power supply. 3. The LED modules have mounting feet for securement by screws. Other means of securement require evaluation. 4. No further evaluation is required unless there are heat producing components or uninsulated electrical terminals or parts in the same compartment. 5. The product shall be suitable for use in dry or damp location only such as inside the housing of an outdoor channel letter. LED Class 2 Modules, Cat. No. "LINONG LED illuminant modules", Model LNAXYZ series where X may be replaced with 15 or 60; Y may be replaced with B, G, R, Y and W; and Z may be replaced with numbers 2 or 3. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED Modules "LINONG LED illuminant modules", models, LNAXYZ, series is each rated max. 7.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

HANGZHOU WEILIGUANG TECHNOLOGY CO LTD 12 XIANGYUAN RD. XIANGFU TOWN GONGSHU DISTRICT HANGZHOU, ZHEJIANG 310011 CHINA

E303534

LED Class 2 Kit, Cat. No. CHD01. 1. Class 2 LEDs, ACAXXX Series: Each module is only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits. 3. Class 2 LEDs, ACAXXX Series: Modules ACA011 and ACA013 are each rated max. 3.2 Watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max. 15 Volt AC or max. 30 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end.

HEATRON INC. 3000 WILSON LEAVENWORTH, KS 66048

E316391

LED drivers Models HPS20-36V-0550, HPS20-24V-0830, HPS20-22V-0910, HPS20-18V-1100, HPS20-17V-1250, HPS20-15V1330, HPS20-13V-1540, HPS20-12V-1660, HPS20-10V-2000, HPS20-36-xxxxC, HPS20-24-xxxxC, HPS20-22-xxxxC, HPS2018-xxxxC, HPS20-17-xxxxC, HPS20-15-xxxxC, HPS20-13-xxxxC, HPS20-12-xxxxC, HPS20-10-xxxxC, xxxxC = Any alphanumeric characters for marketing purpose. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief and Impact Tests have not been investigated. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of each unit is V-2, and the necessity of additional fire barriers shall be determined in end product. LED drivers Models HPS40-36V-1100, HPS40-24V-1670, HPS40-22V-1820, HPS40-18V-2220, HPS40-15V-2680, HPS40-13V3080, HPS40-12V-3330, HPS40-10V-4000, HPS40-09V-4450, HPS40-36-xxxxC, HPS40-24-xxxxC, HPS40-22-xxxxC, HPS4018-xxxxC, HPS40-15-xxxxC, HPS40-13-xxxxC, HPS40-12-xxxxC, HPS40-10-xxxxC, HPS40-09-xxxxC, xxxxC = Any alphanumeric characters for marketing purpose.

38

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105°C. Output leads are Style 1430, No. 18 AWG, rated VW-1, 300 V, 105°C. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief and Impact Tests have not been investigated. The suitability of the enclosure as ultimate enclosure shall be determined in the end-use application. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of each unit is V-0 for Models HPS40-09, HPS1040-10, HPS1040-12, HPS1040-13, HPS1040-15, HPS1040-18, HPS-104022, and V-2 for Models HPS1040-24, HPS1040-36, and the necessity of additional fire barriers shall be determined in end product. LED drivers Models HPS25-36V-0700, HPS25-24V-1040, HPS25-12V-2080, HPS25-36-0700C, HPS25-24-1040C, HPS25-122080C, HPS90-36V-2660, HPS90-24V-4000, HPS90-19V-5000, HPS17-36V-0470, HPS17-24V-0700, HPS17-12V-1400, HPS17-36-0470C, HPS17-24-0700C, HPS17-12-1000C. xxxxC = Any alphanumeric characters for marketing purpose. 1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both primary and secondary circuits. 5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product. 6. When not marked for "Dry and Damp Locations Only" the power supply primary bracket shall be provided with min. 3.5 threads and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3. 5 threads, the liquid tight shall be provided with watertight fitting Listed (QCRV) 1/2 inch, liquid tight conduit fittings. 7. These products are suitable for use in commercial application only when marked with 277 V input voltage.

HIGH PERFECTION TECHNOLOGY CO LTD. 2ND FL 82-3 TUNG SHUN ST SHULIN , TAIPEI HSIEN 238 TAIWAN

E249377

Class 2 LED Power Supply, Cat. No. LP1060-Series with numerical suffix ­07 through 24 followed by suffix - one or two letters and - a single letter or number, and Model LP2046 followed by suffix ­ one or two letters and - a single letter or number. 1. These power supplies have a single output that complies with Class 2 output requirements. 2. These products are suitable for use in dry damp and wet locations only. 3. The primary sides of these power supplies are suitable for connection with threaded type conduit only. 4. The maximum rated output power for Model LP1060-13-YZ-E, LP1060-17-YZ-E and LP1060-21-YZ-E is 61 watts, for Model LP1060-24-YZ-E is 60 watts. 5. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 6. When not marked for indoor use only the power supply primary bracket shall be provided with min. 3.5 threads and tapered for connection to liquid tight conduit fitting. 7. When not marked for indoor use only, all models shall have liquid tight fittings on both primary and secondary circuits. Class 2 LED Power Supply, Cat. No. LP1040-09-Cnnnn, LP1040-10-Cnnnn, LP1040-12-Cnnnn, LP1040-13-Cnnnn, LP1040-15Cnnnn, LP1040-18-Cnnnn, LP1040-22-Cnnnn, LP1040-24-Cnnnn and LP1040-36-Cnnnn. where "Cnnnn" could be defined as any alphanumeric characters for marketing purpose, or blank. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. Input leads are Style 1015, No. 18 AWG, rated VW-1, 600 V, 105°C. Output leads are Style 1430, No. 18 AWG, rated VW-1, 300 V, 105°C. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief and Impact Tests have not been investigated. The suitability of the enclosure as ultimate enclosure shall be determined in the end-use application. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of each unit is V-0 for Models LP1040-09, LP1040-10, LP1040-12, LP1040-13, LP1040-15, LP1040-18, LP-1040-22, and V-2 for Models LP1040-24, LP1040-36, and the necessity of additional fire barriers shall be determined in end product. Class 2 LED Power Supply, Cat. No. LP1020-10-Cnnnn, LP1020-12-Cnnnn, LP1020-13-Cnnnn, LP1020-15-Cnnnn, LP1020-17Cnnnn, LP1020-18-Cnnnn, LP1020-22-Cnnnn, LP1020-24-Cnnnn and LP1020-36-Cnnnn, where the optional suffix "Cnnnn" may be any alphanumeric character. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief and Impact Tests have not been investigated. 6. The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.

39

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

Class 2 LED Power Supply, Cat. No. LP4240-24-xy, LP4240-15-xy, LP4240-12-xy, LP3240-15-xy and LP3240-24-xy 1. These power supplies have multiple outputs. Power supply Model LP4240-24-xy, LP4240-15-xy and LP4240-12-xy have a maximum of four Class 2 outputs. Power supply Model LP3240-24-xy has maximum three Class 2 outputs. Each output of these power supplies have been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 4. When not marked for indoor use only, all units shall be provided with liquid tight fittings on the primary and secondary circuits. Class 2 LED Power Supply, Models LP1025-12, LP1025-24, and LP1025-36; may be followed by optional suffix Cnnnn, where nnnn may be any alphanumeric characters, LP1017-12-Cnnnn, LP1017-24-Cnnnn and LP1017-36-Cnnnn, where nnnn may be any alphanumeric characters, and LP1090-XX-YZ-E, where XX can be 19, 24 or 36; Y can be G or T; Z can be G or T; and E can be any number from 170 to 999. 1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both primary and secondary circuits. 5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product. 6. When not marked for "Dry and Damp Locations Only" the power supply primary bracket shall be provided with min. 3.5 threads and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3. 5 threads, the liquid tight shall be provided with watertight fitting Listed (QCRV) 1/2 inch, liquid tight conduit fittings. 7. These products are suitable for use in commercial application only when marked with 277 V input voltage.

HUDNUT CO INC 730 NE 21ST AVE PORTLAND, OR 97232

E257980

Class 2 LEDs, Cat. Nos. Class 2 LED Strip. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, maximum 30 volt continuous (noninterrupted) DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp, and wet locations. 5. In a wet location, these products are not required to be enclosed or protected from weather.

I LIGHT TECHNOLOGIES 1588 BROWN AVE. COOKEVILLE, TN 38501

E223028

Class 2 LEDs, Cat. Nos. PN60112DCR-3R, PN10124DCR-3R, PNC224012DCR-3R, PNC224024DCR-3R. 1. These power supplies have been evaluated for use in LED signs. 2. The power supplies have outputs that individually comply with Class 2 circuit requirements. 3. These units are suitable for use in dry and damp locations without a need for an additional enclosure. 4. The output of this power source shall not be connected to any other power source or provide power to components connected to another power source. 5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at least 150 mm (6 in) inside.

ILLUMAGRAPHICS L L C 165 SPRING HILL DR. GRASS VALLEY, CA 95945

E219395

Electroluminescent Display Panel System, Cat. Nos. "Merchandiser" 1. The electroluminescent panels are suitable for installation in a dry or damp location. The controller and direct plug-in units are suitable for installation in a dry location. 2. The electroluminescent panel must be located where made inaccessible by the thermoplastic barrier provided with the system. 3. The controller and cabling from the controller to the electroluminescent panel are intended to be made inaccessible in the end product.

40

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

IMAGINE SIGNS L L C 6006 SHULL ST BELL GARDENS, CA 90201

E250540

Class 2 LEDs, Cat. Nos. "LED Pricer Changer". 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 Volt or less DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These Class 2, "LED Module Pricer" Series when connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations.

INTERTEK CORP 4TH FL 81 HSIN TAI-WU RD, SEC 1 HSIN-CHIH, TAIPEI HSIEN 221 TAIWAN

E307120

Class 2 LED Power Supply, Models APP200AC-12, APP200AC-15, APP200AC-24, APP200AC-30. 1. These power supplies have not been provided with a suitable enclosure. In the end product these units shall be enclosed. 2. When used in a cord-connected products, the need for conducting a leakage current test shall be considered in the end product. 3. The product was tested for use at the maximum ambient temperature (Tma) of 60°C permitted by the manufacturer's specification. This product will need to be temperature tested in the end product and ambient cannot exceed 60° C. 4. These components are suitable for use in damp locations. 5. The Class 2 output of these power supplies are acceptable for use in a damp location without an additional enclosure. The Class 2 output of Models APP200AC-12, APP200AC-15 are also acceptable for use in a wet location without an additional enclosure. 6. These components have been investigated for use on a maximum branch circuit rating of 20A. Class 2 LED Power Supply, Models APP200AC-48. 1. This power supply has not been provided with a suitable enclosure. In the end product this unit shall be enclosed. 2. When used in a cord-connected products, the need for conducting a leakage current test shall be considered in the end product. 3. The product was tested for use at the maximum ambient temperature (Tma) of 60°C permitted by the manufacturer's specification. This product will need to be temperature tested in the end product and ambient cannot exceed 60° C. 4. This component is suitable for use in damp locations. 5. This component has been investigated for use on a maximum branch circuit rating of 20A. Class 2 LED Power Supply, Models ANP90-12P, ANP90-12PY, ANP90-15P, ANP90-15PY, ANP90-19P, ANP90-19PY, ANP9024P, ANP90-24PY, ANP90-24P1, ANP90-24P1Y, ANP90-30P1, ANP90-30P1Y, ANP240-12P, ANP240-15P, ANP240-19P, ANP240-24P, ANP155-12AC, ANP155-15AC, ANP155-19AC, ANP155-24AC. 1. These power supplies have a maximum of four Class 2 outputs. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 2 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both primary and secondary circuits. Tradename is "Amperor"

IPAN LED INC SUITE D 55 QUINTA CT SACRAMENTO, CA 95823

E315810

Class 2 LED Modules, Cat. Nos. LBY-FXXQYZTMMMM series, where XX may be 12, Q may be S or F, Y may be 48 or 78, Z may be B, G, R, W, Y or RGB, T may be any numerals from 1 to 9 and MMMM may be blank or any alphanumeric characters. 1. These products have not been evaluated for use when connected to the Class 2 output of a Listed or Recognized Component power source rated 12 V DC. 2. These products are suitable for use in dry, damp and wet locations. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. Border Lights LED Modules, Cat. Nos. Cat. No. LBY-D26X144-V series, where X may be B, G, R, W, Y or RGB and V may be 24. 1. These products have been evaluated for use only when connected to the Class 2 output of a Listed or Recognized power source rated 24 Volts DC. 2. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 V dc or less. 3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. Class 2 LED Controller, Cat. Nos. LBY-S3P200W-1. 1. These products have been evaluated for use only when connected to the Class 2 output of a Listed or Recognized Component power source rated 12 V DC. 2. Class 2 LED Controller, Cat. No.LBY-S3P200W-1 is rated max. 24 Watts. When connected to a Class 2 circuit, these units are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.

41

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

3. These products are not required to be enclosed or protected from the weather in the end product. 4. These products may be secured in place in the end product by any means available. 5. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall be considered.

J & J ELECTRONICS INC 7A WHATNEY IRVINE, CA 92618

E256424

Class 2 LEDs, Cat. Nos. CL-YY-XXXXX, where XXXXX is any alpha numeric code denoting LED color and YY may be replaced by any combination of numbers from 00 to 99 to indicate the number of LEDs 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12 VAC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. Class 2 LED Channel Letter Lighting is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit. The following identifies the rating to be used in calculating the maximum number of units per circuit. Cat. No. CL-YY-xxxxx mA Load per module depending on color 25-350 Watts 0.3-4.2

4. These products are suitable for use in dry, damp and wet locations without additional enclosures.

JEFFERSON ELECTRIC INC. 9650 S FRANKLIN DR FRANKLIN, WI 53132

E258996

LED power supply with Class 2 output, Cat. Nos. Cat. No. 412-C001-002. 1. This power supply has 4 outputs. The output has been evaluated and found to comply with Class 2 output requirements. 2. This power supply is provided with a metal enclosure that is suitable for use in wet locations in the marked orientation. (Class 2 knockouts on bottom.) 3. Each output of this power supply is rated 12 V AC, 4.5 amps. 4. Each power supply shall be installed in accordance with the installation instructions. 5. Spacing between adjacent power supplies is one inch end to end and 4 in any other direction.

JEWELITE WAGNER ZIP-CHANGE INC. 3100 HIRSCH ST. MELROSE PARK, IL 60160

E90751

Aluminum Reinforced Sign Face Trim, Cat. Nos. Jewelite, J-Trim, Neonlite, VHB/Jewelite. 1. The Jewelite trim, bonded to a thermoplastic sign face is not to be considered as providing a weatherproof enclosure, therefore all internal components shall be suitable for outdoor use or shall be completely enclosed and protected from weathering. 2. The following combination of sign trims bonded to sign faces were subjected to oven, freezing and humidity tests: Generic Material Solvent Sign Trim Material Methyl Methacrylate Methylene Cellulose Acetate (Acrylic) Chloride Butyrate Polycarbonate Goodyear Cellulose Acetate Pliobond Butyrate Polycarbonate General Electric Cellulose Acetate Sign Bond Butyrate If any other combination is used, the above mentioned tests should be repeated. 3. A 720 h ultraviolet radiation test was conducted on the subject sign trim in order to determine the effects of ultraviolet (UV) radiation on outdoor signs employing the Jewelite trim. Flammability and electrical characteristics of the cellulose acetate butyrate sign trim have not been evaluated. 4. The suitability of internal wiring and connections should be evaluated in the end-use application. 5. All metal is painted or plated to provide a means for protection against corrosion. 6. Components that are employed in the end product should be evaluated with respect to suitability of construction, test performance, electrical rating, mounting and operating temperature. 7. VHB/Jewelite is suitable for acrylic and polycarbonate sign faces for indoor or outdoor use. It shall be applied in accordance with the instructions.

42

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

JOHNSON WALKER & ASSOCIATES L LC, DBA IMPERIAL PLASTICS MFG Suite 1 244 S COURT ST LAPEER, MI 48446

E225580

Aluminum Reinforced Sign Face Trim, designated Signatrim. 1. The Signatrim, bonded to a thermoplastic sign face is not to be considered as providing a weatherproof enclosure, therefore all internal components shall be suitable for outdoor use or shall be completely enclosed and protected from weathering. 2. The following combination of sign trims bonded to sign faces were subjected to oven aging, freezing and humidity tests: Sign Face Sign Trim Generic Material Solvent Generic Material Cellulose Acetate Butyrate Methyl Chloride Cellulose Acetate Butyrate Polyethyl Metbacrylate Methyl Methacrylate Methyl Chloride Polyethylene TerephthalatePolycarbonate Methyl Chloride PETG Acrylic Cyanoacrylate PETG Polycarbonate Cyanoacrylate PETG If any other combination is used, the above mentioned tests should be repeated. 3. A 720 h ultraviolet Radiation Test was conducted on the subject sign trim in order to determine the effects of ultraviolet (UV) radiation on outdoor signs employing the Signatrim. Flammability and electrical characteristics of the cellulose acetate butyrated sign trim have not been evaluated. 4. The suitability of internal wiring and connections should be evaluated in the end use application. 5. All metal is painted or plated to provide a means for protection against corrosion. 6. Components that are employed in the end product should be evaluated with respect to suitability of construction, test performance, electrical rating, mounting and operating temperature.

JS LED POWER INC 4611 MONTEREY AVE BALDWIN PARK, CA 91706

E308859

Class 2 LEDs, Cat. Nos. JE-001X (HS-F504BR4TN), JE-002X (HS-F504BN4TN), JE-003X (HS-F504BB4TN), JE-004X, JE005X (HS-F504BY4TN) and JE-006X (HS-R483AR4CY or HS-R484CN4CY or HS-R484CB4CY), where X may be replaced with A, B, G, M, R or W. 1 These products are only suitable for connection to a Class 2 power source, rated 15 Volt (DC or AC) or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LEDs, cat. nos. JE-001X, JE-002X, JE-003X, JE-004X, JE-005X and JE-006X are each rated max. 15 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product. Class 2 LEDs, Cat. Nos. JE-001RU, JE-002GU, JE-003BU, JE-004WU and JE-005AU. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt (DC or AC) or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED modules, cat. nos. JE-001RU, JE-002GU, JE-003BU, JE-004WU and JE-005AU are each rated max. 12 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product.

JUSTIN INC 2663 N LEE AVE SOUTH EL MONTE

E235322

CA 91733

Class 2 Power Supply, Model 601-12DC, 601-12DCR, 101-24DCR, C2240-12DCR, C2240-24DCR, C2240-12, C2240-12240, C2240-24, and C2240-24-240. 1. These power supplies have been evaluated for use in LED signs. 2. The power supplies have outputs that individually comply with Class 2 circuit requirements. 3. These units are suitable for use in dry and damp locations without a need for an additional enclosure. 4. The output of this power source shall not be connected to any other power source or provide power to components connected to another power source. 5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at least 150 mm (6 in) inside. Class 2 Power Supply, Model 601-12DC-LC, 601-12DCR-LC, 101-24DCR-LC, C2240-12DCR-LC, C2240-24DCR-LC, C224012-LC, C2240-12-240-LC, C2240-24-LC, and C2240-24-240-LC. 1. These power supplies have been evaluated for use in portable LED signs. 2. The power supplies have outputs that individually comply with Class 2 circuit requirements. 3. These units are suitable for use in dry and damp locations without a need for an additional enclosure. 4. The output of this power source shall not be connected to any other power source or provide power to components connected to another power source. 5. The attachment plug on the end of the power supply cord is not to be removed.

43

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

LAMINATORS INC 3195 PENN AVE PO BOX 39 HATFIELD PA 19440

E60612

Structural panels, consisting of a plywood core faced on both sides with sheet metal, Type S2S. 1. The structural panel may be employed as external decorative faces and for the support of complete electrical enclosures. 2. The structural panel is not to be used to enclose bare live parts or wiring. 3. Enclosures, plastic faces, and moldings may rely upon the structural panel for support. These components are to be reliably secured to the panel. 4. Sheet metal screws may be used when fastening a ballast or transformer weighing more than 7-1/2 lbs. (3.4 kg). 5. All exposed edges of the structural panel, including drilled holes, etc., shall be treated with two coats of asphalt-based paint, or a R/C Sign Accessory (UYMR2) wood coating. Structural panels, consisting of a high density polyethylene core faced on both sides with sheet aluminum, Types "Alumalite" , "Econolite" or "D-Lite". 1. The structural panel may be employed as external decorative faces and for the support of complete electrical enclosures. 2. The structural panel is not to be used to enclose bare live parts or wiring. 3. Enclosures, plastic faces, and moldings may rely upon the structural panel for support. These components are to be reliably secured to the panel. 4. Any parts other than neon standoffs or small decorative parts must be secured to the panel by bolts, nuts and washers of minimum 7/16 in. diameter. Structural panels, Model CPA, Type D-Lite, consisting of a high density polyethylene or polypropylene core faced on both sides with sheet aluminum, intended for use in electric signs 1. The structural panel may be used as part of the sign body but shall not be used as part of an electrical enclosure. All bare live parts or wiring shall be enclosed in a wireway complying with the Standard for Electric Signs. 2. Any parts other than neon standoffs or small decorative parts secured to the panel must be secured by means of through bolts, nuts and washers having min 7/16 in dia measuring across. 3. Gasketing of permanently secured panels may be provided by the application of a hardening, outdoor caulking compound. 4. The backing shall not be subjected to a temperature of more than 90 degrees C (194 degrees F). 5. The backing shall not contact any electric discharge tube, fluorescent lamp or fluorescent lamp starter. 6. The metal faces shall be grounded in accordance with the Standard for Electric Signs (UL 48). Separate grounding straps shall be used when necessary.

LED EFFECTS INC. 11390 SUNRISE GOLD CIR RANCHO CORDOVA, CA 95742

E250837

Class 2 LEDs, Cat. No. LED Light Fixture H2 Series. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products when connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 circuit. 5. These products are suitable for use in dry, damp and wet locations.

LED INC. #22 1601 FAIRVIEW DR CARSON CITY, NV 89701

E255480

LED Illumination Modules, Cat. No. Series 04021-XXXX and 04022-XXXX, where XXXX can be 2000, 4000, 5000, 6000 or 9000 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 15 V. 3. Class 2 LEDs, Series 04021-XXXX and 04022-XXXX are each rated max. 1.2 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Illumination Modules, Cat. No. Series 04024-XXXX where XXXX can be 2000, 4000, 5000, 6000 and 9000. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 15 V. 3. Class 2 LEDs, "1 Watt High Power LED Module", model designation 04024-9000 is each rated max. 3.0 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Illumination Modules, Cat. Nos. 04022-8800 and 04025-XXXX series, where XXXX can be 2000, 4000, 5000, 6000 and 9000. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 15 V.

44

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

3. Class 2 LED modules, Cat. No.04022-8800 and 0Cat. No. 4025-XXXX are each rated max. 1.2 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product. Flexible LED Modules, Cat. Nos. 06031-XXXX series, where XXXX can be 2000, 4000, 5000, 6000, 8000, 9000 or 9001. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 15 V. 3. Class 2 LED modules, Cat. No. 06031-XXXX series are each rated max. 7.0 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

LED SIGN PRODUCTS, INC. 1749 E 28TH ST SIGNAL HILL, CA 90806

E227766

LED Illumination Strips, Cat. No. 83063, 83063-3, 83063-04. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products are not provided with break points in the printed wiring board. No cuts across the board is permitted. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather.

LEDPAC #14 9830 SIMPRE VIVA RD SAN DIEGO, CA 92154

E257619

LED Illumination Modules, Cat. No. Class 2- Self Contained, Injection Molded Continuously Wired LED Packs / Interchangeable Clear UV Protective Caps, Models XLP, SLP. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Illumination. XLP is a series of 3 LEDS that draws 350mA. A total of only 14 of these units can be connected to a Class 2 output circuit (based on 5 amps max.). SLP is a series of 2 LEDS that draws 50 to 70mA. A total of only 70 of these units can be connected to a Class 2 output circuit (based on 5 amps max.). 4. Class 2 LED Illumination, these products are provided with R/C wire soldered onto the printed wiring board for connection in series. 5. When connected to a Class 2 circuit, 12 volt output supply, these LEDs are suitable for installation in wet locations, damp, and dry locations. 6. These products are not required to be enclosed or protected from weather.

LEOTEK ELECTRONICS CORP. 50 LUNG-YUAN 7TH RD. LUNG-TAN TAOYUAN HSIEN, TAIWAN

E232725

Class 2 LED Channel Lite, Cat. Nos. CLM-XXR, E, Y, G, B or W, followed by ­RW or -RD where XX represents 01 to 100 strings of LED modules. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED "Channel Lite", CLM-XXR, E, Y, G, B, or W followed by -RW, module is rated 0.3 Watts per module. When modules are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 4. LM-XXR, E, Y, G, B, or W followed by -RW, modules are provided with wire soldered on the printed wiring board for connection. 5. These products are suitable for use in dry, damp and wet locations. These products are not required to be enclosed or protected from weather. Class 2 LED Tubes, Cat. Nos. "BTL-96X-PAX" Series, where "X" may be replaced by B, G, W, R, E and Y 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 volt DC power source or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 4. These products are provided with wire soldered on the printed wiring board for connection. 5. These products are suitable for use in dry, damp and wet locations when provided with housing for Class 2 LEDs.

45

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

Class 2 LED Modules, Cat. No."PEM-XXX" Series, where XXX is any alpha-numeric combination denoting LED color, type, or number of modules. 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component ­ Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12VDC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 power supply. 4. These products are suitable for use in dry, damp and wet locations without additional enclosures.

LIGHTECH ELECTRONIC INDUSTRIES LTD 9 HAMELACHA ST. NORTHERN INDUSTRIAL ZONE 71520 LOD, ISRAEL

E242790

Class 2 Power Supply, Models LET-60, LED 25 8V, LED 25 12V, LED 25 24V, LED 10CV 12, LED 10CV 12 PU, LED 10CV 24, LED 10CV PU, LED 10CC 350, LED 10CC 350 PU. 1. The power supply shall be installed in compliance with the enclosure, mounting, spacing, casualty and segregation requirements of the end product. 2. Abnormal and Component Failure Tests were conducted with the power supply input protected by a 20 A circuit breaker. The need for repeating these tests in the end product shall be considered, if installed in a circuit having a higher rated protective device. 3. For power supply models provided with a metal enclosure, grounding and/or bonding requirements in the end-use application should be considered. An optional configuration of this unit contains a ground wire. This version of the unit does not necessarily have to be bonded to the end product. 4. All tests for Model LET-60 were performed using a 12V 60 W load. All tests for the LED 25 models were performed using a 24 W load. Acceptability of other loads is to be evaluated during the end product investigation. 5. The input/output connectors have not been evaluated for field connections and are only intended for connection to mating connectors of internal wiring inside the end product. 6. Temperature limits were derived with the product placed on an open bench during test and can therefore not be indicative of the temperature in the final application. Temperature testing should therefore be considered in the final application to ensure that the unit's enclosure "hot spot" does not exceed Class A temperature limits. 7. A suitable Fire and Electrical Enclosure shall be provided in the end product. 8. These units are suitable for use in dry locations only.

LIGHTWILD L C SUITE 100 7304 W 130TH ST OVERLAND PARK, KS 66213

E303645

LED Class 2 LEDs, Model No. Models: LW-UP-19-1C, LW-UP-19-1S, LW-UP-19-2S, LW-UP-19-3S, LW-UP-19-4S, LW-UP-191R. 1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. These products are suitable for use in dry and damp locations. 4. Lead wires are not Listed Class 2 cable. Therefore leads must be enclosed in a sign housing, wireway, raceway, or electrical enclosure.

LORD CORP CHEMICAL PRODUCTS DIV 2000 W GRANDVIEW BLVD ERIE PA 16514

E225855

Acrylic adhesives, Lord 201/19, -403/19, -406/19, -406/19 Red, -410/19. 1. The use of these adhesive systems shall be employed in an applications wherein the limitations as set forth in Table A are not exceeded. 2. These systems may be used for securement to any combination of surfaces listed in Table A, provided the use temperature is no higher than the lowest temperature rating of any element of the combination. 3. These systems are also suitable for use outdoors where exposed to high humidity or water. The minimum temperature rating is -35°C (-31°F). 4. These systems are suitable for application to smooth flat surfaces prepared in accordance with adhesive manufactures instructions. The need for adhesive bond strength test when applied to another surface or configuration shall be determined in the particular end use application. 5. The materials have been evaluated for adhesive compatibility and stability only. Adhesive shall be applied in continuous bead when used as water seal. 6. Means need to be provided for grounding metal parts that may become energized. 7. When considering the use of these adhesives, one square inch of surface covered by adhesive can support in shear tension the weight specified below.

46

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

TABLE A Max. Temp. 2 Adhesive Substrates °C lbs/in. 403/19, Aluminum, 130 472 406/19, Stainless steel, 406/19 Cold Rolled steel Red, 410/19 201/19 Aluminum 110 615 Urethane adhesive, Lord 7542A/D, -7542A/B, -7542A/C, -7542A/E. 1. The use of these adhesive systems shall be employed in applications wherein the limitations, as set forth in Table A, are not exceeded. 2. These systems may be used for securement to any combination of surfaces listed in Table A, provided the use temperature is no higher than the lowest temperature rating of any element of the combination. 3. These systems are suitable for application to smooth flat surfaces prepared in accordance with adhesive manufactures instructions. The need for adhesive bond strength test when applied to another surface or configuration shall be determined in the particular end use application. 4. The materials have been evaluated for adhesive compatibility and stability only. Adhesive shall be applied in continuous bead when used as water seal. 5. Means need to be provided for grounding metal parts that may become energized. 6. When considering the use of any adhesive covered by this Report. One square inch of surface covered by adhesive can support in shear tension the weight specified below. TABLE A 2 Adhesive Substrates Max. Temp. °C lbs/in. 7542A/D, 7542A/B, 7542A/C, 7542A/E Polyphenylene oxide (PPO) thermoplastic 90 191

LUCERE LIGHTING CONCEPTS L L C 10464 KINGSTON HUNTINGTON WOODS, MI 48070

E252547

LED Strip, Model 974 with suffix letters. 1. The final acceptance is to be determined when evaluating in the end-use product. 2. The LED boards are intended only for connection to the 12VDC output of a Class 2 power supply. 3. The LED boards are mechanically secured to aluminum channel or a fabricated aluminum housing with a polycarbonate lens. No further evaluation is required unless there are heat producing components or uninsulated electrical terminals or parts in the same compartment. Alternatively may be secured by screws in accordance with instructions. 4. The product shall be suitable for use in dry location only.

LUMI SPEC INC. 127 HIGHLAND CRES TORONTO ON M2L 1H2, CANADA

E237485

Class 2 LED Illumination Module, Cat Nos. Models LSRM Series. 1. These LED boards must be connected to a Class 2 UL Listed or Recognized 10 Volt DC power source. 2. These LED boards have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These LED boards are suitable for use in dry, damp and wet locations. 4. The mounting means and suitable enclosure shall be provided with end product. 5. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the maximum secondary or output current rating of each Class 2 circuit. Each LED board is rated 0.3 W. This rating is to be used in calculating the maximum number of units per circuit. 6. The optional connector suitable for 5 A max. 105 °C.

LUMIFICIENT TECHNOLOGIES L L C 290 COON RAPIDS BLVD COON RAPIDS MN 55433

E230262

LED kit for use in new signs, Model HRL-06-PFC-96, HRL-06-PFC-24 Class 2 Power Unit power unit, HYPERION R-Lite System-LED tape, HLR-PC power connector, and HRL-IDC Power IDC connector. 1. The HRL-06-PFC-96 power unit was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40C. 2. The HRL-06-PFC-96 power unit is provided with a conduit fitting suitable for 1/2 in. Trade Size rigid nonmetallic conduit. 3. The HRL-06-PFC-96 power unit, HYPERION R-Lite System-LED tape, HLR-PC power connector, and HRL-IDC Power IDC connector are suitable for dry or damp locations. LED Driver; Cat. No. Model HRL-06-PFC-96, HRL-xx-PFC-96yy where xx denotes 06 original model or 07 Alternate constructions, where yy denotes BM for the use of the CBI circuit breaker Model No. (BFQ1PA-B07XC-0500X), Class 2 Power Unit. 1. The HRL-06-PFC-24 power unit was tested for a maximum manufacturer's recommended ambient (Tmra) of 40(C. 2. The HRL-06-PFC-24 power unit is intended for installation inside an electrical enclosure. Minimum spacing between adjacent power units is 4 in. 3. The HRL-06-PFC-24 power unit is suitable for dry or damp locations.

47

SIGN COMPONENTS MANUAL (SAM)

E319521

April 21, 2008

LUMILENS OPTOELECTRONICS 5625-A S ARVILLE ST LAS VEGAS, NV 89118

Class 2 LED Modules , , Cat. No. LMMS-XXXX-YY-ZZ series, where XXXX may be replaced with any numbers 0000 to 9999; and, YY and ZZ may be replaced with any numbers 00 to 99. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 24 V DC. 3. Class 2 LED modules, Cat. no. LMMS-XXXX-YY-ZZ series are each rated max. 1.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations when rated maximum 15 V. Products that are rated a maximum of 24 VDC are suitable for dry and damp locations only. 5. These products are not required to be enclosed or protected from the weather in the end product when connected to a maximum of 15 V. 6. These products may be secured in place in the end product by any means available. 7. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall be considered.

LUMINATION L L C 6180 HALLE DR VALLEY VIEW, OH 44125 USA

E219167

LED Strip Cat. Nos. GExxxxxx-xxx. 1. Suitable for dry and damp locations. LED Connector Cat. No. GExxCLCMz. 1. Suitable for dry and damp locations. LED Wire Cat. No. GECLSWy. 1. Suitable for dry and damp locations. Splice Connector; Cat. No. GECLSCz. 1. Suitable for dry and damp locations. Canopy Kits Kit includes: GECPL (8 ft length), GECPEC (end cap), GECPLC, (lens connector), GEBTBCL, GEBTBC. 1. Border Tube Kit and Canopy Kit are for Wet Location only use when enclosing LED's connected to a Class 2 circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. 2. The LED border tube kit and Canopy Kit was not evaluated as an electrical enclosure. 3. The LED border tube kit and Canopy Kit was not evaluated as a watertight housing. Light Guide Kits Kit includes: GEXNLGXX-XXX, GEXNLGECXX-XXX, GEXNLGCXX-XXX, GEXNMCXX, GEXNSXX. 1. Border Tube Kit and Canopy Kit are for Wet Location only use when enclosing LED's connected to a Class 2 circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. 2. The LED border tube kit and Canopy Kit was not evaluated as an electrical enclosure. 3. The LED border tube kit and Canopy Kit was not evaluated as a watertight housing. End caps; Cat. No. GECLECz. Where x may be any alpha letter representing LED color. Where y may be any number representing wire length. Where z may be any number representing quantity. 1. LED power supply; Cat. No. GECLPS2 for dry location use only. 2. LED strip Cat. No. GExxCLSy, LED connector Cat. No. GExxCLCMz, LED wire Cat. No. GECLWRy, splice connectors Cat. No. GECLSCz, and end caps Cat. No. GECLECz for dry and damp locations 3. Each output is LPS or Limited Power Source. LED power supplies; Cat. No. GECLP2, GECLPS3, GECLPS4, GECLPS4D, GECLPS5, GECLPSWH and GECLPS6. 1. For dry and damp locations. 2. Each power supply output is Class 2. LED power supplies; Cat. No. GECLPS2, LED strip Cat. No. GExxxxxx-xxx, LED connector Cat. No. GExxCLCMz, LED wire Cat. No. GECLSWy, splice connectors Cat. No. GECLSCz, and end caps Cat. No. GECLECz. 1. LED power supply; Catalog No.GECLPS2 for dry location use only. 2. LED strip Cat. No. GExxxxxx-xxx , LED connector Cat GExxCLCMz, LED wire Cat. No. GECLSWy, splice connectors Cat. No. GECLSCz, and caps Cat. No. GECLECz for dry and damp locations. 3. Each output is LPS or Limited Power Source. LED Border Tube Kit Cat. Nos. Lens Cat. No. GExxBTL; Lens Connector Cat. No. GExxBTLC; End Cap Cat. No. GExxBTLEC; Exterior Corner Kit Cat. No. GExxBTLXC; Interior Corner Kit Cat. No. GExxBTLIC; Base Reflector Cat. No. GEBTBR; Base Connector Cat. No. GEBTBC; Cam Lock Cat. No. GEBTCL 1. Border Tube Kit is for Wet Location only use when enclosing LED's connected to a Class 2 circuit operating at under 30V continuous DC, 12.4 V interrupted at a rate of 10-200Hz DC, or 15 VAC. 2. The LED border tube kit was not evaluated as an electrical enclosure. 3. The LED border tube kit was not evaluated as a watertight housing. LED array drivers, Models GEXLPS21, GEXNPS30-120, GEXNPS31-120. 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 5. The drivers are intended for installation inside an electrical enclosure.

48

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

6. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. 7. The drivers are suitable for both dry and damp location use. LED Strips Cat. Nos. Cat. Nos. GEBLCLS1, GEBLCLS1-100, GEBLCLS4, GEBLCLS5, GEBLCLS5-120, GEGLCLS1, GEGLCLS1-100, GEGLCLS5, GEGLCLS5-120, GELYCLS1, GEPOCLS1, GEPOCLS5, GERCCLS1, GERCCLS5, GERDCLSWA1, GERDCLSWA5, GESBCLS1, GESBCLS1-100, GESBCLS5, GESBCLS5-120, GEWHCLS1, GEWHCLS8-55K, GEWHCLS8-65K, GEWHCLS8-95K, GEWHCLSX, GEYACLS1, GEYACLS5, GEYGCLS1, GEYGCLS5, GEWMPGP6-65K, GEWMPGP6-35K, GERDMXS6, GEGLMXS6, GEBLMXS6, GEWHMXS6, GEWWMXS6, GERDMXL6, GEGLXCS1-12V, GEGLXCS1-24V, GEGLXCS5-12V, GEGLXCS5-24V, GEGLXLS1, GEGLXLS5, GELYXLS1, GERCXLS1, GERDXLS1, GERDXLS5, GERDXLSWA1, GERDXLSWA5, GESBXLS1, GESBXLS5, GEWHPTS2-55K, GEWHPTS2-65K, GEWHPTS2-75K, GEWHPTS3-55K, GEWHPTS3-65K, GEWHPTS3-75K, GEWHPXS1-65K, GEWHPXS2-55K, GEWHPXS2-65K, GEWHPXS275K, GEWHPXS3-55K, GEWHPXS3-65K, GEWHPXS3-75K, GEWHXCS1-12V, GEWHXCS1-24V, GEWHXCS5-12V, GEWHXCS5-24V, GEWHXLS1, GEWWPXS4-32K, GEYGXLS1, GEYGXLS5, GEYATM12, GEYATMXW-SCS, GEYATMXW12, GEYAXNLE1, GEWWXNLE1, GEWWTM12, GEWWTMXW9, GEWWTMXW9WD, GEWWTU6, GERDTM12, GERDTMXW-SCS, GERCXNLE1, GERDCLS1, GERDCLS4, GERDCLS5, GEGLXNLE1, GEGRTM12, GEGRXNLE1, GEGLTMXW9, GEBLXNLE1, GEBLTMXW9, GEBLTM12, GEPOTMXW12. Splice connector; Cat. No. GexxSCx, End caps; Cat. No. GexxECx, LED Wire Cat. No. GExxSWx. 1. These products are only suitable for connection to a Class 2 power source. 2. When units are connected to a Class 2/"LPS" circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2/"LPS" supply. 3. These products are suitable for use in dry, damp and wet locations. 4. These products described in this section may be cut into segments per manufacture insulation instructions. 6. Units may be provided with UYMR2, 3M type VHB double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of Use" as defined in the Sign Components Manual. Power supplies with Class 2 outputs, Models GEPS24-80, GEPS12-60. 1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp locations. 2. These power supply needs to be installed in an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110 C. Similarly, for Model SDMV2420A, a temperature test is required when installed in an enclosure smaller than 13.5 by 6 by 4 inches, but the maximum temperature on the output transformer by thermocouple is 90 C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location Nomenclature for Splice Connectors, LED Wires, End Caps: xx denotes product line, CL = channel letter, XL = tetra long strip, PT = power tetra, XN = Exposed Neon, TM = Mini, MX = Max, TU = Ultra, PG = Power Grid, PX = Power White XL, PH = Power White HO, XH = Power White XL HO, MM = Mini Max. x denotes design revision number.

LUMIRON INC. # A-33 20725 NE 16TH AVE. MIAMI, FL 33179

E242758

Class 2 LEDs, Cat. No. Models Series LM, LMG, LMP, LMR, LMS, LMT. . 1. These modules have been evaluated for use on a UL Listed or Recognized Class 2 power source rated 12 V DC or 24Vdc. 2. The suitability of supply sources other than Class 2 has not been evaluated and shall be determined in the end-product. Special consideration shall be given to the enclosure and spacing requirements in UL48. 3. These modules are suitable for use in dry, damp or wet locations. They are not required to be enclosed or protected from weather. 4. The total wattage drawn by all modules connected to a single Class 2 supply shall not exceed the rated capacity of that supply.

MAGTECH INDUSTRIES CORP 5625-A S ARVILLE ST LAS VEGAS, NV 89118

E314969

Class 2 LED Module, Cat. No. LP12060P-08, LP12060P-09, LP12060P-10, LP12060P-11,LP12060P-12, LP24060P-22, LP24060P-23,LP24060P-24. 1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on both primary and secondary circuits.

49

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

MAXBRITE LED LIGHTING TECHNOLOGY L L C 1740-B JUNCTION AVE. SAN JOSE, CA 95112

E314210

Class 2 LED Module, Cat. No. OTH-308X10x18-01 Series, x: indicate the COLOUR: R-Red, Y-Yellow, B-Blue, G-Green, WWhite, YO-Yellow Orange. 1. These products are only suitable for connection to a UL Listed or Recognized maximum Class 2, 12 V DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 circuit limits. 3. Class 2 LED module, OTH-308X10x18-01 Series When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. Each module is rated 0.2A. 4. These products are suitable for use in dry, damp or wet locations. 5. These products are not required to be enclosed or protected from the weather.

MEGAPULL INC 161 TROLLINGWOOD LANE MORRISVILLE, NC 28117

E318039

Class 2 LED Module, Cat. No. AABBCCEEFFG MMDDYY series, where AA may be FL, DL or RE, where BB may be CX, LK ,LR LC, NI, AV, OS, AO, AB, CR, LU, SE, or OT, where CC may be BL, RE, GR WH, CW, NW, WW, CY, RB, RO, AM or OT, where EE may be WB, or NB, where FF may be SP or DP, where G may be any number from 0 to 9, where MMDDYY may be may be any number combinations from 000000 to 999999. 1. For connection to the Class 2 output of a Listed or Recognized Component power source rated 15 Vac or 36Vdc maximum. Other applications require additional evaluation. 2. Class 2 LED Modules, Cat. No. No. AA01BBCCEEFFG MMDDYY series are each rated max. 5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are suitable for use in dry, damp and wet locations when rated 15 Vac or 30Vdc maximum. Products that are rated maximum of 36 VDC are suitable for dry and damp locations only. 4. These products are not required to be enclosed or protected from the weather in the end product. 5. These products may be secured in place in the end product by any means available. 6. When these products are used in applications other than signs or outline lighting, the need to conduct a temperature test shall be considered.

MILLIKEN INDUSTRIES 101 S MCCALL RD ENGLEWOOD FL 34223

Sign face tensioning systems, designated "Matched Component Staple System". 1. Suitable for use in outdoor signs.

E187149

NEO-NEON INTERNATIONAL LTD. 2ND FL, ROOMS 1 & 8 CHINA HONG KONG CITY TSIM SHA TSUI, 33 CANTON RD KOWLOON, HONG KONG

E252578

LED String System Cat. Nos. LED vertical PCB, Model LC-BL-300-12V-**. LED vertical PCB, Model LC-BL-300-12V-**. LED horizontal PCB, Model LC-BL-110S-12V-**. LED horizontal PCB, Model LC-BL-110S-12V-**. LED horizontal PCB string, Model LC-BL-24V-6-TYPE A-**. LED horizontal PCB string, Model LC-BL-24V-6-TYPE A-**. LED horizontal PCB string, Model LC-BL24V-6-TYPE B-**. LED horizontal PCB edge lite, Model LBLU-10x88-6-12V-**. LED horizontal PCB edge lite, Model LBLU10x88-6-12V-**. LED vertical flex PCB, Model LBLU(FX)-V-6.25\'-12V-**. LED flexible listel light, Model FLF-99-1M-12V-**. LED tubes, Models LN-MN-300-24V-M(W), LN-MN-600-24V-M(W), LN-MN-1000-24V-M(W), and LED tube controller, Model SRC181-24V. LED back light string, Model LBLS-PL-2P-12V-**, LBLS-AL-2P-12V-**, and LF(V)-A-1-12V-**. LED high power back light, Model LBLS-AL-CC350-**, and LBLS-PL-CC350-**. LED linear flex, Model LBLU(FX)-H-10x420-10-24V-**. ** can be replaced by additional letters or numbers to indicate color. 1. LED's may be supplied by a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2, 24 VDC maximum output power source. 2. LED's were evaluated for connection to a UL Listed or Recognized Component Sign Accessory - UYMR2, Class 2 source. 3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limiting requirements. 4. These products are not to draw a total wattage greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 5. Certain products described in this section may be cut into segments through a cutting line provided on the printed wiring board. No other cut across the board is permitted. 6. Units may be provided with UYMR2, 3M type 4950 double sided adhesive tape. LED Outline Lighting, Rectifier for 6VDC and 12V DC Class 2 Circuit, Model No. MLF(H)-2W-5X8*a*b*c, may have suffixes *a, b or c. a = 3Ft - 132Ft. *b = 6Vdc or 12Vdc. *c = R, Y, W, G, B (LED lamp color). Note: 3Ft - 120Ft for 6V DC, 3Ft - 132Ft for 12VDC 1. These products are only suitable for connection to a UL Recognized (UYMR2) Class 2 Power supply with a continuous output of 6 Vdc or 12 Vdc.

50

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

2. These products may be connected to a 6V or 12 V AC, UL Recognized (UYMR2) Class 2 power source when provided with optional rectifier. 3. These products are rated to draw 4.5 Amps at 12Vdc at a 132Ft maximum and 4 Amps at 6 Vdc at 120Ft maximum. Each unit shall be connected so as to not exceed the output current and power rating of the power supply. 4. These products, when connected to a UL Recognized (UYMR2), Class 2 Power supply with a continuous output of 6 Vdc or 12 Vdc, are suitable for installation in wet, damp and dry locations. 5. These products described in this section may be cut into segments only through a cutting mark symbol provided on the LED strip. 6. Units may be provided with UYMR2, 3M type 4950 double-sided adhesive tape. Tape must be utilized per UYMR2 "Conditions of Use" as defined in the Sign Components Manual. 7. Mounting Clips may be used on walls, pillars doorframes or the like places. LED Modules, Component Sign Accessories, Class 2 Powered LED Module , Cat. No. LP-PIXDOT-Ø30-5V or LS-DIA34-5VM, where each Cat. No. may be optionally followed by a letter from A to Z or by a number from 0 to 9. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 Powered LED Module, cat. no. LP-PIXDOT-Ø30-5V or LS-DIA34-5V-M is each rated max. 3.6 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product.

NEON TECH 1965 PLAZA REAL OCEANSIDE, CA 92056

E307713

Class 2 LED Power Supply, Model LT380. 1. This power supply has a Class 2 output that has been evaluated to Class 2 output requirements for dc circuits. 2. This product with Class 2 outputs are suitable for use only in dry locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure.

NEXON CO LTD E318820 24-26 SIKSA-DONG ILSANDONG-GU GOYANG-SHI, GYEONGGI-DO 410-050 REPUBLIC OF KOREA

Class 2 LED Module, Cat. No. NXF-0YMZ Series, where Y may be replaced with 02 or 06; and Z may be replaced with B, R, PG, W or Y. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Vac, 30 Vdc, or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 15 Vac or 30 Vdc. 3. Class 2 LED modules, Cat. no. NXF-0YMZ Series are each rated max. 1.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product. 6. These products may be secured in place in the end product by any means available.

NU POWER ASSOCIATES INC. SUITE 110 4710 W DEWEY DR LAS VEGAS, NV 89118

E238096

Class 2 LED Power Supplies, Cat. Nos. SLD45-108V-XX, SLD45-110V-XX, SLD45-112V-XX, SLD45-115V-XX, SLD45-118VXX, SLD45-121V-XX, SLD45-124V-XX, SLD60-112V-XX, SLD60-115V-XX, SLD60-118V-XX, SLD60-121V-XX, SLD60-124V-XX. 1. These power supplies have a single output that complies with Class 2 output requirements. 2. Power supply, Model series ­FC and ­FE are suitable for use in dry, damp, and wet locations. Model series -FT is suitable for indoor use. Model series ­FT is suitable for wet and damp location when provided with a UL Listed NEMA Type 3 enclosure. 3. Power Supply, Model series ­FC and ­FE are provided with aluminum enclosure that complies with enclosure requirements. 4. Power supply, Model series ­FT shall be provided with a suitable enclosure to cover terminals. Class 2 LED Illumination Module, Models SLD60-xyyz-FC Series, where x can be 1 or 2; yy can be 05, 06, 08, 10, 12, 15, 18, 21, 24 or 48; and z can be C, D, E or F. 1. These power supplies have a maximum of two Class 2 outputs. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. Power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings. 5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product. Class 2 LED Illumination Module, Model SLD120-xyyz-FC Series, where x can be 2; yy can be 08, 10, 12, 15, 18, 21, 24, 27, 36 or 48; and z can V.

51

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

1. These power supplies have maximum of two Class 2 outputs. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations, except models SLD120-236V-FC and SLD120-248V-FC are suitable for use in dry and damp locations due to output voltages above 30 V dc. 3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 4. When used in wet locations, each unit shall be provided with listed (QCRV) and CN 1/2 inch liquid tight conduit fittings.

NUDO PRODUCTS INC 1500 TAYLOR AVE SPRINGFIELD IL 62703

E180252

Structural panels, consisting of a plywood core faced on both sides with sheet aluminum, Type Nu-Alum. 1. The panels may be used as part of a sign body but shall not be relied upon as an electrical enclosure. 2. Any parts other than neon standoffs or small decorative parts secured to the panel must be secured by means of through screws or bolts, nuts and washers. 3. The backing is not to be considered as providing a weatherproof enclosure, therefore, all internal sign components shall be suitable for outdoor use. 4. All heat producing components such as ballasts, fluorescent lamps and starters, transformers, electrodes and the like shall be spaced at least 1 inch from the structural backing. Structural panels, consisting of a polypropylene core faced on both sides with sheet aluminum, Type Aluma Core. 1. The structural panel may be employed as external decorative faces and for the support of complete electrical enclosures. 2. The structural panel is not to be used to enclose bare live parts or wiring. 3. Enclosures, plastic faces, and moldings may rely upon the structural panel for support. These components are to be reliably secured to the panel. 4. Any parts other than neon standoffs or small decorative parts must be secured to the panel by bolts, nuts and washers. The minimum washer diameter is 7/16 inch.

ODECO ELECTRONICA SA CARR N-II KM 636 08911 BADALONA, BARCELONA SPAIN

E313829

Sign LED Module Panel Cat. Nos. LiveAd WWWxYYY-ZZ Series, where WWW and YYY may be replaced with any combinations of digits from 000 to 999 incl. and ZZ may be replaced with 14,15,16,18 or 22. 1. These components should be installed in accordance with the manufacturer's instructions. 2. These devices are to be used in accordance with the ratings and load types as specified below. Catalog Number LiveAd 160x048-16 Operating Voltage (V) Input V ac 120/208 5 Max Input Current Max. Output Vdc (rms) 8 Type Load LED

3. The suitability of supply connections shall be considered in the end product. 4. The suitability of Ground Continuity Test and Leakage Current Test shall be considered in the end product. 5. These components are not provided with drain holes. The need to have drain holes shall be considered in the end product. 6. The Exclusion of Water Test was conducted on the entire product. In the end product conducting the Exclusion of Water Test shall be considered on the supply connection part of the product. Video Converter Cat. Nos. "Video Converter" (LiveAd 3G). 1. These components should be installed in accordance with the manufacturer's instructions. 2. These devices are to be used in accordance with the ratings and load types as specified below. Catalog Number "Video Converter" (LiveAd 3G) Input V ac 120/240 Max Input Current (rms) Output Vdc 1 12 Max. Output Current, Amps 7 Type Load LED

4. The need to conduct a Leakage Current Test shall be considered in the end product. 5. These components have been evaluated for use in indoor dry location use only. 6. This product was tested for use at room ambient temperature of 25°C. At higher ambient temperatures consideration for conducting temperature shall be consider by the end product requirements.

OPTOENGINEERING PO BOX 52067 TULSA, OK 74152

E215877

LED System fro use on Class 2 Circuits Cat. Nos. CL-SS and CL-RS, may or may not be followed by suffix. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limiting requirements. 3. These products are suitable for use in dry, damp and wet locations. 4. These products are not required to be enclosed or protected from weather. 5. When a transformer, R/C, XOKV2, Product Unlimited Corp., and rectifier rated 100 Volts and 25 Amps are provided, they are to be enclosed with an enclosure not smaller than 102 mm wide, 152 mm long, 102 mm high. 6. Foam board has not been evaluated to be suitable as an enclosure.

52

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

7. When Transformer Model Number LED120A0012V50F by Philips-Advance Transformer Co. is provided in a portable sign, the maximum number of component led array drivers shall be 4.

OSRAM SYLVANIA INC 54 CHERRY HILL DR DANVERS, MA 01923

E258264

Class 2 LED Illumination Module, Cat. Nos. OS-LM01A-X, OS-LM01A/X, OS-LM03A-X and OS-LM03A/X , where X may be replaced with where X may be replaced with any letters of alphabet A to Z or any number from 0 to 9 or combination of letters and numbers. 1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component ­ Sign Accessory. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the maximum secondary or output current rating of each Class 2 circuit. The following identifies the rating to be used in calculating the maximum number of units per circuit. Load (Amps) Cat No. Watts OS-LM01A-A OS-LM03A-Y 0.40 A 0.40 A 4.0 W 4.0 W

4. Cat No. OS-LM03A-Y are provided with wire soldered on the printed wiring board for connection. 5. These products are suitable for use in dry, damp and wet locations. 6. These products are not required to be enclosed or protected from weather. Class 2 LED Illumination Module, Cat Nos. OS-LM10A-X, OS/LM/10A/X, OS-LM11A-X, and OS/LM11A/X, where X may be replaced with any letters of alphabet A to Z or any number from 0 to 9 or combination of letters and numbers. 1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component ­ Sign Accessory. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the maximum secondary or output current rating of each Class 2 circuit. The following identifies the rating to be used in calculating the maximum number of units per circuit. Load Cat No. (Amps) Watts OS-LM10A OS-LM11A 0.05 A 0.04 A 1.2 W 0.4 W

4. Cat No. OS-LM10A may be daisy chained together in the form of a reel. 5. These products are suitable for use in dry, damp and wet locations. 6. These products are not required to be enclosed or protected from weather. Class 2 LED Illumination Module, Cat No. "HF2Chain/36/W3/865-12ft". 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED Lighting Assemblies, Model "HF2Chain/36/W3/865-12ft" is each rated max. 53 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Array Drivers, Cat. No. OT25/120/10, OT50/120/10, OT75/120/24 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 5. The drivers are intended for installation inside an electrical enclosure. 6. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. 7. The drivers are suitable for dry location use only. Class 2 LEDs, Cat. No. OS/DS6/W2-847 and OS/DS12/W2-847. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LEDs Cat. Nos. OS/DS6/W2-847 and OS/DS12/W2-847 are each rated max. 17 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Modules, Cat. No. OS/DC36/W2-865. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less.

53

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED Module Cat. Nos. OS/DC36/W2-865 is each rated max. 60 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Power Supplies, Cat. No. Optotronic OT20/120-240/24S. 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 50°C. 3. The drivers are intended for installation inside an electrical enclosure. 4. The drivers may be mounted inside an electrical enclosure with 1 inch spacing end to end and 4 inch spacing side to side. 5. The ground connection is suitable as the equipment ground for a sign connected to a maximum 15A branch circuit. Separate provision for sign grounding must be provided when connected to a 20 A branch circuit. 6. The drivers are suitable for dry or damp location use. Class 2 LED Illumination Module, Cat Nos. BL02LT-A1, BL02ST-A1, BL02STB1, BL02ST-O1, BL02ST-S1, BL02ST-T2, BL02ST-W2-865 and BL02ST-Y2. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated greater than 12 V. 3. Class 2 LEDs Cat. Nos. BL02LT-A1, BL02ST-A1, BL02STB1, BL02ST-O1, BL02ST-S1, BL02ST-T2, BL02ST-W2-865 and BL02ST-Y2X are each rated max. 23 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product. Class 2 LEDs, Cat. No. OS-LM10L-XXX, where XXX is any alphanumeric combination denoting color. 1. These products are only suitable for connection to a Class 2 24 VDC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED Module Cat. Nos. OS-LM10L-XXX are each rated max. 24 VDC, 2.25 A, 54 Watts per string. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at max 30 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. Class 2 LEDs, Cat. No. OS-DT6-W2-XXX, where XXX is any alphanumeric combination denoting color. 1. These products are only suitable for connection to a Class 2 350mA constant current power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED Module Cat. Nos. OS-DT6-W2-XXX are each rated max. 7.2 Watts per unit 6 units in a string. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 30 Volt DC or 15 Volt AC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Lighting Assemblies, Cat. No. PROMINENCE Contour Lighting Assemblies", "PROMINENCE TM Stall Star", "PROMINENCE TM Blue 2\' Radius Tube. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 Lighting Assemblies, Model "PROMINENCE Contour Lighting Assemblies", "PROMINENCE TM Stall Star" and "PROMINENCE TM Blue 2' Radius Tube"series is each rated max. 75 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. Class 2 LEDs, Cat. No. BACKlight2G/YYY/BL04ST/XXX, where YYY may be either any alphanumeric combination or optional and XXX is any alphanumeric combination denoting color or characteristic of the LED. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED Module Cat. Nos. BACKlight2G/YYY/BL04ST/XXX is each rated max. 38 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. Class 2 Lighting Assemblies, Cat. No. "LINEARlight POWER FLEX", model no. LM10P/W3-xxx where xxx may be replaced with any letters of alphabet A through Z and any numbers 0 through 9 or combination of letter and numbers. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 Lighting Assemblies, "LINEARlight POWER FLEX", model no. LM10P/W3-xxx is each rated max. 75 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.

54

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product. Class 2 LEDs, Cat. No. OS-DT6-Class 2 LED Illumination Module, DRAGONPUCK OS/DP3/XX Series and HFDisk/3/W2-XX, where XX may be replaced with any letters of alphabet A through Z and any numbers 0 through 9 or combination of letter and numbers. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED Illumination Modules, DRAGONPUCK OS/DP3/XX Series and HFDisk/3/W2-XX are each rated max. 7.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Array Drivers, Cat. No. OT 6/100-120/10 CE, and OT 6/100-120/24 CE. 1. The suitability of the mounting means shall be determined in the end-use product. 2. OT 6/100-120/10 CE and OT 6/100-120/24 CE employ a R/C (OBJY2) Class B(130)ins. system and have been evaluated at an elevated ambient of 50° C. Temperature testing is required in the end product and the ambient cannot exceed 50°C. 3. Leakage testing shall be performed in the end product if installed in a cord connected sign. 4. A suitable Enclosure with a conduit connection means shall be provided in the end-product. 5. These components are intended for Dry and damp Locations Only. Class 2 LEDs, Cat. No. Model HF2-STICK-XB. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less. Suitability for use with a power supply that does not comply with Class 2 requirements has not been determined. 2. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 3. These products are suitable for use in dry, damp and wet locations. 4. These products are not required to be enclosed or protected from the weather in the end product. LED Power Supplies, Cat. No. OT 9/100-120/350E and OT 8/100-120-24E. 1. The suitability of the mounting means shall be determined in the end-use product. 2. Model OT 9/100-120/350E has been evaluated at an ambient of 50° C. 3. The input/output connectors have not been evaluated for field connections and are only intended for connection to mating connectors of internal wiring inside the end-use product. 4. Leakage test shall be performed in the end product. 5. A suitable Fire and Electrical Enclosure shall be provided in the end-product. LED Power Supplies, Cat. No. OT 75/120-277/24E and OT 50/120-277/10E. 1. The suitability of the mounting means shall be determined in the end-use product. 2. Input supply means is provided by minimum 6" length of leads intended for field wiring. Acceptability of this construction is to be determined as part of the end product evaluation. 3. The acceptability of the output leads shall be determined in the end product. 4. Model OT 50/120-277/10E has been evaluated at an ambient of 60° C. 5. Model OT 75/120-277/24E has been evaluated at an ambient of 50° C. 6. Model OT 75/120-277/24E has been additionally evaluated at an ambient of 60°C, when R/C (OBJY2) Class F, type KIS-ME02 by Kaschke is utilized. 7. Grounding lead shall be crimped between top and bottom of enclosure case. This ground is for functional grounding purposes only and shall not be relied upon for safety grounding. LED Power Supplies, Cat. Nos. OT 75/120-277/24S, OT 50/120-277/10E. 1. The suitability of the mounting means shall be determined in the end-use product. 2. Input supply means is provided by minimum 6" length of leads intended for field wiring. Acceptability of this construction is to be determined as part of the end product evaluation. 3. The acceptability of the output leads shall be determined in the end product. 4. Model OT 50/120-277/10E has been evaluated at an ambient of 60° C. 5. Model OT 75/120-277/24E has been evaluated at an ambient of 50° C. Model OT 75/120-277/24E has been additionally evaluated at an ambient of 60°C, when R/C (OBJY2) Class F, type KIS-ME02 by Kaschke is utilized. 6. Grounding lead shall be crimped between top and bottom of enclosure case. This ground is for functional grounding purposes only and shall not be relied upon for safety grounding. LED Power Supplies, Cat. Nos. OT 9/100-120/350E, OT 08/100-120-24E. 1. The suitability of the mounting means shall be determined in the end-use product. 2. Model OT 9/100-120/350E has been evaluated at an ambient of 50° C. 3. The input/output connectors have not been evaluated for field connections and are only intended for connection to mating connectors of internal wiring inside the end-use product. 4. Leakage test shall be performed in the end product. 5. A suitable Fire and Electrical Enclosure shall be provided in the end-product

55 OSRAM SYLVANIA INC 54 CHERRY HILL DR DANVERS MA 01923

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

E220096

LED Power Supplies, Cat. No. 0T3/120-240/350, OT240/120-240/24/CH3, OT96/120-277/24, OT240/120-240/24/CH, OT240/120-240/12/CH, OT25/120-277/700E, OT20/120-240/10E. 1. Power supply has maximum three Class 2 outputs. Each output of these power supplies have been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 4. When not marked for indoor use only, all units shall be provided with liquid tight fittings on the primary and secondary circuits. LED array drivers, Models OT25/120/10, OT50/120/10, and OT75/120/24. 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The supply terminals and connectors are suitable for factory wiring only of solid or tinned stranded No. 18 AWG conductors. 3. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 40°C. 4. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 5. The drivers are intended for installation inside an electrical enclosure. 6. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. 8. The drivers are suitable for dry location use only except the drivers OT50/120/10, and OT75/120/24 are suitable for both dry and damp location use. 9. The Model OT25/120/10 has a Class 2, 0-10 V dc output for dimming purposes. Two output terminals are provided for connection to an optional dimmer control.

PCH INTERNATIONAL LTD 22ND FL CITIC TOWER 1093 SHENNAN RD CENTRAL SHENZHEN, GUANGDONG 518031 CHINA

Class 2 LED Modules, Designated "LED Light Assembly Panel". 1. These components are to be installed in accordance with the manufacturer's instructions. 2. These devices are rated as specified below. Catalog Number "LED Light Assembly Panel" (Input-Output) Operating Voltage 24 V ac, 480 mA Type Load LED

E309814

3. An electrical enclosure needs to be provided in the end product. 4. No tests have been conducted on these components and as such, end product testing should be considered. 5. The suitability of input leads and connector needs to be considered in the end product. 6. These panels have only been evaluated for use when connected to a Class 2 power source. 7. These products have not been evaluated for use when connected to power

PERMLIGHT INC 422 W 6TH ST TUSTIN CA 92780

E213411

Class 2 LED Illumination Cat. Nos.700 Series, 752 ("Twister\'r"), 760-2, 760-3, 765-4, 750-5, 750-9, 711-2, 780 Series, TINY2, PX Series. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. No more than 80 illumination boards are to be interconnected together and supplied by a single Class 2 circuit. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather. Class 2 LED Illumination, Model No. 711-18DL. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Illumination, 711-18 DL module is rated 60 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit. 4. Cat. No. 711-18 DL modules are provided with R/C wire soldered on the printed wiring board for connection. 5. These products are suitable for use in dry, damp and wet locations. 6. These products are not required to be enclosed or protected from weather. Class 2 LED Illumination, Model No. Elblanco/Delta Light PML900 Series. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source.

56

2.

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Illumination, "Elblanco/Delta Light" PML900 Series are each rated max. 10 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather. Photocell, Model PL746-TPC "Photocell". 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Illumination, "Photocell" PL746-TPC is rated max. 60 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather. LED Power Supply with Class 2 outputs, Cat. Nos. 60-12D, 60-012DC, 60-012DC-DIM, 60-12D-U, 37-007DC-DIM, 37007DC. . 1. These products are intended for use only in applications that comply with the requirements of the end product. 2. These products are suitable for use only where contained in an end use product compartment that is suitable as an electrical enclosure. 3. These products are suitable for use only where made inaccessible to contact by users during user maintenance while energized. 4. When marked as suitable for use outdoors, these products are to be installed where protected from rain, snow and water spray by water shield or sign body. 5. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at least 150 mm (6 in) inside. LED Power Supply with Class 2 outputs, Cat. Nos. 250-D-C 1. These products are intended for use only in applications that comply with the requirements of the end product. 2. These products are suitable for use only where made inaccessible to contact by users during user maintenance while energized. 3. When marked as suitable for use outdoors, these products are to be installed where protected from rain, snow and water spray by water shield or sign body. 4. These products shall have conductors entering, leaving or residing in the wiring compartment or junction box extending at least 150 mm (6 in) inside. LED Power Supply with Class 2 outputs, Cat. Nos. 250-D. 1. This LED Power Supply is suitable for use in indoor or dry locations only. 2. This power supply is suitable for use only with or on portable LED signs. 3. This power supply has 4 outputs each of which comply with Class 2 circuit limitation requirements. Each output circuit is not to be connected in series or in parallel directly or by interconnection of any part of the load on each circuit. 4. The attachment plug on the end of the power supply cord is not to be removed. Class 2 Letter Signs Cat. Nos. Model 800 Series. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Illumination, "Photocell" PL746-TPC is rated max. 60 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit. 4. These products are suitable for use in dry, damp and wet locations. 6. These products are not required to be enclosed or protected from weather. Class 2 LED Illumination Module, Cat Nos. Class 2 LED Module, "PZ" Series. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated greater than 12 V. 3. Class 2 LEDs "PZ" series is rated max. 6 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product. Class 2 LED Illumination, Model No. Cat. Nos. 737 ("Twister Nano"), 747 ("el Plato"), 777 ("Twister Nitro"), 787 ("Twister Halo") Series. All catalogue numbers may be followed by WWXYZ; where WW may be replaced with any letters of alphabet AA through ZZ; X may be replaced with any letter of alphabet A through Z or may be left blank, Y may be replaced with any letters of alphabet A through Z or may be left blank and and Z may be replaced with any letters of alphabet A through Z or may be left blank. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 15 V. 3. Class 2 LED Modules, Cat. No. 737 ("Twister Nano"), 747 ("el Plato"), 777 ("Twister Nitro") and 787 ("Twister Halo") series are each rated max. 7.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Class 2 Power Supply, Cat. Nos. 60-12D-A.

57

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure.

PHILIPS LIGHTING B V E211810 KANTSINGEL 24 5349 AJ OSS, THE NETHERLANDS

LED power supply with Class 2 outputs, Cat. No. Model 9137 006 208 1. Model 9137 006 208 is rated for a 100-240 Volts, 50/60 Hz, 25 Watt input and a 24 V DC, 0.83 amp, 20 Watt output. 2. These components are intended for use in dry locations only when not potted. When potted, they are suitable for use in damp locations. 3. These power supplies need to be installed in an enclosure with a means for connection to conduit. 4. A Temperature Test is not required of the power supply when installed in an enclosure having dimensions greater than 13.5 by 6 by 4 inches. When installed in a smaller enclosure and a Temperature is required, the maximum temperature on the output transformer by thermocouple is 90°C. 5. The Class 2 output of these LED power supplies are acceptable for use in a damp and wet location. LED power supply with Class 2 outputs, Cat. No. Model 913710052466 1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp locations. 2. These power supply needs to be installed in an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110° C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location LED power supply with Class 2 outputs, Cat. No. Model 9137006209 1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp locations. 2. These power supply needs to be installed in an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110° C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location

PHILIPS LIGHTING SSL(CANADA) E246878 7700 RIVERFRONT GATE BURNABY, BC V5J 5M4 CANADA

Class 2 LED Module, LightScript Series. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp locations. 5. These products are not required to be enclosed or protected from weather. LED power supply with Class 2 outputs, Cat. No.PSE. 1. These components are intended for use in dry locations only when not potted. When potted, they are suitable for damp locations. 2. These power supply needs to be installed in an enclosure with a means for the connection to conduit. 3. When a Temperature Test is required of the power supply installed in an enclosure because the enclosure measures less than 13.5 by 6 by 4 inches, the maximum temperature on the output transformer by thermocouple is 110° C. 4. The output of these LED power supplies with Class 2 are acceptable for use in a damp and wet location 6. Where stranded leads are used to terminals, the ends must be tinned.

PHILIPS SOLID-STATE LIGHTING SOLUTIONS INC.

E243468

3 BURLINGTON WOODS DR BURLINGTON, MA 01803

LED Outline Lighting, iColor Accent Powercore Series, Model Nos. 123-000010-00, 123-000010-01, 123-000010-02, 999000189-00, 999-000190-00, 999-000191-00, 999-000192-00, 999-000193-00, 999-000194-00, 999-000210-00, 999-000211-00, 999-000212-00,999-000214-00, 999-000214-01, 999-000214-02, 999-000214-03, 999-000214-04, 999-000214-05, 999-00021406, 999-000214-07, 999-000214-08, and 999-000214-09. 1. These products are only suitable for inter-connection to iColor Accent Powercore system. 2. Cable for inter-connecting units are not to draw more than 7.0A. 3. These products are suitable for use in dry, damp and wet locations. 4. Maximum run of 100 feet of outline lighting. LED Leader cable , Model No. 108-000028-01. 1. These products are only suitable for the interconnection of the iColor Accent Powercore Series system to the Data Enabler EO. 2. These products are suitable for use in dry, damp and wet locations. 3. Maximum length of cable and outline lighting units is 100 feet accumulative. 4. The Gland and Strain Relief is to be installed with the Data Enabler EO according to the instructions in the Data Enabler EO user guide.

58

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

PHILIPS SOLID-STATE LIGHTING SOLUTIONS INC.

E312392

3 BURLINGTON WOODS DR BURLINGTON, MA 01803

LED Data Enabler Cat. Nos. Cat. No. 106-000003-06. 1. These components should be installed in accordance with the manufacturer's instructions. 2. These devices are to be used in accordance with the ratings and load types as specified below. Catalog Number 106-000003-06 (Input-Output) Operating Voltage 100 V -240 Vac Input Current (A) A Type Load LED

3. These products may be provided with pigtail leads extending at least 150 mm (6 in) inside a wiring compartment or junction box. The final installation should be evaluated in the end use application. 4. Spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 5. Spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 6 inches.

PLASTOLED SYSTEMS SUITE 150 9025 BALBOA AVE SAN DIEGO, CA 92123

E257957

Class 2 LED Illumination Cat. Nos. Series: X-2-4 (X-508-4), X-1.5-4 (X-381-4), X-2-2 (X-508-2), X-1-2 (X286-2), XT-2-4; "Halo LED" Series: HX-2-3, HX-05-2, HX-.75-3, where X may be A, R, G, B, W or Y; "Single Stroke Letters" Series: XL-1-K-L; "Double Stroke Letters" Series: XL-2-K-L, where X may be R, G, B, W or Y; K may be any of alphabet letters from A to Z incl. or numbers from 0 to 9 incl. or symbols and L may be numbers 5, 7 or 10. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Illumination. XLP is a series of 3 LEDS that draws 350mA. A total of only 14 of these units can be connected to a Class 2 output circuit (based on 5 amps max.). SLP is a series of 2 LEDSthat draws 50 to 70mA. A total of only 70 of these units can be connected to a Class 2 output circuit (based on 5 amps max.). 4. Class 2 LED Illumination, these products are provided with R/C wire soldered onto the printed wiring board for connection in series. 5. When connected to a Class 2 circuit, 12 volt output supply, these LEDs are suitable for installation in wet locations, damp, and dry locations. 6. These products are not required to be enclosed or protected from weather.

P N P INC, DBA AMERICAN SUN CONTROL - AWNINGS 925 MCFARLAND 400 BLVD ALPHARETTA GA 30004

Sign Face Tensioning Systems, designated "Fabri-Frame Fabric Framing System". 1. Suitable for use in outdoor signs.

E199185

POLYBRITE INTERNATIONAL 1751 W DIEHL RD. SUITE 110 NAPERVILLE, IL 60563

E303143

Class 2 LED Module, Cat. No. "Modular Lighting System Module", designated Models MLS-XK-L Series and MLS-HPXK-L, where X may be replaced by A, B, G, R, RO, W, WW and Y; K may be replaced by any digits between 0-9 incl. and L may be replaced by any number between 10-50 incl. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits. 3. Class 2 LED Modules "Modular Lighting System Module", MLS-XK-L Series and MLS-HPXK-L Series are each rated max. 7.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

POWER LINK ELECTRONICS CO INC

E306782

59

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

252 S 5TH AVE CITY OF INDUSTRY, CA 91746

Class 2 LEDs Cat. Nos. LEDMX-KN Series, where X may be replaced with any letters of alphabet A through Z or blank; K may be replaced by R, A, Y, B, G or W and N may be replaced with any numbers 0 through 999. 1. These products are only suitable for connection to a Class 2 power source, rated max 15 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED Module Cat. Nos. M LEDMX-K series is each rated max. 7.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product. LED power supply with Class 2 outputs, Cat. No. SPS-X0-12, where X is 4, 6 or 9. 1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry and damp locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product. 5. The suitability of grounding connection shall be determined in the end-use product.

PWM GMBH & CO KG KOLNER STR 120 51691 BERGNEUSTADT, GERMANY

E188273

Sign controller , Model "E-Box-XX" Series, where XX may be any number from 0 to 9 or any letter of alphabet from A to Z or combination of numbers and letters. 1. These components should be installed in accordance with the manufacturer's instructions. 2. These devices are to be used in accordance with the ratings and load types as specified below. (Input-Output) Operating Voltage (V) Input Output (DC) Catalog Number Max Output Current (rms) Type Load (AC) E-Box-45 100 15 4.75 LED E-Box-45 120 15 1.95 LED E-Box-45 240 15 3.83 LED 3. These components are not provided with suitable enclosure or sign body. The need for a electrical enclosure should be considered in the end product. 4. Spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 5. Spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 6 inches. 6. The suitability of output wiring shall be suitable for use with Class 1 wiring system. 7. The output of these components exceeds Class 2 limits such that it is not acceptable for use with products designated on for use when connected to a Class 2 circuit. LED Modules, "LED Digits", Model PSDU-XX-YYY, where XX may be replaced with any letters of alphabet from A to Z or with numbers from 00 to 99 or combination of letters and numbers; YYY may also be replaced with any letters of alphabet from A to Z or with numbers from 000 to 999 or combination of letters and numbers. 1. Wiring and means of connection between modules shall be investigated in the end product requirements. 2. No tests have been conducted on these components and as such, end product testing should be considered 3. These modules units are not provided with suitable enclosure or sign body. The need for a electrical enclosure should be considered in the end product. 4. These components are to be installed in accordance with the manufacturer's instructions. 5. These Modules are acceptable for use on a Class 2 circuit and when powered by other than a Class 2 circuit, end product requirements, such as enclosure and accessibility, should be applied.

REGAL SUPPLY 111 E. 10th AVE. NORTH KANSAS CITY, MO 64116

E248921

Aluminum reinforced sign face trim, Cat. Designations SnakeEye, SideWinder, DiamondBack, Trinity, T2, Glory I, Glory II, and PowerHouse. Colors are clean white, blue, green, red, and amber abbreviated Wht, Blu, Grn, Red, and Amb, respectivelyType Plasco trim. 1. The number and arrangement of the LED boards connected to a Class 2 power supply shall not exceed the output wattage/current rating of the power supply. Each LED board is rated as follows:

Model

Voltage-DC Watt/ma usage for each color

60

SIGN COMPONENTS MANUAL (SAM)

Wht Snake Eye Side Winder Diamond Back Trinity T2 Glory I Glory II Power 12 12 12 12 12 0.5/42 1.0/83 1.1/92 2.2/183 0.5/42 1.1/92 0.5/42 1.1/92 0.4/33 0.7/58 0.4/33 0.7/58 12 0.5/42 12 0.5/42 0.5/42 0.5/42 0.4/33 0.4/33 12 0.5/42 Blu Grn Red Amb -

April 21, 2008

2. 3.

4.

House The LED boards are intended only for connection to the 12 VDC output of a Class 2 power supply. The LED boards are secured to the sign housing by tape. No further evaluation is required unless there are heat producing components or uninsulated electrical terminals or parts in the same compartment. Alternatively may be secured by screws in accordance with instructions. The sign housing of a permanently wired sign shall be grounded to the supply connection ground. E252627

RELUME TECHNOLOGIES TM 33844 STERLING PONDS BLVD STERLING HEIGHTS, MI 48312

Class 2 LED Module Cat. Nos.SILVER CIRCUIT. 1. Portable LED signs may be used with Listed or R/C Class 2 power supplies, used in accordance with the conditions of acceptability. Permanently wired LED signs are used with R/C (UYMR2) LED drivers used in accordance with their conditions of acceptability. These products are only suitable for connection to a 24 volt maximum DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp locations. When the maximum output of the power supply is 24V continuous dc or 12.4V peak for dc interrupted at a rate of 10 to 200Hz, the products may be installed in wet locations. 5. These products are not required to be enclosed or protected from weather.

REVOLUTION DISPLAY SYSTEM INC. UNIT 10, 415 HORNER AVE. ETOBICOKE ON M8W 4W3, CANADA

E238704

Scrolling Sign Controller, Cat. No. RSC-6. 1. These devices should be used within their Recognized ratings as specified above. 2. These devices are intended to be mounted in an overall sign housing. 3. The controller can be used in enclosures with a minimum of 12000in3 of volume and with a watt density of 8W/in3. Scrolling Sign Controller, Cat. No. RMI. 1. This device is suitable for use in dry and damp locations. 2. This device is rated for a 120Vac supply and has an output suitable for controlling 120V ac, maximum 2 amps ballast and 2 amps Motor loads simultaneously. 3. This device is suitable for use only when installed within an end product enclosure that also serves to keep the unit from precipitation and makes live parts inaccessible. 4. This controller is suitable for installation in an enclosure having overall dimensions no less than 7 x 12 x 12 inches. Controller shall be installed min four inches from any heat producing component such as ballast or motor.

REYNOLDS METALS CO, DBA ALCOA CLADDING SYSTEMS 555 GUTHRIDGE CT NORCROSS, GA 30092

E311557

Structural Panels Cat. Nos. RB80, -100, -120, -160, -240 1. Suitable for use in dry, damp and wet locations. 2. Suitable for use in decorative and sign body applications only. 3. Suitable for use in component support applications. When threaded directly into the panels, screws shall be no smaller/finer than No 10. Suitability of smaller and/or finer screws shall be determined. 4. Rain tightness shall be determined in the end product. 5. Electrical spacings and bonding for grounding shall comply with the end product standard. 6. Suitable for use in terminating conduit in 3/8 in. or * in Trade Size. 7. A letter made from a structural panel shall have at least two points of support and shall have no point more than 10 in. from a point of support 8. These materials are rated 50*C, consideration will need to be given to end product thermal spacings from heat producing components or temperature test.

61

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

9. These materials are available as unpainted aluminum or pre-painted aluminum.

SABIC INNOVATIVE PLASTICS US L L C SPECIALTY COMPONENTS & PRODUCTS 1 PLASTICS AVE PITTSFIELD, MA 01201

E136722

Rigid sign face system, designated: Lexan S-10, S-30, MR101, SG, SGC, 903, MR-AC, SLG-305 and GE Lexan Sign Grade Sheet. All may be followed by additional letters and/or numbers. Rigid sign face for use in indoor electric signs to complete electrical enclosures, Lexan MR-10. 1. The mounting system must secure the sign face to the enclosure in such a way that the edges of the sign face are not exposed to the interior of the sign. This may be accomplished with channels, flanges or other suitable mechanical means. 2. Refer to the following table for applicable use temperatures of the materials. If a heat producing component such as electrode, transformer or ballast is located within 1 inch of these materials, a temperature test should be conducted in the end product. Mechanical w/ Impact °C 80 125 125 125 125 125 Mechanical w/o Impact °C 80 125 125 125 125 125

Material Designation MR-AC SG SGC S-10 903 S-30

Electrical °C 80 130 130 130 130 130

SLG-305 130 125 125 GE Lexan 130 125 125 Sign Grade Sheet 3. Marking - The following markings or equivalent shall be provided. Markings below shall be marked anywhere where readily visible during servicing. a. "Do not attempt to repair or service a damaged sign face, cable support, or high-voltage splice insulator. For servicing of this sign, contact _______________." (Blank to be replaced by Applicant's Company name, City and State.) b. "Replace only with ________, Type ________." (Blanks to be replaced by Applicant's Company name and material Type or designation.) c. "Danger - High Voltage - Disconnect Power Before Servicing." d. "Upon replacement of lamps, the electrode/GTO wire connection must be made mechanically secure by crimping or twisting, and wrapped with UL Listed thermoplastic tapes to a thickness of the GTO insulation." This marking shall be placed near the electrode/GTO connection. 4. Types S-10, 903, and MR-AC, are suitable for use as an enclosure when used indoors only, but may be subject to exposure to UV. 5. Types S-30, SG, SGC, SLG-305 and GE Lexan Sign Grade Sheet are suitable for use as an enclosure of an indoor or outdoor sign. 6. All materials must be min. 0.1 in. (2.5 mm) thick to comply as and to complete a sign enclosure. 7. The rigid sign enclosure materials have been investigated for the securement of conduit, electrode housings or the like; the rigid sign face material has not. 8. Type MR-10 and MR-101 are suitable only as a sign face to complete a sign enclosure for indoor signs. Decorative Translucent Film, designated ColorQuik 1. Suitable for use only with General Electric Co. Recognized Component (UYMR2) Enclosures and Rigid sign face systems, designated Lexan S-10, S-30, 903, SG or SGC. 2. Suitable for use when applied to the exterior surface of the Enclosures and Rigid sign face systems. Marking - Company name and system designation is marked on protective film provided over surface of material such that a piece dimensioned 2 ft by 2 ft min. will contain all required markings. System designation will be the same as material designation except may be followed by additional digits.

SHANGHAI JIATANG ELECTRONIC CO 511 JIATANG HWY JIADING 201807 SHANGHAI, CHINA

E242985

Channel letter LED Modules, Models SLS-1-X, SLS-2-X. 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component ­ Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12 V DC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit. The following identifies the rating to be used in calculating the maximum number of units per circuit. Load Max Cat. No. (mAmps) Watts

62

SIGN COMPONENTS MANUAL (SAM)

SLS-1-X 30 0.36 0.36

April 21, 2008

4. 5.

SLS-2-X 30 These products are suitable for use in dry, damp and wet locations. The weather enclosure does not require evaluation.

Channel letter LED Modules, Models UL-3-X where X may be replaced with any letters of alphabet A through Z or any numbers 0 through 9. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. Class 2 LED Illumination Module, model no. SU-3-X is each rated max. 1.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product.

SHEFFIELD PLASTICS 119 SALISBURY RD SHEFFIELD MA 01257

E146154

Rigid sign face system, designated: Makrolon followed by EN, GP, OP, PS, SL or SN, may be followed by additional characters. 1. The suitability of the securement system to prevent the entrance of water, which may contact live parts within a sign in outdoor sign applications, shall be determined. 2. The sign enclosure material must be used in a min thickness of 0.1 in (2.5 mm). All testing should be repeated if the thickness of the sheet is reduced to less than 0.1 in. 3. The mounting system must secure the sign face to the enclosure in such a way that the edges of the sign face are not exposed to the interior of the sign. This may be accomplished with channels, flanges, or other means. The sign face is intended to be secured by mechanical means. 4. These materials have a use temperature of 75°C. The need for a temperature test should be considered if heat producing components are present. No test is needed when a neon electrode or transformer is spaced 2 in min from the sign face. 5. When the material is relied upon for the mounting of the sign and/or sign components, the material shall be used in accordance with the following guidelines. a. All holes shall be cleanly drilled without surface cracking or crazing. b. The mounting means shall consist of threaded rods, bolts or the like with a min dia of 0.115 in and backed by a min 0.213 in nut (as measured across the flats). c. A max weight of 40 lbs may be applied for each threaded rod. d. For vertical mounting applications, the mounting means shall be positioned a min of 0.25 in (5.1 mm) from the edge of the mounting surface. For horizontal mounting applications, a min 0.5 in (12.7 mm) from the edge of the mounting surface. 6. These materials have been investigated for the securement of conduit, electrode housings or the like. The entire enclosure may not be constructed of these sign face materials. 7. A marking shall be provided inside the sign indicating that servicing or replacement of the sign face material must be done by the company which sold the sign. Marking - Company name and system designation is marked on protective film provided over surface of material such that a piece dimensioned 2 ft by 2 ft min will contain all required markings. System designation will be the same as material designation except may be followed by additional digits.

SHENZHEN TOP CENTURY OPTO-ELECTRONICS CO LTD TOP CENTURY INDUSTRIAL PARK WEITAI RD 1 BAIMANGAO INDUSTRIAL ZONE YINGRENSHI BAO'AN SHENZHEN, GUANGDONG 518000 CHINA

E311265

Channel letter LED Modules, Models SF-YL67-3. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED modules, SF-YL67-3", is rated max. 7.5 Watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations.

SIGN/LITE INC

E163602

63 1071 NW 53RD ST FT LAUDERDALE FL

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

33309

Channel letter and small sign lighting systems, Models BLH-579-1-6, BLV-579-1-6, BLE-579-1-6, BLH-13-1-6, BLV-13-1-6, BLE-13-1-6, BLH-846-1-6 (with or without Suffix "K"), and BLV-846-1-6 (with or without Suffix "K"). 1. The exposed leads must be enclosed in end-product. 2. Spacings of not less than 1/2 in. are to be maintained between the lampholder, live metal, or other parts that may be a source of heat or arcing, and decorative and structural parts other than glass. 3. The ballast is to be within an overall electrical enclosure. 4. The ballasts shall be located not less than 1 in. apart when arranged end-to-end, and not less than 4 in. apart when arranged otherwise. 5. Suitable for use in all locations.

SIGNALEX INC 5617 MCADAM RD MISSISSAUGA ON

E86197

CANADA L4Z 1N4

Flexible sign face Tensioning Systems, Flexible sign face tensioning hardware Cat. No. BSH-V-Frameless, BSH-V-SF, BSHCH-Frame, BSH-V-CH-Frame, Ret-Fit-V-Frameless, Ret-Fit-V-CH-Frame, 125 and 2050, Models RET1980, BSH1950, RET1960, self-hanging flexible vinyl face frames 125, 2050 and 2060, flexible vinyl retrofit face frames 135, 2750 and 2061. Frameless Retrofit 2760. 1. The suitability of the flexible sign face materials designated below and tensioning systems on outdoor signs to prevent entrance of water, shall be determined in the end-use application. 2. The suitability of the mounting to prevent bellowing of the flexible sign face material into the lamps and loosening of the tensioning hardware, shall be determined in the end-use sign application. 3. The sign face materials for use with this hardware and designated below (Item 6) shall comply with the external decorative face requirements of UL 48, particularly spacings to adjacent heat sources such as lamps, ballasts, etc. 4. These systems have not been investigated for use as a portion of an electrical enclosure. 5. When the flexible sign face materials are used with this tensioning system on a sign with any dimensions (length or width) in spaces greater than 6 ft, suitable braces should be employed to prevent the reduction of spacings from the face material to adjacent heat sources.

SIGNCOMP 3032 WALKER RIDGE NW GRAND RAPIDS, MI 49544

E136850

Flexible Sign Face Tensioning System and Sign Framesdesignated "Clip Tensioning System." 1. The suitability of the flexible sign face material and the clip tensioning system assembly when used on an outdoor sign to prevent the entrance of water, shall be determined in the end-use application. 2. The suitability of the mounting of this assembly to the end-use sign shall be determined. Considerations should be given to the reliable mounting of the assembly to the sign body. 3. This system together with the flexible face material shall comply with the external decorative face requirements of UL 48, particularly the clearances from heat generating components to decorative plastic panels. 4. The suitability of secureness of the clamp and flexible material shall be judged in the end-use application. 5. The insulation of the system and the sign shall conform with the instructions provided with this tensioning system. Flexible Sign Face Tensioning System and Sign Frames Model FH, for use as a frameless design, Models FC, 5365, for use with Frames Models RF, R3F, Model 24-63-390, for use with Frames Models 24-63-300, 24-63-305, 24-63-310, 24-63315, and Model 5360, for use with Frames Models 2090, 2142, 2094, 2105, 2104, 2085, 2065, 2112, 2092. 1. The following table details the acceptable clip/frame combinations: Clip FC, 5365 FH 24-63-390 5360 Frame (frameless design) RF, R3F 24-63-300, 24-63-305, 24-63-310, 24-63-315 2090, 2142, 2094, 2105, 2104, 2085, 2065, 2112, 2092

2. The suitability of these tensioning systems in combination with any R/C (UYMR2) Flexible Sign Face Material to prevent entrance of water in outdoor sign applications shall be determined in the end product. 3. This product has not be evaluated for use as an ultimate enclosure. 4. Tensioning clips shall be spaced in the end product as described in the Installation Instructions. 5. When employed in a sign with any frame dimension greater than 6 feet the sign shall be provided with a means to prevent billowing. 6. The mounted assembly of sign face material in these tensioning systems shall comply with the external decorative face requirements of UL 48 particularly clearance to lamps and lampholders. 7. These clips have been determined to be suitable with any R/C Flexible Sign Face Material al least 0.020" (0.51mm) thick. Suitability for use with a material of lesser thickness shall be determined in the end product.

SIGNSTRUT LTD

E125271

64 ACI CENTER 5900 CROMDALE DR DUBLIN OH 43017

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

Sign Face Tensioning Systems, designated "KLICK-RAIL". 1. Suitable for use in outdoor signs. 2. Not suitable for use as an electrical enclosure. Class 2 LED Illumination, RVI Series. 7. These products are only suitable for connection to a UL Listed or UL Recognized Class 2, DC power source. 8. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 9. Class 2 LED Illumination, RVI Series is rated 20 W per 2.7 m length with yellow LEDs and 21 W per 2.7 m length with Red LEDs. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 W per Class 2 circuit. 10. These products are suitable for use in dry, damp locations. When the Class 2 output is 12 V or under, these products are suitable for wet locations. 11. These products are not required to be enclosed or protected from weather.

SIKA CORPORATION 30800 STEPHENSON HWY MADISON HEIGHTS, MI 48071

E312031

Acrylic adhesives, Model Nos. SikaFast 3121, 3131S. 1. The adhesive system may be used for securement of any combination of surfaces listed in Table A. The end-product operating temperature is not to exceed the lowest temperature rating of the combination. 2. The adhesive system is suitable where exposed to high humidity and occasional exposure to water. The minimum temperature rating is -35°C (-31°F). 3. This adhesive system is suitable for application to smooth flat surfaces, except where another surface configuration is noted. 4. The materials have been evaluated for adhesive compatibility and stability only. No electrical or flammability tests have been performed. The engineer must consider the need to investigate the part for other than the properties investigated, in accordance with the applicable end-product standard and/or the requirements outlined in UL 746C, Standard for Material Used in Electrical Equipment Evaluations. 5. The suitability for the use when exposed to oil, chemicals, refrigerant, soap, x-rays, ultraviolet and the like has not been determined by this investigation, unless otherwise noted. 6. When considering the use of the adhesive system, One square inch of surface covered by adhesive can support in shear tension the weight specified in Table A. When determining the suitability of the adhesive system, the bond strength value should be based on the lowest average as-received bond strength value of the material combination. TABLE A Sikafast 3121 Substrate Combination Cold rolled steel to Cold rolled steel Galvanized steel to Galvanized steel Stainless steel to Stainless steel Aluminum to Aluminum Polycarbonate to Polycarbonate 3131S Substrate Combination Cold rolled steel to Cold rolled steel Galvanized steel to Galvanized steel Stainless steel to Stainless steel Aluminum to Aluminum Polycarbonate to Polycarbonate Max. Operating Temp. °C 90 75 90 130 65 As - Received Bond Strength (PSI) 386 420 333 401 248 E215393 Max. Operating Temp. °C 90 75 90 130 65 Lbs/in. 407 401 310 331 221

2

SLOANLED DIV OF SLOAN CO INC. 1833 PORTOLA ST. VENTURA CA 93003

LED Strips For Use on Class 2 Circuits, Cat. No. 701174, 701181 and 701195 with suffix -R, -Y, -A, -B, -W, or -G followed by -1" through -24". 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 volt AC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products may be cut into segments through a black mark provided on the printed wiring board. No other cut across the board is permitted. 4. Cat. No. 701174 is rated for 4.2 watts per foot, Cat. No. 701181 is rated for 9.2 watts per foot and Cat. No. 701195 is rated at 1.5 Watts per foot. The total number of feet of each type and inches for the inch unit are not to produce a total wattage of greater than 60 watts per Class 2 circuit.

65

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

5. These products are suitable for use in dry, damp and wet locations. 6. These products are not required to be enclosed or protected from weather. LED Lighting Units For Use on Class 2 Circuits, Cat. No. 701261, 701261-PW, 701340, 701340-PW with suffix ­R, -O, -Y, B, -G, -W, or ­A. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 V dc power source for Model 701340 and 7.5 V dc or 5 V dc power source for Model 701261. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. The total number of Model 701261 LED Lighting Units are not to exceed a total of 75 units per Class 2 circuit. The total number of Model 701340 LED Lighting Units are not to exceed a total of 40 units per Class 2 circuit. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather. LED Lighting Units For Use on Class 2 Circuits, Cat. No. "ChanneLED4" series for Use on Class 2 Circuits, Cat. Nos. 701269-RL-CC, 701269-YL-CC, 701269-RS-CC, 701269-YS-CC, 701269-B-CC, 701269-G-CC, 701269-W-PW, 701269-LW-CC, 701269-CM-XX-PW, 701269-RGB-PW & MiniWhite Series, Cat. No. 701269-WT-CC. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2 power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products are rated as follows: Cat Nos. 701269-RL-CC, 701269-YL-CC, 701269-RS-CC, and 701269-YS-CC are each rated 0.6 Watts per unit, Cat. No. 701269-B-CC, 701269-G-CC, and 701269-CM-XX are each rated 0.42 watts per unit, Cat. No. 701269-W-PW is rated 0.77 watts per unit, Cat. No. 701269-LW-CC is rated 4.2 Watts per unit, and Cat. No. 701269-RGB-PW is rated 1.32 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 4. All of these "ChanneLED4" units are suitable for use in dry, damp and wet locations, except Cat. No. 701269-W-PW is suitable for dry and damp locations only. Class 2 power supplies, "ThinLED", Model 701228 , with suffix -A, -B, -G, -R, -W or -Y; Cat. No. 701228-18, with suffix -A, -B, G, -R, -W or -Y. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, max. 12 V dc power source. . Only Models 701228-A, -R, or -Y are only suitable for connection to UL Listed or Recognized Class 2, max. 7.5 V dc. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. The total number of these products when interconnected is not to exceed a total of 14 feet or 14 "ThinLED" units per Class 2 circuit. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather. Class 2 power supply, Model LED Outline Lighting Systems "Border Light". 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 4. These products are provided with wire soldered on the printed wiring board for connection. 5. These products are suitable for use in dry, damp and wet locations. Class 2 LEDs, Modules designated, "LED STRIPE2 (Border Light)". 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15 Volt or less DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LEDs, "LED STRIPE2 (Border Light)", is rated max. 48 Watts per module. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. Class 2 power supply, Model 701285, 701349, 701351. 1. Power supply is intended to power LEDs in signs. 2. Power supply model is intended for permanent connection only. 3. These units are suitable for use in dry location without a need for an additional enclosure and in damp locations when installed inside a sign that complies with the Exclusion of Water Test in UL 48. 4. If the power supply output wiring is extended longer than the 5 foot leads provided, the spliced connections shall be made inside a Listed junction box suitable for the application included with proper grounding. Class 2 power supply, Model 701449, 701449-WP701450, 701450-WP, 701507, 701450, 701507-WP. 1. These power supplies have a single output that complies with Class 2 output requirements. 2. These products are suitable for use in dry damp and wet locations only. 3. The primary sides of these power supplies are suitable for connection with threaded type conduit only. The primary side of models 701449-WP (LP1060-08-GG-170), 701507-WP (LP1060-12-GG-170) and 701450-WP (LP1060-22-GG-170) are provided with 1/2 inch trade size knock out for connection to Listed Heyco Products Inc, Cat. No. HFC 1/2-S liquid tight flexible nonmetallic conduit connectors. 4. The maximum rated output power for Model 701450(LP1060-22-YZ-E) and 701450-WP (LP1060-22-GG-170)is 61 watts, for Model 701507 (LP1060-12-YZ-E) and 701507-WP (LP1060-12-GG-170) is 60 watts, and for Model 701449 (LP1060-08-YZ-E) and 701449-WP (LP1060-08-GG-170) is 40 watts. 5. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 6. Models 701449(LP1060-08-YZ-E), 701507 (LP1060-12-YZ-E) and 701450 (LP1060-22-YZ-E) - When not marked for indoor use only, the power supply primary bracket shall be provided with min. 3.5 threads and tapered for connection to liquid tight conduit fitting.

66

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

7. When not marked for indoor use only, all units shall be provided with liquid tight fittings on the primary and secondary circuits. Class 2 power supplies, Model 701507-MOD (AD060S110/220-SLN). 1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products with Class 2 outputs are suitable for use in dry, damp and wet locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. When used in wet locations, each unit shall be provided with Listed (QCRV) 1/2 inch, liquid tight conduit fittings on primary circuit. 5. When used in a cord connected product, the need for conducting a leakage current test shall be considered in the end product. 6. When not marked for "Dry and Damp Locations Only" the power supply primary bracket shall be provided with min. 3.5 threads and maximum 5 threads tapered for connection to liquid tight conduit fitting. If less than 3. 5 threads, the liquid tight shall be provided with watertight fitting Listed (QCRV) 1/2 inch, liquid tight conduit fittings. 7. The suitability of grounding connection shall be determined in the end-use product. LED Class 2 Lighting Assemblies Model Nos. "ChanneLED4", Cat. Nos. 701269-RL-CC, 701269-YL-CC, 701269-RS-CC, 701269-YS-CC, 701269-B-CC, 701269-G-CC, 701269-W-PW, 701269-WL-CC, 701269-CM-XX-PW, 701269-OS-CC, 701269OL-CC, 701269-XT-CC where X maybe W, R, B, O, Y, A or G; 701269-RGB-PW and "ChanneLED4 MiniWhite" Series, Cat. No. 701269-WT-CC, 701269-XL-MB, 701269-XS-MB, 701269-XT-MB and 701269-XT-CC where X maybe W, R, B, O, Y, G or A. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2 power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products are rated as follows: Cat Nos. 701269-RL-CC, 701269-YL-CC, 701269-RS-CC, 701269-OS-CC, 701269-OLCC and 701269-YS-CC are each rated 0.6 Watts per unit, Cat. No. 701269-B-CC, 701269-G-CC, and 701269-CM-XX are each rated 0.42 watts per unit, Cat. No. 701269-W-PW is rated 0.77 watts per unit, Cat. No. 701269-WL-CC and 701269-XLMB are rated 4.2 Watts per unit, Cat. No. 701269-RGB-PW is rated 1.32, and 701269-WT-CC is rated max. 2.4 Watts per unit, Cat. No 701269-XS-MB, 701269-XT-MB and 701269-XT-CC are rated 1.2 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply per Class 2 circuit. 4. All of these "CHanneLED4" units are suitable for use in dry, damp and wet locations, except Cat. No. 701269-W-PW is suitable for dry and damp locations only. Class 2 LED Module, Cat. No. ChanneLED4", 701269-XL2-MB Series where X may be replaced by W, B, G, R, Y, A or O. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits. 3. Class 2 LEDs designated "ChanneLED4", 701269-XL2-MB Series are each rated max. 7.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

SLOANLED DIV OF SLOAN CO INC. 1833 PORTOLA ST. VENTURA CA 93003

E245480

Class 2 power supply, Model 701680, 701681. 1. These power supplies have a single output that complies with Class 2 output requirements. 2. These products are suitable for use in dry damp and wet locations only. 3. The primary sides of these power supplies are suitable for connection with threaded type conduit only. 4. The maximum rated output power for Model LP1060-13-YZ-E, LP1060-17-YZ-E and LP1060-21-YZ-E is 61 watts, for Model LP1060-24-YZ-E is 60 watts. 5. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 6. When not marked for indoor use only the power supply primary bracket shall be provided with min. 3.5 threads and tapered for connection to liquid tight conduit fitting. 7. When not marked for indoor use only, all models shall have liquid tight fittings on both primary and secondary circuits.

SOUTHERN MFG CO 501 HERNDON AVE. ORLANDO, FL 32803

E251315

Class 2 LED Module, Cat. No. S401-156. 1. These modules have been evaluated for use on a UL Listed or Recognized Component Sign Accessory (UYMR2) Class 2 power source rated 24 V DC. 2. The suitability of supply sources other than Class 2 has not been evaluated and shall be determined in the end-product. Special consideration shall be given to the enclosure and spacing requirements in UL48. 3. These modules are suitable for use in dry, damp or wet locations. They are not required to be enclosed or protected from weather. 4. The total wattage drawn by all modules connected to a single Class 2 supply shall not exceed the rated capacity of that supply. 5. Up to four modules may be connected and powered in series, as long as they comply with condition #4.

67

6.

SIGN COMPONENTS MANUAL (SAM)

Mounting surface shall be able to withstand a temperature of 80°C.

April 21, 2008

SPARKLE SIGN CO. LTD. 7938 A WRIGHT RD. HOUSTON, TX 77041

E237563

Shell Lighted Channel Letter, Cat. Nos. Shell Lighted Channel Letter. 1. The channel letters may be used as an electrical enclosure when provided with sign face material in the end-use application that is suitable for electrical enclosure use. 2. The neon tube shall be spaced a minimum of ¼ in. from the inside walls of the plastic enclosure, and ¼ in. from the sign face. 3. Openings for drain holes, conduit, electrode receptacles and mounting shall be provided in accordance with the Standard. 4. The channel letters are suitable for use in dry, damp, and wet locations. 5. The channel letter panels shall be secured with R/C (UYMR2) Lord Cat. No. 7542D.

SPARTECH PLASTICS 2500 SPARTECH DR, CAPE GIRARDEAU MO

E202184

63701

Rigid sign enclosure systems for use in electric signs, designated: Sungard and Sungard Plus in clear and white colors only and, PC-2000 and PC-2000 Plus in clear color only. 1. Furnished in the form of sheets, with a minimum thickness of 0.10 in. (2.54 mm). 2. Suitable for use as an electrical enclosure, however, only the non-UV coated side may be exposed to live parts. 3. Sungard and Sungard Plus suitable for use in outdoor signs with the UV coated side on the exterior. 4. PC-2000 only suitable for indoor use. 5. The mounting system must secure the sign face to the enclosure in such a way that the edges of the sign face are not exposed to the interior of the sign. This may be accomplished with channels, flanges or other suitable mechanical means. 6. These materials have a use temperature of 80 °C. If a heat producing Component such as electrode, transformer or ballast is located within 1 inch of the material, a temperature test should be conducted in the end product. 7. All materials have been investigated for the securement of conduit, electrode housings or the like. 8. The following markings or equivalent shall be provided where readily visible during servicing. a. "Do not attempt to replace, repair or service a damaged sign face. For servicing of this sign, contact ________." (Blank to be replaced by Sign Company's name, City and State.) b. "Replace only with ______, Type ______." (Blanks to be replaced by Recognized Material Company's name and material Type or designation.) Marking - Company name and system designation is marked on protective film provided over surface of material such that a piece dimensioned 2 ft by 2 ft minimum will contain all required markings. System designation will be the same as material designation except may be followed by additional digits. A marking indicating the side which is UV coated will be provided in the same dimensions as given above.

SPECTRUM MFG INC UNIT 1 435 HORNER AVE TORONTO, ON M8W 4W3 CANADA

Sign Control System Model 6X4. 1. This device is intending to be installed in an advertisement display. 2. The securement of stepper motor shall be evaluated in the end product.

E308789

STARBRIGHT TECHNOLOGY L L C SUITE D 14726 GOLDENWEST ST WESTMINISTER, CA 92683

E249079

Class 2 LED kit, Model Models FLEXOR. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. Class 2 LED Illumination, Flexor is rated 60 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit. 4. Class 2 LED Illumination, Flexor is provided with a R/C wire soldered on the printed wiring board for connection in series. 5. These products are suitable for use in dry, damp and wet locations. 6. These products are not required to be enclosed or protected from weather.

STRONG HAND ENTERPRISE LTD 5TH FL, 30 SZE-CHUAN 2ST

E303214

68 SHI-TUN DISTRICT TAICHUNG, 407 TAIWAN

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

LED Module, Models RGBX., WP-X Series.FLEXOR. 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 5VDC or 12VDC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. These products are rated per the Table on Page 2. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit. 4. These products are suitable for use in dry, damp and wet locations without additional enclosures.

SUN LED SIGN SUPPLY INC. 2810 PECK RD. EL MONTE, CA 91733

E243914

Class 2 LEDst, Models SLS-1-X, SLS-2-X. 1. These products are only suitable for connection to the output of a UL Listed or R/C (UYMR2), Component ­ Sign Accessory Class 2 LED power supply or UL Listed or R/C Class 2 Power Supply rated 12 V DC. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. Class 2 LED Illumination is rated per following table. When units are connected to a Class 2 circuit, their number is to be limited to draw a total wattage of no greater than the secondary current rating of each Class 2 circuit. The following identifies the rating to be used in calculating the maximum number of units per circuit. Cat. No. SLS-1-X Load Max (mAmps) 30 Watts 0.36 0.36

SLS-2-X 30 4. These products are suitable for use in dry, damp and wet locations. 5. The weather enclosure does not require evaluation.

SUNLITE TECHNOLOGIES LTD. 6TH FL, UNIT C 66 TSUN YIP ST, HOWARD FACTORY BLDG KWUN TONG, KOWLOON HONG KONG

E196832

Neon Tube Support, Cat. Nos. TS921Y-X and TS922Y-X. 1. Adjustable tube support are to be solvent bonded with Trichloromethane, Bichloromethane, or Methylene Chloride at a maximum height of 31.75 mm (1.25 in.) from base to the bottom of cradle.

SUPERLITE TECHNOLOGY CO INC 1752 REDDING AVE ROSEMEAD, CA 91770

E248769

LED sign system, Models 3LED-100X-R, 3LED-100X-Y, 3LED-100X-G, 3LED-100X-B, 3LED-100X-W, Where R, Y, G, B and W stand for Red, Yellow, Green, Blue, and White Colors respectively. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 12 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply and 60 watts per Class 2 circuit. Cat. No. 3LED-100X-R and -Y draw 15 ma per unit and 3LED-100XG, -B and -W draw 20 ma each. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather. LED sign system, Models HLED-LMB-R, HLED-LMB-Y, HLED-LMA-G, HLED-LMA-B, HLED-LMA-WW, HLED-LMA-CW. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 15V AC or Less and 30 volt DC or Less power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from the weather in the end product.

SUPER VISION INTERNATIONAL INC 8210 PRESIDENTS DR

E220835

69 ORLANDO, FL 32809

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

LED sign system, Model Flex LEDs. 1. These LEDs must be connected to a UL Listed or UL Recognized Class 2, 12 Volt DC 5 A power source or (UYMR2) Advance Transformer Co., Model LED120A0012V50F. 2. These LEDs have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. No more than 40 feet or 40 LED boards that are provided in the LED Colors (Red, Clear Red, Amber, Yellow or Orange) are to be interconnected together on one single Class 2 circuit. 4. No more than 21 feet or 21 LED boards that are provided in the LED Colors (Blue, White, Green or Aqua Blue) are to be interconnected together on one single Class 2 circuit. 5. Suitable for use in dry, damp and wet locations. LED sign system, Model Flexmod. 1. These products are only suitable for connection to a UL Listed Class 2, 5 Volt DC, power supply or any UL Recognized Class 2, 5 Volt DC, power supply listed in the SAM, that complies with the stated conditions of acceptability. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. This Class 2 product, when connected to a Class 2 circuit, shall not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply.

T I R SYSTEMS LTD 7700 RIVERFRONT GATE BURNABY, BC V5J 5M4, CANADA

E246878

LED Lighting Kit, Cat. No. Class 2 LEDs Chain LightScript Series. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When these units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather.

TECH 22 1160 JOSHUA WAY VISTA, CA 92083

E192264

Controller/Dimmer for Neon Power Supplies, Model GEN-3, CNTM12-xxx, CNTM24-xxx 1. Must be inside an electrical enclosure in the end product. 2. The controller/dimmer is intended to be used with neon supplies and solid state relays that have an optically isolated control input rated 3 to 6 Volts, 2 to 10 mA. 3. The controller is rated for a 120 Volt input, 20 mA with an output of maximum 6 Volts, and 350 mA. 4. This controller is intended only for use in indoor and inside outdoor signs. Dimmer Load, Cat. No. "Active load". 1. Must be inside an electrical enclosure in the end product. 2. Dimmer load is for use with applicant's neon power supplies or controllers with 120 V dimmer control input. 3. Dimmer load for use in indoor signs or enclosed within outdoor signs. o 4. This dimmer load has been evaluated in a 40 C ambient only. 5. If a heat producing component such as electrode, transformer or ballast is located within 3 in. of the dimmer load, a temperature test should be conducted in the end product. Electronic Incandescent Lamp Controller, Cat. No. Chase 004 Electronic LED and Incandescent Lamp Controller, Cat. Nos. CNTS3D-xxx, CNTS3A-xxx, CNTS4D-xxx, CNTS4A-xxx, CNTS5D-xxx and CNTS5A-xxx 1. Must be inside an electrical enclosure in the end product. 2. Controller is only suitable for connection to a UL Listed or Recognized Class 2, 12 to 24 V dc or ac (50/60 Hz) power source. 3. This controller is intended only for use in indoor and inside outdoor signs. 4. Shall not be located within 3 in. of heat producing components such as electrodes, transformers or ballasts. LED Modules, Model designation LED strips XXX YYY, where XXX and YYY may be replaced with any alpha numeric character from 000 to 999 or from AAA to ZZZ or combination of letter and numbers; T-lights XX YYY, model designation where XX and YYY may be replaced with any alpha numeric character from 00 to 99 or from AA to ZZ or combination of letter and numbers; Spotlight XXX where XXX may be replaced with any alpha numeric character from 000 to 999 or from AAA to ZZZ or combination of letter and numbers; LED assembly XXXXXX, where XXXXXX may be replaced with any alpha numeric character from 000 to 999 or from AAA to ZZZ or combination of letter and numbers. All models may or may not be followed with suffix KK, where KK may be replaced with any alpha numeric character from 00 to 99 or from AA to ZZ or combination of letter and numbers. 1. These products are only suitable for connection to a Class 2 power source, rated 24 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 15 V. 3. These Class 2 LED modules are each rated max. 60 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 24 Vdc or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

70

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

E315540 TECHNI-LITE SYSTEMS INC PO BOX 445 910 HIGH ST PETERBOROUGH, ON K9J 6Z3 CANADA Fluorescent Grids Models LG17MF, LG25MF, LG32MF, LG17BX, LG25BX, LG32BX. 1. Sign Components LG17MF, LG25MF, and LG32MF being power supply cord connected are suitable for use only in indoor portable power supply cord connected signs. 2. Sign Components LG17BX, LG25BX and LG32BX are suitable for use in a damp location within a sign where protected from the weather. 3. The Electrical rating shall be as per table below. MODEL RATING 120 V - 50/60 Hz 240 V - 50/60 Hz LG17MF, LG17BX 0.50 A 0.22 A LG25MF, LG25BX 0.74 A 0.32 A LG32MF, LG32BX 0.95 A 0.40 A 4. The maximum number of grids that can be inter-connected shall not exceed maximum number of units as noted below. Model Number Maximum Number of Units LG17MF, LG17BX 12 LG25MF, LG25BX 8 LG32MF, LG32BX 6 5. Suitability of the branch supply connecting means and interconnecting means for models with suffix MF shall be evaluated in the end use application.

TECNOLUX INC 103 14TH ST BROOKLYN, NY 11215

E248791

High Voltage Electrodes/GTO Splice End Cap, Model xxSC1y, xxSC1yDB, where xx is 10, 12, 15 or 18 and y is B or W, For Dry or Damp Locations Only. 1. Model Nos. xxSC1yDB and xxSC1y are suitable for use in USL Listed Signs when marked for Dry or Damp Locations Only. Model Nos. xxSC1yDB are suitable for use in CNL Listed Signs when marked for Dry Locations Only. 2. They have been evaluated with GTO cable with integral sleeving, cat. no. GTO15 (14 through 18 AWG) manufactured by Silitherm S.R.L. only. Use with any other GTO type or manufacture will need to be evaluated in the end product. 3. Models 18SC1xDB and 18SC1x are additionally rated for 100mA.

TELEDYNE LIGHTING & DISPLAY PRODUCTS 12964 PANAMA ST LOS ANGELES, CA 90066

E215992

LED Lighting Kit, Cat. No. 01001215, 01001218, 01001225, 01001245, 01001248, 01001250, 01001255, 2PL01001215, 2PL01001220, 2PL01001225, 2PL01001245, 2PL01001250, 2PL01001255,followed by ­2 through -6, followed by a suffix W, B, G, A, or R. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24-27 volt DC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products are provided with a break point in the printed wiring board between each LED and interconnecting leads to increase the distance between LEDs. No other cut across the board is permitted. 4. These products are suitable for use in dry, damp and wet locations. 5. These products are not required to be enclosed or protected from weather. LED Power Supply with Class 2 output, Models 01001270-1 01001270-2, 01001290-1, 01001290-2. 1. These power supply is provided with an enclosure that complies with the enclosure requirements in UL 48. 2. These power supply is suitable for use in dry and damp locations. This power supply is suitable for use in wet location when installed in an enclosure protected from precipitation. 3. The output of the power supply is rated 24 V DC and 4 amps for Model 01001270-1 and 27 VDC, 3.55 amps, 96 W for Model 01001270-2. All components connected to this power supply shall be located in a dry or damp location because the output exceeds 15 V. LED Lighting Kit, Cat. No. Cat. Nos. SK1005 and SK1006,, "Green Photon Engine", "Red Photon Engine" and "Red-GreenBlue (RGB) Photon Engine" LEDs. 1. These products are only suitable for connection to a maximum Class 2 power source, rated 30 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies rated greater than 30 V DC. 3. Class 2 LEDs, SK1005 and SK100 are each rated max. 48 Watts per unit. Class 2 LED Units - "Green Photon Engine" is rated max. 18 Watts per unit. "Red Photon Engine" is rated max. 22.5 Watts per unit and "Red-Green-Blue (RGB) Photon Engine" is rated max. 12 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply. 5. These products are not required to be enclosed or protected from the weather.

THE BRIGHT GROUP PTY LTD 106 DERBY ST

E245307

71

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

SILVERWATER SYDNEY NSW 2128, AUSTRALIA

Cold cathode fluorescent light assemblies Series TBG-UNITOP-XX-YYY-Z, where XX may be any alphanumeric character combination from 00 to 99, AA to ZZ, or any combination of letters and numbers; YYY may be any alphanumeric character combination from 000 to 999, AAA to ZZZ, or any combination of letters and numbers; and Z may be 12 or 24 1. These components are to be installed in accordance with the manufacturer's instructions in the end product. 2. These products are only suitable for connection to a Class 2 power source, rated 24 Volt or less. 3. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits rated greater than 24 V. 4. These devices are rated as specified below. Catalog Number Type Load Max. Rated Input V A TBG-UNITOP-XX-YYY24 1 Cold Cathode Z Fluorescent and LED 5. No tests have been conducted on these components and as such, end product testing should be considered. 6. Suitability of the input leads (AWG, temperature rating, etc...) and the supply connector shall be considered in the end product.

TRANSCO INC PO BOX 4064 WEST COLUMBIA SC

E150099

29171

Switch boot, Model 1100 may be followed by NSZ.. Optionally, Molded Silicone Rubber Boot/Nut assembly may be provided with a WOYR2 switch by Transco, Model 1000. 1. This device is intended to be used in outdoor electric sign applications where the boot/switch toggle are protected from inadvertent abuses. The suitability of protective barrier shall be determined in the end-use application. 2. Consideration shall be given to conducting a Water Exclusion Test as a regular part of each inspection. The suitability of a Listed toggle switch for use with this boot shall consider the following: (A) The toggle (switch actuator) shall be metal, and (B) The toggle (switch actuator) shall be rounded to prevent abrasion and cutting of the boot. (C) The assembly shall be mounted on the bottom or side surface of a sign body only. 3. Unless the switch body is completely enclosed in a Listed weatherproof enclosure, drain openings in the bottom of the switch enclosure are to be provided in accordance with UL 48. 4. The Molded Silicone Rubber Boot/Nut assembly may be optionally provided with a WOYR2 switch by Transco, Model 1000 rated 20 A, 120-277 Vac; 7.5 A, 125VL; 3HP, 120/240 Vac. Sign Face Tensioning System, Part Nos. Trans-clip SB and Trans-clip SC. 1. The suitability of these tensioning systems in combination with any Recognized flexible sign face material (UYMR2) and UL 48 to prevent entrance of water in outdoor sign applications, shall be determined. 2. The mounted assembly of sign face material in these tensioning systems shall comply with the external decorative face requirements of UL 48 particularly clearance to lamps and lampholders. 3. These tensioning systems in conjunction with the Recognized flexible face material have not been investigated for use as an electrical enclosure. 4. The suitability of the "fit" of the face material and the secureness of the clamping system on the sign, shall be judged in the end application. 5. When these systems secure flexible faces on signs with any dimension (length or width) greater than 6 ft, suitable braces should be employed to prevent the material from billowing and creating short spacings to heat sources. 6. The tension clips shall be mounted not more than 12 in. apart on center. Neon Supply System, Part Nos. EWS and EIK Series. May be followed by "-W" to indicate wet location. 1. All transformers are pre-mounted and spaced to maintain minimum 1-1/2 inches between any high voltage terminals and grounded dead metal. 2. If provided with "-W" designation the Neon Supply System has been provided with a Transformer Mounted 1/2 in. off bottom of enclosure and the enclosure has been provided with two 3/8 in. drain openings. 3. For EIK Series, the models are provided with Listed Integrally Sleeved GTO Cable and Listed Polymeric Splice Enclosures (Boots) that have previously been investigated to the requirements of UL's UYTA Classification Program. 4. Mounting of the WOYR2, Model 1000 Toggle Switch and UYMR2, Model 1100, 1100NSZ or 1100CCJ Toggle Switch Boot Cover shall be evaluated in the End-Product Assembly per the requirements found in the Sign Components Manual. 5. For EIK Series, one end of the integrally sleeved GTO Cable may be provided with a Listed (ZMVV) uninsulated ring terminal that is suitable for the application and has been secured per the manufacturer's specifications. Electrode Receptacle Insulators, Model Nos. 1030-8, 1030-10, 1030-12. 1. This product is an insulator and has not been evaluated as an enclosure. 2. Limited to use inside dry, damp and wet location signs and outline lighting where not subject to precipitation. 3. Rated for a maximum 15kV, 7.5 kV to ground.

72

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

TRANSFOTEC INTERNATIONAL LTD 400 RUE DU PARC ST EUSTACHE, QC J7R 0A1 CANADA

E301099

LED power supply with Class 2 outputs, Cat. Nos. LMPS-350, LMPS-750. for use with LED Current Module, Type LCM "+". 1. These power supplies has a single output. The output has been evaluated and found to comply with Class 2 output requirements. 2. These power supplies are provided with an enclosure that is suitable for installation in a damp or dry location. 3. LED Current Modules "LCM-xx-x-xx-x" must be used with these Listed Class 2 Power Supplies, Models LMPS-350 or LMPS750. These power supplies are potted. 4. The power supply Model LMPS-350 is capable of providing power for a minimum of 35 W. The minimum load corresponding to a one(1) LCM mini equibrite red is 188 mA. This leads to 35 W divided by 188mA equals 186 LCM modules for the red color equibrite on one (1) LMPS-350. The same calculation for the highest brightness LCM long Megabrite white (rated 1.56W) the maximum gives 22 LCM modules (35W divided by 1.56W). The loading capability could be any mix of different model for a maximum of 35W. 5. The power supply Model LMPS-750 is capable of providing power for a minimum of 75W. The minimum load corresponding to a one (1) LCM mini equibrite red is 188 mA. This leads to 75 W divided by 188mA equals 398 LCM modules for the red color equibrite on one (1) LMPS-750. The same calculation for the highest brightness LCM long Megabrite white (rated 1.56W) the maximum gives 22 LCM modules (35W divided by 1.56W). The loading capability could be any mix of different model for a maximum of 75W. 6. Each power supply shall be installed in accordance with the installation instructions. 8. Spacing between adjacent power supplies is 1 in. end to end and 4 in. any other direction or may be used in maximum ambient temperature of 50(C.

TRIDONICATCO GMBH & CO KG FAERBER GASSE 15 6850 DORNBIRN, AUSTRIA

E313318

Class 2 LED Module, Cat. Nos. PXXX YYY Series, where XXX can be 503, 510, 511, 515, 516 and YYY can be any alphanumeric character combination from 000 to 999 incl., AAA to ZZZ incl. or any combination of letters and numbers. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 12 V. 3. Class 2 LED modules, Cat. No. Cat. No. PXXX YYY series are each rated max. 18 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

TRI-GLOBAL L L C 2111 UTOPIA AVE NASHVILLE, TN 37211

E258921

Electrode Receptacle Insulator "Igloo", Cat. Nos. RCAP. 1. This product in not an enclosure, and suitability of the ultimate enclosure shall be determined during the end product investigation. 2. Limited to use in dry and damp locations only. 3. Rated for a maximum 15kV, 7.5kV to ground. 4. This product has been determined to be suitable for use with a #8 screw; suitability of use with any other screw size shall be determined in the end product. 5. Accessibility to live parts shall be evaluated in the end product investigation. Switch Boot, Cat. Nos. 1201. 1. This switch boot was evaluated for use on a toggle switch with 19mm long actuator mounted on a 12mm tall threaded `stem, with a 12 x 1.0mm thread. Suitability of any other switch size shall be determined in the end product. 2. The suitability of the switch ratings shall be determined in the end product. 3. This device is suitable for use in outdoor electric sign applications and needs to be evaluated for water exclusion in the end product. 4 The toggle switch for use with this switch enclosure shall comply with the following: a. The toggle (switch actuator) shall be rounded to prevent abrasion and cutting of the switch enclosure. b. The assembly shall be mounted on the top or side surface of a sign body only. c. Unless the switch body is completely enclosed in a weatherproof enclosure, drain openings shall be provided in the bottom of the enclosure in which the switch is installed. d. The toggle (switch actuator) shall be metal. 5. The switch boot shall be installed using 6 in lbs of torque.

73 TRI-MAG Inc. 1601 N CLANCY ST VISALIA, CA 93291

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

E309796

LED Power Supply with Class 2 output, Models TMG-Z016-W, TMG-Z336. 1. These power supplies have a maximum of two Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These power supplies have not been provided with a suitable enclosure. In the end product these units shall be enclosed. 3. When used in a cord-connected products, the need for conducting a leakage current test shall be considered in the end product. 4. The product was tested for use at the maximum ambient temperature (Tma) of 65°C permitted by the manufacturer's specification. This product will need to be temperature tested in the end product and the results cannot exceed 65°C. 5. This product is intended for use in changing message signs. 6. These products with Class 2 outputs are suitable for use in dry and damp location. 7. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure.

TRIAD MAGNETICS 22520-B TEMESCAL CANYON RD CORONA, CA 92883

E305150

LED sign system, Models TLD1020-10-Cnnnn, TLD1020-12-Cnnnn, TLD1020-13-Cnnnn, TLD1020-15-Cnnnn, TLD1020-17Cnnnn, TLD1020-18-Cnnnn, TLD1020-22-Cnnnn, TLD1020-24-Cnnnn, TLD1020-36-Cnnnn, TLD1040-09-Cnnnn, TLD1040-10Cnnnn, TLD1040-12-Cnnnn, TLD1040-13-Cnnnn, TLD1040-15-Cnnnn, TLD1040-18-Cnnnn, TLD1040-22-Cnnnn, TLD1040-24Cnnnn, TLD1040-36-Cnnnn. Where the optional suffix "Cnnnn" may be any alphanumeric character. 1. The product shall be installed in compliance with the mounting, spacing, casualty, and segregation requirements of the ultimate application. 2. These units are provided with a Class 105(A) insulation system. 3. The suitability of the input and output connections shall be determined in each end use application. 4. These power units are intended for dry or damp location use only. 5. Strain Relief and Impact Tests have not been investigated. 6.The polymeric enclosure of each unit has not been evaluated as ultimate enclosure. The flame class of polymeric enclosure of each unit is V-2, and the necessity of additional fire barriers shall be determined in end product.

UJC ELECTRONICS 5110 PARK AVE DES MOINES, IA 50321

E239468

LED Board, Cat. Nos. LSM-X where X may be A-Z. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2 power source, rated 12 V dc. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products have not been evaluated to be suitable as an enclosure. 4. These products are suitable for use in damp, dry or wet locations.

ULTRAFLEX SYSTEMS CO 1578 SUSSEX TURNPIKE BLDG. #4 RANDOLPH, NJ 07869

E140576

Flexible sign face material, designated "Ultralon IV" or "ULTRALON V". 1. Suitable for outdoor use. 2. Not suitable for use as an electrical enclosure. 3. Base color white. 4. Minimum thickness 0.015 in. (0.38 mm), minimum thickness 0.021 in. (0.53 mm) when secured with Recognized Component ABC Sign Products tensioning systems. 5. Any dimension greater than 6 feet needs braces to prevent billowing. 6. Suitable for use with all Recognized Component Securement and Tensioning systems. 7. Securement and tensioning systems shall reliably secure the face to the sign and pull the face taut in all directions.

UNIVERSAL LIGHTING TECHNOLOGIES 1430 WALL TRIANA HWY MADISON, AL 35756

E315636

LED Class 2 Modules, Cat. Nos. LEDP503X-YY(@), LEDP510X-YY(@), LEDP511X-YY(@), LEDP515X-YY(@), LEDP516XYY(@) where (@) X can be R, A, G, B, O, NW, DL or YW, YY can be 8V or 12V. 1. These products are only suitable for connection to a Class 2 power source, rated 12 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limits and which is rated greater than 12 V. 3. Class 2 LED modules when units are connected to a Class 2 circuit, are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

74 US LED SUITE 200 1800 BERING Houston, Texas 77057

SIGN COMPONENTS MANUAL (SAM)

E226833

April 21, 2008

LED Class 2 Modlight Controller, Model MLPS-350-48-12. 1. These products need to be protected from precipitation by being housed where protected from rain, snow, and water spray. 2. These products are intended to be supplied only by a UL Listed power source or a UL Recognized Component power source with a Class 2 output. 3. The output of this product complies with Class 2 requirements. Class 2 LED Module, Model MY-12-K-XX "MegaX" Series, where Y may be replaced by any number from 0 to 99 incl., K may be replaced by W, R, B, Y, G or RO and XX is optional, where it may be replaced by any alphanumeric characters (0 to 9 incl. or A to Z incl. or combinations).Mega, Accent or Pinnacle Series, Model Q ABC-XX-YY-ZZZZ Series, where Q may be P, M, C or blank; AB, XX and YY may be replaced by any alphanumeric characters (00 to 99 incl. or AA to ZZ incl. or combinations), and ZZZZ may be any alphanumeric characters (0000 to 9999 incl. or AAAA to ZZZZ incl. or combinations). 1. These products are only suitable for connection to a Class 2 power source, rated max 24 Volt DC or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit. 3. These Class 2 LED Modules are each rated max. 7.5 Watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 12 Volt DC or less. When rated 24 VDC, these products are suitable for dry and damp locations only. 5. These products are not required to be enclosed or protected from the weather in the end product. LED Accent Module, Model AC-X-Y-Z-T where X is the length of the module, Y identifies the operating voltage, Z identifies the color, and T identifies a standard. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2, 24 or 36 VDC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products are not provided with break points in the printed wiring board. No cuts across the board is permitted. 4. The AC-X-24-Z products are suitable for dry, damp and wet locations. 4. The AC-X-36-Z products are suitable for dry and damp locations and need to be protected from precipitation in wet locations by being housed where protected from rain, snow, and water spray. Class 2 LED Module, "Pinnacle Series", Model abc-X-Y-Z or RLS-X-Y-Z, where X can be any number from 0 to 9, Y can be any number from 00 to 99, Z can be any alphanumeric character. 1. These products are only suitable for connection to a UL Listed or Recognized Class max. 24 VDC power source. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. These products are not provided with break points in the printed wiring board. No cuts across the board are permitted. 4. These products are suitable for use in dry, damp, and wet locations. 5. These products are not required to be enclosed or protected from weather.

VERSEIDAG-INDUTEX GMBH INDUSTRISTRASSE 56 POSTFACH 2906 04150 KREFELD, GERMANY

E219382

Flexible sign face material, designated "Seemee IV". 1. Suitable for outdoor use. 2. Not suitable for use as an electrical enclosure. 3. Base color white. 4. Minimum thickness 0.015 in. (0.38 mm), minimum thickness 0.021 in. (0.53 mm) when secured with Recognized Component ABC Sign Products tensioning systems. 5. Any dimension greater than 6 feet needs braces to prevent billowing. 6. Suitable for use with all Recognized Component Securement and Tensioning systems. 7. Securement and tensioning systems shall reliably secure the face to the sign and pull the face taut in all directions.

VIRGINIA OPTOELECTRONICS INC 1405 ASHFORD CR BLACKSBURG, VA 24060

E 301137

Class 2 LEDs, Model ZLS-PCB-X Series, ZLS-PCBC-X Series and PL1-PMBC-X Series; where X can be any letter: R, Y, B, G or W; ZLS-PMBC-T Series; where T may be C or RGB. 1. These products are only suitable for connection to a Class 2 power source, rated 15 Volt or less. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited circuit and which is rated greater than 15 V. 3. Class 2 LEDs Cat. ZLS-PCB-X Series, ZLS-PCBC-X Series, PL1-PMBC-X Series and ZLS-PMBC-T Series are each rated max. 3 watts per unit. When units are connected to a Class 2 circuit, they are not to draw a total wattage of greater than the secondary or output rating of the Class 2 supply. 4. These products are suitable for use in dry, damp and wet locations with supply sources rated at 15 V or less. 5. These products are not required to be enclosed or protected from the weather in the end product.

75

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

VOLTARC TECHNOLOGIES INC. 400 CAPTAIN NEVILLE DR WATERBURY CT 06705

E31375

High voltage electrode/GTO splice insulators, "Kulka Kups" Cat. Nos. 12256, 12257, 12258, 12259, 12260, 12261, and, "Kulka Kaps" Cat. Nos. 12262, 12263, 12264, 12265, 12266, 12267. 1. These boots shall be pushed on to the electrodes until they are fully seated. 2. These boots are suitable for use with maximum 15000 Vac, 7500 V to ground. 3. These boots comply with the electrical enclosure requirements in UL 48. Therefore, they need no other enclosure on indoor signs and only a sign body to prevent exposure to the sun and rain in outdoor signs. 4. GTO cable within the "Kulka Kups" Series boots shall be rated min. 105 °C.

VOSSLOH-SCHWABE GMBH WASENSTRASSE 25

E231698

73660 URBACH GERMANY Class 2 power unit, LED array drivers Model EDXe130/12.006 1. This component has been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310, Fourth Edition, which would cover the component itself if submitted for Listing. 2. The equipment was submitted and tested for a maximum manufacturer's recommended ambient (Tmra) of 60°C. 3. Leakage current measurements shall be performed when more than four LED drivers are used in the equipment or when the LED driver is used in combination with other equipment in the end-use product. 4. The drivers are intended for installation inside an electrical enclosure. 5. The ground connection is not suitable as the equipment ground for a sign. Separate provision for sign grounding must be provided. 6. The drivers are suitable for outdoor dry or damp locations.

VYNEX SIGN SYSTEMS LTD 8175 WINSTON CHURCHILL BLVD NORVAL ON CANADA L0P 1K0

E173052

Flexible sign face material, designated "Marquee", "Premier", "Premier 2000", and "Reflections" all w/ suffix numbers. 1. Suitable for outdoor use. 2. These products are not to be used as electrical enclosures. 3. These products are acceptable for use with all Recognized Component Sign Securement and Tensioning. Marking - Company name or trademark Vyna-brite and model designation.

WALT DISNEY IMAGINEERING 1401 FLOWER ST. GLENDALE, CA 91221

E235817

Incandescent Outline Lighting, Cat. Nos. LTNG-XXXXXX where X denotes a number between 0 and 9. 1. The rim lighting units are acceptable use in dry, damp and wet locations. 2. The Rim Lighting System is not to exceed a string of sixty-six lights. 3. Make sure that each connector is inserted fully into the lampholder base. 4. Each lampholder is to be secured by screws through the holes provided on lampholder base. 5. This rim lighting system is only acceptable for use with maximum 6 Watt, Type 6S6/BB with brass base light bulbs. 6. When installed in a wet location, each light bulb is to be fitted with a thermoplastic lamp gasket part no. SK124 over the base of the glass envelope.

WALTON SIGNAGE CORP 3419 E COMMERCE SAN ANTONIO, TX 78220

E304298

Class 2 LED Modules, Models WT-2B, WT-2W, WT-2G, WT-3A, WT-3R. 1. These products are only suitable for connection to a UL Listed or R/C (UYMR2), Component - Sign Accessory Class 2 LED power supply. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 requirements. 3. These products are suitable for use in dry and damp locations. 4. The weather enclosure does not require evaluation. 5. These products have been evaluated for use in illuminating channel letters.

WESTRIM PRODUCTS 2268 FAIRVIEW BLVD PO BOX 300 FAIRVIEW TN 37062

E209062

Special use switch with boot for outdoor sign, Model 38057. 1. This device is intended for use in outdoor applications where the boot is protected from inadvertent abuse. 2. The special use switch mounting hole and mounting surface shall be free from burrs and have a close tolerance to the diameter of the switch mounting collar. 3. The special use switch shall be locked in place by a lockwasher or other means to prevent rotation. 4. The special use switch shall be provided with a means of indicating the on and off positions in accordance with UL 48. 5. The special use switch is to be used within its electrical rating in accordance with UL 48.

76

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

6. The Water Exclusion Test shall be conducted as a regular part of each inspection.

YANGZHOU YONGXIANG COMMERCE CO LTD ROOM 403, QIONGHUA BLDG 3 PIFANG ST YANGZHOU, JIANGSU 225002 CHINA

E310707

LED Power Supply with Class 2 Outputs, Model YXSW60-1205. 1. These power supplies have a maximum of one Class 2 output. The output of these power supplies has been evaluated to Class 2 output requirements for dc circuits. 2. These products are suitable for use in dry and damp locations. 3. In the end product, power supply spacing to other heat producing components shall be minimum 4 inches spacing to sidewalls, and minimum 2 inches spacing to top of enclosure. 4. The suitability of grounding connection shall be determined in the end-use product.

YOUNG ELECTRIC SIGN CO 5119 S CAMERON ST LAS VEGAS NV 89118

E138960

Sign flasher, Cat. No. YM-X where X is any number 1 to 6 incl. 1. The component shall be installed in compliance with the enclosure, mounting, creepage, clearance, casualty markings, and segregation requirements of the end-use application. 2. The terminal block and input/output connectors telephone jacks are not acceptable for field connections and are only intended for connection to mating connectors of internal wiring inside the end-use product. The acceptability of these and mating connectors relative to secureness, insulating materials, and temperature shall be considered in the end-use product. 3. A temperature test shall be conducted in the end-use product. The acceptability of the temperature reading or the following components shall be evaluated: Internal Wiring; PWB; Terminal Block, Max. 105°C; Transformer, Max. 90°C; Triac, Max. 100°C. Decoder driver, Model YDD-128. 1. The need for an overall enclosure shall be determined in the end-use application. 2. The suitability of the mounting means shall be determined in the end-use application. 3. The need for a Temperature Test shall be determined in the end-use application. The connectors are not acceptable for field connections and are only intended for factory installation to mating connectors of the end-use product. Sign Flasher, Lvflasher Model YMCROFLSH. 1. These products are suitable for use only when all live parts made inaccessible to contact by users during user maintenance while energized. 2. These products are suitable for use in dry and damp locations only. In damp locations, the unit must either be located at least ½ inches from bottom of enclosure and the bottom of the enclosure provided with drain holes or the unit installed within an enclosure that is gasketed to prevent the entrance of water into the compartment. 3. Power supply spacing to side wall and top of enclosure shall be minimum 2 inches. 4. Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 5. This component is to be installed and wired in the at end product manufacturer's location. LED Sign Unit, "Hockey Puck" Models YMRLED, YMR12LED, and YMR30LED. 1. These products are suitable for use in dry and damp locations only. In damp locations, the unit must either be located at least 1/2 inches from bottom of enclosure and the bottom of the enclosure provided with drain holes or the unit installed within an enclosure that is gasketed to prevent the entrance of water into the compartment. 2. In the end product the power supply spacing to sidewalls and top of enclosure shall be minimum 2 inches. 3. In the end product Power supply spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 4. This component is to be installed and wired in the at end product manufacturer's location. Class 2 LED Light Strings, Cat. No. FL Series. 1. These products are only suitable for connection to a UL Listed or Recognized Class 2 supply. If intended for Wet Locations, the power supply or transformer shall have an output of 12 volts. 2. These products have not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. 3. When connected to a Class 2 circuit, the lighting string shall be sized appropriately so as to not exceed the output current and power rating of the Class 2 supply. 4. The light strings, when connected to a Class 2, 12 Volt output supply, are suitable for installation in wet, damp and dry locations. The light strings, when connected to Class 2, 24 Volt output supply, are suitable for installation in damp and dry locations only. Sign Flasher, Model P. N.YFLASHAC. 1. This flasher is suitable for use when installed in a metal enclosure that is at least 12 by 12 by 3 inches having two 4 square inch openings on the side with a minimum 55 cfm fan mounted on the bottom. 2. Where more than one flasher is installed within an enclosure, each unit shall be located so that no part of each flasher is within 4 inches of each other. The enclosure shall be sized to provided at least 2 inches to sidewall and top and at least one or more fans provided that produces a cfm of a least 25 cfm per flasher. 3. No other components such as neon transformers or fluorescent ballasts shall be located within the enclosure with this flasher. 4. This component is suitable for use in dry and damp locations. In damp locations, the unit must either be located at least 1/2 inches from bottom of enclosure and the bottom of the enclosure provided with drain holes or the unit installed within an enclosure that is gasketed to prevent the entrance of water into the compartment. 5. This flasher is suitable for use on a 120 V, 60 Hz service and is rated for 0.25 amp input. It is capable of switching up to six 20 amp branch circuits each having maximum 16 amp load.

77

6.

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

This component is to be installed and wired in the at end product manufacturer's location as the connectors are not suitable for field installation. Changing Message Sign Transformer Assembly, Models YACDC1.5, YACDC3.3, YACDC750 may or may not be followed by X10 and LED Module "Sign Face" (LED Message Center), Model LEDMC. 1. Wiring and means of connection between modules shall be investigated in the end product requirements. 2. For models YACDC1.5, YACDC3.3 and YACDC750No no tests have been conducted on this component so consideration should be given to conduct input test, the normal temperature, dielectric voltage withstand components abnormal and rain tests in the end product changing message sign. 3. These components are not provided with suitable enclosure or sign body. The need for a electrical enclosure should be considered in the end product. 4. Transformer spacing to other heat producing components shall be minimum 4 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 2 inches. 5. Transformer spacing to other heat producing components shall be minimum 2 inches when minimum spacing to sidewalls and top of enclosure is kept at minimum 6 inches. Cold Cathode Self Ballast Lamp, Models "Cold Cathode Self Ballast Lamp" unit. 1. These components should be installed in accordance with the manufacturer's instructions. 2. These units are not intended for use with emergency exit fixtures or emergency exit lights.

SIGN COMPONENTS CLASSIFIED FOR USE WITH SPECIFIED EQUIPMENT (UYTA)

This category covers specific components that are Classified for use with components manufactured by others, such as: Listed GTO cable surface marked "Integral Sleeve" that is also Classified for use with specific Listed or Recognized Component neon electrode boots; and Listed or Recognized Component neon electrode boots that are also Classified for use with specific Listed GTO cable surface marked "Integral Sleeve." The combination of the integral sleeve and the specified neon electrode boots identified under this Classification has been evaluated and found to comply with the enclosure requirements for: a) the splice between neon tubing electrode leads and GTO cable, and b) the GTO cable leading to the splice. These products are provided with installation instructions that define the scope of the system and method of installation.

ELECTROBITS INTERNATIONAL SUITE 100 286 ST-PAUL W MONTREAL, QC H2Y 2A4 CANADA

E318961

Polymeric Neon Electrode Enclosures, Series Short Sleeve SS10mm30mA, SS12mm60mA, SS13mm60mA or SS15mm60mA; Series End Cap EC10mm30mA, EC12mm60mA, EC13mm60m or EC15mm60mA in combination with GTO Cable Sleeving Adaptor GTOCA260 for use with Electrobits, GTO-10, Paige Electrical GTO-15, Westrim Hi-Flex GTO-15, Neon Power Pro Neon Sign Cable, Transco GTO-15, ISS GTO TECH-2 GTO-15, or Silitherm GTO-15, GTO Cable with Integral Sleeve in dry and damp locations.

PAIGE ELECTRIC CO L P. 1160 SPRINGFIELD RD PO BOX 368 UNION, NJ 07083

E242084

GTO cable with integral sleeve, Cat. No. GTO-5, GTO-10, GTO-15, for use with neon electrode boots; Cat. No.EC5 and SS5 manufactured by Electrobits International.

RELIGHT AMERICA INC. 4510 W HARRY ST WICHITA, KS 67209

E307621

Neon Sign Cables Types NGL, NGL/NGL, NSC, NSC/NSC, NSC/NGL for use with Cat. No. EC5, SS5, SSW5 neon electrode boot manufactured by Electrobits for use in dry or damp locations.

TECNOLUX INC. 103 14TH ST BROOKLYN, NY 11215

E252991

GTO cable with integral sleeve , Cat. No. Cat. No. GTO-10 (18 AWG) for use with neon electrode boots; Part Nos. SS0, EC0, SS3, EC3, SS5 and EC5 manufactured by Electrobits International. Cat. No. GTO-15 (18 AWG) for use with neon electrode boots; Part Nos. SS0, EC0, SS3, EC3, SS5 and EC5 manufactured by Electrobits International. Cat. No. GTO-15 (14 AWG) for use with neon electrode boots; Part Nos. SSW3, ECW3, SSW5, ECW5, SSW6 and ECW6 manufactured by Electrobits International. Cat. No. GTO-15 (14 AWG) for use with neon electrode boots; Part Nos. SW3, EW3, SW5 and EW5 manufactured by Westrim Products.

78

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

Cat. No. GTO-15 (14-18 AWG) with Integral Sleeving manufactured by Silitherm S.R.L Classified for use with neon electrode enclosures Part Nos. xxSC1y and xxSC1yDB, where xx is 10, 12, 15, or 18 and y is B or W, manufactured by Tecnolux Inc. Suitable for dry and damp locations. Cat. No. GTO-15 (14 -18AWG) with Integral Sleeving manufactured by Silitherm S.R.L Classified for use with neon electrode enclosures Part Nos. xxSC1y and xxSC1yDB, where xx is 10, 12, 15, or 18 and y is B or W, manufactured by Tecnolux Inc. Suitable for dry and damp locations.

TRANSCO INC. PO BOX 4064 WEST COLUMBIA, SC

E247018

29171

GTO cable with integral sleeve , Cat. No. GTO-10 for use with neon electrode boots; Cat. Nos. SS0, EC0, SS3 and EC3 manufactured by Electrobits International. Cat. No. GTO-15 for use with neon electrode boot; Cat. Nos. SSW3, ECW3, SSW5, ECW5, SSW6 and ECW6 manufactured by Electrobits International.

SIGN FLASHERS (UYZZ2)

DUCO TECHNOLOGIES INC. 191 N GIBSON RD HENDERSON, NV 89014

E300902

Electronic sign flasher, Cat. Nos. 2AP-OSA, 2P-NX. 1. This device must be used within a suitable enclosure. 2. This device has not been investigated for loads other than incandescent types. 3. The Temperature Test was conducted in free air in a 6.5 inch square box. The maximum temperature attained was 77°C in a 25°C ambient. When provided within an enclosure smaller than the above or in close proximity to hear producing components, consideration shall be given to performing a Temperature Test.

ICM CORP. P O BOX 2819 SYRACUSE NY

E109022

13220

Electronic sign flasher, Cat. No. FPS. 1. A complete enclosure shall be provided as required in UL 48. 2. The flasher is not for field wiring and should be installed in accordance with the manufacturer's instructions. 3. The sign flasher must be mounted on an aluminum heat sink, specifically a U-shaped channel with the top 0.04 in. thick, and the sides approx. 0.142 in. thick. The side rails are 2-11/32 in. wide and the top is 2-9/16 in. wide. Minimum length is 5-5/16 in. 4. The flasher is to be connected to an incandescent lamp load not to exceed 8.3 A.

NEMCO CONTROLS INC. 10306 SAGELINK CT HOUSTON TX 77089

E161347

Electronic sign flasher, Model 2P-NX. 1. These devices must be used within a suitable enclosure. 2. These devices are rated 120 Vac, 600W for incandescent loads only. Electronic Sign Flasher, Model Nos. 3P4 followed by: 1 on 3 off-120V-8A, 1 on 2 off-120V-8A, 1 on 2 off-24V-8A, 1 on 3 off-24V-8A, 1 on 2 off-24V-20A, or 1 on 3 off-24V-20A. 1. These devices must be used within a suitable enclosure. 2. These devices have only been investigated for load types as specified below. Output Current AC Input Input Model Number (Amps max. per Voltage Current 3P4 circuit Tungsten (Volts) (Amps) Load only) 1 on 3 off-120V-8A 120 8 8 1 on 2 off-120V-8A 120 8 8 1 on 2 off-24V-8A 24 8 8 1 on 3 off-24V-8A 24 8 8 1 on 2 off-24V-20A 24 20 20 1 on 3 off-24V-20A 24 20 20 1. These devices must be surface mounted to an aluminum plate having a minimum 1/16 in. thickness with a 96.5 square inch surface area or the following measurements 10-7/8 by 8-7/8 in. or larger. Electronic Sign Flasher, SLAVE-24V-20A and SLAVE-120V-20A 1. These devices must be used within a suitable enclosure. 2. These devices have only been investigated for load types as specified below. Output Current AC Input Input (Amps max. per Model Number Voltage Current circuit Tungsten (Volts) (Amps) Load only) 24V-SLAVE-20A 24 20 20 120V-SLAVE-20A 120 20 20

79

3. 4.

SIGN COMPONENTS MANUAL (SAM)

April 21, 2008

These devices must be surface mounted to an aluminum plate having a minimum 1/16 in. thickness with a 96.5 square inch surface area or the following measurements 10-7/8 by 8-7/8 in. or larger. The SLAVE units are only suitable for use with NEMCO Model 3P4 Series controllers.

SWITCHES, PHOTOELECTRIC (WJCT2)

PRECISION MULTIPLE CONTROLS INC 33 GREENWOOD AVE MIDLAND PARK NJ 07432

Photoelectric switches, Models A105, A305 may be followed by suffix "BP". 1. Maximum load rating 8.3 A tungsten, 5 A ballast, 120 Vac. 2. Shall be reliably mounted within a suitable enclosure with lens protruding through a gasketed opening. E36102

SPECIAL USE SWITCH (WOYR2)

1. Switch body shall be enclosed within suitable enclosure. Switches in outdoor signs shall be enclosed within Listed weatherproof enclosures or shall have drain holes in the separate enclosure that acts as an accessibility barrier. 2. HP rated switch is current rated as follows:

MECHANICAL PROTECTION TUBING (YDRQ2)

1. Suitable for use as mechanical protection of insulation on low-voltage wiring. 2. Surfaces likely to bear against these materials must be free of burrs and sharp edges.

WIRE POSITIONING DEVICES (ZODZ2)

1. Refer to UL's Recognized Component Directory for Conditions of Use. 2. Not suitable for use where exposed outdoors. 3. All materials that are rated less than 90 °C shall be located not less than 1 in. from heat producing components.

80

SIGN COMPONENTS MANUAL (SAM)

E228977, pg.26 E230262, pg.46 E230358, pg.25 E231698, pg.75 E232462, pg.28 E232467, pg.32 E232725, pg.44 E235322, pg.42 E235719, pg.32 E235817, pg.75 E237485, pg.46 E237563, pg.67 E238096, pg.50 E238704, pg.60 E239061, pg.6 E239418, pg.35 E239468, pg.73 E240102, pg.12 E242084, pg.77 E242275, pg.11 E242292, pg.24 E242758, pg.48 E242790, pg.45 E242985, pg.61 E243468, pg.57 E243613, pg.7 E243993, pg.31 E245307, pg.70 E245480, pg.66 E245558, pg.3 E246878, pg.57, 69 E2470182, pg.78 E248769, pg.17, 68 E248791, pg.70 E248921, pg.59 E249079, pg.67 E249377, pg.38 E249709, pg.7 E250540, pg.40 E250540, pg.13 E250835, pg.7 E250837, pg.43 E251104, pg.27 E251315, pg.66 E251621, pg.6 E251622, pg.16 E251824, pg.31 E252547, pg.46 E252578, pg.49 E252627, pg.60 E252991, pg.77 E253134, pg.6 E25328, pg.5 E255447, pg.16 E255480, pg.43 E256424, pg.41 E256642, pg.37 E257157, pg.6 E257619, pg.44 E257957, pg.58 E257980, pg.39 E258264, pg.52 E258492, pg.23 E258512, pg.20 E258921, pg.72 E258996, pg.41 E300609, pg.36 E300902, pg.78 E301099, pg.72 E301540, pg.3 E302683, pg.6 E303143, pg.58 E303214, pg.67 E303534, pg.37 E303645, pg.45 E304298, pg.75 E304657, pg.19 E305150, pg.73 E306782, pg.58 E307621, pg.77 E307713, pg.50 E308789, pg.67 E309796, pg.73 E309814, pg.55 E310222, pg.18 E310707, pg.76 E311265, pg.62 E311557, pg.60 E311706, pg.20 E312031, pg.64 E312156, pg.14 E312392, pg.58 E313318, pg.72 E313732, pg.18 E31375, pg.75 E313829, pg.51 E314210, pg.49 E314969, pg.48 E315540, pg.70 E315636, pg.73 E315810, pg.40 E316391, pg.37 E316529, pg.35 E317700, pg.23 E318039, pg.49 E318168, pg.20 E318292, pg.7 E318820, pg.50 E318961, pg.77 E319521, pg.47 E36102, pg.79 E39591, pg.2 E52188, pg.5 E55183, pg.23 E60612, pg.43 E65361, pg.8 E65625, pg.32 E80767, pg.12 E80939, pg.18 E86197, pg.63 E90751, pg.41 E97069, pg.24

April 21, 2008

FILE NUMBER INDEX

E 192550, pg.5 E 301137, pg.74 E 307120, pg.40 E 308859, pg.42 E 309404, pg.20 E100102, pg.31 E10092, pg.3 E101623, pg.17 E104680, pg.2 E109022, pg.78 E1122656, pg.3 E125271, pg.34, 63 E125321, pg.19 E129837, pg.30 E131602, pg.32 E136722, pg.61 E136850, pg.63 E138960, pg.76 E140576, pg.73 E145519, pg.4 E146154, pg.62 E150099, pg.71 E152309, pg.33 E153777, pg.28 E156815, pg.6 E161347, pg.78 E163602, pg.62 E16382, pg.35 E173052, pg.75 E175045, pg.29 E176781, pg.7 E180252, pg.51 E184104, pg.19 E187149, pg.49 E187585, pg.4 E188273, pg.59 E188431, pg.3 E190350, pg.4 E192264, pg.69 E194105, pg.34 E199185, pg.58 E202184, pg.67 E203105, pg.4 E204188, pg.7 E205267, pg.6 E209062, pg.75 E210026, pg.17 E210684, pg.4 E211810, pg.57 E211963, pg.25 E213411, pg.55 E213579, pg.23 E215393, pg.64 E215454, pg.16 E215616, pg.6 E215877, pg.51 E215992, pg.70 E217541, pg.4 E218780, pg.27 E219167, pg.47 E219382, pg.74 E219395, pg.39 E220096, pg.55 E220165, pg.14 E220835, pg.68 E221730, pg.22 E223028, pg.39 E225580, pg.42 E225855, pg.45 E226833, pg.74 E227355, pg.37 E227766, pg.44

81

SIGN COMPONENTS MANUAL (SAM)

Gemini Inc, pg.35 Golden Valley Optoelectronics Co Ltd, pg.36 Grate Signs Inc, pg.37 Guangzhou Linong Electronics Co. Ltd., pg.37 Hanfzhou Weiliguang Technology Co Ltd, pg.37 Heatron Inc., pg.37 High Perfection Technology Co. Ltd., pg.38 Hudnut Co. Inc., pg.39 ICM Corp., pg.78 Ilight Technologies, pg.39 Illlumagraphics L L C, pg.39 Imagine Signs L L C, pg.6, 40 Intertek Corp, pg.40 Ipan LED Inc, pg.40 J & J Electronics Inc, pg.41 Jefferson Electric Inc., pg.41 Jewelite Wagner Zip-Change Inc., pg.41 Jinbo Kechuang Electronics Co Ltd., pg.3 Johnny Austin Neon Co, pg.3 Johnson Walker & Associates L LC DBA Imperial Plastics Mfg., pg.42 JS LED Power Inc, pg.42 Justin Inc., pg.42 Laminators Inc, pg.43 Lecip Corp., pg.3 LED Effects Inc., pg.43 LED Inc, pg.43 LED Sign Products, Inc, pg.44 LEDPAC, pg.44 Leotek Electronics Corp., pg.44 Lightech Electronic Industries Ltd., pg.45 Lightwild L C, pg.45 Lord Corp, pg.45 Lucere Lighting Concepts L L C, pg.46 Lumi Spec Inc., pg.46 Lumificient Technologies L L C, pg.46 Lumilens Optoelectronics, pg.47 Lumination L L C, pg.47 Lumiron Inc., pg.48 Maxbrite LED Lighting Technology L L C., pg.48, 49 McKay Data Systems, Inc., pg.6 Megapull Inc., pg.49 Milliken Industries, pg.49 Nemco Controls Inc., pg.78 Neon Tech, pg.50 Neo-Neon International Ltd., pg.5, 49 Neonvision Inc., pg.6 Newton Technologies Inc., pg.6 Nexon Co Ltd., pg.50 Nu Power Associates Inc., pg.50 Nudo Products Inc, pg.51 Odeco Electronica S A, pg.51 Olsen Gaming Inc. DBA Spectronix, pg.6 Open NV, pg.7 Optec Displays Inc, pg.7 Optoengineering, pg.51 Osram Sylvania Inc, pg.52, 55 Paige Electric Co L P, pg.77 Paltronics Inc., pg.7 Permlight Inc, pg.55 Philips Lighting B V, pg.57 Philips Lighting SSL (Canada), pg.57

April 21, 2008

COMPANY NAME INDEX

3M Company, pg.8 Abb Inc. Low Voltage Products & Systems Automation Technology Products Div. USA, pg.11 ABC Sign Products, pg.12 Actown Electrocoil Inc., pg.2 Actown-Electrocoil Inc., pg.12 Addicks Engineering & Development Co., pg.13 Adhesive Engineering & Supply Inc., pg.14 Advance Div of Philips Electronics North America Corp., pg.14 Agilight Inc., pg.16 Alcan Composites USA Inc., pg.17 Aldor Electronic Services, pg.16 Allanson International Inc., pg.2, 16 American Sun Controls - Awnings, pg.58 Amlight LEDs, pg.17 APM Hexseal Corp., pg.17 Arlon Signtech Ltd, pg.18 Artware America Inc., pg.18 Astrodyne Corp, pg.18 Astrup Co, pg.19 Atex Co. Ltd., pg.19 Atofina Chemicals Inc., Autoglas Div., pg.19 Atto Display Co. Ltd., pg.20 Axiom Power Corp, pg.20 Bisro Co. Ltd., pg.20 Blueview Electronics Optic Technology C. Ltd, pg.20 BOCA Flasher Inc, pg.22 Boyer Signs & Graphics Inc, pg.23 Bright View Electronics, pg.23 Chainzone Technology Co Ltd., pg.6 Channelume/Let-R-Edge, pg.23 Chengdu Saixing Electric Science and Technology Co Ltd, pg.23 Chicago Show Inc., pg.5 Chief Enterprises Inc, pg.24 Cooley Inc, pg.24 Daehan Ultavision Co. Ltd., pg.6 Daesang Inc., pg.25 Daktronics Inc, pg.25 Deca L L C, pg.26 Delta Electronics Inc., pg.27 Duco Technologies Inc., pg.78 Duraled Lighting Technologies Corp., pg.27 Eastman Chemical Co., pg.27 EGL Co Inc, pg.28 Electobits International, pg.77 Electraled Inc., pg.28 Electrobits Sign Systems Inc, pg.30 Electro-Luminx Lighting Corp, pg.31 E-Lite Technologies Inc., pg.29 Elkamet Kunststofftechnik GMBH, pg.31 Emeralight, pg.31 Enoch Corp., pg.32 Esco Inc, pg.32 Estar Lighting Inc., pg.32 Everbrite Inc, pg.3, 32 Excellart Sign Products L L C, pg.33 Fiberstars Inc., pg.34 France/Scott Fetzer Co., pg.3, 35 Futuremedia Displays Inc., pg.6 Futuremeia Displays Inc, pg.35

Philips Solid-State Lighting Solutions Inc, pg.57, 58 Plastoled Systems, pg.58 Polybrite International, pg.58 Power Link Electronics Co. Inc., pg.58 Precision Multiple Controls Inc, pg.79 PWM GMBH & Co KG, pg.59 Regal Supply, pg.59 RELIGHT AMERICA INC, pg.77 Relume Technologies TM, pg.60 Revolution Display Systems Inc., pg.60 Reynolds Metals Co, DBA Alcoa Cladding Systems, pg.60 Sabic Innovative Plastics US L L C, pg.61 Samik Electronic Ind. Co. Ltd., pg.7 Shanghai Jiatang Electronic Co., pg.61 Sheffield Plastics, pg.62 Shenzhen Top Century OptoElectronics Co. Ltd., pg.62 Sign/Lite Inc, pg.62 Signalex Inc, pg.63 Signalex Inc., pg.5 Signcomp, pg.63 Signstrut Ltd, pg.63 Sika Corporation, pg.64 SloanLED, pg.64, 66 Southern Mfg. Co., pg.66 Sparkle Sign Co. Ltd., pg.67 Spartech Plastics, pg.67 Spectrum Mfg Inc, pg.67 Starbright Technology L L C, pg.67 Static Controls Corp., pg.7 Strong Hand Enterprise Ltd., pg.67 Sun LED Sign Supply Inc., pg.68 Sunlite Technologies Ltd., pg.4, 68 Super Vision International Inc, pg.68 Superlite Technology Co. Inc, pg.68 T I R Systems Ltd., pg.69 Tech 22, pg.69 Techni-Lite Systems Inc, pg.70 Technolux Inc, pg.70 Technolux Inc., pg.77 Technoservice S R L, pg.4 Teledyne Lighting & Display Products, pg.70 The Bright Group Pty Ltd., pg.70 Transco Inc, pg.4, 71 Transco Inc.., pg.78 Transfotec International Ltd, pg.4, 72 Triad Magnetics, pg.73 Tridonicatco GMBH & Co KG, pg.72 Tri-Global L L C, pg.72 Tri-Mag Inc, pg.73 UJC Electronics, pg.73 Ultraflex Systems Co, pg.73 Universal Lighting Technologies, pg.73 US LED, pg.74 Ventex Technology Inc., pg.4 Verseidag-Indutex GMBH, pg.74 Virginia Optoelectronics Inc., pg.74 Voltarc Technologies Inc., pg.75 Vossloh Schwabe GMBH, pg.75 Vynex Sign Systems Ltd, pg.75 Walt Disney Imagineering, pg.75 Walton Signage Corp., pg.75 Westrim Products, pg.75 Yangzhou Yongxiang Commerce Co. Ltd., pg.76

82

Young Electric Sign Co, pg.7, 76 Zeon Corp., pg.4

SIGN COMPONENTS MANUAL (SAM)

Lampholder Adapters, pg.12 LED Border Tubing, pg.47 Rectifier, pg.49 Canopy Kits, pg.47 Class 2 Controllers, pg.22 Class 2 Drivers, pg.14, 15, 16, 18, 22, 27, 32, 35, 37, 38, 42, 45, 46, 47, 48, 53, 54, 55, 56, 57, 59, 65, 66, 70, 72, 73, 75, 76 Class 2 LEDs, pg.19 Class 2 LEDs, pg.13, 15, 16, 17, 18, 19, 20, 21, 22, 23, 25, 26, 27, 34, 35, 36, 37, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 64, 65, 66, 67, 68, 69, 70, 72, 73, 74, 75, 76 Flexible, pg.44 Class 2 LEDs Color Controllers, pg.22 Digits, pg.25 Dimmer, pg.15 Drivers, pg.25 End Cap, pg.47, 48 Leader Cable, pg.57 LED Connector, pg.47 LED Wire, pg.47, 48 Light Guide Kits, pg.47 Lighting Assemblies, pg.76 Outline Lighting, pg.57 Photocell, pg.56 Regulator, pg.23 Splice Connectors, pg.47, 48 Neon Boots End Caps, pg.70 Residential Neon, pg.30 Splice Insulators, pg.75 Electrode Receptacle Insulators, pg.71, 72 Lighting Assembly, pg.71 Polymeric neon electrode enclosures, pg.30 Polymeric neon electrode enclosures, pg.30 Power Supplies, pg.1 Indoor Type 7, pg.3, 4 Splice Insulators, pg.30 Transformers, pg.1 Indoor 7, pg.4 Indoor Type 1, pg.2 Indoor Type 2, pg.2 Indoor Type 7, pg.2 Outdoor Type 2, pg.2, 3 Outdoor Type 4, pg.2 Outdoor Type 5, pg.2, 3, 4 Outdoor Type 7, pg.3, 4 Tube Supports, pg.30 Spacer Pad, pg.30 Neon Power Suppies Dimmers Load, pg.69 Neon Power Supplies Controllers, pg.69 Dimmers, pg.69 Panels Structural, pg.17, 23, 37, 43, 51, 60 Polymeric Neon Electrode Enclosures with GTO cable, pg.77 Raceways, pg.23 Seals, pg.1

April 21, 2008

PRODUCT NAME INDEX

Adhesive Tapes, pg.9 Adhesives, pg.14, 45, 46, 64 Changing Message Signs Controllers LED, pg.7, 51 LED Controller, pg.7 LED Modules, pg.6, 7, 26, 51 Poster Scrolling Frames, pg.7 Sign Display, pg.7 Transformer Assembly, pg.77 Channel Letters Sign Body Plastic, pg.36 Channel Letters Enclosure Rated Plastic, pg.36 Fluorescent, pg.63 Plastic, pg.35 Sign Body Plastic, pg.36 Sign Faces Plastic, pg.36 Trim, pg.31, 42 Trims, pg.36, 59 Christmas Tree Fasteners, pg.1 Clocks LED Systems, Units, Kits, pg.32 Coatings Wood, pg.23 Cold Cathode Fluorescent Lighting Assemblies, pg.71 Controllers Decoder, pg.76 Incandescent Lamp, pg.69 Lamp, pg.69 LED, pg.22, 58 Class 2, pg.74 LED, pg.69 Power, pg.16 Driver Boards, pg.16 Scrolling Sign, pg.60 Sign Control System, pg.67 Cooling Fan System, pg.35 Electroluminescent Lamps, pg.31 Power Supplies, pg.31 Faces Film, pg.61 Flexible, pg.8, 18, 19, 24, 73, 74, 75 Non-Enclosure Rated Rigid, pg.27 Rigid, pg.19, 62 Enclosure Rated, pg.67 Enclosure Rated, pg.61 Not Enclosure Rated, pg.8 Flashers, pg.76, 78 Flexible Metal Conduit, pg.1 Fluorescent Grids, pg.70 Frames, pg.32, 33 Gaskets, pg.1 GTO Cable with Integral Sleeve, pg.77, 78 Insulating Bushings, pg.1 Joiner Metal, pg.24

Self Ballasted Lamp Cold Cathode, pg.77 Sign Face Tensioning System, pg.12, 49, 58, 63, 64, 71 Sign Flashers, pg.76, 78 Sign Letters LED Class 2, pg.56 Signs Fluorescent, pg.5 LED, pg.5 Signs Face Frame, pg.5 Switch Boots Push Button, pg.17 Rocker, pg.17 Toggle, pg.17, 71 Box, pg.30 Photoelectric, pg.79 Special Use, pg.79 Switch Boot Toggle Switch, pg.72, 75 Tube Supports, pg.28 Tubing Mechanical Protection, pg.79 Velcro, pg.1 Wire Positioning Devices, pg.79

Information

Sign Components Manual (SAM)

86 pages

Find more like this

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

288500


You might also be interested in

BETA
English_3-Column.qxd (Page 1)
MNL-0252 JRII
Microsoft Word - SQF 2000 Guidance Gen Operations v3 - June'06 Level 1.doc
Microsoft Word - SQF 2000 Guidance Gen Operations v3 - June'06 Level 2.doc