Read document text version

FOOTPRINT FOR TC2030-MCP PLUG-OF-NAILS (TM) CABLE ZONE REV 12/2/10 TC2030-MCP-FP MS

1. Allow clearance for finger squeeze access from the two sides shown. 2. No tracks or vias in the shaded "KEEP OUT" AREA. 3. No other track or signal within .02" of any contact pad. 4. Do not allow solder paste on the contact pads It is essential to eliminate any hole in the solder paste-mask (solder stencil) layer. If this is not possible make the contact pads thru-hole with a finished hole size of .008" or less. 5. Leg and alignment holes may be plated and used as vias but ensure minimum finshed hole size meets specified tolerances.

.100 " 2.540 mm .040 " 1.016 mm .025 " .635 mm .200 " 5.080 mm .125 " 3.175 mm .050 " 1.270 mm .050 " 1.270 mm

Allow finger access from this side

n.0935 "`.0030 n2.375 mm`.076 NON-PLATED THRU HOLE LEG LATCH HOLES

n.039 "`.003

n.991 mm`.076

2

6

NON-PLATED THRU HOLE ALIGNMENT PIN HOLES

n.031 "`.003 n.787 mm`.076 CONDUCTIVE CONTACT PADS NO SOLDER PASTE

6. To prevent purchasing confusion, please specify DNL in your BOM.

1

5

PCB BOTTOM VIEW

"KEEP OUT" AREA 1 5

Allow finger access from this side Microchip ICD / ICSP signals Pin 1: MCLR / Vpp Pin 2: Vdd Pin 3: GND Pin 4: PGD (ICSPDAT) Pin 5: PGC (ICSPCLK) Pin 6: Unused / LVP

2 6

ALLOW A .061 X .046 SQUARE AREA OF CLEARANCE FOR EACH FOOT

SIZE

FSCM NO.

DWG NO.

A

.061 " 1.549 mm .046 " 1.168 mm

SCALE

FOOTPRINT FOR TC2030-MCP-FP

SHEET 1 Of 3

REV

A

www.TAG-CONNECT.com

NOTE:

Dimensions subject to change

ZONE A

TC2030-MCP PLUG-OF-NAILS (TM) CABLE

TC2030-MCP

12/2/10

MS

.750 " 19.05 mm

.446 " 11.328 mm .131 " 3.327 mm .078 " 1.9812 mm

A

.39 " 9.906 mm

.270 " 6.858 mm

1.15 " 29.21 mm

.335 " 9.271 mm

END VIEW 6 4 2

.240 " 6.096 mm

END VIEW

5 3

1 1 2 3 4 5 6

Tag Connect inserted into PCB for programming / debugging

.078 " 1.9812 mm

SIGNAL MCLR / VPP VDD GND PGD(ICSP DAT)

TAG 6 PIN 1 2 3 4 5 6

RJ12 6 5 4 3 2 1

PCB

.300 " 7.62 mm

.2935 " 7.4549 .088 " 2.2352 mm .050 " 1.27 mm .2935 " 7.4549

PGC(ICSP CLK) NC / LVP

PART NUMBER TC2030-MCP TC2030-MCP-10

A IN 6 10 MM 152.4 254

SIZE

FSCM NO.

DWG NO.

A

SCALE

REV

TC2030-MCP

www.TAG-CONNECT.com

SHEET 2 Of 3

A

C A

Detail C

Vias between contact pads

Detail A

Do not deposit solder paste on contact pads. View Solder Paste Mask (Solder Stencil) layer in pad-stack and eliminate any hole.

B

Detail B

Traces less than .02" away from contact pad or in "KEEP OUT" area

Large componets blocking finger access to the TagConnect leg clips

Information

document

3 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

1098292


Notice: fwrite(): send of 199 bytes failed with errno=104 Connection reset by peer in /home/readbag.com/web/sphinxapi.php on line 531