Read csa_facility_piping_nao-spc-d-pf-004.pdf text version

TALISMAN

E

N

E

R

G

y

NAO ENGINEERING SPECIFICATIONS - PIPING FOR FACILITIES

CSA FACILITY PIPING NAO-SPC-D-PF-004

CSA FACILITY PIPING

Issue: 2011/01/01

Next Review Date:

June 2011

HSE/OI Staff Responsible:

Mechanical Technical Authority

Published by: Talisman Energy Inc.

APPROVALS: Tech Auth:

Eng. Auth:

VP-HSEOI:

Operational Integrity Department Calgary

Copyright is owned by Talisman Energy Inc. All rights are hereby reserved. This document (in whole or in part) may not be reproduced, stored in a retrieval system, or transmitted, in any form or means, without the prior written permission of Talisman, or as expressly permitted by law.

Note: This is an existing specification currently being used by Talisman and has not been

technically reviewed or signed off by the Technical Authority at this time. Over time, these specifications will be rebuilt and validated through a specification review process. Please ensure that you use the most current copy of the specs listed on the NAO Portal under Engineering Specifications. The Technical Authority identified on the cover sheet is the point of contact for this specification.

Attention: Paper copies are uncontrolled. This copy is valid only at time of printing, 12/15/2010. The controlled document is available on the Talisman NAO Portal.

WorleyParsons

resources & energy

TALISMAN ~J'tÏ!

ENE R G Y

eSA FACILITY PIPING MATERIAL SPECIFICATION

EXECUTIVE SUMMARY

This CSA Piping Material Specification has been developed for wellsite, facilty and station piping and therefore does not apply downstream of the pig launcher, upstream of the pig receiver or at riser locations covered by the pipeline corrosion mitigation program.

..~' i l-----.-.--------.-------f:-,t:-_

'tj¡ ---tl---------:: . "~..~.

IiI I , ~::7 I ~ I

i-----------ï

,:;.----------~1---------t i

c:' ,----.'1--.---_.-1 -----'-r----l

~~~___________I '" r/ : i ~,,~ / 1 ~----l .~c:

+ t + +

Design Methodology

The piping classes were developed to provide piping material specifications for the following CSA cold flange rated pressure classes: PN 20, PN 50, PN 100, PN 150, PN 250. For each pressure class, pipe

wall thicknesses were then calculated using the equation provided in CSA Z662-07 Clause 4.3.5.1. A

joint

factor of 1.00 corresponding to seamless and electric welded pipes, location factor of 0.625 corresponding to Class 1/ocation and Station application, temperature factor or 1.00 corresponding to temperatures below 120°C, and a specified design factor of 0.8 were used throughout this specification in the determination of the wall thickness.

CSA pipe grades chosen are reflective of material availability, cost and delivery.

Incorporating Colt Engineering

¡¡ir'¡t~Noml'cs"

"!r~'-,,,.~~

Shar.Poinl\rime Opaaling Manual\Standard SpecificationsIIBU.TlM-SPEC-EM.003 Specification - Piping Malerial

Page iii

TABLE OF CONTENTS

EXECUTIVE SUMMARy..... .................. ......... ................................................ .................... ..... ......... ........... III

TABLE OF CONTENTS..............................,................................................................................................IV

LIST OF TABLES..........................................................................................................................................V

1.

PIPING MATERIAL - GENERAL ......... ........ ...... ...... ............ .................... ........ .................. ...........1

1.1

General Scope...............................................,...............................................................................1

General Requirements............................................,............,........... ..............................................1

Codes, Standards and References .............. .............................................. ......... ...... ............ ........ 2

1.2

1.3

1.4 1.5 1.6

Design and Operating Conditions.....................................................,............................................4

Materials Identification............................................................ .......... ... .......................... ................4

Bolt Measurements.. ... ......... ........................... ......... .......... ............. ......... ......... ........ .....................6

1.7 1.8

1.9

Joining of Pipe and Swages ................... .......................................... ........ ......... .................. .......... 6

Pipe..........................................................................................,.....................................................6

Fittings ........................................................................................................................................... 6

1.10 Flanges .......................................................................................................................................... 7

1 .11

Valves .....................................................................................................................,...................... 7

1.12 Line Reductions .................. ....................... ......... ....... ..................... ......... ......... ...................... ....... 8 1.13 Branch Connections ................................,..........................................................................,..........8 1.14 Small Piping Subject to Vibration................................ .......... ..... ...... .......................... ........... .......8 1.15 Thread Compound .............. ......... ........... ............................. .................... .... .................. ........ ........8 1.16 Seal Welding..............,................................................................................................................... 9

1.17 Pipe Bends.....................................................................................................................................9

1.18 Postweld Heat Treatment Requirements................ ............................................ ........................... 9

1.19 Inspection and Testing................................................................................................................. 10

1.20 Pipe Supports .............. ......... ...... ............ ......... ......... .................................. ..................... ............10

1.21

2.

Branch Connection Tables ..........................................................................................................11

PIPING MATERIAL - PIPING CLASSES.................................................................................... 13

2.1

Pipe Class Index..........................................................................................................................13

Notes Referenced in Line Classes .............................................................................................. 14

2.2

Incorporating Coli Engineering

'""e,,"'¿ omics

~~£f~$.""~

..",. N ",.

SharePointlPrime Operating Manual\Slandard Sp.c~icetionsUBU-TLM-SPEC.EM-03 SpeficaUon- Piping Material

Page lv

LIST Of TABLES

Table 1: Thread Compounds.................................................................................,....,........."...."...............9

Table 2: Branch Connection Chart # 1....... ......................... ............ ........................................................11

Table 3: Branch Connection Chart #2, Sour Vibration Servìce................................................................. 12

Table 4: Pipe Class Index Table ............................................................................................................... 13

Incorporating Colt Engineenng

ë" Nomics ..~ ii"¡;~~Ì;i

."R,,~~~1;'~

SharePoinl\Prime Operating Manual\Slandard Spe",ficalions\IBU.TLM.SPEC.EM.003 Specification - Piping Material

Page v

1.

PIPING MATERIAL m GENERAL

1.1

1.1 .1

General Scope

This specification describes the basic requirements for tiie application of the Talisman/WorleyParsons Calgary Prime Alliance CSA Piping Material Specifications and the minimum requirements of these specifications.

This specification does not replace engineering design and engineering

1.1.2

responsibility of the designer in its use and application. It is intended that

the user is familiar with the design requirements outlined in the Acts, Regulations and Codes described within this document.

1.1.3

This specification covers facility piping applications that are to be designed and built using the CSA Z662-07 design code.

This specification is to be used in conjunction with Section 3 of Talisman ASME Piping Specification IBU-TLM-SPEC-EM-003.

The standard covers new construction and modifications to piping systems on and in Talisman Energy's facilities.

1.1.4

1.1.5

1.1.6

This piping specification requires review when new issues of the

underlining codes are issued and come into effect. If no reviews are performed in a continuous 3 year period a review will be performed based on general use and application only.

1.1.7

Designs that do not comply with this specification require a Technical Deviation Notice Form, to be completed and signed by the Prime

Mechanical Lead.

1.1.8

This piping specification does not cover line classes with B31.3 or AP I

designations. For line classes with B31.3 designations, refer to IBU-TLMSPEC-EM-003.

1.2

1.2.1

General Requirements

In the event of conflict within this specification or between this specification, the purchase order, the accompanying data sheets and any

other specifications, the contractor shall obtain a written resolution before

proceeding with the work.

1.2.2

Where City, Provincial and/or Federal Codes conflict with this specification, the responsible engineer shall be made aware of any such conflict.

Incorporating Colt Engineering

é. . N ." ~"~"*'~ omics

~-A 't~~ '",~, Page 1

SharePoin\IPrime Operating Manual,Slandard SpeciflcaliCns~BU.TLM.SPEC-EM-03 Specifcation - Piping Material

1.2.3

All standard drawings, codes and specifications referred to, directly or implicitly, or listed throughout this specification shall form part of this

specification.

1.2.4

Items specified or referenced by manufacturer and figure number are not intended to exclude equal items offered by other manufacturers. Products

of reputable manufacturers and of comparable type, quality and

characteristics may be substituted with written approval of the responsible

engineer.

1.3

1.3.1

Codes, Standards and References

Unless otherwise noted in the individual line classes, this specification is based on and is in accordance with the following codes and regulations.

Canadian Standards Association (CSA)

1.3.1.1

. CSA Z662 "Oil and Gas Pipeline Systems"

. CSA Z245.1 "Steel Pipe"

. CSA Z245.11 "Steel Fittngs"

. CSA Z245. 12 "Steel Flanges"

. CSA Z245.15 "Steel Valves"

1.3.1.2

Government of Alberta

. Safety Codes Act

. Pressure Equipment Safety Regulation

1.3.1.3

Government of British Columbia

. Safety Standard Act

. Power Engineers, Boiler, Pressure Vessel and Refrigeration Safety

Regulation

Incorporatin3 Call Engineering

r.t;~~",?.t'Noml'(s" ,,,,~i2

SharePoinl\Prirre Operating M.nual\landard SpecificationsllBU- TLM.SPEC.EM.OO3 Specification - Piping Material

Page 2

1.3.1.4

Government of Saskatchewan

.. The Boiler and Pressure Vessel Act and Regulation

1.3.1.5

American Society of Mechanical Engineers (ASME)

.. ASME B 16.11 "Forged Steel Fittngs, Socket-Welding & Threaded"

.. ASME B16.5 "Pipe Flanges and Flanged Fittings"

.. ASME B 16. 9 "Factory Made Wrought Steel Bultweldirig Fittngs"

.. ASME 836.10M "Welded and Seamless Wrought Steel Pipe"

.. ASME 816.25 "8uttwelding Ends"

.. ASME 816.36 "Steel Orifice Flanges"

.. ASME 816.20 "Metallic Gaskets, Ring Joint Gaskets and Grooves for

Steel Pipe Flanges"

.. ASME 816.48 "Line 8lanks"

.. ASME 816.34 "Valves - Flanged, Threaded, and Welding End"

1.3.1.6

1.3.2

"Piping Design and Layout Specification" COL T GS903-01

All standards, specification and codes will be latest edition as published on

the day of signing of the contract unless otherwise specified in the contract.

1.3.3

Substitution of a material with a higher CSA grade material than that listed in this specification is permitted. However, all other material substitutions

are not permitted unless advance written approval is obtained from the

responsible engineer. It should be noted that different weld procedures may be required when joining dissimilar grade material.

1.3.4 1.3.5

All materials shall be new, clean and unused and fabricated from new

materials.

For brevity, the initials of the society to which the codes refer, are omitted

in the piping classes. For example, Z662 refers to CSA Z662, A106 refers to ASTM A106, etc.

1.3.6 1.3.7

For brevity NACE shall refer to NACE MR0175/ISO 15156 latest edition

When the installation or use of materials specified in this document may

pose safety or health problems, the manufacturer/supplier shall provide ~1i"~';' omics i£.~.~"", :aJ(

Incorporating Colt Engineering

..' . N . ~

SharePoinllPrime Operating ManuallSlandard Specifjca:ionsII8U.TLM.SPEC.EM.003 Specificalion - Piping Malerial

Page 3

WorleyParsons Calgary with current information regarding any known problems associated with the use of the manufacturer/supplier's product.

The manufacturer/supplier shall also recommend protective measures to be employed in their safe utilization. Contractor shall establish appropriate

safety and health practices and determine the applicability of regulations

requirements prior to use.

1.3.8

All materials shall be asbestos free.

1.4

1.4.1

Design and Operating Conditions

For definitions of design and operating conditions see Colt Pieing De, and Layout Specification GS903-01.

A service will be designated as sour if the design conditions match or exceed the criteria as set out in CSA Z662-07 Clause 16.2 or applicable

1.4.2

provincial governing body.

1.4.3

If a service is designated as sour, the systems must be designed in

accordance with all the requirements defined in CSA Z662 Section 16, latest edition. Refer to Talisman Sour Service Spec ES1.A408 for additional

sour service requirements.

1.4.4

All piping systems including supports shall have a MDMT (Minimum Design Metal Temperature). The MDMT is defined as the minimum metal design temperature at which components are subjected to internal or external pressures or stresses. All required Cat II piping materials shall be impact tested according to CSA Z662 Cat Ii (_45°C) requirement.

1.5

1.5.1

Materials Identification

All materials not covered by the piping material specifications shall be

clearly identified with an identification number on the P&ID's, the piping drawings and the isometrics. All items with an identification number shall be recorded on a specialty item (SP) list as a part of the drawing package. The identification number shall be permanently attached to the item with a stainless steel tag or nameplate.

1.5.2

All valves and piping components shall bear tlie normal identification markings as required by CSA, ANSI, ASME, ASTM, MSS or other applicable standards and specifications.

shall provide the heat number for the QC package for all materials supplied

1.5.3 CE-Franklin shall hold mill test reports on behalf of Talisman-Energy and

to Talisman-Energy by CE-Franklin. All materials purchased from suppliers

Incorporating Coil Engineering E(~:¥ N omics

SharePolntlPrime Operabng Manual\Standard Specifica,ions\IBU.TLM.SPEC.EM-003 Specificalion - Piping Material

Page 4

other than CE Franklin shall be supplied with the mill test reports for the

QC package.

1.5.4

Each individual length of pipe shall, as a minimum, be marked with the applicable CSA grade or ASTM standard and wall thickness: i.e. CSA GR241 SCH8D. These markings shall be applied continuously throughout

each full length of pipe.

1.5.5 1.5.6

All markings on stainless steel and alloy piping shall be free of chlorides and metals.

Wall Thickness Calculations and Corrosion Allowance

ø Wall thickness calculations are based on CSA Z662-07 and Alberta Regulation AR 9112005 (Clause 16) where design stress levels may not exceed 50% SMYS for all sour above ground piping.

ø A computerized calculation sheet for determining wall thicknesses is

available on the Mechanical Engineering Computer Network and Talisman SharePoint Site.

ø Tiie corrosion allowance to be used is specified in the individual line

classes.

1.5.7

Pressure and temperature limits indicated in the individual Line Classes are based on the lesser of the maximum allowable flange rating as per CSA Z245.12 or ASME 816.5 for the particular material group. All piping component wall thicknesses specified in each Line Class are based on the

lesser of either the allowable flange pressure rating or the allowable stress

of the piping component found within the temperature limits of the Line Class. Allowance has been made for the stated corrosion allowance, depth of any threads, and manufacturer's mill tolerance.

1.5.8

Piping component wall thicknesses do not include any additional thickness

that may be required to compensate for such design considerations as

thermal loads, live loads, hydraulic shocks, or loads and forces from other causes, all of which must be given consideration when designing piping

systems.

1.5.9

Unless otherwise specified, all pressures specified in the individual Line

Class are positive pressure. All piping subjected to a negative pressure shall be investigated on an individual basis since the engineering design specified in the applicable Line Class mayor may not be suitable.

1.5.1 D

All CSA Material shall be low temperature (-45°C) category II materiaL.

All A35D-LF2 forgings shall be CLASS 1.

~.'...t".i(~ omics ';'~~~'-~-" """.".'N . ."

Page 5

1.5.11

Incorporating Colt Engineering

SharePoinllPrime Operating Manual\landard speclncaiions~BU.TU,\.SPEC.EM.003 Specification - Piping Materal

1.6 Bolt Measurements

1.6.1 Machine bolt length shall be measured from the bearing surface of the head

to the extreme point.

1.6.2 Stud-bolt length shall be the effective thread length (not including points).

1.6.3 Calculated bolt lengths shall be rounded up in increments of 1/4", to

commercially available lengths.

1.7 Joining of Pipe and Swages

1.7.1 Pipe-to-pipe joints shall be made as follows:

o Threaded end pipe: Use couplings with taper threads in accordance with ASME B16.11. Unless otherwise specified, the threads shail conform to ASME B1.20.1 (pipe threads, general purpose (inch).

o Plain end (cut square or beveled) pipe NPS 1 1/2" or smaller: Use socket-welding couplings in accordance with ASME 816.11.

o Beveled end pipe NPS 2" and larger: Butt-weld in accordance with CSA 2662, latest edition.

o The above shall also apply when joining swage nipples to pipe.

1.8

1.8.1

Pipe

Pipe sizes 3/8", 1 1/4",2 1/2", and 5" shall not be used, except where required to connect to equipment. Conversion from these non-standard

sizes to standard piping shall be as near to the equipment as possible.

1.8.2

All carbon steel pipe dimensions must conform to CSA 2245.1 for CSA

pipes and ASME 830.1 OM for all otlier pipes

1.8.3

Design pressure for pipe made to a standard or specification other than recommended in CSA 2662-07 shall not exceed the pressure corresponding to 72% of SMYS of the pipe (Clause 4.3.5.4).

1.9

1.9.1

Fittings

Fittings shall be taper bored in accordance with CSA 2245.11 for CSA

fittings and ASME 831.3 for all other fittings if the thickness exceeds the

pipe wall thickness by more than 1.6 mm. When fittings of greater wall thickness than specified are supplied, approval in writing must be obtained

Incorporating Colt Engineering

~r¿-~",";~û:

~". Ø"t;;~ om I cs

.,;" -N . ,.

SharePointlPrime Operaling ManuallStandard SpecífictionsUBU.TLM-SPEC.EM-003 Spafic3tion - Piping Material

Page 6

¡"

from the responsible engineer. The Stress engineer must be immediately informed of this substitution.

1.9.2

Miters shall not be used unless specified by the responsible engineer.

Where specified, miters shall be as follows:

. 45° turns Two piece - one weld o 90° turns Three piece - two welds

o 1-1/2 diameter

radius

1.9.3

Short-radius butt-welding elbows shall not be used unless specified by the responsible engineer. When specified they shall be limited to 80% of the maximum allowable working pressure when subjected to pulsating

pressures.

1.9.4

CSA and ASME steel butt-welding fittings must be supplied in accordance with CSA 2245.11 and ASME 816.9 respectively. The out of roundness of fittings and elbows shall not exceed 4% of the nominal diameter of the fitting. The butt-weld connection and all other tolerances shall be in accordance with 2245.11 for CSA fittings and 816.9 for ASME fittings. Sharp edges on the back of elbows are not acceptable.

1.9.5

Where a reducing weld tee, or weld reducer is joined to pipe of different

schedules, the fitting selection shall be based on the heaviest pipe

schedule. The fitting end attached to the lighter wall pipe shall be taper bored to suit.

1.9.6

Reducing butt-welding fittings shall have ends specified to the same schedule or weight. The schedule or weight shall not be less than that required for any end of the reducing fitting.

1.10

1.10.1

Flanges

All CSA specified flanges shall conform to CSA 2245.12, All others shall conform to ASME 816.5.

Specified CSA Orifice flanges shall have the flange conform to CSA Z245.12 with the orifice machined to ASME 816.36. Weld neck orifice

flanges shall be specified with bore to match the pipe inside diameter.

1.10.2

1.11

1 .11 .1

Valves

Valves shall conform to CSA Z245.15, Section 3 of IBU-TLM-SPEC-EM-003 and any additional requirements listed in this specification.

ìf;~'""""Nom'I(S'~

K,,a,.~~,,-~-

Incorporating Colt Engineering

SharePoinl\Prtme Operating ManuallStandard SpecificalionsIlBU-TLM.SPEC-EM.003 Specification - Piping Material

Page 7

1.12

1.12.1

Line Reductions

When reducing to or from a screwed/socket weld fitting 1 1/2" NPS or smaller, use a swage nipple for the small end.

1.12.2

When reducing in butt-welding construction 2" NPS and larger, use a butt-

welding reducer for the small end. The reducer schedule sl1all match the pipe schedule at both ends.

1.12.3

Stub-in connections into weld-caps or heads are not permitted.

1.12.4

Connections into a flat surface require the use of flat-olet.

1.13

1.13.1

Branch Connections

All branch connections must be made in accordance with the applicable referenced branch connection table in the individual piping material class.

1.13.2

If reinforcing pads are required. They shall be supplied with a 1/4" drilled and tapped tell-tale hole to allow pressure testing of the pad. After testing

the hole can be filled with grease.

1.14

1.14.1

Small Piping Subject to Vibration

All piping branches subject to vibration, and smaller than 1 1/2", shall be reviewed to determine the need for gussets.

All gussets shall be installed in accordance with Colt Standard Drawings EP303-2505 and 2506.

1.14.2 1.14.3 1.14.4

Valves must be close-coupled to the take-off connections.

Close nipples and fully threaded nipples shall not be used.

1.15

1.15.1

Thread Compound

Thread compound shall be used for all threaded connections that are not seal welded.

1.15.2

Teflon tape shall not be used for any threaded connections.

Table 1 indicates thread compounds suitable for the various services listed.

1.15.3

Other compounds suitable for service may be selected.

Incorporating Colt Engineenng

E(:~4Nomi(s

Page 8

SharePcin:\Prime Operatlng Manua/\Standard Speclfications\lBU-TLM-SPEC-EM-003 Specification - Piping Material

Table 1: Thread Compounds

Service

Sour and sweet hydrocarbon service

Lube oil, Seal oil

Thread Type

Temperature Range

-73cC to 260.C

Thread Compound

Jetlube TF-15(A)

PipeTHRD

Pipe THRD Pipe THRD Pipe THRD

-45cC to 200'C -73cC to 260'C

,45cC to 260.C

Locktite PST Pipe seal 567(A)

Jetlube TF-15IA)

Jetlube V-2(A)

Sulphuric Acid

Utility Air with Potable Water

Thread anti seize lubricant

Sour and sweet hydrocarbon service

External bolts

Pipe THRD

-45.C to 400.C

OCG to 650.C

Locktite Nickel anti seize #771(A)

UCAR Grafoil GTS sealant paste(A)

. .

NOTE: (A) or approved substitute, current venàor datasheets are available in Appendix B

See Appendix B of IBU-TLM-SPEC-EM-003 for the thread compound vendor specifications and data

sheets.

1.16

1.16.1

Seal Welding

Seal welding is only permissible for threaded connections when approved

by the responsible engineer and specified on the isometric.

1.16.2

Seal welded joints shall be wrench tightened and then backed off one half

turn before welding.

1.16.3

Thread compound or tape shall not be used on joints to be seal welded. Do

not seal weld plugs on valved process vents and drains.

1.17

1.17.1

Pipe Bends

Pipe bends shall be made according to Colt Standard 01.

1.17.2

Bending radius of metallic pipe shall be a minimum of five times the

nominal diameter.

1.17.3 1.17.4

Heat treatment requirements shall be determined in accordance with CSA.

Short radius and field bends may only be used with written approval from

the responsible engineer.

1.18

1.18,1

Postweld Heat Treatment Requirements

Postweld heat treatment per Code. Weld procedure qualification (WPS), with supporting procedure qualification record (POR), to be qualified by impact testing as required by relevant Code (ASME 831.3 or CSA Z662). All welds in vibrating service shall be stress relieved.

Incorporating Colt Engineering

- "'N . ".

ii",*'~~'1, omics

;q(r~~!i~,,~

SharePoinf\Prime Operating Manuar\tandard Specificalions\IBU-TLM-SPEC.EM-ù03 Specification - Piping Material

Page 9

1.19

1.19.1

Inspection and Testing

All welds shall be radiographed in accordance with the requirements of CSA

l662 as a minimum.

Acceptance criteria shall be those for the applicable Codes and Standards.

1.19.2

Ultrasonic testing shall be conducted on welds that can not be radiographically examined at Owner's option. Acceptance criteria shall be as per the applicable Codes and Standards.

Charpy Testing Impact testing shall be in accordance with CSA l662.

Hardness Testing

o If micro hardness testing is required it shall be performed in accordance with the

1.19.3 1.19.4

requirements of ASTM E384.

o All welding procedure specifications/welding procedure qualification records

(WPS/PQR's) shall contain hardness test results.

o PQR hardness testing shall be carried out by the Vickers Microhardness test method.

o Acceptance criteria for Vickers hardness testing shall be per CSA.

o Hardness testing shall be carried out on a sample cross section and shall include three readings each in the HAl, weld, and base material, at 0.25t from each surface and at

D.5t.

1.19.5

Pressure testing of piping shall be 1.5 times the MOP for each line class.

CSA Z662-07 Clause 8.6 stipulates that "where practical," pipe spools should be tested to produce the same hoop stresses as would be produced in the absence of erosion and corrosion allowances; this would result in hydro test pressures in excess of 1.5 times the cold rated flange pressure therefore creating hoop stresses in excess of 75% of SMYS of the material.

It was deemed impractical in facility piping to resolve the above issue by

derating the operating pressures or changing flanges for this reason 1.5 times the MOP will be used as the test pressure.

1.20

1.20.1

Pipe Supports

Welded shoes can only be used when the calculated hoop stress is less than 50% of the SMYS of the materiaL.

Incorporating Colt Engineering

~li¡~:(t~Nomics

Paga 10

SharePoiiitlPricne Operating Manualllandard SpocijicationsUBU- TlM.SPEC-EM.(3 Spacifcation - Piping Malerial

1.21 Branch Connection Tables

TABLE 2: BRANCH CONNECTION CHART # 1

BRANCH SIZE

~lI

*"

O'LET

1"

1Y:"

2"

3"

4'

6"

8"

10"

12"

12"

O'LET

O'LET

O'LET

WOL

WOL

INL

RT

RT

RT

RT

T

10"

O'LET

O'LET

O'LET

O'LET

VVOL

WOL

RT

RT

T

8"

O'LET

O'LET

O'LET

O'LET

WOL

WOL

RT

RT

T

l. N

Vi

6"

O'lET O'lET

O'lET

O'LET

O'lET

O'LET

O'lET

O'LET

O'lET

O'lET

WOL

RT

RT

RT

T

c: l. ci

4"

RT

T

~ :i

3"

O'LET

O'lET

O'lET

TT

O'lET

RT

T

2"

O'LET

T(3)

T

"'~..

TT

TT

IT

1"

TT

TT

TT

~..

W'

IT

TT

TT

NOTES:

1)

The responsible engineer must approve this branch chart for each applicatIon

2)

3) 4)

Review the suitability of weldolets for lines in pulsating seNice

Use full size 2" welding tee and 2" x 1.5" swage

Refer to Individual

line list for usage restrictions.

Incorporating Colt Engineering

ti~æ'¡r;~ Nomi'cs'"

~~..".;,;~.

SharePoinllPrime Operating Manual\tandard Sp"",f,calionsIIBU-TLM.SPEC.EM-003 Specification - Piping Malenal

Page 11

TABLE 3: BRANCH CONNECTION CHART #2, SOUR VIBRATION SERVICE

BRANCH SIZE

N

W

ëñ

0: w

i:

.0

W

:i

'II12"

10"

%"

7:"

1"

.. 1'/,"

O'LET

2"

3"

4"

6"

a"

10"

12"

O'LET

WOL

WOL

WOL

RT

RT

RT

RT

T

0 UJ

S

O'LET

O'LET

WOL

WOL

WOL

RT

RT

T

a"

6"

0 .. .. -:

O'LET

O'LET

WOL

RT

RT

T

O'LET

O'LET

WOL

RT

RT

T

I-

4"

0 Z

O'LET

O'LET

RT

RT

T

3"

O'LET

O'LET

RT

T

T

2"

O'LET

T (3)

1%"

TT

TT

1"

n

TT

TT

TT

TT

n n

n

%..

~..

NOTES:

1)

The responsible engineer must approve this branch chart for each application

Review the suitability of weldolets for lines in pulsating service

2)

3)

Use fiill size 2" welding tee and 2" x 1.5" swage

Refer to Individual

4)

line list for usage restrictions.

incorporating Colt Engineering

ii'~''''No . ~ .=!J.~" mics

.':~.'(,,,~d,

SharePGin:lFrime Cperaling Manual\landerd SpecificalionsIIBU.TLM.SPEC-EM.003 Specification - Piping Malerial

Page 12

WorleyParsons

ENE R G Y

TALISMAN .,m::m~...

resources & energy

CSA FACILITY PIPING MATERIAL SPECIFICATION

2. PIPING MATERIAL - PIPING CLASSES

2.1 Pipe Class Inde)(

TABLE 4: PIPE CLASS INDEX TABLE

PMG

Service

Rating I

CA

prrmin. Limit in

kPa ¡OC

prrmax. Limit in

kPa lOG

Joint

Flange Facing

ZAC2

PN 201 RF

1.6 mm

1900! -46

1694/120

0.5" - 1.5" THRD

SWEET HYDROCARBONS (L T) Sweet Hydrocarbons, Fuel Gas, Process Drain and Vent, Propane Refngerant, Methanol, Natural Gas, Lube Oil, Seal Oil, Control Oil

2"-12" BW

PN 50 IRF

1.6 mm

I

ZBC2

SWEET HYDROCARBONS (L T) Sweet Hydrocarbons, Fuel Gas, Process Drain and Vent, Propane

4960/-46

4600! 120

0.5 - 1.5" THRD

2"-12" BW

Refrigerant, Methanol, Natural Gas

ZCC2

SWEET HYDROCARBONS (L T) Sweet Hydrocarbons, Fuel Gas, Process Drain and Vent, Propane

PN100/RF

1.6mm

9930! -46

9200/120

0.5 - 1.5" THRD

2"-12" BW

PN 1501 RF

Refrigerant, Methanol, Natural Gas

ZOC2

SWEET HYDROCARBONS (L T) Sweet Hydrocarbons, Fuel Gas, Process Drain and Vent, Propane

1.6mm

148901-46

13796! 120

0.5 - 1.5" THRD 2" -12" BW

Refrigerant, Methanol, Natural Gas

ZEC2

SWEET HYDROCARBONS (L T) Sweet Hydrocarbons, Fuel Gas, Process Drain and Vent, Propane Refngerant, Methanol, Natural Gas

PN 250! RF

1.6mm

24820! -46

22996! 120

0.5 -1.5" THRD 2"-12" BW

Incorporating Coil Engineering

~~~$""i.n!t- N . ';'

P~gc 13

!í;;i".~,ii omics

SharePalnllPrime Operating Manual\landard Specircatians\IBU-TLM-SPEC-EM-003 Specificauan Piping M~icri~1

WorleyParsons

resources &. energy

TALISMAN

ENE R G Y

C5A FACILITY PIPING MATERIAL SPECIFICATION

2.2

1.

Notes Referenced in Line Classes

PWHT per Code. Weld procedure qualification (WPS), with supporting procedure qualification record (PQR), to be qualified by impact testing as required by relevant Code (ASME B31.3 or CSA Z662). All welds in vibrating service shall be stress relieved.

Design pressure for pipe made to a standard or specification other than recommended in CSA Z662-07 shall not exceed the pressure corresponding to 72% of SMYS of the pipe (Clause

2.

4.3.5.4).

3.

Bore to match pipe.

Specify olets as branch schedule and size by header size. Refer to Branch Connection Chart #1. Use Branch Connection Chart #2 for Sour Vibration Service.

Small bore flanged valve shall be used for instrument connections, vents and drains only.

Install in horizontal position with cover up only.

4.

5.

6. 7.

8.

Install in horizontal position with cover up or vertically with flow upwards only.

In horizontallínes, split-disc wafer type check valves shall be installed with the shaft in the

vertical position.

9.

For Valve material description and purchase details refer to Section 3 of Talisman ASME Piping Material Specification IBU-TLM-SPEC-EM-003.

10.

Contractor or Vendor's welding procedure qualification (WPS), with supporting procedure qualification records (POR), shall ensure that weld hardness does not exceed 22 HRC. The location and number of hardness impressions shall be as specified in the referenced code for sour service applications and shall include the weld root, heat-affected zone (HAZ), weld cap and parent metal. Hardness readings shall be documented and records submitted to Talisman (TLM). All welds in vibrating service shall be stress relieved.

11. Threaded fittings shall not be used on main process piping in sour service applications. Threaded fittings may be used on branches which have been isolated from the main header with a flanged valve or as approved by the responsible engineer. Where threaded forged fittngs are specified, pressure ratings shall be as outlined in ASME B16.11

12. Socket-welded valves shall be used in sour service applications. Combination-end valves (SW x NPT) may be used for vents, drains and instrument connections only.

13.

Figurc-B Blank

Paddle Blaiik

Paddle Spacer

Figure 8: ASME 816.48 Line Blank Types

14. Line blanks impact testing requirement as per ASME B31.3 Paragraph 323.2.

Incorporating Coil Engineering

SharePolnllPrime Operal'ng MaiiuallStaiidard Specificalions~BU-TLM-SPEC-EM-003 Speclilcation Piping t~aiariaJ

t..":æ.;....'G.",.' N om' ..t1$~..¡~~~

i (S'.

page '4

WorleyParsons

resources & energy

-

TALISMAN

ENE R G Y

CSA PI PING MATERIAL SPECIFICATION

Rev.

SWEET HYDROCARBONS, FUEL GAS, PROCESS DRAIN AND VENT, PROPANE REFRIGERANT, METHANOL, NATURAL GAS,LUBE OIL, SEAL OIL, CONTROL OIL

ZAC2

í

June 29, 2009 Page 1 of 2

CSA CLASS

~~BOVBGRÖÛND*tlÖWITËMRERATÚRE~SWEEnHYÐR00AR80N~Wn~~~~~~g~ ~BRESSnRE:'ilIMITS*~~iÆfff;§4rlfD~t gfCSA¥l662rÔi~~"áilJ1/¿

1,900 kPag 1,694 kPag

@ @

(CSA Z662-07 CATEGORY " SERVICES)

-45/38°C 120°C

PN 20

Corrosion Allowance: 0.0625" (1.6 mm) Radiooraohv: 15%

Class Location Designation: Class 1 OesiQn Factors: F=0.8, L=0.625, T=1.00, J=1.00

RATING

XS

IASME 150) PWHT: Notes 1 Branch Table: 1

liTEM Pipe

ASME B36.10 CSAZ245.1

SIZE. NPS

0,5 TO 1.5

JOINT

PE

BW

MATERIAL

NOTES

2

ASTM A333 Gr 6, SMLS

CSA 2245.1 Gr 241, Cat II, -45°C

2TO 12

STD

150 CLASS 150 CLASS 150 CLASS

150 CLASS 150 CLASS

Flange

ASME B16.5

2TO 12 2TO 12

RFWN

RFBLlND

RFBLlND RFBLlND

ASTM A350.LF2 Class 1 ASTM A350-LF2 Class 1

ASTM A350-lF2 Class 1, THRD Bore 0.5"

3

Reducing Flanges

ASME B16.5

2T02 2T02 2T02

2TO 12

0.5 TO 1.5

ASTM A350.lF2 Class 1. THRD Bore 0.75'

ASTM A350-LF2 Class 1, THRD Bore 1.00'

RFHUB

RFWN

Orifice Flanges

li,SME B16.36

300 CLASS

ASTM A350-LF2 Class 1,2 - y, THRD Taps

3

Fittings

fI.SME B16.11

3000 #

SAME

THRD

AS PIPE

ASTM A350-LF2 Class 1

ASTM A420,WPL6

3

fI.SME B16.9

2TO 12

0.5 TO 1.5 0.5 TO 1.5 0.5 TO 1.5 0.5 TO 1.5

BW

Union MSS-SP-83 Nippie ASME B36.10

3000#

XS

THRD THRD

ASTM A350-LF2 Class 1

ASTM A333-6, SMLS, 100mrn LG

ASTM A420-WPL6

Swage

MSS SP.95

XS

3000 #

THRD

THRD

BW

Diet

MSSSP-97

Plug ASMEB16.11 Line Blank

AS

2T04

0.5 TO 1.5

2 TO 12

ALL

ALL

SAME AS PIPE

ASTM A350,LF2 Class 1 ASTM A350-LF2 Class 1

ASTM A350-LF2 Class 1, Solid Round Head

4 4

MNPT

150 CLASS

ME B16.48

RF Fig, 8

ASTMA516-70N

ASTM A 193-B7M, Stud Bolt

13,14

Bolt

ASME B16.5

Nut ASME B16,5

ASTM A 194-2HM

150 CLASS

Gasket

AS

ME B16.20

ASME 816.20

2TO 12 2TO 12

RF

3mm THK, 316 SS Graphoil filled, CS Outer ring

300 CLASS

RF

3inm THK, 316 55 Graphoil filled, CS Outer ring

Incorporating Colt Engineeriri

SharePoinllPrtme Operating Manual\Slandard SpecificationsIIBU-TlM-SPEC-EM-D03 Specification - Pi;ing Material

f;;;r~""'Noml'cs'. .,:;~",'1,,i

WorleyPairsons

resources & energy

'~i"'SlEe'?

TALISMAN

ENE R G Y

CSA PIPING MATERIAL SPECIFICATION

Rev.

ZAC2

1

June 29, 2009 Page 2 of 2

CSA CLASS

:iAÍ3ÖVÐ;GHÖUND~J£ÖW¡\'fEMHERATIJRË~$W~Er¡HVÖRÖCARBÖN$r

SWEET HYDROCARBONS. FUEL GAS, PROC::SS DRAIN AND VENT, PROPANE REFRIGERANT, METHANOL, NATURAL GAS,LUBE eii, SEAL OIL, CONTROL OIL (CSA Z662-07 CATEGORY II SERVICES)

~ ~;IlRE$$URE;lliMíT$~~i;~¡!¡fi~~~i ¥rø$Ai;Z662~07&)~;r¡~'¿$

1,900 kPag

1,694 kPag

@ @

-45/38°C 120°C

PN 20

1

Corrosion Allowance: 0.0625" (1.6 mni) Radioaraohv: 15%

Class Location Designation: Class Desian Factors: F=0.8, L=0.625, T=1.00, J=1.00

1

(ASME 150) PWHT: Notes 1

Branch Table:

VALVES (ASME 816.5,816.10,816.11, B16.25, 816.34, eSA Z245.15)

I TYPE

Gate Valve

SIZE, NPS

RATING

JOINT

BODY MATERIAL 1

VALVE TYPE

TAG

NOTES

API 600, 602; CSA Z245.15 0.50 TO 1.50

API BOO

2T012

Globe Valve

PN 20 (150 CLASS)

THRD RF

ASTM A350-LF2 CI.1I Solid Wedge

ASTM A352-LCC 1 Flexible Wedge

GIB30

GAB41

9

9

API 602; CSA Z245.15

0.50 TO 1.50

API BOO

THRD

RF

ASTM A350-LF2 CI.1 1 Swivel Disc ASTM A352-LCC 1 Swivel Disc

L1B30

9 9

2T04

Check Valve API 594, 602; CSA Z245, 15 0.50 TO 1.50

PN 20 (150 CLASS)

LAB40

API 800 API 800

THRD THRD

ASTM A350-LF2 eLi

1 Ball Type

CIB30

CIB31

050 TO 1.50 2TO 12 2TO 12

Ball Valve

API 608; CSA Z245.15

ASTM .A.350-LF2 CI.1 1 Horizontal Lift Type

PN 20 (150 CLASS)

RF RF

ASTM A352-LeC 1 Swing Type

ASTM A352-LCC 1 Wafer Type

CAB42

PN 20 (150 CLASS)

eAB43

6,9 6,9 7,9 7,8,9

0.50 TO 1.50

PN 250 (1500 CLASS)

PN 20 (150 CLASS) PN 20 (150 CLASS)

THRD

ASTM A350-LF2 CI.1I Regular Port

ASTM A352-LCC 1 Regular Port

BEB30

BAB40

BAB41

9 9 9 9

2T08 2T08

10TO 12 10TO 12

RF RF RF RF

ASTM A352-LCC 1 Full Port

ASTM A352-LCC 1 Regular Port

PN 20 (150 CLASS) PN 20 (150 CLASS)

BAB40G

ASTM A352-LCC 1 Full Port

ASTM A352-LCC 1 Regular Port .A.STM A352-lCC 1 Full Port

,A,STM A352.LCC 1 Regular Port

BAB41G

BAB42

BAB43

9

9 9

Ball Valves for use in liquid Services ONLY (c/w self.relieving seats) RF PN 20 (150 CLASS) 2T08 RF PN 20 (150 CLASS) 2T08

10TO 12 10TO 12

PN 20 (150 CLASS)

PN 20 (150 CLASS)

RF RF

BAB42G BAB43G

9 9

ASTM A352-lCC I Full Port

Double Block & Bleed (Featured Ball Valve) API 60; CSA Z245.15

2TOB

10TO 12

PN 20 (150 CLASS) PN 20 (150 CLASS)

RF RF

ASTM A350.LF2 CI.1I 3-Píece Design

ASTM A350-LF2 C1.1/3-PÎece Design

DAB41

9 9

DAB41G

Incorporating Colt Engineerin9

SharePointlPrime Operaling ManualSI"ncard SpecifcatiansUBU-TLM.SPEC.EM.(3 Specification - Piping Maleoal

E~~%')Nomi(s

Worley

Parsons

TALISMAN

ENE R G Y

resources & energy

GSA PI PI NG MATERIAL SPECI FICATION

ZBC2

Rev. A

Page

Feb. 10, 2009 1 012

f~RRÊSSUREmiMITS~1¥l~~f~~li~~~ îêsAl1662~Ø7&~t~'iL' ¥mBOVÊtGROtJNÔ~LÖW~EMêERATURE~1SWË.8T~H'íÔRÖgflRBONs%(ilt¡~!,~tii~~

SWEET HYDROCA.RBONS, FUEL GAS, PROCESS DRAIN At'D VENT, PROPANE REFRIGERANT, METHANOL, NATURAL GAS (CSA Z662-07 CATEGORY II SERVICES)

CSA CLASS

4,960 kPag 4,600 kPag

@ @

.45/38°C 120°C

PN 50

1

Corrosion Allowance: 0.0625" (1.6 mm) Radioqraphy: 15%

liTEM Pipe

ASME 836.10

Class Location Designation: Class 1 Desion Factors: F=0.8, L=0.625. i=1.00, J=1.00

RATING

(ASME 300) PWHT: Notes 1

Branch Table:

SIZE. NPS

0.5 TO 0.75

JOINT

MATERIAL

NOTES

2

2

160

XS

1 TO 1.5

CSAZ245.1 Flange ASME B16.5

2TO 12

STD

300 CLASS 300 CLASS 300 CLASS

PE PE 8W

RFWN

ASTM A333 Gr 6, SMLS ASTM A333 Gr 6, SMLS

CSA Z245.1 Gr 241, Cat II, -45 C

2TO 12 2TO 12

RFBLlND

ASTM A350-LF2 Class 1 ASTM A350-LF2 Class 1

ASTM A350-LF2 Class 1, THRD Bore 0.5

3

Reducing Flanges

ASME B165

2T02 2T02 2T02

2TO 12

0.5 TO 1.5

RFBLlND

RFBLlND

300 CLASS 300 CLASS

300 CLASS

RFHUB

RFWN

ASTM A350-LF2 Class 1, THRD Bore 0.75" ASTM A350-LF2 Class 1, THRD Bore 1.00"

ASTM A350-LF2 Class 1,2 - 1." THRD Taps

3

Orifice Flanges

ASME 816.36

Fittings

ASME B16.11 ASME B16.9

3000#

SAlvtE AS PIPE

THRD

2TO 12

0.5 TO 1.5

8W

THRD

ASTM A350-LF2 Class 1 ASTM A42o.WPL6

ASTM A350-LF2 Class 1

ASTM A333.6, SMLS, 100mm LG

ASTM A333-6, SMLS, 100mm LG

3

Union MSS,SP-83 Nipple

ASME 836.10

3000#

SCH 160

XS

05TOO,75

1 TO 1.5

THRD

THRD

THRD

THRD

Swage

MSS SP-95

0.5 TO 0.75 1 TO 1,5

SCH 160

XS

ASTM A42o-WPL6

ASTM A420-WPL6

Olet

MSS SP-97

0.5 TO 1.5

3000#

SAME

THRD

BW

2T04

Plug

ASME 81611

AS PIPE

ASTM A350-LF2 Class 1 ASTM A350-LF2 Class 1

ASTM A.350-LF2 Class 1, Solid Round Head

4

4

0.5 TO 1.5

MNPT

Line Blank

ASME B16.48

2TO 12

ALL

300 CLASS

RF Fig. 8

ASTM A516-70N

ASTM A 193-B7M, Stud Bolt

13,14

Bolt ASME B16,5 Nut ASME B16.5

ALL

ASTM A194-2HM

300

Gasket

ASME 81620

2TO 12

CLASS

RF

3mm THK, 316 SS Graphoil filled, CS Outer ring,

Incorporating Colt Engineering

SharePolotlPrrme Operating IAanuallSlarKa,d SpeciC8tiOnsileU-TLM.SPEC-EM-003 Specification - Piping Matenal

~:"'.il'ff¡ N . " .:;r.,"4~$"~A,-' ø. '.' omics

WorleyParsons

resources & energy

TALISMAN i-:a5Si!~::

ENE R G Y

CSA PIPING MATERIAL SPECIFICATION

Rev.

ZBC2

A

Feb. 1 D, 20D9

Page 2 of 2

~ÄBbVaGROUND~LOWATEM~ÊRATU~E~SWEEnHYDRøGARBÖN~(U

SWEET HYDROCARBONS, FUEL GAS, PROCESS DRAIN AND VENT, PROPANE REFRIGERANT, METHANOL, NATURAL GAS

'rRRESSUREiIlMIJ,S~1t~I~lgS~~~;¡1f tfêSiMZ.662tOI~ì,l(i~1;

CSA CLASS

4,96D kPag

(CSA Z662-07 CATEGORY ii SERVICES)

4,600 kPag

Class Location Designation: Class 1

@ @

-45/38°C 120°C

PN 50

1 t:: i"

Corrosion Allowance: 0.0625" (1.6 mm) Radioqraphv: 15%

(ASME 30m PWHT: Notes 1

Branch Table:

DesiQn Factors: F=D.8, L=0.625, T=1.00, J=1.00

VALVES (ASME 816.5, 816.10, 816.11, 816.25, 816.34; eSA Z245.15)

I TYPE

Gale Valve

API

t:

SIZE. NPS

RATING

JOINT

BODY MATERIAL I VALVE TYPE

TAG

NOTES

600, 602; CSA Z245.15

0.50

TO 1.50

API 800

THRD

ASTM A350-LF2 CL1/ Solid Wedge

ASTM A352-LCC / Flexible Wedge

ASTM A352-LCC I Flexible Wedge

GIB30

GBB41

9 9 9

2T08

10TO 12

Globe Valve

API

PN 50 (300 CLASS) PN 50 (300 CLASS)

RF RF

GBB41G

602; CSA Z245.15 0.50 TO 1.50

API 800

THRD

ASTM A35Q.LF2 CI.11 Swivel Disc

L1B30

9

9

2T04

Check Valve API 594, 602; CSA Z245.15 0.50 TO 1.50 0.50 TO 1.50

PN 50 (300 CLASS)

RF

ASTM A352-LCC I Swivel Disc

LBB40

API 800 API 800

THRD

THRD

ASTM A350-LF2 CI.1/ Ball Type

ASTM A350-LF2 C1.1! Horizontal Lift Type ASTM A352-LCC / Swing Type

CIB30

CIB31

2TO 12 2TO 12

Ball Valve

API 608; CSA Z245.15

0.50

PN 50 (300 CLASS)

PN 50 (300 CLASS)

RF

RF

CBB42 CBB43

ASTM A352.LCC / Wafer Type

6,9 6,9 7,9 7.8.9

TO 1.50

PN 250 (1500 CLASS)

PN 50 (300 CLASS) PN 50 (300 CLASS) PN 50 (300 CLASS)

THRD

ASTM tI.350-LF2 CL1/ Regular Port

ASTM A352-LCC / Regular Port

BEB30

BBB40

BBB41

9 9

2T06 2T06

8 TO 12 8 TO 12

RF RF

ASTM A352-LCC I Fu!1 Port

.ASTM A352-LCC / Regular Port .A.STM A352-LCC / Full Port

PN 50 (300 CLASS)

PN 50 (300 CLASS) PN 50 (300 CLASS) PN 50 (300 CLASS)

RF RF

RF RF RF

RF

BBB40G

9 9

9 9

9

BBB41G

BBB42

Ball Valves for use in Liquid Services ONLY (clw self-relieving seats)

2T06 2T06

8TO 12 8TO 12

API

ASTM A352-LCC I Regular Port

ASTM A352-LCC I Full Port

ASTM A352-LCC I Regular Port

BBB43

BBB42G BBB43G

9 9

PN 50 (30 CLASS)

ASTM A352-LCC / Full Port

Double Block & Bleed (Featured Ball Valve) 60; CSA Z245.15

2T04

6TO 12

PN 50 (300 CLASS) PN 50 (300 CLASS)

RF RF

tI,STM A350.LF2 CL11 3.Piece Design

tI,STM A350-LF2 CI.11 3.Piece Design

DBB41

9 9

DBB41G

Incorporating Colt Engineering

SharePoinllPrime Opeating ManUallSlandar SpecificatíonsIIBU.TlM-SPEC-EM-OD3 SpecificaliDn - Piping Materal

~i~~~J,Nomics

Worley

Parsons

I

TALISMAN

ENE R G Y

aT 1'! 'N

resources & energy

CSA PI P N G MATE RIAL S P EC F I CATI 0 N

I

ZCC2

Rev. A

Feb. 10, 2009

1

Page

of 2

~AaOVEtGRØUNOjillOW&TEMB.ERAtI.R~~S.wEEm;HY()RÖGARßONSX(Jgn~l~~il~lI1¡!j¡0i ~i?RESSURii~mMI'tSff~\1i~~~~JK4t~ gßSA1ZG62röiIJ4~~r;J: CSA CLASS SWEET HYDROCARBONS, FUEL GAS, PROCESS DRAIN AND VENT, PROPANE

REFRIGERANT. METHANOL, NATURAL GAS (CSA 2662,07 CATEGORY II SERVICES)

9,930 kPag 9,200 kPag

@ @

-45/38°C 120 °C

P N 1 00

1

Corrosion Allowance: 0.0625" (1.6 mm) Raáioaraphv: 15%

Class Location Designation: Class 1 Desion Factors: F=O.8, L=0.625, T=1.00, J=1.00

RATING

(ASME 600) PWHT: Notes 1

Branch Table:

liTEM

Pipe

ASMEB36.1O CSAZ245.1

SIZE. NPS

0.5 TO 1.5

2

JOINT

PE

BW

BW

MATERIAL

NOTES

2 2 2

SCH 160

XS

2-1/2 to 3 4 TO 10

12

STD STD

XS

BW BW

ASTM A333 Gr 6, SMLS ASTM A333 Gr 6, SMLS ASTM A333 Gr 6, SMLS CSA Z245, 1 Gr 359, Cat Ii, -45 C CSA 2245.1 Gr 359, Cat II, -45 C

Flange ASMEB16.5

CSA 2245.12 ASME B16.5

Reducing Flanges

2T03

4 TO 12

PN 100 PN 100

600 CLASS 600 CLASS 600 CLASS 600 CLASS

600 CLASS

2TO 12

RFWN RFWN RFBLlND

ASTM A350.LF2 Class 1

CSA Z245.12 Gr 359, Cal II, -45C

3 3

ASTM A350.LF2 Class 1

ASTM A350.LF2 Class 1, THRD Bore 0.5 ASTM A350-LF2 Class 1, THRD Bore 0.75'

ASTM A350,LF2 Class 1, THRD Bore 1.00'

ASME B16.5

2T02

2iO2 2ï02

Orifice Flanges

ASME B16.36

RFBLlND RFBLlND RFHUB

RFWN RFWN

2T03

4 TO 12

ASTM A350-LF2 Class 1

CSA 2245.12 Gr 359, Cat II, -45C

3

PN 100

3

Fittngs

ASME B16,11 ASME 816.9

0.5 TO 1.5

3000#

S¡1.ME AS PIPE

SAME AS PIPE

THRD

BW BW

2T03

4 TO 12

CSAZ245.11 Union MSS-SP-83 Nipple ASME B36.10

.ASTM A350-LF2 Class 1 ASTM A420-WPL6 CSA 2245,11 Gr 359, Cat II, -45C

3

3

0.5 TO 1.5

3000 #

SCH 160 SCH 160

3000 #

SAME

THRD

ASTM A350-LF2 Class 1

ASTM A333-6, SMLS, 100mm LG

0.5 TO 1.5

THRD

THRD

Swage MSSSP-95 Diet

MSS SP-97

05T01.5

05 TO 1.5

ASTM A420.WPL6

THRD

BW

2T03

Plug

ASME B16.11

AS PIPE

ASTM A350.LF2 Class 1 ASTM A350.LF2 Class 1

ASTM A350.LF2 Class 1, Solid Round Head

4 4

0.5 TO 1.5

MNPT

Line Blank ASME B16.48 Bolt

ASME B16.5 Nut ASME 816.5

2TO 12

ALL

600 CLASS

RF Fig, 8

ASTM A516-70N

ASTM A 193.87M. Stud Bolt

ASTM A 194-2HM

13,14

ALL

Gasket

ASME B16.20

2TO 12

600 CLASS

RF

3mm THK, 316 S8 Graphoil filled, CS Outer ring

Incorporating Colt Engineeiing

;i;¡""""'N m'i s'" t,"'oA'i 0 (

SharePoinl\Prime Operating Manual\Slanord Spedfications\l8U.iLr.A~SPEC~EM-003 Spefication - Piping Material

Worley

Parsons

TALISMAN

ENE R G Y

1;' uø 1: W!l

resources & energy

CSA PIPI NG MATERIAL SPECI FICATION

SWEET HYDROCARBONS, FUEL GAS, PROCESS DRAIN f'.ND VENT, PROPANE REFRIGERANT, METHANOL, NATURAL GAS (CSA Z662,07 CATEGORY ii SERVICES)

ICC2

Rev. A

Feb. 10, 2009

2 of 2

Page

~¡P.RESSUREjrrMits~~I\~~l~¡¡~ i~csÄi'Z66il()1,~~~~,JJf ¡~ÂBø\iÊtGROÛN()3LÙWiifE.MFiERÄtiJREttSWËEt¡J\lDROßÄRBdN~(l1T)i~~ltf4~~~1!~~~ CSA CLASS

9,930 kPag 9,200 kPag

@ @

,45/38°C 120°C

PN 1 00

1 ¡:

Corrosion Allowance: 0.0625" (1,6 mm) RadioaraDhv: 15%

Class Location Designation: Class 1 Desian Factors: F=0.8, L=0.625, T=1.00, J=1.00

(ASME 600) PWHT: Notes 1

Branch Table:

VALVES (ASME 816.5, 816.10, 816.11, 816.25,816.34, eSA Z245.15)

;-;.

I TYPE SIZE - NPS RATING JOINT BODY MATERIAL I VALVE TYPE

Gate Valve

API 600, 602; CSA 245.15

0.50

TO 1.50

API

800

THRD

RF

ASTM A350-LF2 CL1 , Solid Wedge

2T06

8 TO 12

Globe Valve

API

PN 1 DO (600 CLASS) PN 100 (600 CLASS)

ASTM A352.LCC , Flexible Wedge

ASTM A352-LCC ¡ Flexible Wedge

RF

602; CSA 245.15

0.50

TO 1.50

API BOO

THRD

2T04

Check Valve

API

PN 100 (600 CLASS)

RF

ASTM A350.LF2 CL1 , Swivel Disc ASTM A352-LCC , Swivel Disc

594, 602; CSA245.í5 0,50 TO 1.50 0.50 TO 1.50

2iO 12 2iO 12

API

800

THRD THRD

ASTM A350-LF2 el.1 , Ball Type

ASTM A350-LF2 CL1 I Horizontal Lift Type

ASTM A352-LCC ¡ Swing Type

API BOO

PN 100 (600 CLASS) PN 100 (600 CLASS)

RF RF

ASTM A352-LCC' Wafer Type

Ball Valve

API 608: CSA 245.15

0.50 TO 1.50 PN 250 (1500 CLASS) THRD

2 TO 6 PN 100 (600 CLASS) RF

ASTM A350-LF2 CL11 Regular Port

ASTM A352,LCC / Regular Port

2 TO 6 PN í 00 (600 CLASS) RF a TO 12 PN 100 (600 CLASS) RF 8 TO 12 PN 100 (600 CLASS) RF

Ball Valves for use in Liquid Services ONLY (c/w self-relieving seats)

ASTM A352.LCC' Full Port

ASTM A352.LCC , Regular Port

ASTM A352-LCC / Full Port

2 TO 6 PN 100 (600 CLASS) RF 2 TO 6 PN 100 (600 CLASS) RF

A8TM A352.LCC , Regular Port ASTM A352-LCC / Full Port

ASTM A352-LCC / Regular Port

8 TO 12 PN 100 (600 CLASS) RF 8 TO 12 PN 100 (600 CLASS) RF

Double Block & Bleed (Featured Ball Valve)

ASTM A352.LCC , Full Port

API6D; CSA 245.15

2T06

8 TO 12

PN 100 (600 CLASS)

RF RF

ASTM A350-LF2 CL1 / 3.Piece Design

PN 100 (600 CLASS)

ASTM A350.LF2 CL1/3-Piece Design

Incorporating Coil Engineering

f~¡t~:iNomics

SharePointlPrime Operating ManuallStandard SpedficationsIIBU.TLM-SPEC.EM.003 Speafication - Piping Mate"al

Worley

Parsons

TALISMAN ,trt!;:

ENE R G Y

resources & energy

CSA PIPING MATERIAL SPECI FICATION

ZDC2

Rev. A

Feb. 10, 2009

1 of 3

Page

~AaøVE~GROJjND)¡EÖWi.EMRERÄTUR~;SWEEriHY))Röt;ÄRBØNSJ(~ßRESSURE~fiIMirSi~tl'i~¡¥tli'~~~~: ~ØSÄ?;Z66ifim~~~fi~¡;f

SWEET HYDROCARBONS. FUEL GAS, PROCESS DRAIN AND VENT, PROPANE CSA CLASS

REFRIGERANT, METHANOL,

NATURAL GAS

(CSA 2662-07 CATEGORY II SERVICES)

14,890 kPag @ 13.796 kPag @

,45/38°C 120°C

PN 1 50

1

Corrosion Allowance: 0.0625" (1.6 mm) RadioaraDhv: 15%

i ITEM

Class Location Designation: Class 1 Desian Factors: F=0.8, L=0.625, T=1.00, J=1.00

RATING

IASME 9001 PWHT: Notes 1

Branch Table:

SIZE. NPS

0.5 TO 1.5

JOINT

MATERIAL

NOTES

2 2 2 2 3 3

Pipe

ASME B36,10 CSA 2245.1

2T03 410B

10 TO 12

SCH 160 SCH XS SCH XS SCH 80

PE

BW BW

BW

ASTM A333 Gr 6, SMLS ASTM A333 Gr 6, SMLS CSA 2245.1 Gr 359, Cat II, -45C CSA 2245.1 Gr 359, Cat II, -45C

Flange

ASME B16.5

2T03

4 TO 12

CSA2245.12

ASME B16.5

2TO 12

PN 150 PN 150 900 ClJSS

1500 CLASS

1500 CLASS 1500 CLASS

RFWN RFWN

RFBLlND

ASTM A350-LF2 Class 1 CSA 2245.12 Gr 359, Cat II, ,45C ASTM A350-LF2 Class 1

ASTM A350-LF2 Class 1, THRD Bore 0.5 ASTM A350-LF2 Class 1, THRD Bore 0.75" ASTM A350-LF2 Class 1, THRD Bore 1.00"

Reducing Flanges

ASME B16,5

2T02 2T02 2T02 2T03

4 TO 12

RFBLlND RFBLlND RFHUB

RFWN RFWN

Orifice Flanges

ASME 816.36

PN 150 PN 150

ASTM A350,LF2 Class 1

CSA 2245.12 Gr 359, Cal II, -45C

3 3

Fittngs

ASME B16.11 AS ME 816.9

0.5 TO 1.5

3000#

SAME SAME

THRD

AS PIPE

AS PIPE

ASTM A350-LF2 Class 1

ASTM A420,WPL6 CSA 2245.11 Gr 359, Cat Ii, -45C

3

2T03

4 TO 12

BW BW

CSA2245.11 Union

MSS-SP-B3 Nippie ASME B36.10

0.5 TO 1.5

3000 #

THRD

THRD

ASTM A350-LF2 Class 1

ASTM A333-6, SMLS, 100mm LG

ASTM A420-WPL6

0.5 TO 1.5

0,5 TO 1.5

0.5 TO 1.5

SCH 160 SCH 160

3000 #

SAME

Swage

MSS SP-95 Diet MSS SP-97

THRD

THRD BW

MNPT

1500 CLASS

2TO 3

Plug ASMEB16.11 Line Blank ASME B16.48

Bolt

ASME 816.5

ALL

ALL

AS PIPE

ASTM A350.LF2 Class 1 ASTM A350,LF2 Class 1

ASTM A350-LF2 Class 1, Solid Round Head

ASTM A516-70N ASTM A516-70N

ASTM A 193.B7M, Stud Bolt

4 4

0.5 TO 1.5

2T02

3 TO 12

RF Fig, 8

900 ClJSS

RF Fig. 8

13,14 13,14

Nut

ASME 816.5

ASTMA194.2HM

1500 CLASS

900 CLASS

Gasket

ASME B16.20

0.5 TO 2

3TO 12

RF RF

3mm THK, 316 SS Graphoil filed, CS Outer ring, 316SS Inner ring 3mm THK, 316 S8 Graphoil filed, CS Outer ring, 316SS Inner ring

Incorporating Colt Engineering

SharePOinllPrime Operating ManuaJ\Standard Speciftations\lBU-TLM-SPEC-EM-003 Specification - PjpJn~ Material

~:;¡f'¡t~Nom'l(s" "!:-a'''''-,'~.''

WorleyParsons

resources & energy

TALISMAN ..~'7Wij,,

ENE R G Y

CSA PI PIN G MATERIAL SPECI FICATION

SWEET HYDROCARBONS, FUEL GAS, PROCESS DRAIN AND VENT, PROPANE REFRIGERANT, METHANOL, NATURAL GAS (CSA Z662..7 CATEGORY II SERVICES)

ZDC2

Rev. A

Feb. 10, 2009

Page 2 of 3

t!AB0\1EiGROÚNDttIoW,,;rEMeERAtlJRE¡1SWEEtiHYM()bÄR.aONS;t(l!nl~&fl¥~~1~~~~iI~RimSSÜRB¡uiMITS~N~~~i~f~~~ ~bS'ß'Zß6,2;øi~r~J*~~% CSA CLASS

14,890 kPag @ 13,796 kPag @

-45/38°C 120°C

PN 1 50

1

Corrosion Allowance: 0.0625" (1.6 mm) Radioaraohv: 15%

Class Location Designation: Class 1 Desian Factors: F=0.8, L=0.625, T=1.00, J=1,OO

(ASME 900) PWHT: Notes 1

Branch Table:

VALVES (ASME 816.5,816.10,816.11,816.25,816.34, CSA 2245.15)

I TYPE

Gate Valva

API

SIZE, NPS

RATING

JOINT

BODY MATERIAL 1 VALVE TYPE

TAG

NOTES

600, 602; ASME B16.34; CSA Z245.15

0.50 TO 1.50

PN 250 (1500 CLA.SS)

THRD

RF

ASTM A350-LF2 CI.11 Solid Wedge

2T02

PN 250 (1500 CLASS)

PN 150 (900 CLASS) PN 150 (900 CLASS)

ASTM A352-LCC , Flexible Wedge ASTM A352-LCC , Flexible Wedge

ASTM A352.LCC 1 Flexible Wedge

3104

6TO 12

Globe Valve

RF RF

GJB30 GEB40 GDB40 GDB40G

9 9 9

9

,A,PI602; ASME B16.34; CSA Z245. 15 PN 250 (1500 CLASS) 0.50 TO 1.50

THRD

RF

ASTM A350-LF2 CI.11 Swivel Disc

LJB30

LEB40

LDB4u

9 9 9

2T02

3 T04

PN 250 (1500 CLASS)

PN 150 (900 CLASS)

ASTM A352-LCC , Swivel Disc

RF

ASTM A352-LCC , Swivel Disc

Check Valve API 594, 602; ASME B16.34; CSA Z245.15 PN 250 (1500 CLASS) 0.50 TO 1.50

THRD

ASTM A350-LF2 CI.1 / Ball Type

0.50 TO 1.50

PN 250 (1500 CLASS) PN 250 (1500 CLASS) PN 250 (1500 CLASS)

PN 150 (900 CLP.SS)

THRD

ASTM A350.LF2 CI.11 Horizontal Lift Type

2T02 2T02

3TO 12 3TO 12

Ball Valve

RF RF RF

RF

ASTM A352-LCe / Swing Type

ASTM A352-LCC / Wafer Type

ASTM A352-LCC 1 Swing Type

PN 150 (900 CLASS)

ASTM A352-LCC 1 Wafer Type

CJB30 CJB31 CEB42 CEB43 CDB42 CDB43

6,9 6,9 7,9

7,8,9

7,9

7,8,9

API 608; ASME B 16,34; eSA Z245, 15 PN 250 (1500 CLASS) 0.50 TO 1.50

THRD

ASTM A350-LF2 CL.L' Regular Port

ASTM A352-LCC , Regular Port

ASTM A352-LCC 1 Full Port ASTM A352-LCC 1 Regular Port

BEB30

9 9 9 9

2TO 2

PN 250 (1500 CLASS)

RF RF

BEB40

BEB41

2T02

3 T04 3 T04

6TO 12 6TO 12

PN 250 (1500 CLASS)

PN 150 (900 CLASS) PN 150 (900 CLASS)

PN 150 (900 CLASS)

PN 150 (900 CLASS)

PN 250 (1500 CLASS)

RF RF RF

RF

RF

BDB40

BDB41

ASTM A352-LCC , Full Port

ASTM A352-LCC 1 Regular Port ASTM A352-LCC 1 Full Port

9

9

9

BDB40G

BDB41G

Ball Valves for use in Liquid Services ONLY (clw self.relieving scats)

2T02 2T02 3104 3104

6TO 12 6TO 12

Plug Valve API 599: CSA Z245.15

1 TO 1.5

ASTM A352-LCC 1 Regular Port

ASTM A352-LCC 1 Full Port

BEB42

BEB43 BDB42

BDB43

9 9 9

PN 250 (1500 CLASS)

RF RF

PN 150 (900 CLASS) PN 150 (900 CLASS) PN 150 (900 CLASS) PN 150 (900 CLASS)

ASTM A352-LCC , Regular Port

RF RF RF

ASTM A352-LCC 1 Full Port

ASTM A352-LCC 1 Regular Par!

ASTM A352-LCC 1 Full Port

9

9 9

BDB42G BDB43G

1500 CLASS

THRD

ASTM A350-LF2 CL 1 f Regular Pattern

PEB30

9

Incoporating Coit Engineering

SharePa,nllPrime Operating ManuallSlanjard Specif1calions~BU.TLM.SPEC-EM-003 Speclfcation - Piping Material

~;~~:f;iNomi(s

Worley

Parsons

TALISMAN

ENE R G Y

resources & energy

CSA PI PI NG MATE RIAL SP ECIFICATION

ZDC2

Rev. A

Feb. 10, 2009

Page 30f3

~ABO,VEt(;ROUNIJJliilQW;r,EMRERAtüRË~;SWÊETtflÝ;DR()ØARBONS~(ßT)¥£~tY~~$l~~¥g4t ~RRESSOJ~E4úIMliS~~~~ilt¡~~ ffPSÄrZ6ß2tl)1i.l(*~¥f~ CSA CLASS SWEET HYDROCARBONS, FUEL GAS, PROCESS DRAIN AND VENT, PROPANE

REFRIGERANT, METHANOL, NATURAL GAS (CSA Z662-07 CATEGORY ii SERVICES)

14,890 kPag @ 13,796 kPag @

-45/38°C

120 DC

PN 1 50

1

Corrosion Allowance: 0.0625" (1.6 mm) Radiooraphy: 15%

Class Location Designation: Class 1 Desion Factors: F=0.8, L=O.625, T=1.00, J=1.00

JOINT RF RF

BODY MATERIAL! VALVE TYPE

ASTM A352-LCC ¡ Regular Pattern

(ASME 900) PWHT: Notes 1

Branch Table:

TAG

I TYPE SIZE. NPS RATING

2 TO 2 1500 CLASS

3 TO 12 PN 150 (900 CLASS) Double Block & Bleed (Featured Ball Valve)

API6D; API

NOTES

9

PEB40

PDB40G

ASTM A352.LCC ¡ Regular Pattern

9

608; ASME 816.34; CSA Z245.L5

2 TO 2 1500 CLASS

3 TO 4 PN 250 (1500 CLASS) 6 TO 12 PN 250 (1500 CLASS)

RF

ASTM A350-LF2 CL.L ¡ 3.Piece Design

DEB41

DDB41

9

9 9

RF RF

ASTM A350.LF2 CI.1 ¡ 3.Pieee Design

ASTM A350.LF2 CI. 1 ¡ 3.Pieee Deign

DDB43G

Incorporating Colt Engineering

SharePoint\Prime Operating Manual\Standard Spacifications\JBUøTlM-5PEC-EM-0Q SpeCification - Piping Material

""" "N ."

~,c,"~~,;t!; omics t04.,,,.~,.-e

i~

WorleyParsons

resources & energy

TALISMAN 'I.l!fS"~.

ENE R G Y

CSA PIPI NG MATERIAL SPECI FICATION

SWEET HYDROCARBONS, FUEL GAS, PROCESS DRAIN AND VENT, PROPANE REFRIGERANT, METHANOL, NATURAL GAS (CSA Z662-07 CATEGORY II SERVICES)

ZEC2

Rev. A

Feb. 10, 2009

1

Page

of 2

~PRESStiREH:;MITS~'r¡t)!~ffàl7¥~; fCSÆz6li2jô1i§$~t~ ~l\BÔYÐlGRÖÜNörlloWj,tEMaERAiuREWSWEETiÃY()ROGARBøNS¡(lmi~;,¡;i~!i~l\~!(ff~\~ eSA CLASS

24,820 kPag @ 22,996 kPag @

-45/38°C 120°C

PN 250

; ;. ¡.;~ "

Corrosion Allowance: 0.0625" (1.6 mm) Radioaraohy: 15%

Class Location Designation: Class 1 Desian Factors: F=0.8, L=0.625, T=1.00, J=1.00

RATING

XXS

(ASME 1500) PWHT: Notes 1 Branch Table: 1

NOTES

liTEM Pipe

ASME B36,10

SIZE -NPS

JOINT

PE

MATERIAL

if

l..

0.5 TO 1,5

2T03

CSAZ245.1

Flang(J ASME B16.5 CSA Z245.12 AS ME B16.5

160

8W

BW

4 TO 12

SCH 120

ASTM A333 Gr 6, SMLS ASTM A333 Gr 6, SMLS CSA Z245.1 Gr 359, Cat II, -45C

2

2

i L.

2T03

4 TO 12

PN 250 PN 250

1500 CLASS 1500 CLASS 1500 CLASS 1500 CLASS

RFWN

ASTM A350-LF2 Class 1

CSA Z245.12 Gr 359, Cat II, -45C

3

3

2TO 12

RFWN RFBLlND

RFBLlND RFBLlND

1~ ~-: ¡;.:

ASTM A350-LF2 Class 1

ASTM A350-LF2 Class 1, THRD Bore 0.5 ASTM A350-LF2 Class 1, THRD Bore 0.75" .ASTM A350.LF2 Class 1, THRD Bore 1.00'

t

¡ !

Reducing Flanges

ASME B16.5

2T02 2T02 2T02

2TO 3

4 TO 12

RFHUB

RFWN RFWN

Orifice Flanges ASME B16.36

PN250

PN 250

ASTM A350,LF2 Class 1

CSA Z245.1 Gr 359, Cat II, -45C

3 3

Filtings

ASME 816.11 ASME 816.9 CSAZ245,11 Nipple ASME 836.10

0.5 TO 1.5

600#

SAME SAME

THRD

AS PIPE

2T03

4 TO 12

BW BW

AS PIPE

ASTM A350-LF2 Class 1 ASTM A420-WPL6 CSA Z245.11 Gr. 359, Cat II, -45C

ASTM A333-6, SMLS, 100mm LG ASTM A420-WPL6

3

3

0.5 TO 1.5

0.5 TO 1.5

XXS XXS

THRD

Swage

MSS SP-95

THRD

THRD

AS PIPE

BW

Diet

MSSSP-97

Plug

ASME B16.11

0.5 TO 1.5

6000#

SAME

2T03

0.5 TO 1.5

ASTM A350-LF2 Class 1 ASTM A350-LF2 Class 1

ASTM A350-LF2 Class 1, Solid Round Head

4 4

MNPT

1500 CLASS

1500 CLASS

Line Blank ASME B16.48

Bolt ASME B16.5

2T08

10TO 12

ALL ALL

RF Fig. 8

RF B&S

ASTM A516-70N ASTM A516. 70N

ASTM A193-BïM, Stud Bolt

ASTM A 194.2HM

13,14 13,14

Nut

ASME B16.5

Gasket

ASME B16.20

05 TO 12

1500 CLASS

RF

3mm THK, 316 5S Graphoil filled, CS Outer ring, 316SS Inner ring

Incorporating Colt Engineering

ShorePoint\Prime Operating Manual\Standard Speclfcations\IBU-TLM-SPEC-EM-003 Specification - Piping Material

~;d"';t;¡, Nom'i (S'" :f",!:.:1;i?fI../

WorleyParsons

resources & energy

TALISMAN

ENE R G Y

Z Ee2

Rev. A

"'"S'l

CSA PI PI N G MATE RIA L S P EC I F I CATI 0 N

Feb. 10, 2009

Page 2 of 2

;il'AI1ÔVE!G'RQl.NO¡~JloW;j¡EMRErmtÚRij'SWËEirillvóRÖcARBÖNSl(i:n:~~~~li~X~?~l1i~ ~'.I?RE5s.ÚRaiIMlt5~tti0t~l¡t%W:~ ~.u.SA.j.i6621(ll*Itik~¡t CSA CLASS SWEET HYDROC.ARBONS, FUEL GAS, PROCESS DRAIN AND VENT, PROPANE

REFRIGERANT, METHANOL, NATURAL GAS (CSA Z662-07 CATEGORY ii SERVICES)

24,820 kPag @ 22,996 kPag @

-45/38°C 120°C

PN 250

1

Corrosion Allowance: 0.0625" (1.6 mm) Radiooraphy: 15%

Class Location Designation: Class 1 Desian Factors: F=0.8, L=0.625, T=1.00, J=1.00

(ASME 1500) PWHT: Notes 1

Branch Table:

VALVES (ASME 816.5,816.10,816.11,816.25,816.34, CSA Z245.15)

I TYPE SIZE - NPS RATING JOINT BODY MATERIAL I VALVE TYPE

Gate Valve

API

TAG

NOTES

600, 602; ASME B16.34; CSA Z245, 15 0.50 TO 1.50 API 1500

THRD

2 TO 3 PN 250 (1500 CLASS) 4 TO 12 PN 250 (1500 CLASS)

Globe API

RF RF

ASTM A350-LF2 CLl I Solid Wedge ASTM A352.LCC I Flexible Wedge ASTM A352-LCC I Flexible Wedge

GJB30

GEB40 GEB40G

9

9 9

Valve

602; ASME B16.34; CSA Z245,15

050 TO 1.50 API 1500 2 TO 3 PN 250 (1500 CLASS) 4 TO 4 PN 250 (1500 CLASS)

Check Valve

API

THRD

RF

RF

ASTM A350-LF2 CLl I Swivel Disc ASTM A352.LCe I Swivel Disc

LJB30

LEB40

9

9

9

ASTM A352-LCe I Swivel Disc

LEB40G

594, 602; ASME B16.34; CSA Z245.15 0.50 TO 1.50 API 1500 0.50 TO 1.50 API 1500 2 TO 12 PN 250 (1500 CLASS) 2 TO 12 PN 250 (1500 CLASS) Ball Valve

608; ASME B16.34; CSA Z245.15

THRD

THRD

RF

RF

ASTM A350-LF2 eLl I Ball Type ASTM A350-LF2 CLl I Horizontal Uft Type ASTM A352-LeC I Swing Type

ASTM A352-LCC I Wafer Type

CJB30

CJB31

CEB42 CEB43

6,9 6,9 7,9

7,8,9

API

0.50 TO 1.50 PN 250 (1500 CLASS) THRD

2 TO 3 2 TO 3 4 TO 12 4 TO 12

2 TO 3 2 TO 3 4 TO 12 4 TO 12

Plug Valve

.ASTM A350-LF2 CLl i Regular Port

ASTM A352-LCC I Regular Port

BEB30 BEB40

BEB41

9 9

9 9

PN PN PN PN

PN PN PN PN

250 250 250 250

250 250 250 250

(1500 (1500 (1500 (1500

(1500 (1500 (1500 (1500

CLASS) CLASS) CLASS) CLASS)

CLASS) CLASS) CLASS) CLASS)

RF RF RF RF

RF RF RF RF

ASTM A352-LeC I Full Port

ASTM A352-LCC I Regular Port

BEB40G BEB41G

BEB42 BEB43

ASTM A352-LCC I Full Port

ASTM A352-LCC I Regular Por

9

9 9 9 9

Ball Valves for use in Liquid Services ONLY (clw self-relieving seais)

ASTM A352-LCC I Full Port

ASTM A35HCC I Regular Port

ASTM A352-LCC I Full Port

BEB42G BEB43G

API 599: CSA Z245.15 1 TO 1.5 PN 250 (1500 CLASS)

THRD

RF RF

ASTM A350-LF2 CLll Regular Pattern

ASTM A352-LCC I Regular Pattern

2 TO 2 PN 250 (1500 CLASS) 3 TO 8 PN 250 (1500 CLASS)

Double Block & Bleed (Featured Ball Valve) API6D; API 608; ASME B16.34; CSA Z245.15

ASTM A352-LCe I Regular Pattern

PEB30 PEB40 PEB40G

9

9 9

2 TO 2 PN 250 (1500 CLASS) 3 TO 4 PN 250 (1500 CLASS) 6 TO 12 PN 250 (1500 CLASS)

RF RF

RF

ASTM A350-LF2 eL 1/3-Pieee Design

ASTM A350-LF2 eLl I 3-Pieee Design ASTM A350-LF2 CLl I 3-Pieee Design

DEB41 DEB41G

9

9

9

DEB43G

Ineùrpcraling Colt Engineering

tt;~"'A,'''N 0 mics ~",,~.,,'l:!.e

SharePointlPrime Operaling ManuallStandard Speciricaions~BU.TLM.SPEC-EM.003 Specification - Pioil1 Malerial

Information

30 pages

Find more like this

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

898245


You might also be interested in

BETA