Read group6.pdf text version

Group 6

TAPPCO LUBRICANTS

BUILDING NO. [22], STREET NO. [39], KHARTOUM II, P.O. BOX: 13368 KHARTOUM - SUDAN TEL.: +249 183579448/9 FAX: +249 183 579447 E-mail: [email protected]

Product Name: Group 6 Products

Health & Safety Sheets

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING

Identification of substance/preparation :

As Above Application: Non-additive containing lubricant for circulatory systems, and processing applications. For specific application advice see appropriate Technical Data Sheet.

Company Identification :

As Above.

Emergency Telephone Number :

As Above.

2. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Composition :

Highly refined mineral oil (IP 346 DMSO extract < 3%).

Hazardous Components :

No component is present at sufficient concentration to require a hazardous classification.

3. HAZARDS IDENTIFICATION This material is not considered to be hazardous, but should be handled in accordance with good industrial hygiene and safety practices.

4. FIRST-AID MEASURES

Eyes :

Wash eye thoroughly with copious quantities of water, ensuring eyelids are held open. Obtain medical advice if any pain or redness develops or persists.

Skin :

Wash skin thoroughly with soap and water as soon as reasonably practicable. Remove heavily contaminated clothing and wash underlying skin.

Ingestion :

If contamination of the mouth occurs, wash out thoroughly with water. Except as a deliberate act, the ingestion of large amounts of product is unlikely. If it should occur, do not induce vomiting; obtain medical advice.

Inhalation :

If inhalation of mists, fumes or vapour causes irritation to the nose or throat, or coughing, remove to fresh air. If symptoms persist obtain medical advice.

Medical Advice :

Treatment should in general be symptomatic and directed to relieving any effects.

5. FIRE-FIGHTING MEASURES Use foam, dry powder or water fog. DO NOT USE water jets. Fires in confined spaces should be dealt with by trained personnel wearing approved breathing apparatus. Water may be used to cool nearby heat exposed areas/objects/packages. Avoid spraying directly into storage containers because of the danger of boil-over.

Combustion Products :

Toxic fumes may be evolved on burning or exposure to heat. See Stability and Reactivity, Section 10 of this Safety Data Sheet.

6. ACCIDENTAL RELEASE MEASURES Contain and recover spilled material using sand or other suitable inert absorbent material. It is advised that stocks of suitable absorbent material should be held in quantities sufficient to deal with any spillage which may be reasonably anticipated. Spilled material may make surfaces slippery. Protect drains from potential spills to minimise contamination. Do not wash product into drainage system. In the case of large spills contact the appropriate authorities. If spillage occurs call above telephone number. In the case of spillage on water, prevent the spread of product by the use of suitable barrier equipment. Recover product from the surface. Protect environmentally sensitive areas and water supplies.

7. HANDLING AND STORAGE

Handling Precautions :

Avoid contact with eyes. If splashing is likely to occur wear a full face visor or chemical goggles as appropriate. Avoid frequent or prolonged skin contact with fresh or used product. Good working practices, high standards of personal hygiene and plant cleanliness must be maintained at all times. Wash hands thoroughly after contact. Use disposable cloths and discard when soiled. Do not put soiled cloths into pockets.

Fire Prevention :

Product contaminated rags, paper or material used to absorb spillages, represent a fire hazard, and should not be allowed to accumulate. Dispose of safely immediately after use.

Storage Conditions :

Store under cover away from heat and sources of ignition.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure Limits :

There is no appropriate occupational exposure limit for this material. Ensure good ventilation. Avoid, as far as reasonably practicable, inhalation of vapour, mists or fumes generated during use. If vapour, mists or fumes are generated, their concentration in the workplace air should be controlled to the lowest reasonably practicable level.

Protective Clothing :

Wear faces visor or goggles in circumstances where eye contact can accidentally occur. If skin contact is likely, wear impervious protective clothing and/or gloves. Protective clothing should be regularly dry cleaned. Change heavily contaminated clothing as soon as reasonably practicable; dry clean, launder and preferably starch before re-use. Wash any contaminated underlying skin with soap and water.

Respiratory Protection :

Respiratory protection is unnecessary, provided the concentration of vapour, mists or fumes is adequately controlled. The use of respiratory equipment must be strictly in accordance with the manufacturers' instructions and any statutory requirements governing its selection and use.

9. PHYSICAL AND CHEMICAL PROPERTIES Typical Values Grade: Test Method: Physical state Colour Odour Density @ 15°C Kinematic viscosity @ 40°C Kinematic viscosity @ 100°C Flash point (COC) Pour point Units: liquid amber mild 888 100.03 11.40 228 -12

ASTM ASTM ASTM ASTM

D D D D

1298 445 445 92

kg/m³ mm²/s mm²/s °C °C

10. STABILITY AND REACTIVITY Products of this type are stable and unlikely to react in a hazardous manner under normal conditions of use. Hazardous polymerisation reactions will not occur. This material is combustible.

Materials to Avoid :

Avoid contact with strong oxidizing agents.

Hazardous Decomposition Products :

Thermal decomposition products will vary with conditions. Incomplete combustion will generate smoke, carbon dioxide and hazardous gases, including carbon monoxide.

11. TOXICOLOGICAL INFORMATION

Eyes : Skin :

Unlikely to cause more than transient stinging or redness if accidental eye contact occurs. Unlikely to cause harm to the skin on brief or occasional contact but prolonged or repeated exposure may lead to dermatitis.

Ingestion :

Unlikely to cause harm if accidentally swallowed in small doses, though larger quantities may cause nausea and diarrhoea.

Inhalation :

At normal ambient temperatures this product will be unlikely to present an inhalation hazard because of its low volatility. May cause irritation to eyes, nose and throat due to exposure to vapour, mists or fumes. May be harmful by inhalation if exposure to vapour, mists or fumes resulting from thermal decomposition products occurs.

12. ECOLOGICAL INFORMATION

Mobility :

Spillages may penetrate the soil causing ground water contamination.

Persistence and degradability : Bioaccumulative potential : Aquatic toxicity :

This product is inherently biodegradable. There is no evidence to suggest bioaccumulation will occur. Spills may form a film on water surfaces causing physical damage to organisms. Oxygen transfer could also be impaired.

13. DISPOSAL CONSIDERATIONS Where possible, arrange for product to be recycled. Dispose of via an authorised person/ licensed waste disposal contractor in accordance with local regulations. Incineration may be carried out under controlled conditions provided that local regulations for emissions are met.

14. TRANSPORT INFORMATION Not classified as hazardous for transport (ADR, RID, UN , IMO, IATA/ICAO). 15. REGULATORY INFORMATION Not classified as hazardous for supply. No Statutory label required. 16. OTHER INFORMATION

Compiled by:

Technical Department This data sheet and the health, safety and environmental information it contains is considered to be accurate as of the date specified below. We have reviewed any information contained herein which we received from sources outside our organisation. However, no warranty or representation, express or implied is made as to the accuracy or completeness of the data and information contained in this data sheet. Health and safety precautions and environmental advice noted in this data sheet may not be accurate for all individuals and/or situations. It is the user's obligation to evaluate and use this product safely and to comply with all applicable laws and regulations. No statement made in this data sheet shall be construed as a permission, recommendation or authorization given or implied to practise any patented invention without a valid licence. Our organisation shall not be responsible for any damage or injury resulting from abnormal use of the material, from any failure to adhere to recommendations, or from any hazards inherent in the nature of the material.

Issue No: HSE8 December 2007

Issued by: TAPPCO ­ Technical Department Approved by: EXOL, U.K. ­ Technical Department

Group 6A

TAPPCO LUBRICANTS

BUILDING NO. [22], STREET NO. [39], KHARTOUM II, P.O. BOX: 13368 KHARTOUM - SUDAN TEL.: +249 183579448/9 FAX: +249 183 579447 E-mail: [email protected]

Product Name: Group 6A Products

Health & Safety Sheets

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING

Identification of substance/preparation :

As Above.

Application :

Low viscosity mould release fluid. For specific application advice see appropriate Technical Data Sheet.

Company Identification :

As Above.

Emergency Telephone Number :

As Above.

2. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Composition :

Complex distillate consisting of hydrocarbons mainly in the C9-C16 range Proprietary performance additives.

Hazardous Components :

Substance Name: C9-C16 hydrocarbon %w/w 90-95 Health Class Xn (Harmful) Risk R10: Flammable R65: Harmful R38: Irritating to the skin R52/53: Harmful to aquatic organisms See also Section 15 for further regulatory information.

3. HAZARDS IDENTIFICATION This material is classified as flammable and is considered to be harmful due to the aspiration hazard. Prolonged and repeated skin contact can lead to irritation and dermatitis. It is also classified as harmful to the environment.

4. FIRST-AID MEASURES

Eyes : Skin :

Wash eye thoroughly with copious quantities of water, ensuring eyelids are held open. Obtain medical advice if any pain or redness develops or persists. Wash skin thoroughly with soap and water as soon as reasonably practicable. Remove heavily contaminated clothing and wash underlying skin. Launder clothing before re-use. Get medical advice if irritation develops and persists.

Ingestion :

If contamination of the mouth occurs, wash out thoroughly with water. Except as a deliberate act, the ingestion of large amounts of product is unlikely. If it should occur, do not induce vomiting; obtain medical advice. Inhalation: If inhalation of mists, fumes or vapour causes irritation to the nose or throat, or coughing, remove to fresh air. If symptoms persist obtain medical advice.

Medical Advice :

Treatment should in general be symptomatic and directed to relieving any effects.

5. FIRE-FIGHTING MEASURES Note: Classified as flammable. Flash point 38ºC min (PBO 43 Min). Use foam, dry powder or water fog. DO NOT USE water jets. Fires in confined spaces should be dealt with by trained personnel wearing approved breathing apparatus. Water may be used to cool nearby heat exposed areas/objects/packages. Avoid spraying directly into storage containers because of the danger of boil-over.

Combustion Products :

Toxic fumes may be evolved on burning or exposure to heat. See Stability and Reactivity, Section 10 of this Safety Data Sheet.

6. ACCIDENTAL RELEASE MEASURES Treat any spillage as a fire hazard. Spray, vapour or mist can be a potential fire or explosion hazard Contain and recover spilled material using sand or other suitable inert absorbent material. It is advised that stocks of suitable absorbent material should be held in quantities sufficient to deal with any spillage which may be reasonably anticipated. Spilled material may make surfaces slippery. Protect drains from potential spills to minimise contamination. Do not wash product into drainage system. In the case of large spills contact the appropriate authorities, or call the above telephone number. In the case of spillage on water, prevent the spread of product by the use of suitable barrier equipment. Recover product from the surface. Protect environmentally sensitive areas and water supplies.

7. HANDLING AND STORAGE

Handling Precautions :

Where exposure is likely protective clothing should be worn including impervious gloves and eye protection. Ensure good ventilation. Avoid contact with eyes. If splashing is likely to occur wear a full face visor or chemical goggles as appropriate. Avoid frequent or prolonged skin contact with fresh or used product. Good working practices, high standards of personal hygiene and plant cleanliness must be maintained at all times. Wash hands thoroughly after contact. Use disposable cloths and discard when soiled. Do not put soiled cloths into pockets.

Fire Prevention :

Product contaminated rags, paper or material used to absorb spillages, represent a fire hazard, and should not be allowed to accumulate. Dispose of safely immediately after use.

Storage Conditions :

Store under cover away from heat and sources of ignition. Barrels should be stored on their sides, preferably on racks under cover, out of direct sunlight, in a well ventilated area. Care should be taken to avoid over stacking.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION Where prolonged or repeated exposure is likely, protective clothing should be worn including impervious gloves and eye protection. Ensure good ventilation.

Exposure Limits :

Avoid, as far as reasonably practicable, inhalation of vapour, mists or fumes generated during use. If vapour, mists or fumes are generated, their concentration in the workplace air should be controlled to below the level for oil mist quoted in the current HSE Guidance Note EH40. Long term exposure limit (8 hr TWA reference period) = 5 mg/cubic metre. Short term exposure limit (15 min reference period) = 10 mg/cubic metre.

Protective Clothing :

Wear faces visor or goggles in circumstances where eye contact can accidentally occur. If skin contact is likely, wear impervious protective clothing and/or gloves. Protective clothing should be regularly dry cleaned. Change heavily contaminated clothing as soon as reasonably practicable; dry clean, launder and preferably starch before re-use. Wash any contaminated underlying skin with soap and water.

Respiratory Protection :

Respiratory protection is unnecessary, provided the concentration of vapour, mists or fumes is adequately controlled. The use of respiratory equipment must be strictly in accordance with the manufacturers' instructions and any statutory requirements governing its selection and use.

9. PHYSICAL AND CHEMICAL PROPERTIES Typical Values Grades: Test Method: Physical state Colour Odour Density @ 15°C Boiling Range Flash point (Abel) Units: Liquid Blue ASTM D 1298 kg/m³ °C °C 0.72-0.82 140-300 38 min

10. STABILITY AND REACTIVITY This material is flammable.

Materials to Avoid :

Avoid contact with strong oxidizing agents.

Hazardous Decomposition Products :

Thermal decomposition products will vary with conditions. Incomplete combustion will generate smoke, carbon dioxide and hazardous gases, including carbon monoxide.

11. TOXICOLOGICAL INFORMATION

Eyes : Skin :

Unlikely to cause more than transient stinging or redness if accidental eye contact occurs. Unlikely to cause harm to the skin on brief or occasional contact but prolonged or repeated exposure may lead to defatting of the skin and dermatitis.

Ingestion :

Unlikely to cause harm if accidentally swallowed in small doses, though larger quantities may cause irritation, vomiting, nausea and diarrhoea.

Inhalation :

At normal ambient temperatures, toxicity following a single exposure of this product will be unlikely to present an inhalation hazard. May cause irritation to eyes, nose and throat due to exposure to vapour, mists or fumes. May be harmful by inhalation if exposure to vapour, mists or fumes resulting from thermal decomposition products occurs.

12. ECOLOGICAL INFORMATION

Mobility :

Spillages may penetrate the soil causing ground water contamination.

Persistence and degradability :

Expected to biodegrade slowly.

Bioaccumulative potential : Aquatic toxicity :

There is no evidence to suggest bioaccumulation will occur. Slightly toxic to aquatic life, but unlikely to persist for sufficient time to pose a significant hazard. Spills formed on water may affect oxygen transfer and cause physical damage to organisms. 13. DISPOSAL CONSIDERATIONS Dispose of via an authorised person/ licensed waste disposal contractor in accordance with local regulations. Incineration may be carried out under controlled conditions provided that local regulations for emissions are met. Under no circumstances should this material be discharged into the public drainage system, or marine and inland waterways. 14. TRANSPORT INFORMATION Transport classification: Flammable liquid Hazchem code UN UN No. (Substance identification number) UN Packing Group IMO Hazard Class ADR/RID Hazard Class IATA Diamond symbol 3/Y Flammable liquid, Class III 1223 III 3.3 3 Item 31 (c) Flammable liquid Class 3, Packing Group III

15. REGULATORY INFORMATION Symbol Classification R10 R65 R38 R52/53 S2 S23 S24 S43 S61 S62 Black St. Andrews cross on an orange background Flammable, Harmful, Irritant, Dangerous for the environment Flammable Harmful. May cause lung damage if swallowed Irritating to the skin Harmful to aquatic organisms, may cause long term adverse effects in the aquatic environment Keep out of the reach of children Do not breathe vapour Avoid contact with the skin In case of fire, use foam/dry powder/CO2/Halon. Never use water jets Avoid release to the environment. Refer to special instructions / Safety Data Sheet If swallowed, do not induce vomiting. Seek medical advise immediately and show this sheet /label on container.

16. OTHER INFORMATION

Compiled by :

Technical Department This data sheet and the health, safety and environmental information it contains is considered to be accurate as of the date specified below. We have reviewed any information contained herein which we received from sources outside our organisation. However, no warranty or representation, express or implied is made as to the accuracy or completeness of the data and information contained in this data sheet. Health and safety precautions and environmental advice noted in this data sheet may not be accurate for all individuals and/or situations. It is the user's obligation to evaluate and use this product safely and to comply with all applicable laws and regulations. No statement made in this data sheet shall be construed as a permission, recommendation or authorization given or implied to practise any patented invention without a valid licence. Our organisation shall not be responsible for any damage or injury resulting from abnormal use of the material, from any failure to adhere to recommendations, or from any hazards inherent in the nature of the material.

Issue No: HSE9 December 2007

Issued by: TAPPCO ­ Technical Department Approved by: EXOL, U.K. ­ Technical Department

Group 6B

TAPPCO LUBRICANTS

BUILDING NO. [22], STREET NO. [39], KHARTOUM II, P.O. BOX: 13368 KHARTOUM - SUDAN TEL.: +249 183579448/9 FAX: +249 183 579447 E-mail: [email protected]

Product Name: Group 6B Products

Health & Safety Sheets

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING

Identification of substance/preparation :

As Above

Application :

Heat transfer oil. For specific application advice see appropriate Technical Data Sheet.

Company Identification :

As Above. Emergency Telephone Number : As Above.

2. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Composition :

Highly refined mineral oil (IP 346 DMSO extract < 3%) Proprietary performance additives.

Hazardous Components :

No component is present at sufficient concentration to require a hazardous classification.

3. HAZARDS IDENTIFICATION This material is not considered to be hazardous, but should be handled in accordance with good industrial hygiene and safety practices.

4. FIRST-AID MEASURES

Eyes :

Wash eye thoroughly with copious quantities of water, ensuring eyelids are held open. Obtain medical advice if any pain or redness develops or persists.

Skin :

Wash skin thoroughly with soap and water as soon as reasonably practicable. Remove heavily contaminated clothing and wash underlying skin.

Ingestion :

If contamination of the mouth occurs, wash out thoroughly with water. Except as a deliberate act, the ingestion of large amounts of product is unlikely. If it should occur, do not induce vomiting; obtain medical advice.

Inhalation :

If inhalation of mists, fumes or vapour causes irritation to the nose or throat, or coughing, remove to fresh air. If symptoms persist obtain medical advice.

Medical Advice :

Treatment should in general be symptomatic and directed to relieving any effects.

5. FIRE-FIGHTING MEASURES Use foam, dry powder or water fog. DO NOT USE water jets. Fires in confined spaces should be dealt with by trained personnel wearing approved breathing apparatus. Water may be used to cool nearby heat exposed areas/objects/packages. Avoid spraying directly into storage containers because of the danger of boil-over.

Combustion Products :

Toxic fumes may be evolved on burning or exposure to heat. See Stability and Reactivity, Section 10 of this Safety Data Sheet.

6. ACCIDENTAL RELEASE MEASURES Contain and recover spilled material using sand or other suitable inert absorbent material. It is advised that stocks of suitable absorbent material should be held in quantities sufficient to deal with any spillage which may be reasonably anticipated. Spilled material may make surfaces slippery. Protect drains from potential spills to minimise contamination. Do not wash product into drainage system. In the case of large spills contact the appropriate authorities, or call above telephone number. In the case of spillage on water, prevent the spread of product by the use of suitable barrier equipment. Recover product from the surface. Protect environmentally sensitive areas and water supplies.

7. HANDLING AND STORAGE

Handling Precautions :

Avoid contact with eyes. If splashing is likely to occur wear a full face visor or chemical goggles as appropriate. Avoid frequent or prolonged skin contact with fresh or used product. Good working practices, high standards of personal hygiene and plant cleanliness must be maintained at all times. Wash hands thoroughly after contact. Use disposable cloths and discard when soiled. Do not put soiled cloths into pockets.

Fire Prevention :

Product contaminated rags, paper or material used to absorb spillages, represent a fire hazard, and should not be allowed to accumulate. Dispose of safely immediately after use.

Storage Conditions :

Store under cover away from heat and sources of ignition. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure Limits :

There is no appropriate occupational exposure limit for this material. Ensure good ventilation. Avoid, as far as reasonably practicable, inhalation of vapour, mists or fumes generated during use. If vapour, mists or fumes are generated, their concentration in the workplace air should be controlled to the lowest reasonably practicable level.

Protective Clothing :

Wear faces visor or goggles in circumstances where eye contact can accidentally occur. If skin contact is likely, wear impervious protective clothing and/or gloves. Protective clothing should be regularly dry cleaned. Change heavily contaminated clothing as soon as reasonably practicable; dry clean, launder and preferably starch before re-use. Wash any contaminated underlying skin with soap and water.

Respiratory Protection :

Respiratory protection is unnecessary, provided the concentration of vapour, mists or fumes is adequately controlled. The use of respiratory equipment must be strictly in accordance with the manufacturers' instructions and any statutory requirements governing its selection and use.

9. PHYSICAL AND CHEMICAL PROPERTIES Typical Values Grades: Test Method: Physical state Colour Odour Density @ 15°C Kinematic viscosity @ 40°C Kinematic viscosity @ 100°C Flash point (COC) Pour point Units: liquid Pale straw oily 868 20.16 200 -12

ASTM ASTM ASTM ASTM ASTM

D D D D D

1298 445 445 92 97

kg/m³ mm²/s mm²/s °C °C

10. STABILITY AND REACTIVITY Products of this type are stable and unlikely to react in a hazardous manner under normal conditions of use. Hazardous polymerisation reactions will not occur. This material is combustible.

Materials to Avoid :

Avoid contact with strong oxidizing agents.

Hazardous Decomposition Products :

Thermal decomposition products will vary with conditions. Incomplete combustion will generate smoke, carbon dioxide and hazardous gases, including carbon monoxide.

11. TOXICOLOGICAL INFORMATION

Eyes : Skin :

Unlikely to cause more than transient stinging or redness if accidental eye contact occurs. Unlikely to cause harm to the skin on brief or occasional contact but prolonged or repeated exposure may lead to dermatitis.

Ingestion :

Unlikely to cause harm if accidentally swallowed in small doses, though larger quantities may cause nausea and diarrhoea.

Inhalation :

At normal ambient temperatures this product will be unlikely to present an inhalation hazard because of its low volatility. May cause irritation to eyes, nose and throat due to exposure to vapour, mists or fumes. May be harmful by inhalation if exposure to vapour, mists or fumes resulting from thermal decomposition products occurs.

12. ECOLOGICAL INFORMATION

Mobility :

Spillages may penetrate the soil causing ground water contamination.

Persistence and degradability : Bioaccumulative potential : Aquatic toxicity :

This product is inherently biodegradable. There is no evidence to suggest bioaccumulation will occur. Spills may form a film on water surfaces causing physical damage to organisms. Oxygen transfer could also be impaired.

13. DISPOSAL CONSIDERATIONS Where possible, arrange for product to be recycled. Dispose of via an authorised person/ licensed waste disposal contractor in accordance with local regulations. Incineration may be carried out under controlled conditions provided that local regulations for emissions are met.

14. TRANSPORT INFORMATION Not classified as hazardous for transport (ADR, RID, UN , IMO, IATA/ICAO).

15. REGULATORY INFORMATION Not classified as hazardous for supply.

16. OTHER INFORMATION

Compiled by:

Technical Department This data sheet and the health, safety and environmental information it contains is considered to be accurate as of the date specified below. We have reviewed any information contained herein which we received from sources outside our organisation. However, no warranty or representation, express or implied is made as to the accuracy or completeness of the data and information contained in this data sheet. Health and safety precautions and environmental advice noted in this data sheet may not be accurate for all individuals and/or situations. It is the user's obligation to evaluate and use this product safely and to comply with all applicable laws and regulations. No statement made in this data sheet shall be construed as a permission, recommendation or authorization given or implied to practise any patented invention without a valid licence. Our organisation shall not be responsible for any damage or injury resulting from abnormal use of the material, from any failure to adhere to recommendations, or from any hazards inherent in the nature of the material.

Issue No: HSE10 December 2007

Issued by: TAPPCO ­ Technical Department Approved by: EXOL, U.K. ­ Technical Department

Information

19 pages

Find more like this

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

548493


You might also be interested in

BETA
Material Safety Data Sheet (MSDS)
CS31 RED STAIN REMOVER.doc
\\server01\hse\archives\ansiosh