Read XK06-PLXR ENG.03 sd20060525.cdr text version

Platform # 06

Firmware: PLXR

Description:- GM Passlock 1 & 2 & VATS & Saturn Ion Self Learning Functions:- Auto learning unit designed to bypass all GM equipped with Passlock I & Passlock II, VATS & Saturn Ion

Downloadable Firmwares:- PKG7, PLXR, PKG5 Check for firmware and installation manual updates before installing @ www.XpressDownload.com

ION, CANYON, COLORADO, COBALT, PURSUIT

REMOTE

IGNITION

Orange Blue Brown White

White/Black

OR

BCM

White/Blue

White/Yellow

1

Upgrade (Optional)

Ground Out from Remote Start Connect after programming is complete

Programming Interface

. P C.

USB

D2U

OR

2

Brown (-)

Green Blue

Data 2 Data (Optional)

REMOTE

Page 1

Resistor Code Input Resistor Code Output N/C N/C N/C Ignition Input Start Input Connect to 12V Constant Chassis Ground

**Connect Brown wire ONLY after programming is complete**

SYSTEM

IGNITION CYLINDER

STARTER OUTPUT WIRE (+) FROM REMOTE CAR STARTER

D2U

10 PIN HARNESS

This bypass kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle DISCLAIMER : Under no application guide. circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it's distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the by passkit / data bus interface part(s) other than its replacement.

10 PIN HARNESS

Violet/White Violet

Pink/White

Pink Orange Red Black

Programming LED

Programming button

WIRE FUNCTIONS

Brown Green Blue Violet/White Violet Pink/White Pink Orange Red Black

Ground Output When Running (-) (Remote Start Installations Only) Resistor Code Input (Connect to Key Side of Resistor Code Wire) Resistor Code Output(Connect to BCM Side of Resistor Code Wire) N/C N/C N/C Ignition Input (Connect to vehicle ignition wire) Start Input (Connect to (+)Starter Output wire from Remote System) (+)12 Volt Constant Chassis Ground (Do Not Ground To Steering Column)

This connector has dual functions: 1) XKLOADER Firmware Upgrades. 2) 4 Pin Data 2 Data connector to remote system, which replaces wire to wire (w2w) connection on the 10 Pin Harness.

STEP 1- PASSLOCK TYPE SELECTION

ION type Passlock is the default setting. If installing on an ION type Passlock system skip to "Step 2" after connecting the Passlock wires.

*If you are installing on a vehicle equipped with either Passlock 1 or Passlock 2 or VATS you must change Passlock Type before you can program resistor code. (go to Passlock Type Selection on page 2).

STEP 2- PROGRAM RESISTOR CODE

Connect Brown wire to remote starter ONLY AFTER RESISTOR CODE programming is complete. A) Turn Key to START POSITION & HOLD

B) Press & hold Programming Button while key is in the start position. LED will come on for 1 SEC, then turn off. Turn key to OFF position. C) Passlock Resistor Code is now programmed, connect brown wire to ground output from remote starter and test function by remote starting the engine. (For manual transmission vehicles, put shifter in NEUTRAL position and DON'T PRESS CLUTCH when doing STEP B & C)

Reset

1.Unplug 10 pin harness. Press and hold the programming button while re-plugging 10 pin harness to module. 2.Release the programming button, within 2 -3 seconds the LED confirms reset status by rapidly flashing. 3.The module is now reset and has returned to default setting.

INSTALLATION NOTES:

*Saturn ION, GMC Canyon & Chevy Colorado etc do not have starter wires. **This self learning kit will not function on a Passlock 1, Passlock 2 or Vats equipped vehicle until the Passlock Type Selection is changed from the ION Type factory default setting.

SYSTEM

PASSLOCK 1, 2 & VATS CONNECTION

IGNITION KEY

STARTER

REMOTE

IGNITION

BULB TEST (PASSLOCK 1 ONLY)

PASSLOCK 1 & 2

White Black Yellow OR

PASSLOCK 2 ONLY Red / White

Orange/ Black

BCM

Programming Interface

USB

. P C.

1

Upgrade (Optional)

D2U

REMOTE

Brown (-)

Green Blue

10 PIN HARNESS

Ground Out from Remote Start Connect after programming is complete

**Connect Brown wire ONLY after programming is complete**

N/C Resistor Code Output N/C N/C Bulb Test Out ( Passlock1 Only ) Ignition Wire Start Wire (Passlock 1 & 2) Connect to 12V Constant Ground wire in Passlock harness

Violet/White Violet

Pink/White

VATS

Programming LED

Pink Orange Red Black

THESE WIRES WILL BE FOUND IN A ORANGE OR GRAY SLEEVE

Programming button

WIRE FUNCTIONS

Brown Green Blue Violet/White Violet Pink/White Pink Orange Red Black

Ground Output When Running (-) (Remote Start Installations Only) N/C Resistor Code Output N/C N/C Bulb Test Output (Passlock 1 Only) Ignition Wire (Connect to vehicle ignition wire) Start Wire (Connect to (+)Starter Output wire from Remote System) (+)12 Volt Constant Use Passlock Ground In Wire Harness Or Chassis Ground (Do Not Ground To Steering Column)

D2U

10 PIN HARNESS

This connector has dual functions: 1) XKLOADER Firmware Upgrades. 2) 4 Pin Data 2 Data connector to remote system, which replaces wire to wire (w2w) connection on the 10 Pin Harness.

STEP 1- PASSLOCK TYPE SELECTION

Once all Passlock wires have been connected, you must SELECT the proper PASSLOCK TYPE before proceeding to STEP 2 -PROGRAM RESISTOR CODE. Select one of the 3 available PASSLOCK types:

DEFAULT PASSLOCK TYPE is ION

1.To enter PASSLOCK TYPE SELECTION: Turn key to the IGNITION "ON" position, then LED will flash to indictae TYPE. 2.Press programming button 1, 2 or 3 times to select the Passlock Type. LED will flash an equal number of times to confirm selection.

PASSLOCK 1 / VATS = Press Button (1X) one time PASSLOCK 2 = Press Button (2X) two times COLORADO/ION = Press Button (3X) three times

* System is preset for Colorado/Canyon/ION Type

3.To Exit Passlock Selection Type: Press and hold the programming button until LED flashes one time rapidly.

STEP 2- PROGRAM RESISTOR CODE

Connect Brown wire to remote starter ONLY AFTER RESISITOR CODE programming is complete.

A) Start vehicle by key. B) Press & hold Programming Button. LED will come on for 1 SEC, then turn off. Turn key to OFF position. C) Passlock Resistor Code is now programmed, connect brown wire to ground output from remote starter and test function by remote starting the engine. (For manual transmission vehicles, put shifter in NEUTRAL position and DON'T PRESS CLUTCH when doing STEP B)

Reset

1.Unplug 10 pin harness. Press and hold the programming button while re-plugging 10 pin harness to module. 2.Release the programming button, within 2 -3 seconds the LED confirms reset status by rapidly flashing. 3.The module is now reset and has returned to default setting.

Page 2

SYSTEM

OR

2

Data 2 Data (Optional)

SYSTEM

INSTALLATION NOTES:

*The wiring of some older model Passlock 1 may also have the following color sequence: Black/White, Black (GND), Black (DATA) ** The Equinox is a PASSLOCK 2 type even though it does not have a starter wire.

TECH NOTE: * For some vehicles, (Equinox) may not be required to have transmission in Drive (D) position

ADDITIONNAL INFORMATION

SUBJECT: CAVALIER,SUNFIRE 1999 OR LESS(PASSLOCK SUPPLIED WITH BULB TEST) Our technical department has noticed that on certain vehicles, such as Cavalier and Sunfire 1999 or less, a voltage residue coming from the starter, after vehicle is started, is present as a pulse during a few seconds . This problem only occurs on some vehicles. So, with test light, after key is back to ignition position, after being started, starter wire is to be tested . The cut must be instantly. If not the case, install 12 amp diode as mentionned in diagram below. This is to rectify situation.

SOLUTION #1

IGNITION SWITCH

SOLUTION #2

+12V BAT

FIREWALL

87 87A 86 30

IGNITION SWITCH

FIREWALL

85

X

STARTER KILL "CLUTCH SWITCH" (MANUAL CAR) (OPTIONNAL)

VIOLET

USE TWO 6 AMPERE DIODES Make connection closest to firewall

STARTER

X

STARTER KILL "CLUTCH SWITCH" (MANUAL CAR) (OPTIONNAL)

VIOLET

USE 1 RELAY SPDT TYPE Make connection closest to firewall

STARTER

"STARTER" WIRE

"STARTER" WIRE

GM Passlock 1 & 2 & VATS & Saturn Ion Self Learning (PLXR) PLXR (replacement part PLJX) is an auto learning unit designed to bypass all GM equipped with Passlock I and Passlock II, VATS & Saturn Ion.

Information

XK06-PLXR ENG.03 sd20060525.cdr

3 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

625860


Notice: fwrite(): send of 206 bytes failed with errno=104 Connection reset by peer in /home/readbag.com/web/sphinxapi.php on line 531