Read TIB-515 Trane Interface Board Rev. 1c text version

VENSTAR

Venstar Interface Board

SAFETY CONSIDERATIONS

MODEL TIB-515

IMPORTANT: READ ALL OF THESE INSTRUCTIONS BEFORE INSTALLING THE TIB-515.

Read and follow the manufacturer instructions carefully. All wiring must conform to local and national electrical codes. Improper wiring or installation may damage the sensor. Recognize safety information. This is the safety alert symbol . When the safety alert symbol is present on equipment or in the instruction manual, be alert to the potential for personal injury. Understand the signal words DANGER, WARNING, and CAUTION. These words are used with the safety alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies a hazard which could result in personal injury or death. CAUTION is used to identify unsafe practices which may result in minor personal injury or property damage.

GENERAL

The TIB-515 allows the use of a conventional thermostat with your Trane HVAC unit.

TIB-515 Installation

WARNING

Turn off power to the HVAC unit before wiring. Death or injury from electric shock could result.

Turn off power to the HVAC unit. Remove the access panel and the front panel of the control box. The TIB-515 should be installed to the right of the Unitary Control Processor (UCP) using the provided screws (see below).

TRANE HVAC CONTROL BOX

INSTALL THE TIB-515 TO THE RIGHT OF THE UCP

J2

TEST

LTB

TEST

1 1 2 3

2 20 19 18 17 16 15 14 13 12 11

UCP

J7

TIB-515

J1

4 5 6 7 8 9 10

Venstar Inc. - 05/07 - Patents Pending

P/N 88-566

Rev. 1

VENSTAR

TIB-515 Wiring

At the UCP board: Remove the P7 connection cable from the J7 terminal block. At the TIB-515 board: Install the P7 connection cable on the J1 terminal block. Connect the J2 terminal block of the TIB-515 to the J7 terminal block of the UCP, using the included TIB515 connnection cable.

Venstar Interface Board

MODEL TIB-515

BEFORE

TEST

LTB

TEST

1 1

2 20 19 18 17 16 15 14 13 12 11

J2

2 3

P7 J7

UCP

TIB-515

J1

4 5 6 7 8 9 10

AFTER

TEST

LTB

TEST

1 1

2 20 19 18 17 16 15 14 13 12 11

J2

2 3 4 5 6 7 8

UCP

J7 P7

TIB-515

J1

9 10

Thermostat Wiring

Conventional Thermostat Wiring

TEST TEST

Heat Pump Thermostat Wiring

TEST TEST

C o n n e c t y o u r Y1 conventional or h e a t p u m p W2 thermostat to the Trane HVAC unit Y2 terminal block as shown.

1 1 2 3 4 5 6 7 8 9

2 20 19 18 17 16 15 14 13 12 11

Y1 Y2 G O W2 R C

1 1 2 3 4 5 6 7 8 9 10

2 20 19 18 17 16 15 14 13 12 11

W1 G R C

10

Place the self-adhesive wiring diagram on the dead front cover and replace all of the panels for the HVAC unit.

Venstar Inc. - 05/07 - Patents Pending P/N 88-566 Rev. 1

Information

TIB-515 Trane Interface Board Rev. 1c

2 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

424319


Notice: fwrite(): send of 202 bytes failed with errno=104 Connection reset by peer in /home/readbag.com/web/sphinxapi.php on line 531