Read NISSAN RECALL CAMPAIGN BULLETIN text version

Classification:

Reference:

Date:

RA09-005

NTB10-032

February 26, 2010

2004-2008 TITAN; REAR AXLE SEAL LEAKS

APPLIED VEHICLES: 2004-2008 Titan (A60)

IF YOU CONFIRM The rear axle assembly is leaking gear oil from the right and/or left hand axle seal, AND No noise or vibration is coming from the rear final drive gears and side bearings.

ACTION Install the new axle shaft assembly--which includes a new retainer, axle bearing, oil seal, bearing cage, and ABS rotor--listed in the Parts Information table. NOTE: Do not replace the entire rear axle assembly for this incident, if it should occur.

IMPORTANT: The purpose of "ACTION" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service Procedure as it contains information that is essential to successfully completing the repair.

Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/4

PARTS INFORMATION Applicable Rear Final Drives(1)(2) 43003-7S26A 43003-7S27A 43003-7S36A 43003-7S37A 43003-7S200 43003-7S220 43003-7S300 43003-7S320 43003-ZH06D 43003-7S322 43003-7S37B 43003-ZH05D DESCRIPTION PART # QUANTITY

SFT ASSY-RR AXLE

38162-8S10A

1

SFT ASSY-RR AXLE, RH SFT ASSY-RR AXLE, LH

38162-ZH06D 38163-8S10A

1 1

(1) Use the Electronic Parts Catalog (FAST or equivalent) to determine which Rear Final Drive is in the vehicle. (2) DO NOT order the Rear Final Drive. These part numbers are listed only to identify which Rear Axle Shaft Assembly should be ordered for the vehicle you are working on.

CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Rpl rear axle shaft assy (one side) (1) NX17AA ZR 53 0.8 Rpl rear axle shaft assy (both sides) (1) NX18AA ZR 53 1.5 (1) Reference the Parts Information Table and use the applicable Rear Final Drive part number as the Primary Failed Part.

SERVICE PROCEDURE 1. Remove the ABS sensor, and position it out of the way. · See the BRC section of the applicable Electronic Service Manual for removal instructions.

2. Remove the rear brake rotor. · See the BR section of the applicable Electronic Service Manual for removal instructions.

3. Disconnect the parking brake cable from the parking brake assembly. · See the PB section of the applicable Electronic Service Manual for instructions.

2/4 NTB10-032

4. Remove the four (4) axle shaft bearing cage nuts and lock washers.

Axle shaft bearing cage nut Figure 1

5. Remove the axle shaft assembly using suitable tools. CAUTION: · · The axle shaft bearing cup may stay in place in the axle shaft housing. Remove the cup carefully so as not to damage the inner surface of the axle shaft housing. If gear lubricant contacts brake shoe material, clean immediately using a Nissan approved brake cleaner.

Figure 2

3/4 NTB10-032

6. Remove the back plate, torque member, and parking brake assembly.

7. Check the exterior and inner machined surfaces of the axle shaft housing for deformation and cracks. Clean/replace, if necessary.

8. Reinstall the back plate and torque member.

9. Install the new axle shaft assembly listed in the Parts Information table into the axle shaft housing.

10. Reinstall the remaining parts in the reverse order of removal.

4/4

NTB10-032

Information

NISSAN RECALL CAMPAIGN BULLETIN

4 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

884133


Notice: fwrite(): send of 193 bytes failed with errno=104 Connection reset by peer in /home/readbag.com/web/sphinxapi.php on line 531