Read 02_HVAC&R_0610.pdf text version

butterfly valves

hyflo mkv cast iron hyflo mkv ductile iron hyflo mkv watermark (ucv) cast iron stainless steel hygienic 2.1 2.6 2.8 2.11 2.13

hyflo mkv cast iron butterfly valve

Specification General purpose butterfly valve. conforms to en 593 standards. iso 9001 certified manufacturer. Wafer or lugged cast iron body. stainless steel disc and stem. ePDm or nbr seats. as2129 table e flange connection as standard. ansibs16.1/5 #125/150 connection available on request. DeSign featureS 1. aGa approved for gas service. aGa certificate no. 4030 applies to Dn50Dn150 valves to a maximum pressure of 8 bar (800 kPa) with an nbr seat. available to suit table e or ansi 150 flanges. 2. the operating lever is cast ductile iron for long life in all but the most corrosive environments. 3. lever handles have s/s 304 10 position notch plates and memory stop plates are also available. Gear operators have an infinite number of positions. 4. a raised key section on the liner fits into a matching keyway on the inside of the valve body to provide greater flexibility at the disc seating area and prevent liner `rollout', a condition where the seat can come away from the body when high velocities occur or the valve is installed incorrectly. 5. the moulded seat design is easily replaced in the field, provides isolation of the body from the service fluid and acts as a gasket face for sealing. 6. the acetal bushing takes care of any operator induced side thrust loads and when combined with chevron type secondary stem seal ensures trouble free operation. 7. the webbed flange design of wafer body ensures correct and positive alignment between flanges one of the criteria for good butterfly valve operation. preSSure/temperature rating for general fluid service up to 1400 kPa (200Psi). Lugged valve suitable for full rated pressure in downstream dismantled condition, provided all installation requirements are met. aGa approved to 800 kPa (116Psi) for sizes Dn50Dn150 with nbr seat. nbr seat: 10°c to +90°c (0°c to +80°c continuous). ePDm seat: 15°c to +120°c (5°c to +100°c continuous). materiaL Specification ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 component body Disc seat upper stem lower stem Packing Packing Gland snap ring top retainer top retainer bolts bottom Plug operating lever notch Plate material cast iron 304 stainless steel ePDm or nitrile (nbr)* 304 stainless steel 304 stainless steel ePDm or nitrile (nbr)* acetal carbon steel 304 stainless steel 304 stainless steel nickel Plated mild steel cast Ductile iron 304 stainless steel 8. the valve has an extended neck for insulated pipe services. 9. Pinless disc design, eliminates one less leak path past the disc. 10. valves can also be supplied with pneumatic, electric or hydraulic actuators and with all accessories such as limit switches, solenoid valves, manual override etc. 11. valves can also be supplied with the disc diameter undercut to ensure minimum torque and smallest possible actuator size for throttling or low pressure shutoff actuated valve applications. 12. the hyflo mkv has a spherically machined disc to ensure improved sealing from valve internals under higher operating pressures. stem and bushings etc never come into contact with service fluid. supplied as standard with either lever or gearbox. an extra leaver, gearbox, spare seats and memory stop kits can also be supplied separately. note: for matching bolt and nut sizes, lengths and qty's refer to page 1.26 of tradelink industrial catalogue. note: for service other than hvac water and aGa service please consult for compatibility of seat elastomer and disc material with service fluid.

butterfly valves hyflo mkv cast iron

* ePDm as standard, nbr for aGa approved valves.

June 2010

2.1

hyflo mkv cast iron butterfly valve

butterfly valves hyflo mkv cast iron

VaLVe DimenSionS - mm

size Ød Øg h1 h2 h3 h4 l t ØW a B ØD kg waf kg lugg 50 51.5 90 75 130 33 238 43 12 32 9.5 30 14 2.8 3.9 65 63.5 107 80 137 33 250 46 12 47 9.5 30 14 3.7 5.0 80 78.0 125 100 157 33 290 46 12 66 11.8 30 16 4.2 6.6 100 101.5 146 110 171 33 314 52 12 89 11.8 30 16 4.8 8.2 125 125.0 179 123 184 33 340 56 12 113 14.5 30 19 7.1 10 150 148.0 206 143 203 33 379 56 12 139 14.5 30 19 8.8 12 200 198.0 257 175 238 33 446 60 12 191 14.5 30 19 13 19 250 248.0 312 210 270 65 545 68 16 242 * 60 22 20 30 300 298.0 362 245 310 65 620 78 16 291 * 60 28 38 47

* Dn250Dn300 are keyway instead of double D, keyway width x depth 8 x 4, key 8 x 7. Weight in kg is approximate only.

fLange DriLLing DimenSionS aS2129 `e' - mm

size ØPcD n h waf h lugg 50 114 4 18 m16 65 127 4 18 m16 80 146 4 18 m16 100 178 8 18 m16 125 210 8 18 m16 150 235 8 22 m20 200 292 8 22 m20 250 356 12 22 m20 300 406 12 26 m24

for ansi flange drilling dimensions see page 1.18.

gearbox DimenSionS - mm

to fit size e h l W kg 50 45 74 165 150 5.5 65 45 74 165 150 5.5 80 45 74 165 150 5.5 100 45 74 165 150 5.5 125 45 74 165 180 5.5 150 45 74 165 180 5.5 200 45 74 185 220 6.5 250 63 85 250 260 9.5 300 63 85 250 260 9.5

lugged style

Wafer style

Gearbox

2.2

the information provided in this catalogue is based on original manufacturers' designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.

hyflo mkv cast iron butterfly valve

LeVer HanDLe DimenSionS - mm

size a B l kg 50 9.5 23 285 0.88 65 9.5 23 285 0.88 80 11.8 23 285 0.88 100 11.8 23 285 0.88 125 14.5 23 285 0.88 150 14.5 23 285 0.88 200 14.5 23 385 1.03 250 62 485 2.7 300 62 485 2.7

butterfly valves hyflo mkv cast iron

top fLange mounting DimenSionS to iSo5211

size type Øn Øm m Øz 50 f07 90 70 4 10 65 f07 90 70 4 10 80 f07 90 70 4 10 100 f07 90 70 4 10 125 f07 90 70 4 10 150 f07 90 70 4 10 200 f07 90 70 4 10 250 f10 125 102 4 12 300 f10 125 102 4 12

VaLVe operating torque - nm

size dP 6 Bar dP 10 Bar dP 16 Bar 50 18 21 23 65 23 26 27 80 30 32 35 100 38 50 51 125 57 65 79 150 85 98 112 200 158 169 239 250 250 292 356 300 347 501 525

based on water as the fluid with temperature range +1°c to +80°c. at least one operation cycle per month and a flow velocity in the pipe not more than 4m/s.

VaLVe fLow coefficientS - cv (uSgpm)

size 20° open 30° open 40° open 50° open 60° open 70° open 80° open 90° fully open cv = 1.16 kv Dn50 Dn200 Dn250 Dn300 50 10.8 16.4 25.5 41.6 67.3 108.4 167.3 200.0 65 18.3 27.6 43.0 70.1 114.0 184.1 282.2 338.4 80 27.8 41.8 65.4 106.6 171.9 278.5 428.0 512.1 100 42.3 65.0 101.9 165.9 269.9 435.8 667.8 800.1 125 68.3 101.9 159.4 260.2 419.6 680.8 1045.1 1250.0 150 97.6 147.4 229.8 375.1 607.1 979.0 1504.7 1800.7 200 173.5 261.3 408.7 666.7 1079.8 1741.1 2674.5 3201.4 250 271.0 409.8 637.5 1040.7 1686.9 2720.0 4179.3 5003.2 300 390.3 588.7 918.2 1499.3 2429.5 3918.0 5083.4 7203.9

top flange

lever

June 2010

2.3

hyflo mkv cast iron butterfly valve

butterfly valves hyflo mkv cast iron

correct inStaLLation before inStaLLation cHeck 1. Pipe flanges are free from weld spatter or swarf. 2. the flanges are on the same centreline and their faces are parallel. 3. the pipe internal does not contain objects that will obstruct the disc from fully opening. 4. the pipe flanges internal diameters are within the above minimum and maximum dimensions. this is to make sure the disc does clear the inside of the flange and the flange fully seals with the raised gasket face of the seat. 5. Do not weld near the valve. 6. Do not use flange gaskets or sealing compounds. inStaLLation 1. operate valve fully before and after installation. 2. semiopen the valve so that the disc does not protrude outside of body. this prevents damage to the disc and reduces initial torque. 3. separate pipe flanges enough to clear valve body and liner faces to prevent damage to the seat during installation. insert valve. 4. manually loose fit flange bolts and centre valve bore with pipe/ flange bore. 5. open valve fully to ensure no contact between disc and pipe or flanges. 6. Progressively tighten bolts in diagonal sequence until metal to metal contact is achieved between the valve body and flanges. 7. operate valve several times to ensure no obstruction to disc travel. pipe fLange iD - mm

size min iD max iD 50 47 60 65 60 76 80 72 90 100 96 114 125 122 140 150 148 168 200 198 219 250 248 275 300 298 323

2.4

the information provided in this catalogue is based on original manufacturers' designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.

hyflo mkv cast iron butterfly valve

HyfLo mkV caSt iron butterfLy VaLVe coDeS

comPlete ePDm t/e valves lugged w/-lever Wafer w/-lever lugged w/-gearbox Wafer w/-gearbox aGa luGGeD nBr valves table e ansi 150 (imP) ansi 150 (metric) nBr t/e lugged lever 50 076716 076728 076742 076660 50 076648 076871 076849 65 076717 076729 076743 076661 65 076649 076872 076850 80 076718 076730 076744 076662 80 076650 076874 076852 100 076719 076731 076745 076663 100 076651 076875 076854 125 076720 076732 076747 076664 125 076652 076876 076856 150 076721 076733 076748 076665 150 076653 076877 076878 076659 200 076722 076734 076749 076666 250 076723 076735 076750 076668 300 076724 076736 076753 076669

butterfly valves hyflo mkv cast iron

sPares Gear Box memory stop kit lever kit spare seats for previous models ePDm mkiv seat nBr mkiv seat mk3 ePDm mk3 nBr mk2 ePDm mk2 nBr mk1 nBr

50 076686 075090 076837 075341 075516 075000 075016 076637 076676

65 076686 075090 076837 075342 075517 075004 075017 076639 076677 076671

80 076687 075091 076838 075343 075518 075006 075018 076641 076678

100 076687 075091 076838 075344 075519 075008 075019 076643 076679 076675

125 076688 075092 076839 075345 075520 075009 075024 076644 076680 076685

150 076688 075092 076839 075346 075521 075010 075040 076645 076681 076696

200 076689 075092 076840 075347 075522 075012 075042 076647 076682

250 076690 076841 075348 075523 075013 075047 076657 076683 076698

300 076691 076842 075349 075524 075014 075048 076667 076684

standard valves ePDm seat, aGa valves nbr seat.

gear operator reDuction ratioS

Dn50 - Dn200 Dn250 - Dn300 24:1 30:1

memory stop kit

June 2010

2.5

hyflo mkv Ductile iron butterfly valve

butterfly valves hyflo mkv Ductile iron

Specification General purpose butterfly valve. conforms to en 593 standards. iso 9001 certified manufacturer. Wafer or lugged ductile iron body. stainless steel disc and stem. ePDm seats. as2129 table e flange connection as standard. ansibs16.1/5 #125/150 connection available on request. preSSure/tempurature rating for general fluid service up to 1400 kPa (200psi). lugged valve suitable for 60% of full rated pressure, 800 kPa, in downstream dismantled condition, provided all installation requirements are met. ePDm seat: 15°c to +120°c (5°c to +100°c continuous). materiaL Specification

lugged style

ref. component 1 2 3 4 5 6 7 8 9 10 11 12 body Disc seat upper stem lower stem Packing Packing Gland snap ring top retainer top retainer bolts bottom cover bottom bolts

material Ductile iron 304 stainless steel ePDm 304 stainless steel 304 stainless steel ePDm brass carbon steel nickel Plated or epoxy Plated steel nickel Plated mild steel nickel Plated or epoxy Plated steel nickel Plated mild steel

VaLVe DimenSionS - mm

size Ød Øg h1 h2 h3 h4 l t ØW B Wafer style ØD key t1 t2 b 350 346.0 410 280 325 65 670 78 17 343 60 28 8x7 4.0 3.0 8.0 39 59 400 395.0 468 315 375 75 765 102 20 386 70 38 12x8 5.0 3.0 12.0 75 82 450 452.0 526 335 400 75 810 114 20 438 70 38 12x8 5.0 3.0 12.0 92 110 500 489.5 577 385 435 100 920 127 23 476 90 45 14x9 5.5 3.5 14.0 110 162 600 579.0 677 450 500 100 1050 154 23 562 90 55 14x9 5.5 3.5 14.0 169 264

for further details on installation of rubber lined butterfly valves see page 2.4. note: for matching bolt and nut sizes, lengths and qty's refer to page 1.26 of tradelink industrial catalogue. note: for service other than hvac water please consult for compatibility of seat elastomer and disc material with service fluid.

kg waf kg lugg

Weight in kg is approximate only.

2.6

the information provided in this catalogue is based on original manufacturers' designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.

hyflo mkv Ductile iron butterfly valve

fLange DriLLing DimenSionS aS2129 `e' - mm

size ØPcD n h waf h lugg 350 470 12 26 m24 400 521 12 26 m24 450 584 16 26 m24 500 641 16 26 m24 600 756 16 33 m30

top fLange DimenSionS to iSo5211

size type Øn Øm m Øz 350 f10 125 102 4 12 400 f14 175 140 4 18 450 f14 175 140 4 18 500 f16 210 165 4 22 600 f16 210 165 4 22

butterfly valves hyflo mkv Ductile iron

for ansi flange drilling dimensions see page 1.18.

pipe fLange iD - mm

size min iD max iD 350 350 361 400 395 412 450 450 463 500 485 510 600 570 585

gearbox DimenSionS - mm

to fit size e h W l 30:1 40:1 50:1 kg 350 63 85 315 250 10 400 82 90 405 300 19 450 82 90 405 300 19 500 100 112 405 310 32 600 100 112 405 310 32

gear operator reDuction ratioS

Dn350 Dn400 - Dn450 Dn500 - Dn600

VaLVe operating torque - nm

size dP 6 Bar dP 10 Bar dP 16 Bar 350 499 619 1389 400 697 802 1851 450 936 1150 2264 500 1208 1485 2791 600 2535 2955 5155

based on water as the fluid with temperature range +1°c to +80°c. at least one operation cycle per month and a flow velocity in the pipe not more than 4m/s.

VaLVe fLow coefficientS - cv (uSgpm)

top flange size 20° open 30° open 40° open 50° open 60° open 70° open 80° open 90° fully open cv = 1.16 kv 350 532.3 802.2 1250.0 2040.3 3292.4 5331.7 8190.5 9804.7 400 694.9 1047.3 1632.7 2665.8 4318.0 6964.3 10698.0 12806.6 450 878.1 1324.8 2066.3 3372.7 5462.0 8813.8 13540.6 16208.6 500 1085.2 1635.9 2550.9 4164.1 6746.4 10882.3 16715.9 20010.5 600 1562.2 2356.9 3674.1 5996.2 9714.7 15669.8 24070.5 28814.6

traDeLink inDuStriaL HyfLo mkV DuctiLe iron butterfLy coDeS

comPlete valve lugged w/-gearbox Wafer w/-gearbox spares Gearbox ePDm seat nBr seat Gearbox 076692 075350 075525 076694 075351 075526 076694 075352 075527 076704 075353 075528 076704 075356 075530 350 076755 076670 400 076761 076672 450 076763 076673 500 076765 076708 600 076769 076714

June 2010

2.7

hyflo mkv Watermark butterfly valve

butterfly valves hyflo mkv Watermark

Specification Potable water service butterfly valve. Watermark approval evaluated to ats 5200.012 2005 certificate no. Wmka20022. conforms to en 593 standards. iso 9001 certified manufacturer. cast iron body with fbe coating to 350 microns. lugged valve body pattern stocked as standard. Wafer valve body available on request. ePDm grade seats in accordance with as 4020. as2129 table e flange connection as standard. valve sizes stocked with lever Dn50 to Dn150, with gear operator Dn100 to Dn300. top flange mounting dimensions to iso5211. materiaL Specification ref. component 1 2 3 4 5 6 7 8 9 10 11 12 13 body Disc seat upper stem lower stem Packing Packing Gland snap ring top retainer top retainer bolts bottom Plug operating lever notch Plate material cast iron with fbe coating 350 microns cf8m stainless steel Peroxide cured ePDm to as 4020 316 stainless steel 316 stainless steel ePDm acetal carbon steel 304 stainless steel 304 stainless steel nickel Plated mild steel cast Ductile iron 304 stainless steel

DeSign featureS 1. Watermark approval to ats 5200.012 2005, certificate no. Wmka20022 for potable water service in valve sizes Dn50 to Dn300. 2. supplied as standard with either a lever (Dn50Dn150) or gearbox (Dn100Dn300). memory stop kits or actuators and accessories are available. 3. Distinquishable from the standard hyflo mkv valve because of the valve colour, the Watermark valve is blue, the standard valve is green with a yellow lever 4. seat design to prevent 'roll out' when high velocities occur or valve is installed incorrectly. 5. seat design is easily replaced in the field, isolates the fluid from the valve body and acts as a gasket face for seating.

memory stop kit

6. the acetal bushing and chevron secondary stem seal ensures trouble free operation. 7. the valve has an extended neck for insulated pipe services. 8. Pinless disc design eliminates one less leak path. 9. the hyflo mkv has a spherically machined disc to ensure improved sealing from valve internals under higher operating pressures. stem and bushings etc never come into contact with service fluid.

preSSure/temperature ratingS for potable water service up to 1400 kPa (200 Psi). lugged valve suitable for full rated pressure in downstream dismantled condition, provided all installation requirements are met. ePDm seat: 15°c to +120°c (5°c to +100°c continuous) note: for matching bolt and nut sizes. lengths and qty's refer to page 1.26. for installation instructions refer to page page 2.4. for top flange mounting dimensions to iso5211 refer to page 2.3. note: for service other than Potable water please consult with us for compatibility of seat elastomer and disc materials with service fluid.

2.8

the information provided in this catalogue is based on original manufacturers' designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.

hyflo mkv Watermark butterfly valve

VaLVe DimenSionS - mm

size Ød Øg h1 h2 h3 h4 l t ØW a B ØD kg waf kg lugg 50 51.5 90 75 130 33 238 43 12 32 9.5 30 14 2.8 3.9 65 63.5 107 80 137 33 250 46 12 47 9.5 30 14 3.7 5.0 80 78.0 125 100 157 33 290 46 12 66 11.8 30 16 4.2 6.6 100 101.5 146 110 171 33 314 52 12 89 11.8 30 16 4.8 8.2 125 125.0 179 123 184 33 340 56 12 113 14.5 30 19 7.1 10 150 148.0 206 143 203 33 379 56 12 139 14.5 30 19 8.8 12 200 198.0 257 175 238 33 446 60 12 191 14.5 30 19 13 19 250 248.0 312 210 270 65 545 68 16 242 * 60 22 20 30 300 298.0 362 245 310 65 620 78 16 291 * 60 28 38 47

butterfly valves hyflo mkv Watermark

* Dn250Dn300 are keyway instead of double D, keyway width x depth 8x4, key 8x7. Weight in kg is approximate only.

fLange DriLLing DimenSionS aS2129 `e' - mm

size ØPcD n h waf h lugg 50 114 4 18 m16 65 127 4 18 m16 80 146 4 18 m16 100 178 8 18 m16 125 210 8 18 m16 150 235 8 22 m20 200 292 8 22 m20 250 356 12 22 m20 300 406 12 26 m24

for ansi flange drilling dimensions see page 1.18.

gearbox DimenSionS - mm

to fit size e h l W kg 50 45 74 165 150 5.5 65 45 74 165 150 5.5 80 45 74 165 150 5.5 100 45 74 165 150 5.5 125 45 74 165 180 5.5 150 45 74 165 180 5.5 200 45 74 185 220 6.5 250 63 85 250 260 9.5 300 63 85 250 260 9.5

lugged style

Wafer style

Gearbox

June 2010

2.9

hyflo mkv Watermark butterfly valve

butterfly valves hyflo mkv Watermark

LeVer HanDLe DimenSionS - mm

size a B l kg 50 9.5 23 285 0.88 65 9.5 23 285 0.88 80 11.8 23 285 0.88 100 11.8 23 285 0.88 125 14.5 23 285 0.88 150 14.5 23 285 0.88 200 14.5 23 385 1.03 250 62 485 2.7 300 62 485 2.7

VaLVe operating torque - nm

size dP 6 Bar dP 10 Bar dP 16 Bar 50 18 21 23 65 23 26 27 80 30 32 35 100 38 50 51 125 57 65 79 150 85 98 112 200 158 169 239 250 250 292 356 300 347 501 525

based on water as the fluid with temperature range +1°c to +80°c. at least one operation cycle per month and a flow velocity in the pipe not more than 4m/s.

VaLVe fLow coefficientS - cv (uSgpm)

size 20° open 30° open 40° open 50° open 60° open 70° open 80° open 90° fully open cv = 1.16 kv 50 10.8 16.4 25.5 41.6 67.3 108.4 167.3 200.0 65 18.3 27.6 43.0 70.1 114.0 184.1 282.2 338.4 80 27.8 41.8 65.4 106.6 171.9 278.5 428.0 512.1 100 42.3 65.0 101.9 165.9 269.9 435.8 667.8 800.1 125 68.3 101.9 159.4 260.2 419.6 680.8 1045.1 1250.0 150 97.6 147.4 229.8 375.1 607.1 979.0 1504.7 1800.7 200 173.5 261.3 408.7 666.7 1079.8 1741.1 2674.5 3201.4 250 271.0 409.8 637.5 1040.7 1686.9 2720.0 4179.3 5003.2 300 390.3 588.7 918.2 1499.3 2429.5 3918.0 5083.4 7203.9

traDeLink inDuStriaL HyfLo mkV watermark butterfLy VaLVe coDeS

size lugged w/- lever lugged w/- gear op 50 074604 65 074605 80 074606 100 074607 074610 125 074608 074611 150 074609 074612 074613 074614 074615 200 250 300

Dn50 Dn200

Dn250 Dn300

lever

2.10

the information provided in this catalogue is based on original manufacturers' designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.

(ucv) cast iron butterfly valve

Specification throttling or low pressure applications for mechanical services or general industry. conforms to bs5155 specification, wafer, cast iron body, stainless steel disc and stem, ePDm seat, as2129 table e flange connection as standard. operator mounting in accordance with iso 5211/1/2/3. preSSure/temperature rating for general fluid service up to 300 kPa (43psi). 120°c ePDm food grade. Valve Velocity Limits fluids 10 m/s Gases 65 m/s materiaL Specification ref. component 1 2 3 4 5 bushing stem Disc body seat material acetal 316 stainless steel 316 stainless steel cast iron ePDm

butterfly valves (ucv) cast iron

DeSign featureS 1. the Disc diameter is undercut to ensure minimum torque and smallest possible actuator size for throttling or low pressure shut off actuated valve applications. 2. Pinless Disc design eliminates possible leak path or risk of pin failure. 3. stem rention via circlip ensures stem cannot blow out if the valve is over pressurised. 4. Primary and secondary sealing features, an interference fit between seat and disc, and seat and stem, do not rely on outside flanges. 5. seat retention design minimises distortion/movement of the seat. 6. moulded double orings on the seat between the seat and the flange, and seat and stem surface maximise sealing. 7. seat is not bonded to the body and is replaceable, enabling extended service life. 8. extended neck design for insulated pipe services. 9. locating holes on the body wafer essential for alignment and proper installation. 10. Disc is manufactured from 316 stainless steel for corrosion protection.

June 2010

2.11

(ucv) cast iron butterfly valve

butterfly valves (ucv) cast iron

VaLVe DimenSionS - mm

size a B c D e f G h shaft Dia shaft flat 50 90 32 140 42.9 94 53 55 30.6 14.0 9.5 65 90 32 152 46 112 68 65 50 14.0 9.5 80 90 32 159 46 128 82 75 69 14.0 9.5 100 90 32 178 52.3 158 103 94 89 19.1 12.7 125 90 32 191 55.6 190 129 105 115.6 19.1 12.7 150 90 32 203 55.6 210 152 123 141.5 22.0 15.9 200 127 32 241 60.5 266 202 149 192.3 22.0 15.9 250 127 50 273 68.3 330 252 198 242.6 30.0 24.0 300 127 50 311 77.7 375 302 225 292.5 30.0 24.0

top fLange DimenSionS

no. holes Dia. holes Bolt circle 4 9 70 4 9 70 4 9 70 4 9 70 4 9 70 4 9 70 4 11 102 4 11 102 4 11 102

standard valves are bareshafted for actuation.

VaLVe operating torque - nm

size Wet 3 Bar Dry 3 Bar 50 7.5 11 65 8.5 13 80 13 20 100 17 25 125 26 49 150 38 57 200 68 102 250 114 171 300 163 244

VaLVe fLow coefficientS - uSgpm

size 20° 30° 40° 50° 60° 70° 80° 90° open 50 7 16 28 49 77 128 198 219 65 10 23 42 68 108 178 288 316 80 15 36 65 109 167 278 427 498 100 26 61 108 178 275 458 715 815 125 43 98 177 278 447 737 1095 1290 150 59 138 247 398 637 1097 1590 1895 200 108 247 437 687 1100 1795 2790 3290 250 178 396 705 1100 1795 2995 4590 5390 300 256 587 995 1697 2695 4398 6790 7990

weigHt - kg

size kg 50 2.9 65 3.8 80 4.3 100 5.4 125 7.2 150 9 200 15.8 250 22.6 300 39.4

traDeLink inDuStriaL (ucV) caSt iron butterfLy coDeS

size Wafer 50 075058 65 075059 80 075060 100 075061 125 075062 150 075063 200 075064 250 300

2.12

the information provided in this catalogue is based on original manufacturers' designs and specifications and subject to change without notice. crane Distribution accepts no liability for the accuracy of the information or the availability of products.

stainless steel hyGienic butterfly valve

Specification hygienic butterfly valve. fully forged stainless steel. finish body 180 grit disk 400 grit. spring loaded lever with four (4) locking positions. buttweld connection. all parts are interchangeable within the respective size. preSSure/temperature rating up to 1100 kPa (160psi) at 170°c or down to minus 50°c in closed position. materiaL Specification ref. component 1 2 3 4 5 6 body Disc stem liner handle handle Grip material 316 stainless steel 316 stainless steel 316 stainless steel silicon as standard 316 stainless steel Plastic

butterfly valves stainless steel hyGienic

available with silicon or viton replaceable trim.

DimenSionS - mm

size a B 25 121 24 40 121 24 50 121 26 65 121 27 80 162 32 100 162 40

operating torque - nm

size torque 25 8 40 12 50 14 65 22 80 28 100 36

also available with mounted actuator.

traDeLink inDuStriaL generic Hygienic butterfLy coDeS

size 304 ss 316l ss 314 lever, 4 position 088129 25 088101 088113 32 088103 088115 40 088105 088117 50 088107 088119 088127 088125 088131 65 80 088109 088121 100 088111 088123

June 2010

2.13

Information

14 pages

Find more like this

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

371981


You might also be interested in

BETA