Read m20080428115739.pdf text version

Pricelist 2008 - (01/04/2008) MagiZinc®

Made in IJmuiden

MagiZinc® price list

General

Basis price: Price extras: General conditions: Validity: EuroNorm: quotation upon request. the appropriate extras to be supplemented to or to be deducted from the basis price are shown below. as mentioned in the Corus Strip Products IJmuiden price list dated 01-04-2008 also apply for this price list. this price list is valid from 01-04-2008. tolerances and chemistry are according to EN-norm, coating is MagiZinc®.

Steel for drawing and cold forming Corus

n.a.

EN

EN 10327 DX51D+ZMA DX52D+ZMA DX53D+ZMA DX54D+ZMA

Price extras /t

0 25 50 85

Structural steel Corus

n.a.

EN

EN 10326 S220GD+ZMA S250GD+ZMA S280GD+ZMA S320GD+ZMA S350GD+ZMA

Price extras /t

0 10 20 28 45

High Strength steel

Corus Low Alloyed HSS n.a. EN EN 10292 HX220LAD+ZMA 1) HX260LAD+ZMA HX300LAD+ZMA HX340LAD+ZMA HX380LAD+ZMA HX420LAD+ZMA

1)

Price extras /t 20 30 40 50 70 75

Not in EN 10292

Size extras /t

Width (mm) Thickness (mm) 0,48 < 0,53 0,53 < 0,58 0,58 < 0,68 0,68 < 0,78 0,78 < 0,88 0,88 < 0,98 0,98 < 1,23 600 < 700 245 233 220 191 165 153 138 700 < 800 225 213 195 173 147 136 122 800 < 900 200 188 170 150 134 121 107 900 < 1100 190 178 160 137 121 111 96 1100 < 1300 180 168 150 123 102 95 81 1300 < 1850 180 168 150 120 99 93 79

The size extras reflect a MagiZinc coating of 140 g/m2 (two sides). Other dimensions and coating sizes available upon request. Please consult http://www.cspij-productrange.nl/ or CSPIJ's commercial department for dimension constraints per quality.

Pricelist 2008 - (01/04/2008) MagiZinc®

1. Price extras for surface aspect No spangle/not temperrolled (not skinpassed) A 2. Price extras for reduced tolerances Reduced tolerances to EN 10143 Thickness, width, each Special flatness to EN 10143 Thickness < 0,68 mm Thickness 0,68 < 1,18 mm Thickness 1,18 mm 3. Price extras for special thicknesses

Certificate of compliance 2.1 Test report 2.2 Details of heat analyses Details of heat analyses and mechanical properties Inspection certificate 3.1 Signed by an authorized representative of the works personnel. Inspections will take place at Corus Strip Products IJmuiden. 20 15 10 Other tests Roughness test Coating thickness 6. Price extras for surface treatment

0

0

0 3 5

15

2 2

If a transfer in thickness tolerance in one direction is specified, the calculation of the size extra is based on the resultant average dimension. 4. Price extras for small item quantities and/or coils Quantity in tonnes 20 < 50 50 The minimum quantity that can be ordered is 20 tonnes. Coil weights Coil weights between 5 and 10 tonnes Width in mm 600 < 800 800 < 1100 1100 < 1500 1500

Oiling Passivation 7. Price extras for packing

3 0

10 0

For weighing and invoicing gross equals net. The wood if used in packing is included in the weight. Wrapping Steel strapping Fully paper/film wrapping and steel strapping Steel/hardboard box, paper/film and steel strapping

0 3 5

Upon request 30 30 35

General Packaging materials are to be regarded as non-returnable and should be disposed of properly. 8. Rejection during processing In case of coil deliveries, no complaints will be accepted for less than the mentioned percentages in the table below 100 tonne/item Surface aspect A

*) Calculated over the tonnage of the complete order item **) Calculated over the coil length

Coil weight price extras apply unless the specified coil weight is the result of technical limitations at CSPIJ. Coils under 5 tonnes in weight are not supplied. These rates apply to items from one customer for quantities of one size (width, thickness) and grade for delivery in one consignment to one destination. Specified coil weights must be in balance with the ordered quantity. Welds If recoiling welds are not accepted. 5. Price extras for certificates and other tests Materials testing certificates to EN 10204. At purchaser's choice only one certificate to EN 10204 will be issued, to be agreed on ordering.

< 2 % *)

< 100 tonne/item or coil < 6 % **)

3

9. Allowable under and over shipment a) item 100 tonnes = 20 % b) item > 100 tonnes = 10 %

Corus Strip Products IJmuiden

PO Box 10000 1970 CA IJmuiden The Netherlands T: +31 (0) 251 496126

www.cspij-productrange.nl

Care has been taken to ensure that this information is accurate, but Corus Staal B.V., or any Corus group company, does not accept responsibility or liability for errors or information which is found to be misleading. Copyright 2008 Corus

Information

2 pages

Report File (DMCA)

Our content is added by our users. We aim to remove reported files within 1 working day. Please use this link to notify us:

Report this file as copyright or inappropriate

462318


Notice: fwrite(): send of 198 bytes failed with errno=104 Connection reset by peer in /home/readbag.com/web/sphinxapi.php on line 531