Read LazerTripwireTrain_P1.eps text version
Official Spy Gear Memo
To: From: Re: All Spy Gear Agents Spy Gear Headquarters Lazer Tripwire Training Instructions
Headquarters Hotline: 1-800-247-6570 or www.wildplanet.com/help
The Spy Gear Lazer Tripwire is the ultimate security system. It is important that you practice operating this advanced equipment before you use the gear on a real mission. One slip up on a mission may jeopardize our whole organization! Lazer Tripwire works best in dim to dark places--which is where top-secret security systems are needed most!
Exercise One: Know your equipment
Identify pods LTW-001, LTW-002 and LTW-003. The ID number is located on the side of each pod. IMPORTANT: LTW-001 is the main pod and controls the whole system. LTW-001 is the only pod that can tell you when the system is armed. Do not allow this pod to fall into enemy hands!
Pod ID number
LED indicator light Spring clamps
Exercise Two: Simple set up
Practice creating a simple trap. Then use the trap to protect things, like important documents or other Spy Gear. STEP STEP STEP STEP STEP 1 2 3 4 5
Make sure you are in a dimly lit room. Stand LTW-001 and LTW-002 on a table, facing each other about 12 inches apart. Set the sensitivity switch on both pods to the brighter setting ( ). Switch both pods on. Shine the light beam from LTW-002 Sender into the center of LTW-001 Receptor. The solid red LED indicator will light on LTW-001 when the beam is lined up. TIP: If you cannot find the beam from LTW-002 Sender, place a piece of white paper in front of the sender to locate the beam's position. LTW-002
LED indicator Sender Receptor
STEP 6 Wait five seconds for the system to arm. When armed, LTW-001's LED will begin blinking, and a voice will announce "SYSTEM ARMED". STEP 7 Move your hand through the beam slowly to test the alarm.
Exercise Three: Advanced set up
This exercise will help you set up a more complicated trap--use it to protect your important stuff! This is for advanced agents who have completed exercises one and two. STEP STEP STEP STEP Move LTW-001 off to the side. Stand LTW-003 on the table about 12 inches away from LTW-002. Switch on LTW-002 and LTW-003. Rotate LTW-003 Sender and LTW-002 Receptor so they point at the 3rd point of a triangle. STEP 5 Shine the light beam from LTW-002 Sender into the center of LTW-003 Receptor. When the beam is lined up, LTW-003's red LED indicator will light and begin flashing after five seconds. Sender Sender LTW-002 1 2 3 4
STEP 6 Stand LTW-001 on the spot which forms the 3rd point of the triangle. STEP 7 Switch on LTW-001. STEP 8 Shine the light beam from LTW-001 Sender into the center of LTW-002 Receptor. When the beam is lined up, LTW-002's red LED indicator will light and begin flashing after five seconds. Sender Sender LTW-002 Receptor
Rotate LTW-001 Receptor so that the beam from LTW-003 Sender is hitting the center point. The solid red LED indicator will light on LTW-001 when the beam is lined up. TIP: If this is difficult, move LTW-001 back and forth until LTW-003's light beam shines on the center of LTW-001 Receptor. STEP 10 Wait five seconds for the system to arm. When armed, LTW-001's LED will begin blinking, and a voice will announce "SYSTEM ARMED". STEP 11 Move your hand through each beam slowly to test the alarm.
LAZER TRIPWIRE 70106-4000 PR 9/05
IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT US AT 1-800-247-6570 WWW.WILDPLANET.COM ©2005 Wild Planet Toys, Inc. P.O. Box 194087 San Francisco, CA 94119-4087
©2005 Wild Planet Toys, Inc., San Francisco, CA 94104, USA. All rights reserved. MADE IN CHINA.